I purchased Maytag refrigerator (model # MSD2572VES). The fridge side stopped working. I was told that the vent/chute between the freezer and fridge ices up and prevents the cold air from the freezer to go through the fridge. The tech said that Maytag was sending him a tube of silicone to apply all around freezer and fridge and that this will probably fix the problem. So in other words, because of a design flaw, the refrigerator cannot function without adding silicone (maybe). I believe I purchased a lemon with a design flaw and they want me to accept a permanent band-aid as the solution. Shouldnt I have right to demand another model instead of having to accept a cheap alternative (silicone)? Now, if factory installed parts break off, can you imagine silicone tubed in after the fact where there was no silicone crevasse? I cant imagine it staying on - permanently.

Maytag washer Model #: MVWX655DW - I purchased this machine at Lowes in May of 2016. Always was a loud machine but seemed to work ok. In April 2018 the machine stopped working correctly. The spin cycle would lock up and not finish leaving clothes soaked. Called Lowes and waited for their repairman. He came and said it was the clutch and drive motor. Repair is over $400. Machine is worthless. Huge mistake. Never buy a Maytag. I called Maytag to see if they would warranty it. They basically said, Sorry only a one-year warranty on it. I told them the reason I bought it was it had 10-year warranty on it. They said only certain parts but its the drive motor that is clearly marked on the machine that has the 10-year warranty. I was told, No sorry. What huge waste of money. I am out close to $600 and Lowes only give you a store credit with their protection plan.The credit is not enough to purchase another machine without more out of pocket expenses. I will never buy another Maytag and I would not recommend anyone else does. Their warranty is a huge joke. Their customer service is terrible. Maytag should not even bother sticking the 10-year drive motor warranty on their machines. They do not honor it. My advice do not even consider buying one. You will be out the money and be purchasing a new machine within two years.

Maytag Bravos Model MVWB750wq1 - After only two years, the washing machine finally died. The machine was on a f51 code - hardly anything was in the washer. I also smelled a burning smell - well, that was the pump. The machine was not pumping water out. After the repairman came out, the contract company is saying they are not covering this because there was rust reported by the repairman. How can bearings inside a washing machine be rusted? This is a washing machine, isnt it? How are they building machines that deal with water and rust?! I will never buy another Maytag product - thats a promise. I spent over 2000.00 on this set. Never again.

Maytag french door 2015 refrigerator. Not happy at all. Freezer gets rim frost on sides of pull drawers and the smell is like dirty socks when motor is running! The whole kitchen stinks???

Maytag Centennial Washer - If a wash load becomes off balanced, the machine stops. No signal or buzzer or anything to alert me to this. It happens all the time and wastes a lot of my time. Here I am thinking that the wash is going fine only to find out 2 hours later that it has stopped. Anytime I wash more than 3 items, this happens. I will never buy one again and I am telling everyone not to buy. I will be purchasing a good old fashion washer with a dial gauge so I can spin it any time I needed.

We bought the washer less than a year ago. The washer became off balance with an average load of jeans. The washer shook so violently that it cut our floor, busted our wall, and broke itself. Water covered our floor! We have now been over a month with no washing machine (still paying on it, by the way). We have had to pay to get our clothes washed in the last month = EXPENSIVE! The repair company has been out to our home twice, broken high-quality tools trying to repair the machine, and told by their higher-ups that the washer can still be repaired. Customer service only tells us that we have a repair warranty and the first repair has no time limit.

I bought my Maytag Bravos washer and dryer set about 3.5 years ago when I moved into my home. There was a 20-year old set here that did work, but I wanted something newer and more efficient, so I donated the old set and bought these. Performance of the washer has always seemed mediocre, clothes dont get as clean as I think they should, whites are dingy, despite using hard-water additives and the correct HE products.A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel then start again, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. Its now up to ten F1 errors both at the beginning and end of the cycle. I dont have that kind of time to babysit my washer. I already have a full-time job.I have called Maytag/Whirlpool twice now, both times getting unsatisfactory answers. Even after escalating to the customer service supervisor, I was basically told that it is most likely the control board that is the problem and since Im no longer under warranty (that washer ‘is’ almost 4 years old, maam), Id either have to order the part myself from their supplier (total cost $250 + the risk of DIY), or buy their service package for about $350 which included fixing that problem plus one additional years warranty.I pointed out that for a major household appliance that I (over) paid for, I expect a life of more than 4 years, especially since I had a working 20-year old washer when I moved in here. Since when is this acceptable? I could understand if it were a wear-and-tear part, like a rubber seal or something that moved constantly and would eventually need replaced. But this is the electronics module, something that cant (or at least, shouldnt) be worn down or broken by use or even user error. This is an integral part of the machine, and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer.What angered me even further is that the customer service manager even admitted that models similar to mine had had similar problems, and a free control board was sent to those customers. But my model was not in that range of production, so clearly they have no fault, in their eyes. Apparently, its not even remotely possible that maybe when they determined the range of models they believed to be faulty, mine hadnt been in use long enough to display the same behavior? Maybe the range they selected is too restrictive and they missed some. From the volume of complaints Ive seen online, Id bet that to be the case.I asked to be transferred to their legal department, and was refused because we just dont transfer customers to the legal department. Well, I just dont buy Maytag or Whirlpool anymore, and Im going to do my best to make sure nobody else does either. Im replacing this ** with a different brand, one Ill be sure has tremendous reviews and a manufacturer that will stand behind it.

I too am a victim of the faulty Control Panel that Maytag put on these dishwashers - Model # MDB7749SBM2. $149 for the part and another $149 for service call and labor - almost half the price of what I paid 2 years ago! Should have stuck with the 10 year old builder grade GE I had with the latch door and turn knob! I am in the market for a new stove and microwave - I will never buy another Maytag or Whirlpool product! When is Maytag going to make good to all the customers out there that have experienced the same issue? If yours breaks it is a very easy fix now that I know. You can order the part and it simply unplugs and plugs in the new one. All you have to do is take the door off and it is right there!

On March 2011, I purchased a Maytag dishwasher model #MDB7749AWB1. The dishwasher worked excellent for 16 months. One morning, with dishes loaded and ready to go, the start button would not light up. The other buttons did light up but that did me no good, I need the start button. A few days later, none of the buttons would light up. I found a repair person who said it would cost over $200.00 to make repairs. I refuse to put another penny with no guarantee that this new part would work. I will never ever buy another Maytag appliance. The last inexpensive, unknown manufacturers dishwasher lasted me 13 years. Do not waste your money on this thing.

I am angry that Maytag puts out a washer that hasnt been through quality control. The computer panel is a piece of **, and is not worth $1.00. Do not buy this washer. Shame on Maytag.

