You would be better off going to the river and washing your clothes with rocks. Piece of junk. Maytag will have you believe that the six inches of water this washer uses to clean a comforter is enough. I would like to know which individuals in the dept of energy thought this water saving feature was a novel idea. What use is a giant washer tub if it doesn’t have enough water. Sorry Maytag, my clothes used to come out clean with your old model, now I spend hours trying to figure out ways to get this washer to clean. Currently I am using the clean washer cycle for my comforters and then using the deep water cycle. So it takes about four hours to do a load of clothes. Thanks Maytag! This Maytag Bravos XL washer stinks.

MFF2558VEM0 - Had the same problem repaired less than years ago.. Now has the same problem. Looking for a new fridge. Hope better luck this time.

We bought a washer & dryer from Home Depot 2 1/2 years ago. The control board went out on my washer. I called Maytag and they wanted $109 for a diagnostic fee and wouldnt tell me how much the labor would be. A control board costs $350. So by the time all is said and done... the money would be better spent buying a new one. Maytags slogan of dependability lasts is a bunch of hooey. Washers should last more than 2 1/2 years and Maytag should back up their appliances. They just lost a customer.

The door is worthless. I am the only washing machine user in my home and am gentle with my appliances. However over normal use, the washers door has cracked and has had to be replaced twice since it was purchased from Home Depot.

I purchased a Maytag energy efficient dishwasher in June of 2010 along with an extended warranty that I keep extending. Cost $ but needed. Issue: Sensor in Panel fails so far every year and needs to be replaced. The repair technician showed me the sensor strip and indicated that this has been a big problem. (At least I have a warranty; however, it is a big pain to have to schedule a service repair person to fix the problem.) Repair (Sears) is EXCELLENT with great customer service. I did contact Maytag and there has been no recall.I own other Maytag appliances such as a washing machine and refrigerator with no issues there. In any case, I needed to replace my clothes dryer and did not select a Maytag. I purchased a GE very simple product with no sensor/bells and whistles. Not sure if I will go back to Maytag in the future - depends upon how they handle problems with their appliances. I would rather pay extra money for quality, durability, and reliability than go through the inconvenience from parts that are not made well enough to hold up.

Maytag dishwasher mdbh979sam1 - Every single one of the Maytag/whirlpool dishwashers with soft pushbuttons and LEDs will fail--check it on YouTube. They have a very thin printed circuit strip from the door controller to the brains, and this rusts through in a few years. You must buy the whole controller for $150, you cant replace just the ribbon. And youll be doing this every few years. Maytag disavows this if you call them. The design runs the steam past this ribbon, so it corrodes really fast. Get a real pushbutton or a real dial knob model instead. With this model, the issue shows up when the LED pushbuttons stop responding or randomly light.

This Maytag refrigerator is very nice.. Sleek black with double doors and ice two ways and filtered water on the door which is very convenient. The filters are expensive but they last up to six months so that part isn’t too bad.

The top of the range has blistered and has worn off. It cannot be cleaned. I spoke to a Maytag representative and was told to try and use magic eraser to clean around the burners. This did not work. The model number is mgr7775xs. Is there any solution to this problem. My range looks terrible.

I purchased this Maytag Dishwasher Model MDB8949SBM on November 23, 2013 and installed dishwasher in late January after new cabinets/countertops were installed. After four months the control board failed. I live out in the country and Maytag does not pay for a repairman to make a special trip for repairs, so we had to wait 2 weeks when the repairman was in the area. We purchased this dishwasher on reviews which seemed pretty good, but never bothered to check on complaints of Maytag dishwashers. I can see most all complaints are the control panels failing. Well it is November 19th and the control panel has failed again. My wife said the lights blink and when she presses a wash cycle, a different wash cycle will light and blink. She will press the start button and nothing happens. You can bet I will call first thing in the morning as the warranty will expire in a few days and I will write the persons name down and the time that I talked being that Maytag seems to lose conversations with customers. I hope Maytag doesnt give me the runaround like may others on this site. I dont understand why Maytag doesnt correct this problem that they have known about for years.

I purchased a Maytag dish washer (not even 2 years old yet). I bought it on 8/29/10 and I paid over $400.00 for it brand new. The model number is MDBH949AWW1 and the serial number is F03422327. I am only asking for the part (motherboard). I have lots of friends and associates at church, work and social that I have talked to about this Maytag. And I would like to give a good report about the company and what they make and that they stand behind their workmanship. I know for a fact that they have 22 motherboards on hand ready to go out and what I have read online is that many people are having the same problem. I need a motherboard. I believe this unit should easily last over 10 years, so I am not asking for much. I will have it installed myself. I just need the part. I trust that you are a reputable company that has been around for many years and Whirlpool has taken new ownership and they have been around for a long time, too! My own parents owned one for over 30 years. This is all that I would request. I’m thanking you in advance.

I purchased my Maytag washer and dryer set from the Maytag store in Glendale, AZ in September 2005. I even bought the stands for them. With my purchase, I got the extended warranty for four more years. I didnt realize that I would really need it. I have had so many issues with the washer and dryer I cant even count - from the control panel not working, to the noise and the vibration when washing, or maybe in the smell of moldy cheese. I also have issues with the constant chimes of D5 code that keeps coming up on the display screen. After 2009, I finally gave up on calling the Maytag customer service folks to have someone come and service the washer because it was out of warranty. I just decided to live with all those issues.As far as my dryer goes, the rollers went bad and that was replaced. The burnt smell isnt so bad as long as you use a wire hanger with a sock on the end of it and clean the inside of the vent. Then try to vacuum it, take the sock, get it wet, and clean the inside of the vent again. This was the most expensive piece of junk I have ever purchased in my life (almost $3,000.00 with the stands and warranty).What really gets me upset is I had the Maytag people servicing my washer and dryer up until 2009 and no one told me about a recall of my washer and dryer. The only reason I found out about it was searching for the specs as the washer finally died and I am replacing it. Trust me. I will not be purchasing a Maytag. I know that Whirlpool purchased Maytag so I am not even going to consider Whirlpool either. Since Whirlpool purchased Maytag, Whirlpool should have contacted all Maytag consumers, (which they didnt), put ads in newspapers (which I did not see) or put an ad on TV. None of these appeared to have happened.By the way, when I bought my Maytag appliances, I was supposed to get a $200 rebate for buying the stands that never came. It must have gotten lost in the mail - as well as the Tide coupons for three years. You, guys, remember that too. I will never ever purchase a Maytag appliance or Whirlpool, since they own Maytag now.

I bought the Maytag Bravo XL washer and dryer several years ago after reading many reviews. I like the glass top of the washing machine and the front door glass on the dryer. The dryer is fine its the washing machine that does not perform like the old machines. Whoever came up with the bright idea of saving water by cutting down the volume in your machine to about 6 inches for a good size load probably have never used a washing machine in their life. It does not get your clothes clean and does not get the soap out of a clothing to my satisfaction. Who made this suggestion? Could it be the same branch of government that made everybody use those spiral light bulbs years ago? The fluorescence that give off loads of EMF?

