2011 model MVWC2oox W1- spin dry failure - We purchased above top loader in 2011 and have had no issues until now. Currently constant failures on spinning and drying. Spin cycle stops without getting up to speed and appears to be an unbalanced load sensor problem. Also draining is not completed (possible pump going bad). Area tech came out within a week as promise and ran the diagnostics and found no faults. Problem has continued. We do a load a week. Looking for better answers or a new washer.

So I read the reviews when I bought this Maytag Bravo Washer and figured stuff happens. We bought the top load Maytag Brava in 2013. We bought the Home Depot warranty, 2 years later the washer was leaking water. 5 repair visits and 3 attempts to fix the leak before it was repaired. As of 4-25-17 the wash machine displayed un-level errors and started vibrating with a thundering noise. Called out warranty repair and they stated we need new bearings. Repair is scheduled in 2 days and now the wash machine is thundering and spewing oil so it is shut off. 4 years old, and like the other complaints clothes come out with dry patches and not clean. This is a bad machine, we are saving for our next washer. It will have an old style spindle/agitator, no California efficiency and probably not Maytag.

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

Maytag 7000 series front loaders bought in 2013 on basis of high ratings from Consumer Reports. Also durable and look good in the process. Had for 3 years. Machines highly rated by Consumer Reports and bought on sale. They were a very good value. Both W & D have steam feature but find Ive rarely used it. Durability is key, as is the ability to balance wide variety of loads, which our machines do well. Capacity of 5 cu ft or better sufficient for a household of 2. Maytag reputation for durability and reliability and made in US, though a clone of Whirlpool. These are big, heavy machines, best for side by side but they can be stacked. The units are quiet, have more features than weve ever used and so far have been reliable, gentle on clothes incl delicates and drum bearings really help with keeping loads balanced. Door hinges built like a tank but the chassis theyre attached to arent up to par. W & D have stainless drums. Washer is resistant to mold & odors but dryer lint system convoluted in design and hard to clean out.

I bought a washer and dryer a few months ago from Home Depot Maytag. My clothes do not come out wrinkle-free. They are very wrinkled, to the point where I have to iron the perma press. The dryer I just got rid of was 30 years old, and always got the wrinkles out of the clothes. So I am very disappointed in the way yours works. I dont know what you can do, but this is not good. Thank you.

My husband and I purchased the Maytag dishwasher model #MDB7609AWW2 in December 2010. July 2012, the control panel would not operate. I called Sears to schedule a repair appointment. (I did not have an extended warranty.) After reading review after review of complaints about Maytag and control panel issues and learning it is a very costly repair, I called Whirlpool which now owns Maytag. (Be advised, Maytag is not the quality product it once was). Reviews also indicate that the replaced control panels are failing within 6 months to a year and a half. After talking to a person in the Maytag/Whirlpool service department, he suggested some things to do: unplug power, unlock control panel, etc. He determined it was most likely the control panel that needed to be replaced. I asked how long a new panel would last informing him of the complaints Id read. All he would tell me was that I had the option to buy an extended warranty. We have decided not repair the dishwasher and will replace it with a non-Maytag and non-Whirlpool brand. I will never buy Maytag or any products made by Whirlpool again. For a major component of the dishwasher to last only a year and a half is unconscionable.

I purchased an expensive front-load washer and dryer a few years ago. About a year after I purchased the washer, there was a foul smell that developed. I contacted Maytag and they informed me of the directions to follow - keep the washer door open when not in use and use Affresh tablets periodically. I followed these directions and was unable to prevent the washer from developing mold in the washer. Id like to file a formal complaint on my washer and dryer. I want a refund on it. I paid way too much money on these units to suffer. Here are the details on my units: Maytag 5000 Series with steam 4.5 cu.ft., Maytag Commercial Technology, Model: MHWE550WW01, Serial: CS00202582, Type: 199-02 732 WT/CR, 12 amps, 120 volts, 60 hz.