Didnt even want to put 1 star but that is the lowest you can give. Maytag microwave less than a year old paid $350. Door clasp broke. Took two weeks to send a repairman out, he came out and of course did not have the part -- took another week to get it. Fixed the door and then he crashed and burned the microwave shorted it out and now it is totally dead. That was 2 1/2 weeks ago. Maytag refuses to replace the microwave and insists that the same incompetent service company come out and fix it. Meanwhile I have to call Maytag every other day to find out when the correct part to repair the microwave will be in. Was told it would be in two days ago. Never got a call to schedule the repair, called today to find out they never even ordered the part. Here goes another week without my microwave. Not only does Maytag have horrible customer service, they manage to find unskilled repair techs with equally horrible customer service! Will never ever buy another May useless Tag appliance again.

We purchased a Maytag Bravos Quiet Series 300 in June 09. The dryer timer has malfunctioned since shortly after purchase, it will add time near the end of the cycle, sometimes as much as an hour or more. We have had factory authorized repair firms (tried several) attempt to fix the problem both during the original warranty and extended warranty periods. They replaced the mother board twice and the moisture sensor on another occasion. All to no avail. Maytag has been worse than useless in the whole situation, and now will do nothing. It seems our only choice is to live with it, keep replacing parts, hasnt helped yet, or buy a new dryer. You can bet it will not be a Maytag!This situation is dangerous, if left unattended when the malfunction occurs the clothes and interior of the dryer get extremely hot. It is a potential fire hazard.

I purchased the Centennial Commercial Technology washer in June of 2013. In the last 2 1/2 years it has been repaired 3 times. The transmission had to be replaced twice. My household consist of two adults and definitely it is not overused or overloaded. The washer currently is not working. Consumer service cannot schedule an appointment for repair for 2 weeks. Previous repairs took approximately 2 weeks to schedule a service appointment and it took another week to two weeks to get the part in and washer repaired. I have decided to consider this an expensive learning experience and will not purchase Maytag products in the future!

Maytag Dishwasher model #MDB7759SAW3 continues the Whirlpool company legacy of subpar control panels in all of their dishwashers. It is telling that they have been allowed to market the exact same failing parts for well over a decade without any accountability. They had one recall circa 2007-2010 and pushed customers into purchasing the model I have which suffers from the exact same control panel design.To further frustrate the consumer experience, Maytag customer service reps and supervisors allege that they have never heard of a customer having issues with their dishwasher control panel before. The panel beeps endlessly and refuses user input regardless of whether the door is opened or closed. After a power disconnect it will reset and sometimes allow one load to be washed before resuming the non stop beeping. If opened and closed during the beeping it will cycle through a completely new wash cycle on its own and resume beeping. Maytag customer service response this morning was, “thank you for being a Maytag customer”.We will my be purchasing their replacement control panels as they are of poor quality and it is well documented that the new ones fail annually as well. These are “high end” appliances and are not inexpensive. We will simply cease to use whirlpool, Maytag, Kenmore, Kitchenaid, etc. brands in our home and will advise everyone we know to protect themselves the same way.

We have had our side by side Kenmore for years and it hasnt let us down! We eat mostly fresh food since we cook a lot and we always have plenty of space for our food. We are only a family of 2 though. They say the ice maker is the first to fail and it has not given us any issues for nearly 10 years now! Love Kenmore!

I have a top load commercial tech washer with an agitator that is brand new as of September 2019. I have done all of the troubleshooting suggestions and nothing works. I use 1 tsp of liquid cold water detergent, deep fill, extra rinse, and clear liquid oxi and my darks still come out with white stains. I have had a Maytag tech check out the machine and it checks out without issues. I would never recommend this product to anyone!

Bravo XL Washer & Dryer - I have owned this set for just over 90 days and have called Maytag several times just to get insulted. The customer service representative is not helpful at all, and tells me that I am not using HE detergent or that I am using too much HE detergent. Furthermore, they tell me that if a service technician comes to my home and nothing is wrong that I will get charged. So much for the extended warranty and what is wrote on the Maytag site. I explain each time that I am using name brand HE detergent and the recommended amount. The soap dispenser in the machine provides a fill line that I fill to. I have even tried using less detergent as recommended by the appliance store that I purchased the machine from, and still the washer does not clean my laundry and leaves residue on everything. I have even tried using the extra rinse, and extra heavy soil setting which does not make a difference at all.The other concern is that the clean washer feature light flashes weekly. I have purchased the cleaning tabs recommended to clean the machine, and run this clean cycle every time the light comes on. The dryer does not work all that well either and shuts off before the laundry is dry. Sometimes the dryer will show an error of airflow restriction or low airflow. This is confusing because the dryer vent and hose are clean, and the lint filter is also clean. This is so disappointing because I thought Maytag had great products. However, as I read other reviews about these machines and the customer service representatives it seems that there is a systemic problem with the machines and the customer service representatives that needs to be addressed by the leadership at Maytag.

We purchased this model from Home Depot in February 2011. In July 2011, I found it full of water and dirty dishes after running a wash cycle. It was completely dead like it wasnt getting any power. I checked the fuses, etc. - nothing was wrong that I could find with the power supply. I called for a service tech that day and they sent someone out to check it. It was the control panel. They shipped me a new control panel and the tech came back to replace it under warranty. It worked great until July 2013. Again, it is full of water and dirty dishes, wont turn on and has no lights on the front panel. I called Maytag to get a service tech. The warranty is expired of course. They offered to sell me a replacement dishwasher at a discount for $409, Model # MDB7749SBW. Or I can buy an additional 1 year of warranty for $269. I also could buy a control board for about $150 online. None of these options is attractive right now, but hopefully if I get the new model, it will not have any issues... I wish they would just tell me it was a crap unit instead of giving me the option to either get a new one or pay for a useless warranty. I am fed up with this dishwasher. 2 control boards in 2 1/2 years is unacceptable and indicative of a defective unit or design. After reading the reviews here it appears to be a defective design.

The right front heating element works at the high position only. The over doors viewing glass is too fragile. It shattered while positioning the range. Otherwise, there are no other issues with electric range.

This is a continuing aggravation! On July 27, I discovered the dishwasher (MDB7600AWW) tub had developed a crack in the bottom right rear and had warped my countertop and the floor under it was full of water! I called the appliance store where it was purchased and was told to call Maytag. I have a 20-year warranty on the tub with free replacement of the unit if it fails. I called Maytag and was told we needed a service call to verify. I scheduled it for July 30, and 3 minutes and $75 later, yup, tub is cracked. Its a known problem, and the dealer has already replaced some for customers. I called Maytag to get the ball rolling for replacement. I spoke with Jennifer and was told shed get back to me.Meanwhile, we went to several stores, checking out other Maytag models. So, Id have some idea of what was available as a replacement. I called Jennifer on July 31 with a suggested model Id find as a suitable replacement. She said shed check and get back to me. On August 13, I called Jennifer for some answers, got the voicemail, and left a message. On August 14, I went online to chat. Finally, I was told Id have a replacement in 10-12 days. Id be contacted to schedule installation. On August 16, I called a local dealer again. He cant understand the problem. Hed replaced two others in a few days. He made some calls for us and gave us the name and phone for the company replacing the dishwasher as well as the work order. Installation was tentative for August 23. (Hed been cut out completely!)I called Optimus Solutions, and theyre awaiting shipment. Tentative installation was on August 23. On August 22, theres still no word. I called Maytag customer service. Sorry, it was shipped to the wrong address, so it was shipped back! Its now in transit and supposed to be delivered to Optimus Solutions today but not being scheduled for installation until August 31!This has become one nightmare after another with everyone pointing the finger at the next guy. Phone calls get only the same runaround. No, speaking to a supervisor wont help - theyll tell me the same thing. Isnt that convenient! Meanwhile, Im still washing dishes by hand and having psoriasis on my hands, which are like two pieces of raw meat right now. It is beyond aggravation; its bordering on torture! (No, I cant wear gloves. They make my hands sweat and even more sore!) Besides, I shouldnt be washing dishes by hand. I paid for a dishwasher that failed through no fault of my own, and now, Im being punished for purchasing it. I can guarantee that if I had no warranty and had to replace this dishwasher, it would have been replaced immediately!Never again. I purchased all Maytag products for my new home. As they fail, I can guarantee I will not be replacing them with Maytag or Whirlpool, which now owns Maytag. I will be telling everyone who will listen to stay away from Whirlpool and Maytag, because their customer service sucks big time.