We have had 2 Maytag dishwashers only last less than 2 years. Since we can only have a portable because of owning an older home the expense is too much anymore. We also had a Maytag Neptune clothes washer last only 2 1/2 years. We had always respected Maytag and trusted them. That trust is gone. It is too expensive to buy and lose them after barely 1 1/2 years. We had a Kenmore that lasted 23 years. I dont know what company to trust anymore. The one we just had quit working a month ago was purchased October 3013. Maytag dishwasher Model #MCD4809PAW2 Serial #F34003436.

The washing machine is great as long as you’re washing small loads. If you try to wash a large load or heavily soiled items it does not get them fully clean. I have had absolutely no problems with the dryer except that I have had to replace the handle on the door which was a very inexpensive repair.

Purchased a supposedly top-of-the-line Maytag washer and dryer (9000 Series with Steam and MCT-Maytag Commercial Technology; Washer MHWE900VJ). Just under five years of use and the repairman quotes me just over $1000 parts and labor with the overwhelming majority of that quote being parts. No wonder the Maytag repairman is the loneliest guy in town - its not worth fixing your not-yet-5-year-old machine. It kills me that companies are allowed to advertise and promote the quality and reliability of their products and less than 5 years later, the machine is going to the dump, after having paid a premium for quality. This technology was supposedly comparable to what is used in a commercial setting - not very believable in my opinion. No more Maytag or Whirlpool for me.

My Maytag dishwasher which is less than 2 yrs old had its control panel and board gone bad. It took almost $400 to fix it. It seems like an ongoing problem and Maytag does not do anything. I would have bought a new dishwasher for that price, but I was already in for almost $200.00. They dont give you prices upfront.

I purchased this washer in 2010. It has broken 4 times since purchase for the same reason. I was told by the appliance repairperson (which Maytag referred me to last time it broke on 03-11-11) that the manufacturer does not replace the machine until after it has broken down a 4th time. Now, the warranty has expired (in 09-11), and it has broken down again for the same problem - water wont fill. Sherry at call center informed me my machine does not qualify for replacement. Then, she would not give me a number or contact info for corporate office so I could forward my complaint. This machine is only slightly over a year old. I have had nothing but problems with it. I want a new machine, or at least unlimited repairs for the recurring problem. And I should not have to pay for a warranty that costs almost as much as the machine itself when Ive already paid for the machine, and at least an equal amount to the cost of the washer in repair bills just to keep this lemon on the road. I want a number and a name for someone that will listen. I may be part of the shrinking middle class, but I am a customer, and I should be treated right. Please help me.

I have on the Maytag dishwasher for about a year. Is very quiet, the dishes are not clean. I called three repair guys from Maytag. The first time they replace the pump. Second time the guy said he just had a designed machine is no good.

Dishes did not get clean. Bowls would stand up when you placed them in the dishwasher, then fall over when the door closed and came out dirty. The rims of glasses were not clean. I had several 3 service calls and changed dishwasher soap several times per their suggestions. I contacted Maytag and was told that the only warranty was for mechanical problems and since the problem was not mechanical there was no warranty. I then went through the Better Business Bureau. The ultimate decision from Whirlpool was It has been determined there are no defects with the dishwasher and the issue is use and care. Mrs. **s request for a refund is respectfully denied. I have purchased a new dishwasher which does clean the dishes and the Maytag is sitting in my garage gathering dust.

We purchased our Maytag dryer at Home Depot a couple of months ago. We just called Home Depot for the second time because the dryer handle broke off while opening the front load door. We called Maytag and they tell us to call Home Depot and the only thing they are willing to do again is fix the door handle which will probably break off again while Im in the middle of laundry and cant retrieve clothes from the dryer because there isnt a handle to open it.Im convinced the dryer has a defective handle, and the dryer should be replaced considering what we paid for it. But Maytag or Home Depot doesnt want to do that. I will never buy Maytag products again and thinking of buying products at small appliance stores who stand behind their products, instead of Home Depot who could easily turn our dryer over to the insurance company as defective for the loss.

My Maytag washer is only three years old and the control panel completely went. Not only did it cost me the service call, they want $360 to replace the control panel. I called Maytag/Whirlpool to see if they would help with the cost of the part. I am 60 years old and the only one who uses the washing machine. It is not beat up. Maytag would not offer any solution at all and refused to even pay for any part of the control panel. They said it was really my tough luck for not having bought the extended warranty. When you spend so much for an appliance, you do not expect it to only last three years and you should not need an extended warranty. I am so disappointed and I will never buy a Maytag or anything from its parent company Whirlpool.

Bought top of line Maytag dryer and washer in 2011. Immediately had problems with dryer. Dryer resets timer itself to outrageous times. Clothes so dry they could have been parchment. This has continued with multiple service calls and electronics replaced. Still continuing but they will not act lemon law. I have extended warranties but get runaround everyone including Sears where I bought it pointing to each other. Tech came out today and said problem was the way the dryer is. No way to change it. I guess that is nature of the beast. I will never buy Maytag or from Sears again.

#Mgt8885x500 Maytag Gemini. After oven heats up, racks fall. What should I do. This is a safety issue. Help, afraid to use oven.

Bought a Maytag Bravos washer 21/2 years ago... already have to buy a new washer... not a Maytag!! It started with the ul message coming on. Never could do anything to get it to go off.... then started leaking water around the bottom... bearings went out... costs more to fix than buying a new washer which is what I DID. Not a Maytag.... thought Maytags were a great product. Believe me their repairmen are always busy, not just sitting around like in their commercial.... Never buy a Maytag appliance again.

I was repairing this Maytag Maxima washer and was almost electrocuted. I simply grabbed the wrong screws which were too long for the door switch, one screw went through into the open/close switch and contacted voltage, thus causing a direct short to the chassis and me. It also damaged my control board (the most expensive one in the industry), now Im out an extra $220 because Whirlpool made an engineering error. A screw should not be located so close (millimeters) to a voltage source where a simple mindless mistake could cause electrocution and possibly death. As for the washers operation, the drain pump failed after just two years, it sometimes leaks water out the front because debris gets into the boot drain back holes. It smells like mildew even though we leave the door open, my clothes stink, Affresh is costly and really doesnt help much. It does a decent job of cleaning, not as good as the old top loaders but it saves water. I think next tax return time this machine goes up for sale and we get a better machine.

Have a Bravo Quiet Series 300, does not clean clothes because on not enough water to wash with. Have to set it on Bulk to have it clean good enough. The way it agitate and rotate the clothes turns the wash into knotted pretzels (this also makes it harder to clean the clothes) which in turn makes the spin cycle vibrate badly. Cannot put wash in and leave because of this.