I bought a new Maytag stove and it is less than two years old and the oven has already quit working. It only has a one year warranty and will cost about $200 to fix. I am very dissatisfied with what I thought was a good product.

Every day you hear a hissing noise and water leaks in from the vents and freezes. This builds up and water leaks on the floor. You have to chip the ice out or end up slipping and falling. This happened to me - Maytag was no help. Time for a lawsuit.

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

Also purchase the Maytag MMV405DS-1 over the stove microwave and in less than one year the light kept going out and the unit functions at no regular frequency. The unit is now out of warranty but service is coming to look at the problem again this week because we reported the problem within warranty. Maytag needs to be accountable for selling a lemon which I can only guess has a bad motherboard that they do not want to replace.

I purchased this washer... the Maytag Bravos. It is the worst clothes washing experience. I only use one cycle as the other cycles do not provide enough water to wet the clothes. It is a large capacity top loader. DONT DO IT!

The control (computer) stopped working. The Maytag Centennial washer would not turn off. I had to unplug it from the electrical outlet to get it to stop. The repairman had to replace the computer panel. He said it had burned up. I bought this machine from Lowes on January 11, 2011. It lasted 15 months and cost me $265 to get it repaired. I called Lowes and because I did not buy the extended warranty, they would not even talk to me. When I pay about $500 for a washing machine, I expect it to last longer than 15 months! I will never buy another Maytag appliance! Customers beware: these products are a bunch of junk. Even the repairman told me so.

I purchased my Maytag washer and dryer set from the Maytag store in Glendale, AZ in September 2005. I even bought the stands for them. With my purchase, I got the extended warranty for four more years. I didnt realize that I would really need it. I have had so many issues with the washer and dryer I cant even count - from the control panel not working, to the noise and the vibration when washing, or maybe in the smell of moldy cheese. I also have issues with the constant chimes of D5 code that keeps coming up on the display screen. After 2009, I finally gave up on calling the Maytag customer service folks to have someone come and service the washer because it was out of warranty. I just decided to live with all those issues.As far as my dryer goes, the rollers went bad and that was replaced. The burnt smell isnt so bad as long as you use a wire hanger with a sock on the end of it and clean the inside of the vent. Then try to vacuum it, take the sock, get it wet, and clean the inside of the vent again. This was the most expensive piece of junk I have ever purchased in my life (almost $3,000.00 with the stands and warranty).What really gets me upset is I had the Maytag people servicing my washer and dryer up until 2009 and no one told me about a recall of my washer and dryer. The only reason I found out about it was searching for the specs as the washer finally died and I am replacing it. Trust me. I will not be purchasing a Maytag. I know that Whirlpool purchased Maytag so I am not even going to consider Whirlpool either. Since Whirlpool purchased Maytag, Whirlpool should have contacted all Maytag consumers, (which they didnt), put ads in newspapers (which I did not see) or put an ad on TV. None of these appeared to have happened.By the way, when I bought my Maytag appliances, I was supposed to get a $200 rebate for buying the stands that never came. It must have gotten lost in the mail - as well as the Tide coupons for three years. You, guys, remember that too. I will never ever purchase a Maytag appliance or Whirlpool, since they own Maytag now.

I will never buy another energy efficient washer again. My Bravos is supposed to save money and be environment friendly, but when you have to wash clothes more than once to get them clean, theres no savings. Ive tried different detergents, cleaned the washer, rinsed twice, added vinegar, baking soda and everything imaginable to get the clothes smelling fresh without any luck. I have had several items ruined because the bleach dispenser pours onto dry laundry. Im disgusted.

Nice refrigerator, but cheaply made. I paid 1800 with tax for my french door Maytag and expected higher durability. It operates well but one worries about breaking drawers made of such thin plastic.