This is beyond one of the most disappointing purchases I have ever made! It has been about 15 months since purchasing this dishwasher, and as of today it is not working! Blinking start button. I see from the hundreds of disappointed customer comments that I am not alone. With this many people complaining of the same issue, that Maytag should have a recall... I paid about $550. I get that quality does not supersede the almighty dollar, but come on!

This dishwasher is reliable and has NEVER had any repairs. It cleans fairly well, but I do wash off dishes before I put them in. The one complaint I have is sometimes the dishes smell funny after washing. I think it may be our water though. I also like that there is room for oversize dishes and glasses on some of the racks. Overall, I would buy it again.

We paid for a brand new washer and dryer from Maytag/Whirlpool. Right on the machines it has stamped in a metal plate 10 year warranty. So at 4 years when my washer started screeching and smoking I called for service. Yes, there had been a leak that burned out something in the engine and the bearings were shot etc etc. But they have been back 3 times. Each time they lack some part. I first called them on July 29, 2020. Today is October 13, 2020. They have still not got the washer repaired. I need to do wash every day. We are a family. We also have a senior in her 80s. And dogs. I need to do wash every day. So for weeks I went to the laundromat. That cost a fortune. Then a couple of weeks ago I impulse bought a new washing machine. A Samsung. On sale. Doesnt match the Maytag dryer. And the old washing machine got moved out to the garage. Its the pandemic. I cant keep going to the laundromat. What good is a warranty if Maytag/Whirlpool always has excuses for why they dont have parts. Its the motor. The very basis of the machine. It took them 2 weeks just to look for one. You wouldnt believe the excuses they make when we talk. But I am really unhappy with the way it all worked out. What good is a repaired machine 3 months later than I needed it. I had to buy a new machine. Why didnt they just tell me to do that on day 1 so I could avoid the laundromat. Why are they spending so much money to basically repair everything in that washer when they could have just bought me the new machine. When is a warranty not a warranty at all, but just a big lie?

Purchased this maytag oven from home depot November 2011. Oven has been working properly since install. The top burner controls do operate too easy and you can just brush up against the stove and turn the gas on which I seen here was mentioned. My major issue is the stainless steel finish that was applied. It appears that this metal was not properly prepared prior to applying the finish. The oven door is with rust blisters. The metal under the coating is causing this problem. The finish in the other areas is with no problems... No chemicals have been used to clean this oven.Customer service of maytag stated that this stove only has a one year warranty... so if you buy any maytag just remember one year and when it breaks down the cost to fix will be more than a new defective maytag stove. I will not purchase another maytag product and I do not recommend that this manufacturer be considered when purchasing any appliance.

I made the mistake of buying a Maytag 2 years ago, this machine would not wash clothes even when using the deep water wash. I should have looked at it closer, it is so full of modern computer garbage that I was having to wash clothes twice so the water saving was negative. I own a business across from a major shopping center so what we did was we loaded it up in one of our trucks and parked it in front of our business with a giant sign and invited people to take a look before buying one. In 6 months we must have had at least a 1000 people inquire.

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

Purchased a Maytag fridge in August of 2010. Had issues January 2014 - needed a new circuit board. At the happy cost $230.00. Well it is now May 2014 and had to have the repair man here again for another circuit board $258.64. Maytag will not stand behind their product or parts they use in their products. They flat out told us that we shouldnt have to replace the circuit board that often and then said they wont stand behind it. So buyer beware. DO NOT BUY ANYTHING MAYTAG!!!!!

I bought a Maytag 4452BDW stove, the more button is not working. I did my research and was not happy to see this is a common and reoccurring issue with Maytag Stoves. The expensive of the part that too often fails again along with the cost of the service man to repair it places the Maytag as low quality at a high price. I am hoping to see a company that stands behind its product by addressing this correctly and promptly. It would be a pleasure to have my faith restored as it should be by Maytag.

I have been Maytag customers for 40+ years. I purchased a new Maytag washer and dryer at Home Depot last year. The paint is coming off and the top is starting to rust. We have had Maytag washers and dryers for as much as 17 years that did not rust. The reason we bought Maytag was quality. Rusting in one year is not quality. Please contact us ASAP. Home Depot said there was nothing they could do.

Consider all other manufacturers before purchasing a Maytag dishwasher. Our 3 year old model MDB8949SBB1 is junk. The control panel is a joke. Works when it wants to. Do not spend your hard earned money on Maytag.

This range cooks evenly, producing satisfying results every time. It’s easy to use, simple to clean and serves me well daily. It has a double oven feature with a smaller oven on top which is not only convenient but energy-saving. The top features a cooktop which is easy to use and maintain. Never had a better cooking appliance!

I positively HATE the new BravosXL Maytag washer, which has no decent agitator. It is ruining my clothes, as it spins with little water and leaves soap residue all over the clothes. Additionally it puts large, long wrinkles in my knits, especially disfiguring slacks. Maytag must have known how rough and ruinous this washer was on knits BEFORE selling it to an unsuspecting public! I want my money back in order to purchase an old-style, well-functioning agitator washing machine.A class-action suit should be brought against Maytag. There was no way to know before buying and using that this machine is horrible!!!