This Maytag (Whirlpool) model MDB7749SBMI dishwasher was purchased 10/28/13 at Home Depot. That makes it 2 1/2 years old to date. It has been a good dishwasher up until now. A few weeks ago I noticed it was doing something wonky. First of all it was not responding its usual way when I tried to turn it on after closing the door. The start button was not responding immediately, nor were some of the other buttons. I also noticed that after the dry cycle had completed and the door was then opened to unload, that the lights on the door were flashing. Then, when I shut the door after unloading the dishes, the washer would come on without having any buttons pushed. Recently, in addition to the difficulty we are experiencing getting it to start, the washer will keep running without ever turning off. Last night I turned it on before going to bed, and it was still running this morning. Calling the service number, the control panel part will run around $150, with a $98 charge for repairman to come out. Who knows if that 98$ isnt just to walk in the door, and whether that includes the time it takes to install the part. The dishwasher was around $400 with my husbands military discount from Home Depot, so it seems crazy to spend that kind of money to have a part replaced that is going to break again because of PLANNED OBSOLESCENCE. If that part is replaced (at half the cost of the dishwasher) whos to say what other part is going to break next, perhaps requiring another service call plus price of part. So, conclusion is to throw this one in the landfill and purchase another dishwasher, sadly.The case of Planned Obsolescence is reflected in many of the comments/reports here on Consumer Affairs. The age of the failing control panels of the Maytag/Whirlpool washers are running around the same time spans. No doubt in my mind that these control panels are designed to fail after a specific amount of run cycles/time on this machine. These appliance companies that are manufacturing these total crap appliances so that people will have to buy replacements within 3 or 4 years are filling our already packed landfills while robbing the consumer. Its plain to see for all who care to investigate the matter. A service repairman whom Ive used for years and has been in the business for 25, told me that most appliances today are total pieces of junk compared what they used to be and are designed to fail. He said it has greatly impacted his business because people are replacing appliances versus repairing them because it is not cost effective to have them repaired. He also added that the guts of these appliances looked like they were made from Cracker Jack toy quality plastic materials. There should be laws to stop these manufactures from Planned Obsolescence, and we need to go back to the way appliances use to be made... to last! I have no idea what its going to take to ever see that happen. This is what happens when you have very little competition and 2 major appliance manufacturers. More parts are being designed to fail, so that they can line their pockets. Pitiful.

I bought this washer (Maytag HE) almost a year ago, and if I could redo my choice, I would not choose this machine. There is no separate spin cycle. Often items are left with quite a bit of water in at the end of the wash cycle (often literally dripping as you transfer to the dryer), and you cant just rearrange them in the washer and then spin again. The only option on the washer is to both rinse and spin, which almost never helps get out more water. So you then have a heavy load in the dryer, much longer dryer time, and higher utility bills to get some loads dry, especially bath towels, sheets, jeans, etc. The washer is large capacity, but if you fill it more than 1/2 to 2/3 full (depending on the heaviness of your items) the spin cycle definitely will not get nearly enough water out of the clothes. The lid on the washer is SLOPED!The most ridiculous design I have ever seen for a washer, everything you set on top, even for a moment - laundry detergent, folded clothes, wet clothes - ends up on the floor. And the lack of agitator means at the end of the cycle, some loads that contain a sheet or any large flat item (tablecloth, etc.) the rest of the items are captured below the larger flat item that is over them like a mushroom cap. You cant tell how long the items have been like that in the washer, but its hard to imagine they are getting properly cleaned and rinsed. You absolutely cannot use powder stain removers, especially OxiClean, unless you are using the oxi cycle (much longer than regular cycle) because with any other cycle you will have white cloudy patches on all your clothes and items where the powder dissolved in the water but did not rinse out. You have to manually scrub them out, as putting these items through another wash cycle does not remove all the spots.

On 7/8/11, the non-freezer part of the refrigerator failed to cool to needed temperature. This fridge is model MI TXEMMWWOO, with serial no EY4705715, purchased on 7/13/10 at Home Depot.We contacted Maytag and were told to wait until Monday. On Monday, we were told that a serviceman would be out on Thursday, the 14th. On Wednesday, the 13th, the serviceman called to inform us that he would come the next day and that he would have to collect for the call. Since the fridge was still under warranty, we demurred.We went to Home Depot for advice. They called Maytag, and after an hour of getting the runaround, we were told that the serviceman would come on the 19th and that the call would be covered by the warranty.On the 18th, the serviceman called with the same message as before: he would have to collect the charges for the service call. Another trip to Home Depot led to the advice to activate the extended warranty at this point.Under the extended warranty, the serviceman came on the 21st, had to order a new part, and finally installed the new part on the 29th, three weeks after the misery began, and after spoiled foods, many bags of ice, and great inconvenience.We have other Maytag appliances, but this purchase has been a cruel lesson in Maytags lack of product quality, deceptive warranty practice, and indifference to consumer satisfaction.

I purchased a washer in July and its already off track. When I seen it I know it was junk but the sales person assured me it was a good product. 3 months later its off track. No spinning. DO NOT WASTE YOUR MONEY.

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

Purchased a pair washer/dryer Maytag Bravo XL module from Home Depot, Brentwood, CA #1076 branch. The first day I received my machines, the dryer had a defect. I called them within 24 hours to report the issue and requesting a return. Home Depot wont take it back; they said I have to go though the factory warranty to fix any problems. Its like buying a car, once you drive it off the lot its yours they said. 3 weeks after the washer started making noise. Home Depot kept delaying my claim for more than six month so I couldnt dispute the charges with the credit card company and avoid the California lemon law. I consider this a loss of money and time. Worst appliance purchase experience ever.

We purchased our Maytag dishwasher on 12-26-2013. It was installed in early Jan. We did not buy an additional warranty. We put our faith in the Maytag name. We had no problems with our dishwasher. It was smooth and quiet. The one year warranty ended in Jan. 2015. In March of 2015, our dishwasher control panel began to go crazy. A short while later our Maytag shut down completely. Every now and then the washer will come on by itself. We will try and cut it off. It cuts off when it is ready. We have got quotes on getting it fixed by Maytag. With installation and tax, our Maytag Dishwasher cost us $649.22. Our complaint is the same complaint of thousands of other customers - the control panel. Maytag should have a recall and fix this problem. Maytags remedy for this problem is to sell a warranty for each year that a family owns the dishwasher. That is not acceptable. Please consider a recall on this item. Our model is MDB7749SBW2. Our serial #F33406909. Thanks for your help.

Bought this washer and dryer 3 1/2 years ago mainly because of Maytag name and reputation. They were very expensive to purchase. The washer is a piece of junk 3 1/2 years old used for my wife and I and leaks oil all over the floor. Called repair man to come and look at it, wasnt here 5 minutes said transmission is shot. Cost over $400 to have it repaired. We are junking it and that will be the last Maytag product I ever own.

After reading all the reviews I realize this is a wide spread complaint. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. You press the keys and hope for the best. I am thinking of going to the media with my complaint. Maybe we will all get some sort of refund or upgrade.

Purchase of what we thought was high quality Maytag dishwasher. Paid $600 and $250 to get it installed, which was really just to take out the old dishwasher we wish now we had kept, and plug in the new one. After 2 years, repairs needed to replace the control panel and key pad must be replaced, cost $340 plus labor. We will never buy Maytag again. Called their hotline, 800-877-6777. They cannot offer any help. Called the co. we bought it from, a Maytag dealer, Haleys Maytag of Antigonish, Nova Scotia. They too offered nothing except to sell us parts... control panel and key pad. Called lawyer who has class action suit now against Maytag, Eppsteiner & Florica. They are not representing customers who live in Canada, only U.S.My recommendation to Maytag dealer who only sells Maytags, Haleys Maytag of Antigonish, Nova Scotia, find another company to represent. Maytag is a real loser. Never again purchase a Maytag, and I told 10 people who will tell 10 people... who will tell 10 people. Our model number... same as all of yours... the loser MDB6709AWW1. Dont waste your money buying this overpriced dishwasher that will then require you to spend more money every 2 years on a Control panel and Key pad that are defective from the factory.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

I just off the phone with Maytag and as expected the acted like they didnt know about the issue of fires and etc. Im a senior and also a widow. I have all Maytag appliances. But not anymore! My Maytag over the range microwave model number MMV4250AAW, would not shut off when I had it set to 1 minute on reheat. I unplugged it and now it wont come on at all even though the cord still has power. Dont buy Maytag! Maybe if they get messages from consumers, they might be interested in what we have to say.

I have always had faith in Maytag when it comes to appliances. As of yesterday, it is gone. We purchased the Bravos XL dryer in January 2013. Last weekend it was running, but not drying. We placed a call for a serviceman to come fix it. Discovered the heating element had gone out on it. We had to pay $300 for the repair. I am greatly disappointed a $1,000+ dryer is already having issues. Maytag should stand behind this problem and offer to pay for the damages, as from reading the reviews, it looks like this is an ongoing problem. Maytag should be ashamed of providing a product of such poor quality.

Purchased new Neptune stacks in 2002 and had several service calls on our expense and we noticed the hinges on the washer door were rusting! Ordered new ones from dealer but rust continues and has spread to top of machine over the bleach dispenser. The metal is falling off! Bad rust on the inside lip under door also. I contacted Maytag when I first noticed rust and they blew me off so I contacted the local dealer we bought from and they did nothing to help. Will never buy Maytag again and have not recommended it to anyone else either. ModelINGooZES. Serial: 51867064AJ.

I purchased the Maytag metal interior two years ago, the very first year I had to replace the control panel board... Now, the panel went out again, after calling the Maytag executive office, they finally sent me the part, telling me I had to pay to get it fixed. That was just three months ago... Presently, the dishwasher has quit running water in the cycle... I will NEVER purchase another Maytag dishwasher... thinking you get The Best doesnt mean what you think... BEWARE...

Have had this set for about three years (was a gift from my parents on having our first child), and its horrible. Clothes come out partially dry, with NEW stains on them, torn or frayed, and twisted into knots. Its supposed to be a high-efficiency washer but we often have to wash things twice to get them clean. We now have two little boys and Im starting to save to buy a different set (no Maytag ever again); disgusted that I cant even sell this set in good conscience. Will either be a donation or an eyesore for the landfill. Worst $1100 ever spent.

I bought a new Maytag dryer model # MEDC555DW2 18 months ago. Prior I had owned a Whirlpool for 22 years and the only expense on maintenance was that I replaced 3 belts. This new Maytag started making a terrible noise so I called the store where I bought and they sent out a tech. $76.77 they charged me to...remove a penny from where it got lodged in the edge of the drum somehow. Maytag refuses to do anything about it and I feel like Ive gotten the shaft because I bought an inferior product. In 22 years Id guess I dried on accident over 100 dollars in change since I have kids. Should have bought a Whirlpool again and so should you. Ill never buy another Maytag product. Ever.

I bought this washer three years ago. It is the worst washer I have ever owned. Washing a load of clothes, it goes off balance constantly, large load, small load...it doesnt matter. The smell because of low water usage is awful, and the clothes dont come out clean. I have to buy a new one and that really stinks. Maytag youre off my list for purchases. These days its quality that will keep you in business. We are too smart for this garbage.

Maytag Bravos XL - I have always loved Maytag and never had any problems. In Feb we did some major remodeling with new flooring in our laundry room. Decided to buy a brand new washer and dryer even though our 10-year old Maytag washer and dryer worked perfectly fine. After looking at Home Depot and Lowes we first settled for a Samsung W & D but before it was delivered we shopped some more. After doing some inquiring we decided that we wanted to stick to a long trusted W & D line so we chose this washing mashing and matching dryer. From day one I decided I did not care for it. I found if I put too many clothes in that they did not come out clean. Any dark pants would come out with what looked to be soap or softener stains and would have to rewash 1 or 2 times. Now I can only put in about 4 pairs of pants to wash. I have been cleaning it once a month as the manual says to do but yesterday I noticed a terrible odor coming for the washer. I could smell it out in the hall. I did the cleaning again but still smell it. Now after searching the internet I find a video that shows the problem is mold under the drum. No amount of Affresh or bleach is going to clean something UNDER the drum. It is not my job to have to take this apart every few months and clean out mold and moldy water. Sounds like this problem has been going on for a few years and this should have been fixed long before this. I wish I had my old faithful washer and dryer back. Maybe I should have stuck to the Samsung washer and dryer.

I purchased Maytag washer, as it was rated the best of the best at the store. First of all, Delicates cycle washes exactly like Normal. All my sweaters got ruined as the agitation is VERY HARD. I dont think the manufacture even knows what that cycle means! Absolutely awful! Theres no difference between Delicates and any other cycle!Second, Deep fill cycle. If you select off on that cycle the clothes get hardly damp. HOW can you wash hardly damp clothes???? If you go with Deep fill, the washer is supposed to weigh your laundry 1st and ONLY pour the water according to the weight. Well.... you can put only 5 small items and the washer fills all the way to the top! What the hell is this???? How can few items fill such a ginormous washer???? It doesnt work! Im so pissed and want this washer out of my laundry room!

I bought a Maytag refrigerator, model MBF2258XEW, March 2013. Bottom freezer, single door. The past 3 or 4 weeks I have been noticing water occasionally puddling on the floor at the freezer. The ice maker has never been hooked up, with no problem before now. I recently noticed that my wood floor is darkening in a spot that often gets wet. After reading some of these complaints it appears I am not alone experiencing water problems with something that is sold on its reputation for being trouble-free. I also see that I should expect to pay a few hundred dollars out of my pocket to fix the problem. Very disappointing.