I purchased a Maytag Bravo washing machine item # 26 23872 for $617.69 on 11-23-11 and it was delivered and set up on 12-02-11. My problem is if you have dirty sweaty clothes, you cannot get them clean with such little water. I used the HE detergent as directed. I talked to a woman at the local Sears Appliance store this morning, 7-11-12, about it. She said I need to use Affresh. So I did clean my washer but with a similar brand and my clothes are still stinky. I have even washed an empty load or two with bleach and hot water. I make sure I wash with hot water and completely dry my clothes.When you take a bath and dry yourself off with a towel, it smells like a musty basement. I am allergic to mold. I cant even take a wash cloth, get it wet and wash my face without wanting to throw up from the smell. I have had guest comment on the towels as well. Its embarrassing. The problem is you cannot clean something with an inch of water in the machine. I am 58 years old and now have to do the wash. I went to the store and asked if we could return it for an exchange or anything like a discount on a new one and she would not budge. She said it had to be within 90 days but 90 days was in the middle of winter and I was not having dirty sweaty clothes from doing outdoor yard work.Now that summer is here, 7 months later, my clothes have been smelly for a few months. I cant take it anymore. I showed the woman that I had been to Lowes and had an estimate of 10% off with free delivery, set up and haul away. She said she could do 15% but when you add on the delivery fee, it was higher than Lowes. I purchased my whole upgraded kitchen stainless steel appliances for about $7,000 and this set of washer/dryer but Sears could not help me out? What a disappointment that a loyal customer such as me could not at least get free delivery on a new washer. I went right back to Lowes and ordered the same machine I wanted Sears to sell me matching Lowes price.So now, I am stuck with a 7- to 8-month-old machine still in the one year warranty that is like new but is a worthless piece of junk as my clothes all stink. Run, dont walk if someone tries to sell you a low water HE machine. I tried sending this letter to searsinfo.com corporate office and it is rejected even though the website gives you that address.

Discovered that thousands of others are having problems with the control panel on their dishwasher. Mine is Model # MDB7749SBM2. Looks as if I should just junk this horrible product and buy a new one (another brand, of course). My biggest concern is that I purchased other Maytag products along with this dishwasher, ie, a refrigerator-freezer, a built-in stove top/oven and a microwave. I have had a service call on the fridge (water line), the oven (gas) will indicate a set temperature (400 degrees for example) sometimes it will only be abt 200 degrees via a portable thermometer... Sometimes it doesnt ignite at all (have to reset it 3 or 4 times, the microwave has issues with the digital readouts, and on and on and on.I have only had these appliances about two years (after warranty expired) when each unit started exhibiting problems. I paid $175 for the fridge repair and am now considering biting the bullet & replacing everything as MAYTAG/WHIRLPOOL apparently isnt going to take responsibility for any defect on ANY OF THEIR PRODUCTS! Im 75 years of age, retired and cannot afford the replacement route but it looks like I dont have a choice unless someone has a better suggestion. I dont have the skills or energy to attempt the repairs myself.

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

At first the Maytag Bravos XL top load washing machine met all me expectations. After 3 yrs. the top where you load bleach and fabric softener began to rust. This is not covered under warranty. My last washer was a Whirlpool and had it 15 year and never had that issue. So it cant be from the water, just poor workmanship. Very disappointed. Now my lid came loose and is ready to fall off. Would not recommend.

I purchased the Maytag double-oven gas range, Model MGT8775XS, in 2013. The quality of this double-oven stove cannot be understated. Performance? Terrible. Reliability? Awful. My experience was shocking because when I was a kid, Maytag was the ideal for quality and reliability. Those days are over. When delivered in 2013, the ovens did not work. Heating went to 200 degrees and stopped. During the next three years, we had this Maytag stove repaired four times. The most recent repair was in October 2016. A new regulator and igniter cost us $360. Four weeks later you guessed it the ovens stopped working yet again. We sent the Maytag stove to the recycle dump. Its far more valuable as scrap metal.

I purchased a Maytag refrigerator 4.3 years ago. Model #NSD2572VEW01 side-by-side. Came home to find water on floor. Called for service at a local company. Tried several new parts, only to find out I had a bad compressor. Part cost $358.30 + labor charge which couldnt be estimated because of difficulty with installation. Called Maytag for help, was told FIVE times, Sorry, nothing we can do to help you. Have never had any other appliance in my life except Maytag. NEVER had a problem with anything before. Have washer, dryer, fridge, stove, microwave, and dishwasher. Found the answer to be unacceptable!!!

I have had nothing except trouble with my new Maytag Bravos washer! I first had a suspension arm or something like that replaced along with the agitator. My water cycle has never worked correctly since it was new. I take out the clothes and half are still dry. My daughter washed her kids’ clothes in the washer while she was living with us and the stains did not come out. She thought that is really unusual since they werent stains that normally you would see left on the clothes. I went to my father-in-law’s house (they have a front loading Bosch), took her detergent with her that she used here and guess what? It’s just one washing and the stain was gone. She had washed the clothes in our washer at least 7 times trying to get out the stain. Now, we have such a loud noise that it sounds like it is going to take off. Then, the bottom of the washer started to leak. We took it out and checked it and we cant find the leak. The clothes smell awful when they come out of the wash. I dont know if it is bacteria build up. I use the cycle cleaner when I am supposed to. This is so sad. This is the first time I have had matching washer and dryer and I wish I would have kept my old Sears model that worked great. I havent decided if we want to fix it. With the price to fix it, I can buy one I might like. Never will I buy Maytag again or another Whirlpool without checking out the reports.

We bought a new Maytag dishwasher MDB7609 as part of the 2010 recall. Within the first twelve months the black skirt at the bottom of the door collapsed to the floor. It was in small pieces and brittle as though exposed to excess heat. The repairman fixed it free but made the point it was not covered under warranty. Next the heated dry cycle baked the water onto the dishes forming a white crusty layer. We have a water softener that works very well. We stopped using heated dry because it is too hot. Last night before bed, I was standing in the kitchen and I smelled something burning. My wife had mistakenly programmed heated dry into the cycle. Obviously this dishwasher is as much a fire hazard as the one it replaced but no recall has been issued yet.

I purchased a washer on 8/13/12. I had it installed on 8/20/12. It did not clean clothes properly. I went to Two Guys and they said they dont take returns and told me to call Maytag. I called Maytag and they sent a a service agent to check the machine on 9/10/12. They said the machine codes were imbalanced and over stud. They need to recalibrate the machine. I did laundry the same day and still find clothes do not come clean. I need to return the machine. I called Maytag and was told they dont take returns. This machine is not cleaning clothes as it should be and I want a refund!

A contractor purchased the Maytag MDB7609AWW2 dishwasher about two years ago. Sometimes it will start a load, but most times it will not. The light for high temp, heated dry and sanitize work, but the heavy, normal, light indicators will not light up. Im faced with either replacing the control board or control electronics. I was told Maytag is a quality product. I have not abused the product. The last dishwasher that I had lasted 10 years. I only purchased this one because of a remodel. I will most likely replace the control board since thats the defective part. It doesnt give me a good feeling about replacing the part since it’s obviously a defective part. I will consult Consumer Reports before purchasing another dishwasher.

Maytag Bravos Automatic Washer 300 - I purchased this washer on July 29, 2010 from HH Gregg. It is less than 3 years old. The washer stopped mid-cycle, did not drain, and displayed the code Ld. The service company recommended by Maytag said that the control panel is defective, and the cost to repair/replace it is over $550 and isnt worth fixing since, he says, these washers are notorious for having problems. Maytag is unwilling to recall this washer despite all of the problems that have been reported. They are unwilling to even admit there is a problem.