My washer has always had an odor, and I clean the gasket. It gets mold on the gasket and smells horrible! Now for my dryer, it has 3 baffles inside that helps turn and fluff the clothes, and 2 of mine have broke off. And that results in clothes that look like they have been in the dryer for weeks. And I take them out as soon as they are done drying.

We ordered a new Bravos washer and dryer at the end of November but due to delivery snafus, we did not have both until the second week of December. Just yesterday, both failed. Part of the drum on the washer ripped off, and the dryer just stopped running an hour later. I am used to getting a long life out of appliances. The old dryer was over 20 years old, and while the old washer was only 17 years old, I thought it would be nice to get a matched set.

I recently purchased a Maytag centennial washer and dryer from my local Home Depot. I set up a delivery date of 2/9/12. I was contacted on 2/6/12 by a Maytag staff telling me that my washer and dryer were on back-order until 2/29/12. This is unacceptable to me. Why does your company not tell its retailers that some items may be back ordered? I would have accepted this if told when I scheduled my original delivery, but being told days later and after taking the day off from work, is poor customer service to me. I am giving very serious consideration to voiding this order and finding a new company to deal with. I do not have the confidence that future issues will be shared or dealt with in a timely manner.

I have a top loader Maytag washing machine, Model MVWB835DW4, bought in 11/2019. Five months of light use, the lid cracked. Received a replacement and four months later the lid once again cracked in the exact same spot. Requested replacement parts under warranty and I was told that a service tech must install the lid. Due to health and safety concerns related to Covid, we are not take any chances letting people into our home. My wife and I are 70 years old and are at high risk. Maytags response was they would not send parts under warranty to me and a service tech must install the parts. If I dont let them in by 11/2/2020 (the end of the warranty period) then I would have to pay for the parts. Maytag has the very worse customer service in the industry.

I have a gas dryer from Maytag that works very well. Very easy to use and economical using it with propane. Im pleased with my purchase. Ive had it now for about 8 months. I would recommend buying another one.

I purchased my home in 2008 at which time I bought all brand new Maytag appliances, well the above the stove microwave Ive had to replace the door handle because it broke off and the oven I can only use the very top or bottom to cook on and I cant move them, otherwise the racks will fall through. I have burned myself numerous times as I cant pull the racks in or out and I found that out cooking dinner and when I pulled it out the rack fell through and my dinner went crashing down and splashed everywhere. Due to this fact I hardly ever use it. I contacted Maytag with no help, told me to buy new racks and those did the same thing so it was a $100. It seems as though the liner cant handle the self clean heat and if you look at my oven, the left side is pushed in. If anyone gets help with this issue please let me know. My model number is MERH865RAS serial # 14348133LX. Oh and my refrigerator is a side by side and I have had to have it repaired twice because my food kept thawing out. That model number is MSD2651KES serial 60869476LV all of these are Maytag products and were purchased brand new from Home Depot.

I purchase my Maytag electric glass top stove 9 years ago. 2 years ago, one of the burners went out and had to be replaced. Now, in the past 2 days, my oven is taking FOREVER to preheat from 0 to 455 degrees. So far, its been 78 minutes waiting for it to go from 0 degrees to 425! Apparently the heating element is defective. As far as the self cleaning oven, it is absolutely worthless, and does NOT work! Needless to say that Im very disappointed, and looking at another repair expense!

Deceptive company and won’t stand behind their product! Purchased brand new washer. Identified and reported noise that I can hear upstairs in my house while washing to technician. Changed a part, not related to the noise. Called back out. He admitted he could hear the noise. Whirlpool engineering department says normal. Sorry, I should never hear a clicking noise upstairs with two closed doors and 150 feet between me and the washer. Will be going back to Samsung next time.

Maytag range model mer8875ws - Glass top broke on brand new oven over most used burner then glass spider lined out from there. Wife called Maytag and they told her that it broke from the impact of something dropping on it. I guess the man was psychic because he had no picture of SO CALLED IMPACT SITE. Now they wont replace or fix range, ** Maytag. Paid 699 for range they want to charge me 900 to fix. MMOOORROOONNSS! Like ** thats how big business treats everyone now. Thats how big business treats people these days.

We bought a Maytag Neptune Washer and from day one in 7/10/2004, we have had trouble with the washer and Sears. First, it stopped working within eight months after we paid over 1300 for washer and master protection agreement. We called over and over from that day and was told we didnt show in their system as owning one and that we didnt get the master protection agreement. This went on and on until they finally told us on 8/2010 that they finally did find us in the system and that the agreement had ended a year before and would send someone (that was on 8/31/10) to do the washer. After having sat for almost six years, it reset itself and worked that day. I told the guy from A&E that it was the computer but that wasnt what he replaced so the washer went right back on in a month. So we had to save to have someone else come out from A&E to charge us 143.10 to say it would cost a total of 310.51 for the computer and that it probably wouldnt work for too long.

Model MMV4205FZ3 microwave hood combination. No problems with open door signal yet. However, light over the stove burnt out. When removing, it exploded.No didnt unplug first. Previous microwave didnt have a problem with this. Instructions are useless. Didnt say to unplug and doesnt provide a model number for the bulb. Consequently, we have now purchased 5 different bulbs and they dont work. Tested socket and power is going to it. Rep at Ace Hardware said he had heard about this happening several times and provided what was to be the correct bulb -- didnt work.

Purchased this Whirlpool made Maytag Stainless Steel dishwasher Feb 2013. By Jan 2017 the washer was no longer operational. Due to poor factory design the touch pad wiring harness was crushed during the initial assembly. The harness is routed behind the touch pad/pull handle faceplate in the door. The factory design provided no clearance for the harness. Obviously after little use (opening and closing of the door) the pinched portion of the harness behind the pull handle becomes compromised causing the ELECTRICAL SHORT.I phoned Whirlpool the maker of the Maytag Stainless Steel Dishwasher for assistance, all they offered was a repair plan in excess of $300.00. I purchased this supposedly quality American Made Whirlpool product as well as a range, microwave, washer and dryer in the spirit of supporting US labor. Now Im stuck with a dishwasher that has an ELECTRICAL SHORT, possibly a FIRE HAZARD and Whirlpool trying to milk me for more money. Please think twice before purchasing anything from this Michigan based company.

Purchased Maytag washer Centennial Econoserve washer. It was 2 years old Aug 2013. Washer stopped working Sept 16, 2013. Of course since it had Maytag name brand, I did not purchase extended warranty due to thinking it would at least last more than several years. I called Maytag/Whirlpool. They gave me name of authorized repair in our area. So far they have come out 2 times. $560.00 later, it is still not working and they have no answer as to how or what to do. We are now into $1300.00 between purchase and repairs and still no washer. We are retired hard working people and this is really a bad way to treat consumers. Maytag customer service could care less about the situation. They just say we should have purchased extended warranty.