The only complaint is the lights on the bottom quit working about a month after we purchased. It was nice to light up the stovetop when cooking. Now it’s slightly dark. I have gotten used to this. We spent about $8000 on all the matching Maytag appliances we purchased. I would love to replace all but not in the budget. I am a dissatisfied Maytag customer.

Purchased washer in 2015, worked pretty good for 4 years. In 2019 belt, support rods, and control board replaced. In 2020 clutch, pulleys, and suspension replaced, waiting for service technician to replace transmission later this week. I purchased extended warranty thru Lowes, glad I did as the machine literally jumps in the air during spin cycle. Lowes stated I needed 4 repair visits to place a claim for replacement! Machine will not spin properly on high speed. Luckily I have a spare machine in the garage to use while I waited for repairs to be made. However, nothing seems to be correcting the problem. Very disappointed in the Maytag washer.

I bought this washer about 6 months ago and I seem to get clothes that just arent clean and have marks on my dress pants and my whites are awfully dingy. Never have I ever had white things that didnt stay white. I honestly would never buy this type of washer again. I am actually hoping that there is a way to at least change the water level. Also I hate the fact that I cant add bleach to the water before the clothes and to let the bin fill and mix correctly. I dont think the bleach even gets to the clothes.

This washing machine has been very reliable.No repairs needed yet. This machine has stood the test of time. We use it at least.. four times a week. Light and heavy loads. It fits in our washroom and budget. Just perfect. I would recommend this brand to everyone.

I bought the top of the line Maytag washer. I was told they have improved their washer so that it no longer requires an agitator. I was also told the new machine saves you money by using less water. It has a sensor so that it only puts the water needed to clean your clothes. Instead of filling up with water and having the agitator to stir the clothes around, this new and improved machine puts a small amount of water in the machine and vibrates. The end result? All of the dirt and debris gathers in small pockets and sticks to your clothes. In order to save water the sensor only allows a small amount of water to enter the machine to rinse your clothes. When you consider how many times you have to go back and rinse your clothes before you get the caked on dirt off of your clothes, its costing you more money, more time and more aggravation. Oh yea, the maintenance man was out three times before the machine was a year old. The last visit was to replace that fine Maytag motor that was less than a year old. I have pictures that show my clothes with caked on dirt and debris on them after they have completed their wash cycle. It is HORRIBLE!!!

We purchased our Maytag washer and dryer 5 years ago... THE ABSOLUTE WORSE PURCHASE... on average 3 repairs a year after the first 6 months!!! Now the dryer is down. It takes minimum 2 trips out from a repair company to fix even minor issues. We are going to Sears today to replace both units. PLEASE SAVE YOURSELF A HEADACHE AND DO NOT PURCHASE A MAYTAG! Yard Sales next step for our... cheap.

I recently bought a home that had a Maytag Neptune set. While they were newer than mine, I sold my Kenmore set, dirt cheap. Last night when I opened the washer door to take the load out, smoke billowed out. Im sick about this. There should be a recall on these washers!

I bought a Maytag dishwasher in January 2013. Three months later, the cheap plastic latch on the door malfunctioned. I waited 3 weeks for the repairmen to get the part in. Is there a sense of urgency anymore? If I owed Maytag money, I bet there would be a real sense of urgency on their part. Next time it will be an LG dishwasher.

We purchased the Maytag MDB8959SAS0 dishwasher about 2.5 years ago. A couple of days ago, the lights on the control panel started blinking and beeping erratically. I contacted Maytag and they said the control board likely needs to be replaced to the tune of around $250, not including labor! We spent $800 on this dishwasher and it cant even last 3 years?? Ridiculous. The only other advice the service rep. had was that we should have bought the extended warranty. Gee, thanks. I guess with Maytag, you really DO need that extended warranty because their products are junk. I think I will just scrap this dishwasher and go with a Bosch. We also have a Maytag range that needed servicing after owning it for only 18 mos. And a Maytag dryer that needed servicing after a month (at least that was under warranty). I will NEVER buy a Maytag product again... they are complete junk.

I purchased a Maytag Bravo HE washer and dryer! The biggest mistake I ever made! Three inches of water is max for a load of clothes! This is max full or actually empty. The washer was a third full of clothes and only the bottom layer was wet when it went into rinse! After pulling a calf I really wanted the top pants washed. Nope. Went in dirty and dry to the rinse cycle to spread the bacteria throughout the load. The soap was still laying on the dry clothes on top. Repair guy spent two hours and couldnt get enough water to at least dampen all the clothes in the wash cycle. I would like to see how much cow afterbirth bacteria was still in clothes. I didnt buy a machine to dry wash my clothes! I have asked for my money back on the pair through the performance warranty. Well see! I am not giving it a star as it doesnt earn one!

I live in Southern Indiana and bought my appliance from Charlie Wilsons for 25 years. 3 years ago my Whirlpool washer quit filling up to full level. I decided to move it over and use for my car and pet towels. When I bought my hose in March 1999 every appliance was Whirlpool washer, dryer, refrigerator, stove, dishwasher. GE is made in Louisville, KY but I dislike the union.Anyway I bought a Maytag model MVWC415EW1 June 2017. Recently it started making a grinding noise when going in spin cycle, wadding cloths up and leaking black water on basement floor. Called repair shop out. I just do not have the time to repair stuff anymore. They came out $80.00 service call and tell me at least $300.00 to repair. Wait a minute. $500.00 to buy a new one over $300.00 to repair. Guess what I did? I called Maytag and complained. CASE NUMBER **. They reviewed and denied. Not a problem. I said, I guess you do not need me as a customer anymore.I have twenty year old Whirlpool washer and dryer still running, I have replaced my refrigerator (Old one in garage still running a colder than new fridge and day of the week). Bought Amana=Whirlpool and it has quit and replaced with a Whirlpool July 2019. Nothing is built like it used to be BUT we still pay as much if not more. Off I go to Charlie Wilsons to buy a $1000.00 Speed Queen washer with 7 years parts and labor warranty. Had to order it but old washer still running just not going to full mark.

Bought this as W/D set brand new from Home Depot. Had been noticing incredible wear and tear on clothes, as things get so tangled up and need to be practically ripped apart before going into dryer. Cycle times are crazy long, up to over an hour in some cases. Doesn’t have a “Speed Wash” cycle. But WORST of all, after less than 3 years, it just stopped draining properly. Tried all the Codes test, etc. Finally called a repairman just to be told repair costs would probably cost more than the machine is worth. $125 to be told we ought to just buy a new washer. Not happy.

I cant warn you enough NOT to buy this design flawed machine. Ive only owned mine two months from Home Depot, the install was a nightmare and now due to a poor design flaw, if you miss loose coins or anything in pockets it will get trapped between the drum and the tub causing rattling and noise during spin cycle. Guess what? Service calls EACH time this happens. This is nothing more than a $750 piece of junk. I feel like its marring the whole feel of my new house. I hate hate hate this washer and am trying to get Home Depot to take it back, Maytag to refund me or sell it at a huge loss. This is NOT getting anything you pay for and I vow to NEVER EVER buy Maytag again.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

I bought a Maytag Neptune top load washer in 2002. It worked fine (with the exception of smelly clothes) until October 2011. Since then I tried replacing two new clutch assemblies, a new outer tub and bearings. What we were just told this week: it needs a new spinner. Finally throwing in the towel and taking the $500 credit from Sears and buying a new washer. And I can guarantee I will never buy another Maytag product again!

I purchased a Maytag refrigerator, stove, dishwasher and microwave in 2006. Like another commenter, I also insisted on all Maytag appliances. What a huge disappointment. About four months into owning the microwave, a computer module had to be replaced. The microwave stopped working about six weeks out of warranty. It just stopped working, period. I was told by Maytag that they consider microwave a disposable product and they would not cover the repairs. It was cheaper to buy a new one than repair the old one so I replaced it with another brand. The dishwasher failed after 4.5 years (would not drain) and again it was cheaper to replace it than fix it. The oven range handle broke off (normal use) in August 2011 and that cost me approximately $200 for the part and the service call. The refrigerator has had two service calls for the ice maker to replace the motor. The first was covered by Maytag, the second by me. This occurred when the unit was approximately three years old. In August 2011, I had another $90 repair because the ice maker drain (?) was plugged and had to be cleared fixed. I have never been able to pay what I paid for these appliances. Prior to this, we always purchased a middle-range appliance and we never had problems like this.I will never purchase another Maytag product again. This is so disappointing. I live in MI and I wanted to support a MI business. Unfortunately, I wont be able to help out this particular company any longer. Dont buy Maytag appliances. It is a waste of money.

Just like so many others, our Maytag 300 Quiet Series, just 2 years old, has a malfunctioning control panel. Repairman told us this has been an ongoing problem with Maytag dishwashers. Steam/water gets into the control panel.For a while it worked on and off and now it is dead. I am saving up to do the repair, but in the meantime the dishwasher sits idle.

We bought this brand new washing machine just 6 years ago. Went with a Maytag because they are supposed to “last forever”. Ha! Last weekend it stopped spinning. Water would drain but no spin cycle. Had a recommended repair person come out and he said it was unfixable. The bearings were shot. This is crazy. There are only two of us using this machine how could it be totally unfixable 6 after only 6 years. The average washing machine life is supposed to be 14 years. No more Maytag for us.

I wish I had read these reviews before purchasing my dishwasher. I have used it 40 times max. The control board went out. They want 307.00 to fix it. Really? Why would I fix this piece of crap when I can buy a cheap one for that price that would work better. Ridiculous! I paid good money for this dishwasher and the warranty that comes with this is a joke. Save your money and brand from a company that stands behind their product.

Our front load washer is two weeks past the one year warranty and need $650 in repairs! I will never purchase a Maytag product again. My last Maytag was 19 years old when we got this new front loader for energy efficiency. You dont save money when you have to replace it after one year.

My husband and I purchased our Bravo washer and dryer from Home Depot about 5 years ago. They have been the worst ever. Clothes always tear and we continue to receive an F1 error every time we try to wash something. I dont have the money to buy a new one, but I sure wish I did. I will never buy a Maytag anything ever!

Just purchased a maytag dishwasher from home depot. I did the install myself. The dishwasher will not work at all the panel lights up, but no water goes into the washer. I now must wait two days for repair. After reading all the other reviews, I am thinking about returning it for another brand. And yes the water supply is on. I have hooked up several dishwashers. This is the first time a brand new one did not work right from the store.

Had the washer for less than 3 months just a week before the 90 warranty was up and it stopped spinning. Called service dept. What a joke for this company that keep yessing you. Took a week before someone came out. Said washer needed a new motherboard and they would only cover it once but there seems to be a ongoing issue with their motherboard. Had to wait over 2 1/2 weeks before they would have one in stock. The tech installed it however now when it spins seems she left the top loose.

We bought a new Maytag fridge in 2013, french doors, ice maker on the bottom. In 2 years we have replaced the control panel on the front door 3 times. Each time the plastic panel cracks and breaks free. The last time they replaced the entire door, all on warranty. Well 3 months later it does the exact same thing. I call Maytag and they say, fridge is past its warranty period so no coverage. It will cost me about $600 to replace this control panel.

We bought the Maytag Washer and Dryer set about two years ago from Home Depot. We have had to have the washer repaired several times in that two years, most recently for a cracked mother board controller unit. The same day we had to have the washer repaired, we also had to have the dryer repaired. Lint and dust is not properly filtered out by the filter and accumulates inside the dryer where it should not be, up against the gas heating unit. The repairman indicated that it was badly scorched and that we were lucky it had not caught on fire. Another customer of his had the same unit, which burst into flames one day when she had left the house with the dryer going, causing a house fire. The quality of these items is highly questionable. Having to spend nearly $600 to replace a cracked mother board only two years after purchase simply is unacceptable.

Recently started having puddles of water on floor every morning. Just noticed a thick sheet of ice on freezer floor when I had trouble closing the freezer door. Also the water dispenses very slowly. Removed filter and it would not dispense at all. Will try melting the sheet of ice to see if that helps. Purchased 2011.

Maytag Bravos XL he Washing Machine - Having owned several Maytag washers in the past, I thought this would be perfect, instead, it is the worst washing machine I have ever had. This machine does not clean well at all, spots on clothes stay put. I have tried different amounts of HE detergent and clothes are twisted and wrinkled terribly and have remaining soap residue on them, even when I use less soap than recommended. I wish I would have returned this machine immediately after a few loads. It doesnt get better with time. It is very loud, but that is the least of its problems.

Purchased a new Maytag washer and dryer in November 2015 after having a old set not Maytag for 25 years with no repairs. WOW. Then the new washer went out in Feb. 2016, now the dryer in May 2016. Very unhappy. Is it because the machines are now made in Mexico? Cheap labor and cheap parts. ICK!!! Thank god for the extended warranty.

We ordered a new Bravos washer and dryer at the end of November but due to delivery snafus, we did not have both until the second week of December. Just yesterday, both failed. Part of the drum on the washer ripped off, and the dryer just stopped running an hour later. I am used to getting a long life out of appliances. The old dryer was over 20 years old, and while the old washer was only 17 years old, I thought it would be nice to get a matched set.

Maytag has always been my choice with appliances. Ive purchased others and always dissatisfied. This dishwasher has been a trooper and lasted forever. Its been overworked with 4+ children and yet still going strong. I recommend Maytag????

Bought a new Maxima washer in January. Worked for one week. Got error codes and electronics board shut down. Contract serviceman says board should have reset after turning off. Ordered new board and it is missing one of the electrical wire connector plugins. Maytag/Whirlpool is having a problem with these boards.Three weeks without a washer. Two days off work. When it goes out again, days off work will be close to what I paid for it. Thinking I may cut my future losses and buy another brand when in-transit board goes out.