Purchased this double oven back in 2012 and have had to have the control valves replaced twice because of them jamming and snapping. The burners are undersized for cooking and it takes forever to get water to a rolling boil. The broiler in the upper oven needs constant attention when using it because food cooks unevenly and burns quickly. The lower oven is great, convection is awesome. I have seen the Maytag repairman more from my stove than I have for any of the other appliances I owe combined. Maytag should stick to appliances that only use water.

I will NEVER get another Maytag product ever again! My not even 1 year old washer broke and I have been waiting almost 2 1/2 months for a part to be replaced. My partner and I are nurses working on the front lines during this COVID pandemic and I can’t even wash my scrubs at my own house but instead I have to go to a damn washateria. The “supervisor” told me 2 weeks ago that if the part is not in by today, 1/27/21, that a brand new washer will be sent to me. Well I call today and the people I spoke to denied any recollection of this information. The “supervisor” stated that she is “documenting all of the information” so when I called back I would not have a problem. Once again I have been lied to and wasting my breath and time. The customer service has been TERRIBLE and I cannot believe that this was once a “reliable” brand! Clearly this brand is unreliable and the personnel is also unreliable. NEVER AGAIN WILL I BUY A MAYTAG! Save your money and buy a different brand!

Maytag gas range 5 burners. Maytag is quality. Period. I doubt that other brands are made as well. From the handle of the oven door to the ease of cleaning the burners, you wont find better for the price. I look for quality and reliability. I read reviews. A deal breaker on any major purchased would be too many bad reviews and shoddy materials or construction. This range has 3 regular burners, one large burner and one small burner. The oven shelves easily adjust from one level to another. The controls are easy to reach and the timer and bake controls are easy to operate.

After having issues with bearings in a front load of another brand, we decided upon a top load Maytag. We have had it less than a year and we are not happy with the performance. We are using more detergent because the dispenser seems to be bottomless. Only the front of the little pull out drawer is visible and it never seems to reach the fill line when adding liquid detergent. There is no quick wash cycle. Not everything needs a cycle of nearly an hour or more. The spin cycle does not remove nearly as much dampness/water as our previous frontload. The drum is deep making it difficult to retrieve small items such as socks. My biggest disappointment is finding lint residue on the clothing and it remains even after an extra rinse. This is especially visible on dark clothing. Even the lint filter in our dryer fills up much more quickly than before. After researching, I found that others complained of this same problem.

We bought our washer/dryer from Home Depot and felt Maytag was a good bet. Guess again. Washer is running fine for now but after light use (about 3 loads per week) dryer failed. With no warning, I heard a loud pop about 3 min into a cycle and overheating. If I hadnt been home might have caught on fire. Good for us we live close to a coin laundry so in no rush to replace but can bet when I do it wont be Maytag and thats too bad. One of the few makers still building in the USA but thinking Samsung is looking good. This is the Maytag 2000 series btw.

Had a brand new Maytag MDB4949 dishwasher installed on 10/20/15. Noticed an acrid smell of burning plastic coming from the pull handle. After going to the reviews I see a pattern of shorting control panel boards melting the ribbon cable. Having repaired Xerox copy machines for 17 years, I recognized the smell of an electronics short and melting plastic. There are 600+ complaints for the same thing. Going to call the store we purchased it from and will escalate from there.

Every time I do a load of wash, it comes out looking like I slept in it. It is so wrinkled you cant even iron it all out. If the load gets off balance, you have to wring it out by hand because you cant get it to spin again. I did a load of flannel sheets and it went off balance, wringing sheets out by hand is enough to make a person want to send the machine back and get an old-fashioned wringer washer. I hate this machine without an agitator. I have always used a Maytag washer, but I would not recommend this to anyone.

Washer exactly 3 months old, will not work. Maytag can tell you nothing, they just want your money. They called a repair service in our area, never heard from them. Here we sit no way to wash clothes. And they say will charge to fix it. WHAT IS WRONG WITH THIS PICTURE. FO NOT BUT MAYTAG ANYTHING.

I purchased a Maytag dishwasher (Model No. MDB8949SBWO) in September of 2013. Within the first year (and under warranty) the control module failed. The dishwasher is now almost two years old and the second control module has failed. From other postings it is obvious that Maytag has a known defect in their control units. To replace control modules on an annual basis makes this an extremely expensive dishwasher to own.

I have only had this Maytag dishwasher for 2 years. My control panel has gone crazy! The child lock is blinking and I never touched it. I have tried to clear it by touching the heated dry button for 3 seconds, every once in a while it will clear. It eventually will start blinking again on child lock. I did research and have found out that Im not the only one that is having this problem. I now have to get it fixed.

Had it for over ten years, had no problems. We dont use the oven too often but it is simple to operate and has served us well. Easy to clean, stainless steel like looks on the front goes well with our other appliances. Reasonably priced too.

Although this refrigerator is 10 yrs old it really performs well. I like the ice maker as it hardly ever hangs up, the freezer works great and the refrigerator part is really super in the veg drawer and the meat and cheese drawer. All in all this was a great buy.

We have a Maytag Dishwasher Model MDBTT60AWB purchased from Lowes about 8 or 9 years ago. This model was included in the huge 2010 recall of 1.7 million units due to the possibility of heater-unit fires. For the last couple of years, its had a problem staying on the selected cycle: After being started on normal wash, it reverted to rinse only after a few seconds, but eventually quit responded to the selection of other cycles altogether. Removing the back from the door to expose the innards revealed the ribbon cable that connects the circuit-board head to the control panel had worked loose. Reattaching it provides a temporary fix, but it eventually works loose again. We suppose the screw holding the back to the door will strip sooner or later, but by then well probably be so fed-up with fixing it that buying a new (non-Maytag) one wont seem like a bad option.

Maytag microwave MMV4205BAB - I purchased this microwave in 2007. By 2009, the whole inside was peeling down to the metal. Under the glass plate, the bottom is all rusted. Ive called customer service every year since 2009 and they say the same thing. No extended warranty, nothing they can do. They acknowledged that this was not normal, but they did nothing! Do not buy anything from Maytag. If you do, buy all of the expensive warranties or you will be sorry like I am.

I purchased both a Maytag Neptune washer and dryer in 2007. This is without a doubt one of the biggest mistake I have made. I have had the dryer drum and rollers replaced and the washer will no longer run. It is going to cost me hundreds of dollars to repair. To think I bought these units for 2 reasons: 1. that Maytag are the dependability people, but its not! and 2. Energy efficiency. It is not too efficient when they are broken more than they work. The worst was when the repairman told me that I had purchased the worst product on the market. These units are in short, garbage! I will never buy another Maytag Product!

Maytag used to have a reputation for quality. Their low water energy efficient Centennial is a waste of money. Half of the time clothes come out wet and most of the time they are still dirty. Also you are only supposed fill the tub 1/4 of the way with clothes so you end up doing 3 times as many loads per week. What genius came up with this idea? Save your money. You would get better results washing your clothes in a tub with a washboard. Seriously!

We have had our Maytag dishwasher for more than two years. Heres how it stacks up: Energy Star rated-Yes; Noise-Almost inaudible except when water runs; Length of Cycles-long except for quick wash 59 minutes; Interior design and loading - 10 out of 10. This is the easiest dishwasher to load and it holds an enormous amount of dishes of all sizes and shapes. Adjustable and removable racks-Yes both. Everything fits including my barbecue and oven racks! Amazing. Stainless interior-Yes including silverware rack. Cleaning- 10 out of 10. Even on a quick wash (59 min) cycle this dishwasher cleans everything! I run a longer cycle just to sanitize if we have sickness in the house. Otherwise it is 59 minutes to finish. Drying-Like most dishwashers this one is only so-so in the drying department, especially on the short cycle. Without plastic containers or utensils the machine dries more completely. However, the amount of moisture remaining after a quick or regular cycle is minimal. The water tends to pool on bottoms of glasses and plastics mostly. Easy to dry by laying a cloth across top rack. Dries in just a few minutes.My only suggestion to Maytag is to work on drying technology to make the machines more efficient and effective. However, that being said, I wouldnt trade this machine for any other. It has every feature I love and a 10-year warranty on parts as well! My machine cost around $600.00. It was neither the top nor the bottom of the line.

Updated on 08/13/2021: Today a repairman who is authorized by Maytag came out. He found the problem, some arm that popped out that is located underneath the washer. He put it back together and said he needs to order the part and it will take 30 more days. Set the washer so that it SHOULD work for a couple of loads. I spent $700 on a washing machine and I have to go to a laundry mat to get my clothes washed. Here is the clincher. The guy left no paperwork, nothing, not even a business card. So I am at the mercy of this repairman (I think he said his name was Jessie). The guy was friendly, quick and knowledgeable, however he told my husband he knew what the problem was going to be, if you knew why didnt you bring the part with you and he said the part is out of stock. Why, is this part unique to Maytag washers? So I am still waiting for my washer to be fixed.Original Review: In December 2020 I purchased a Maytag washer it was delivered in January 2021 and it worked great for the first several months. Then the machine started making noises, clicking noises like it couldnt move through the gears. Then I started noticing that my clothes were not getting cleaned. It was taking an hour to wash the clothes. I told my husband it is not agitating just clicking. We had to stop and start back up the washer just to get the water level high enough for the so called deep water wash. I was finding residue left on my clothes and had to wash them 2 or 3 times to get the clothes clean enough to wear. Sometimes it wont spin enough to empty the water in the tub. It smells almost like wire burning. It has barely been 6 months and I have to have a repairman out. I will review the washer again after it has been fixed or replaced. But as of right now I will never buy another Maytag again.

I bought a Maytag Dryer from Lowes in December of 2013. I paid 600.00 for this dryer which I thought was going to last for quite awhile. It stopped working in January of 2016. (2 years old). I had a repairman come out and he said the motor had burned out and he wanted 300.00 to fix it. I called Lowes and asked if I should expect the motor to burn out in 2 years; they said of course not - call Maytag. That proved to be a complete waste of time. They would do nothing. They simply said that there was not a recall on that machine and they were not technicians. However they would be glad to send someone for 125.00 dollars to look at it, then the parts and labor would be more. I have never had a dryer burn out in 2 years - not even when I was raising children and using a dryer daily. This Maytag clothes dryer isnt even used every week and when it is used, there are a few small loads. I am appalled and disappointed in Maytag and the poor quality of this appliance as well as their horrible customer service.

Bought a Maytag 4000 series washer and dryer combo for about 2100 dollars in October 2011. Had a professional look at it today since the clothes stayed wet after the spin cycle. Told us it would cost 1000 dollars to repair the washing machine. So a total write-off in barely four years. I am very disappointed.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

I bought my Maytag Bravos top load washer from Home Depot. In one year. I had the Maytag warranty people out three or four times. The warranty ran out and I purchased an extended warranty from A&E. I have had them out at least five times.I called Maytag and they told me since that I didn’t get the extended warranty from them, that there was nothing they could do for me. I explained to them that this washer cost me over $900 and that I have had numerous repairs on the washer, in which the warranties cost me over $400 so far.How much do I have to keep paying for this lemon? Maytag will not do anything about it! This goes to show you that paying top dollar for a washer does not guarantee you will have a good product. In this economy we can’t afford for this to happen. This is a very bad product and Maytag will not stand behind their own products, but they are willing to charge the consumer high dollar for them. This is a disgrace!

I bought a Maytag Top Loader March 2021, this washer machine is the worst ever. It doesnt clean your clothes, & your clothes stink horribly. BBB and an Attorney needs to compensate for our all buyers.

After a year, the plastic parts of Maytag dishwasher is breaking and upstairs propeller is no longer running. Do not buy this product. I made that mistake.

Washer would stop right after it started. I googled the problem and found out it was a bad lock. These Bravo XL units were purchased in 2015. Called an appliance repair and they charged me $250 to replace the lock (service call was $98.00 and labor was $90). The repairman left and I started the washer. There was a loud sound coming from it. I called the repairman back and he said it was the gear case and basket. He said the basket was covered under the warranty but the gear case wasnt. Would be about $750 to fix....no way was I paying the cost of a new washer to fix this less than 4 yr old one. I called Maytag. They couldnt help me. I should have purchased an extended warranty they said. The cost to purchase the extended warranty is now $394.00 per year....please do not purchase a Maytag/Whirlpool appliance unless you like buying extended warranties.

I too had to replace the control panel on my Maytag dishwasher which I purchased in 2007. I was told by my repairman to contact Maytag to see if they would do anything for me. When I called Maytag, I asked them if there were any issues with the control panels as I had heard there have been multiple issues with them needing to be replaced. I was told they had no record of any complaints and offered to sell me an extended warranty for $269, but there was nothing else they could do for me. I ultimately had my repairman order the part and it was replaced. My repairman did say Maytag did upgrade the panel because of all the issues they were having with the panel. Hopefully, they have fixed the problem and it will not have to be replaced again. But if it does, I will not replace it again. I will look into a new dishwasher and definitely not a Maytag. Yes, I would be interested in joining a class action suit.

I have had two Maytag washing machines in the past. Both lasted 20 years. Three years ago I purchased my first Maytag front loader washer and dryer. The washer is terrible. Although I clean it regularly plus spend money buying Affresh tablets and leave both the door and the soap dispenser open, the washer smells and builds up tons of mold. Cleaning out the heavy mold in the soap dispenser area is almost impossible. I spray bleach in there and then try to stick my arm into the back where most of the mold accumulates. Cant really get it all. Also, there is a problem with the softener dispenser. It gunks up and gets clogged. Had to keep pouring hot water and vinegar into it. Contacted customer service who was no help - they simply wrote to clean the machine. Huh? The dryer turns sheets into a tight roll with the inside not drying.