Purchased Maytag Centennial Washer and Dryer (MODEL MVC300VWI) at Home Depot 3 yrs ago. After 6 months, washer started to rust. Maytag told us It was not their problem. A 6-month old washer should not rust! Poor quality + poor customer service. Dont buy!

We have only had this Maytag Washer for 3 1/2 years and the bearings went out. There is just my husband and I in the household and we are retired. We only use the washer once or twice a week. The repairman said the whole tub (inner/outer) would also have to be replaced. We paid $1,126.03 for the machine and it will cost $700 to repair it. Needless to say we will not repair it but will buy another washer. We have always been satisfied with Maytag appliances until now. We probably will not buy another Maytag appliance due to this event.

Bravos XL washer- This is probably the worst purchase I have ever made, first off, at $1000 it was a pricey purchase however, I chalked it up to it will last many years without issue. After only 3 years, the unit leaked water and was so loud you couldnt stay indoors while it was on spin cycle. The bearings and seal were completely shot and needed replacement, after the sticker shock of having a good repairman fix the problem I decided to tackle the job myself. (Thank you YouTube). All was well for the next 2 years until it all happened again. Maytag is junk and will never get another dollar from me-ever! A Speed Queen TR5 now sits where that piece of crap used to reside. BUYER BEWARE!

I purchased a Maytag Neptune Washer and Dryer at Home Depot for over $900. Within months, the board went out. The repairman said that they didnt even know how to fix it yet - no training. The board was out again. This time, it was not under warranty. The repair costs $779 including part and labor. There were numerous other little problems along the way that we did repair, but now, forget it.

I am extremely dissatisfied with the Maytag Gas stove and oven. The setting are too high and you cannot simmer something, it burns. I tried the oven cleaner and my oven is still dirty. The burner knobs do not have a click feature. I came home to a house filled with gas. I was not using the top burners, so I must have brushed up against the burner knob while using the oven. I was only gone an hour, imagine if I had been gone longer and walked in the door and created a spark on the rug.

I purchased a Bravo washer and dryer set about a 2 1/2 years ago and had problems from the start. The dryer control panel went out the first day. No problem, they replace the panel. The washer is a different story. The agitator went out next and the wait time to repair it - 3 WEEKS. The agitator went out again for the second time and the tech stated that it had to be replace. Wait for it. Waiting time - 1 month including parts. To make this story short the agitator will go out every 4 months and the tech stated once its been replace it will work like a new washer. Wait for it. The agitator has been going out ever since and the wait time average 3 WEEKS. Wait for it. This Maytag is trash.

After 2 years and 1 month, the machine stopped spinning the clothes on any of the cycles. After attempting to use the spin cycle manually that stopped working. I called Maytag, my washer is out of warranty. After discussing the situation with knowledgeable appliance people, they said it is probably the motherboard. I know how expensive that is to repair and pay for a repairman to diagnosis the problem. I decided to purchase a new washer. Of course, it was not a Maytag. I read online all the people with same or similar problems left out of luck. This is an outrage and Maytag should not be allowed to get away with producing, selling and not standing behind the products. These machines should have been recalled and replaced with ones that are upstanding and will last for more than 2 years.

Have had Maytag HE washer for 4yrs, so far it has broke down three times. I contacted Maytag and they asked if I had bought extended service contract? No I paid $700.00 for this washer and had expected it to work a little longer than 2yrs before seal in door is cracked. Would NEVER buy another HE or Maytag product again!

My refrigerator is a lemon! We bought a Maytag bottom freezer French door refrigerator model #MFD2561HEW in May of 2007. Less than a year later, it stopped working and ruined all the food inside. I cant remember the problem that time, but it was fixed by Maytag and we were reimbursed for a portion of the food we lost. Two years later, the temperature got warm in the refrigerator and freezer sections, and we were gone for a couple of days, so when we got home, all of our food was spoiled. This time we had an extended warranty in effect and they replaced a circuit board, but we were out the food. A few months later, the same thing happened. This time we were home and saved most of the food. The compressor was replaced, again under warranty, but it took 2 weeks to get the part. Now, less than a year later, the freezer and refrigerator compartments are getting too warm and frost is forming in the back of the freezer. When it finally does get cool, it freezes the food in the refrigerator section. It also makes loud bumping sounds. I paid $80 to a repairman today to tell me that theres nothing wrong with it, thats just the way it runs! He suggested I put a gallon of milk jugs filled with water in the freezer to hold the temperature when it starts to rise! This piece of junk is just 5 years old! When I complained, I was told to call Maytag and discuss it with them. This refrigerator was not cheap and I see that many others have had similar problems. How do they get away with selling an inferior product?

Maytag Bravos XL MVWB980BGO. To start, I live on an acreage so some problems may be related to being on well water. The most annoying part is the washer doesn’t have a drain & spin without rinse. So, when my well pump started acting up, I had no way to just drain & spin off the load, so I had to try to lift thoroughly soaked clothes and try to dry them...which took about four hours. Another aspect that is a pain is uneven loads. It keeps trying to fill, instead of just stopping & letting me adjust the load myself. Then the damn thing won’t reset. I often have to resort to unplugging the machine and starting over. High efficiency is a joke. I’ve had the machine about five years now and it goes low flow error, even though the flow is fine. I’ve tried running cleaners through the water line and it’s still doing the same thing. The only thing left to try is take the machine out and try and manually go through the lines. For the amount of money we spent on this machine, I am thoroughly disgusted with how it runs. It is the first & last Maytag washer that I will ever buy. Next time, I’m buying as cheap & basic a machine as I can buy. On the upside, the dryer works perfectly.

It leaves white stuff all over everything. You have to rewash or rinse black clothes at least twice. We have to clean the washer frequently or the clothes smell like mildew. I chose Maytag because I thought they were the best. Apparently, I was wrong and it was a mistake buying this.

Maytag top loader washing machine - Worst appliance purchase ever made. Does not clean laundry, takes all day to do 5 or 6 loads. Not enough water to properly wash or rinse load, even using the deep water setting (a joke). A load of 2 king size sheets and 4 pillow cases wadded up in a ball and rattled around so hard in the spin cycle, it pulled the plug out of the wall. Maytag sent out technician who conducted diagnostic testing, which did not include any actual laundry. Technician said machine was operating as intended and verified I was using the machine properly. I have tried to return this machine since the first load was done and realized it was a disaster. Maytag refused to help. In fact, their phone agent had the audacity to suggest I wash one sheet at a time to prevent the machine from moving across the floor so far the plug came out of the wall. Maytag surely is not what it used to be. Im sorry I did not know they, like so many other companies, dont care about their reputation or customer service, not to mention producing a quality product. I would say they are actually misleading their customers by calling this product a washing machine.

I am not complaining at all about my dealer. I am complaining that I also am like the many others with the French door fridge/freezer. The bottom of the freezer freezes up and water pours all over the floor. I thought that Maytag was a good appliance, but also had problems with the pump and drain on my washer. Both of these are only 2 1/2 years old.