Washer is Broken After 1-1/2 Years: Yes, the code F51 has come on quite often. Now, my washer does not work at all! Does not spin out, makes thumping noises even though I have taken good care of this machine. It cost me quite a lot of money and thought that this was a wise decision. It’s broken after a year, unbelievable! Also, clothes don’t get clean. I had to wash 2 - 3 times. The clothes wrap around each other and the machine does not clean them well. It’s a horrible machine. I have not called Maytag (Whirlpool) yet as I see from the comments that they will not stand behind their machine. I dont know what to do!

I dislike Sears and more so Maytag. I bought a Maytag Bravo XL MCT. It worked nice with very few hiccups until 1 1/2 years old. Then the washer went to the lock and done mode, thought it might be the lid switch down the washer up. Looks like I would need to change out the whole panel. Its not worth the trouble OR time to put one dollar to repair the piece of **.

I bought a brand-new dryer Maytag Bravos. It broke after 3 weeks. They came to fix. A few months later, same thing happened, but I have 6 people in my house. They told me someone would be here the next day, and then that person canceled. They called someone else. He came and said I have to wait 3 days for parts. I called at least 6x and waited 30 minutes each time. They kept telling me theyd call back, and theres absolutely no call back. Then I called corporate Yvette, who was totally cocky and rude (866 817 5404). She said she would try to get back to me another day because she had meetings! Then, I was irate. I mean how rude. So she called me back and said, I ordered you the parts. Now you call Dan Marc, the service company, and make the appointment. Is this woman kidding? Then she went on about how Maytag has a 13% rating (They are Maytag.) and how their product is so wonderful. Now this woman is competent cocky and rude, and shes the presidents secretary! So whatever I call Dan Marc, they have no appointments Tom and wont make me an appointment. This is how a new product should work? I asked her what I do when it breaks again and again and the warranty is up. She told me they dont work on what ifs and if that time comes, it will be her decision. I am disgusted and have a house full of kids with no dryer? And I have given them another chance after that Neptune disaster. Im appalled and dont even know what to do.

I have owned this dishwasher about four years. After about three years the control panel malfunctioned and had to be replaced. Six months later I had to replace the controller. After another six months the control panel has again failed. Rather than invest more money in this beast, I have decided to replace it with what I hope is a more reliable machine. This experience has definitely put a bad taste in my mouth about Maytag products. I’m afraid this will be my last purchase of a Maytag product.

I purchased a floor model Maytag Dishwasher from Abt electronics about a year and a half ago. 2 months ago, various light started flashing. Somehow I managed to get it going. Some blogs reported it might be a drainage problem. Others suggested pressing a certain sequence of buttons. After Each time I got it to work, it became harder the next. I bought Maytag because my old dishwasher lasted 13 years. What is interesting is that a company whose name Ive forgotten sent me bimonthly requests to purchase a warranty from them. Now they have stopped. I am a single mom of 3 with an unemployed ex. I work and support my family without any assistance. I count every penny. I cannot afford repairs nor a replacement now or any time soon. This is a travesty.My door says 10-year limited warranty and the delineates stainless steel tub and racks and chopper blade, but not the panel. I do not understand how Maytags denial of the problem and their unwillingness to correct the problem can improve their image. I will never purchase from Maytag or its associated companies ever again. What a scam! To be honest though, I have not contacted the company since it is not under warranty and all the blogs have relayed the same message: Maytag denies there is a problem.

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

Bought this Maytag XL washer and dryer in September 2012. In January 2014, the washer stopped working. Service guy came out and said the electronics went out. Then in May 2014, the dryer died. The dryer door latch broke. Would not stay shut. 2 days later, the heating element went out. Again, the service man came out. This service man said that this model is subject to break downs. This Maytag is a piece of junk. I went out and bought a Whirlpool, which I had before. I would never buy a Maytag again. I paid over 2000.00 for this Maytag and it is the worst washer and dryer I have ever had. Apparently, the Maytag repairman needs to get his butt busy. I have the Maytag now on my sunporch, waiting for the junk man to come and get it.

I PURCHASED A WALL OVEN ABOUT 4 months ago. Used the self cleaning, oven blew fuse and some other part, had to wait for almost 2 weeks for repair because of self cleaning liner is now peeling and leaving fine particles. Maytag said it was ok, they would not replace, the liner doesnt have a replacement part so Im going to have to buy a new oven to feel safe for my family meal.

Maytag MVWC300BW clothes washer makes holes in heavy duty T shirts & sheets. It stretches clothing. We are following directions in loading without success. We are washing everything on the gentle cycle twice to get the clothes clean without destroying them. Today we were stood up for our third service call.

Maytag 7000 series front loaders bought in 2013 on basis of high ratings from Consumer Reports. Also durable and look good in the process. Had for 3 years. Machines highly rated by Consumer Reports and bought on sale. They were a very good value. Both W & D have steam feature but find Ive rarely used it. Durability is key, as is the ability to balance wide variety of loads, which our machines do well. Capacity of 5 cu ft or better sufficient for a household of 2. Maytag reputation for durability and reliability and made in US, though a clone of Whirlpool. These are big, heavy machines, best for side by side but they can be stacked. The units are quiet, have more features than weve ever used and so far have been reliable, gentle on clothes incl delicates and drum bearings really help with keeping loads balanced. Door hinges built like a tank but the chassis theyre attached to arent up to par. W & D have stainless drums. Washer is resistant to mold & odors but dryer lint system convoluted in design and hard to clean out.

I wish we would have never bought this brand and model. Within a month there was a loud banging and the serviceman came out and changed a valve out but it just got a little quieter but never went away. 2nd issue is cloths ball up when your doing bedding. Not sure if they are really clean or not. 3rd when we take the cloths out of the washer we are still seeing soap spots where they were not rinsed very well. We are using the right soap Gain but we cannot wash cloths in the bedding setting. We have to use the extra rinse setting to get all the soap out which defeats the whole savings issue of this machine. It says when you do your monthly machine cleaning it resets the water level but there never seems to be enough water in the tub. Also if your doing sheets in the washer and when the spin cycle starts you have to hold your breath to see if its going to get out of balance which it does 50% of the time so you stop and move things around. Also we cannot put a whole lot of cloths into this big drum because they dont wash correctly. Worst purchase we ever made. With all the negative reviews you would think that Maytag would come out with some fixes but I dont think they really care anymore.

We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

After 18 months of use Our Maytag Dishwasher (MDB7749) has the same control panel problem as a lot of other user complaints. I wish I too had read the consumer reviews before my purchase. We will never buy another Whirlpool product!!