The control panel and the electronic control box had to be replaced after only two years of use. It cost almost as much as a new dishwasher (492 dollars). The model of the Maytag dishwasher is MDB77479SBM3. This dishwasher looks good from the outside and runs quite but the electronics are cheap and cant stand heat without melting. My wife and I are retired and only used this washer about twice per week. It looks good, cost 650 bucks and it is a pile of junk. No more Maytag in our house. We had this machine installed in July of 2014... It crapped out in July of 2016.

Well, Im confused and nervous! Ive read the reviews and I LOVE my Bravos washer - cleans unbelievable, its quiet, no rattling of pipes. My daughter was highly impressed when she was visiting with her daughters. She told me my washer got stains out of her kids clothes that her washer could not! Im confused because of the number of bad reviews for this washer - maybe they changed the washer? Mine is about 3 years old and I am SO happy with it! No agitator, but cleans so well. Terrified if it dies on me, I wont be able to replace it.

These machines have lots of service problems, although Im not familiar with the newer models. The function and the features are adequate, and typical. And overall, again, I have no complaints other than shortly after purchasing, there was a circuit board recall for these machines, and fortunately, I had a repairman who knew of the issue, and guided me to a cost free fix. Overall, it has served the purpose well of cleaning my clothes in a decent fashion.

This washer is garbage. Control panel went out twice in less than a year

I purchased my Maytag dishwasher thru Costco. I did so because I got a 2 year warranty if I bought thru them. The washer was approximately 6 months old and they replaced the pump. Approximately 3 months later they replaced the heater. Approximately 4 months after that they replaced the entire operating/electronic board located in the door. Approximately 6 weeks before the warranty was up they had to rebuild the middle dish tray. Now that the warranty is expired by 2 months the door is leaking like a sieve. Unlike most families we use our dishwasher at least twice daily. In summation I would not recommend this brand of appliances to anyone. I will not pay to have this one repaired.

The washer drum fills up with very little water, very little. I can do an entire load of laundry and the stuff on top doesnt ever get wet. Went on Spring Break in Florida and a month later our clothes still smell like the beach. Grill out, and I smell steaks the next time I put on the shirt. Stain your clothes in any way, its there forever unless you hand wash it first.To get it to work at all, each time I have to start the wash cycle (I leave the soap out just to save it for the next start), let the drum fill with water, pause it, get all the clothes wet, then cancel the cycle. After it drains and the machine is off and full of wet clothes, then start it all over again adding soap this time. On the second try, set at deep cycle, it will add enough water to cover the clothes - Im guessing because it senses more clothes because the clothes are now wet from the first, cancelled cycle. During the wash cycle, Ill open the lid and robustly move everything around, almost hand washing. #Handy. The dryer is fine, Im keeping it. The washer, cant return it - been three months of this frustration (kept believing it was me, reset it multiple times, change the settings, tried everything). Im buying a new one and throwing this junk out. $700 lesson.

Every appliance in my kitchen is Maytag. I went with Maytag because its made in America and now Im annoyed. The microwave died after about 5 years and since I had a spare, I have yet to repair it. I am just now removing the panel to see whats going on in the inside so I can replace whatever broken part is broken. The double oven I have Ive had to repair twice. Once I had to replace a capacitor on the board because it blew. It cost me zero to replace it as I have an old home theater system I part out. The next item was the control pad itself which I tried to repair but had to replace for $200. The dishwasher died after 6 years of use and after replacing the control pad (couldnt be repaired), it still didnt work. And I got a replacement from my wifes dad who was moving and had to get rid of his. Ultimate timing. I purchased a Maytag refrigerator instead of a Samsung like an idiot (which I suppose I am at this point). The fridge leaks water because the drain plug is jammed and it will take a lot of work to get back there to unjam it. I think Maytag wants to sell you expensive parts that are doomed to break after a couple years of normal use. They want to send repair guys out to your house to charge you to fix their junk. I cant wait to move and buy all Samsung products and do away with this Maytag relationship once and for all.

Our Maytag microwave MMV4205FZ-0 has the same ubiquitous problem as so many reviewers have mentioned. The microwave refuses to turn on (always at the most inopportune moments--like when the entire family is over for dinner. It doesnt matter how many times you open and close the door, it will often refuse to start. I think the worst part about this situation is that there are so many reviewers experiencing the exact same problem. Imagine how many havent posted a review. Doesnt it seem as though a rethinking of the door switch would have been in order long ago along with a recall? The fact that hasnt happened after so long and so many customers who are disappointed in their purchase is a sad commentary.

I bought a Maytag washer and dryer about 2 years ago. I’m on my second washing machine (one was replaced from Lowe’s not Maytag). The second washer has now gone out! First it was the lid lock and now who knows! The repairman can’t even fix it. Biggest piece of crap, stay clear!! My first set lasted 25 years. Poor quality workmanship and customer service!!

Bought in July 2014, third service call already! To replace my 6 years old Maytag Centennial thinking I was doing a good thing to upgrade to an HE... HA! Jokes on me! Washing machine: Water level. How can you wash clothes in 1 inch of water??? Noise. Very noisy at every cycle. Shakes and easily unbalanced. Clothes are still dirty after wash (obviously if not enough water). Dryer. Noisy with sporadic blower sound (like a plane taking off - high pitched). Three service calls in 6 months??? 2 calls for cable suspensions and now waiting over a month for the tech to change the drum completely. Good thing that I took an extended guarantee, for an extra $300.00!! After Ive read the over 400 complaints about this product, I really feel like I got screwed! My last Maytag EVER!

The refrigerator is not keeping cold. The freezer is full of frost/ice. I had this fridge looked at twice in the past. Its about 6-7 years old.In the past, Maytag was considered a high end product. I wonder where the manufacturing is taking place for most of the parts. Could be it was cheaper to go overseas and now we are all paying for unacceptable products.I will never purchase Maytag. Maytag should be selling products they can stand behind! Products that are made in the USA, where our standards are higher and we expect products that work!

I moved into an apartment home in June 2016. My apartment was furnished with all new appliances. The washer & dryer were purchased in May 2016. I live alone so on average I do 1 load of laundry per week. In November I noticed paint peeling on the inside of the dryer drum. Each time I use the dryer more paint peels. I contacted Maytag because I figured the dryer was still under some type of warranty. They sent out a technician only to tell me this was a cosmetic problem and cosmetic problems are not covered under the 10 year warranty. I would need an authorization code from Maytag if it was covered under warranty.Again, I contacted Maytag and now they want to send another technician for a second opinion. I dont feel this is cosmetic because the dryer is only 6 months old and already the paint is peeling. I feel this is a product defect because this type of problem shouldnt happen on a new appliance. I have scheduled an appointment for a second opinion and if he says its cosmetic then I have to pay out of pocket for the repairs to fix the problem. I thought Maytag stood by their product and customer satisfaction was a top priority. I guess I was wrong.

Bought the pair of Maytags on sale at Lowes 6 years ago. They are commercial grade and wash everything. Have had no issues - works every time. It took a while to get used to not have an agitator but now it seems natural. Would buy again.