We recently purchased a Maytag Washer/Dryer set, but shortly after it arrived, we realized it was way too big for our needs, so traded it in for a smaller model (Model #MVWB765FC3). After a few washes, it developed a loud clicking noise during the entire wash cycle. Inquired about it at the retailer we purchased it from (showed them video of it) and was told it was not supposed to make that noise. Subsequently the Maytag Repairman paid us a visit and told us theres nothing wrong with the machine and that the retailer should not have told us what they did.#1). The machine did not make that noise initially. It started after a few loads of laundry. #2). The first machine we brought home was the same model (only larger) and that one didnt make that noise. To add insult to injury, the repairman has the audacity to tell my husband, Well, this visit didnt cost you anything. Really?! It cost him 4 hours of pay while he sat home waiting for you! In addition, we were delivered two cosmetically defective dryers that had to be returned. Furthermore, when I was washer/dryer shopping, I sent Maytags Customer Service Dept. an e-mail through their website asking questions about the product. To this day, I have still not received a response. I had a bad experience about 20 years ago with Maytag, but thought Id give them a second chance. I tell you...there will not be a 3rd time.

We bought a washer & dryer from Home Depot 2 1/2 years ago. The control board went out on my washer. I called Maytag and they wanted $109 for a diagnostic fee and wouldnt tell me how much the labor would be. A control board costs $350. So by the time all is said and done... the money would be better spent buying a new one. Maytags slogan of dependability lasts is a bunch of hooey. Washers should last more than 2 1/2 years and Maytag should back up their appliances. They just lost a customer.

We have had our Maytag double oven for about 5 years. 18 months ago two of the burner knobs froze off. You cannot turn them. We had oven repaired - they replaced part WPW 10204705 - it cost us approx. $400 to repair. Here we are today and ANOTHER burner know has frozen in the off position. I will have to pay again to have this repaired. We are super disappointed with this over and with Maytag. We would never purchase from them again.

The washer worked great for the first 6 months, then it didnt dissolve the soap, it wouldnt complete the cycle, and there is a loose bolt like sound when you spin the drum. The load level is not an issue. We have had the serviceman out four times, he has called the tech support each time and they cannot resolve the issue. Maytag said sorry! Unless it does it constantly then they cant help. The control panel has been replaced and the drum has been replaced. So we keep paying the water and sewer bill to rerun the load 1/2/3 times to get it to complete the cycle. This washer was purchased last May, 2011 and they say were stuck with it.

I have had 2 Geminis. The first one was fine, this second one is a mess. I have had at least half a dozen parts replaced. I have insurance to have this oven repaired but have paid to have the window seal replaced on at least 3 occasions. The top of the oven is so hot that when I have used the burners to cook on top I have received 2nd degree burns. I have received burns on several occasions. I asked dealer if I could trade this in but said I would have to sell it on my own. I would not subject this oven to another person as I feel it is very dangerous.

Oven is not even 2 yrs old but, the bottom oven floor lining is crackled & flaking. Although they say the cavity is covered under the 10 yr warranty, they say its not covered. Basically told me theres nothing they can do for it. I bought all Maytag appliances for my new home because they claim they stand behind their product. The 10 yr plaques on the appliances are a joke. So disappoint.

I have had Maytags for 20 years and never have been disappointed before I bought the Centennial and it is junk. It doesnt even put enough water in to wash the clothes. After it breaks, I will never buy Maytag again. When did you guys start going down the drain literally? My clothes do not get cleaned. I live in the country and we all get dirty. We need a dependable washer and dont even get me started on the dryer. I thought maybe you would care enough to know.

Seems a little ** one of a small child crawled into the washer and a sibling turned it on. We have been married 35 years and seen a lot of washers and this is by far the worst wash machine Ive ever seen. How would you rather do my wash in an old fashioned mangler? Very unsatisfied customer.

The brackets that make the door open and close are just screwed Into the plastic lining with no kind of anchors. If you use the freezer a lot the screws come loose. Can’t close the door. And then 300 dollars later a service call. All to replace a screw. That’s just fine but the hole is stripped because no one could install a 50 cent anchor on installation at the factory. No more Maytag for me.

I have a Maytag fridge (model # 2258VEM4) which I have had for 4 years. A few months ago, it started leaking water on the floor and notice that it had a bed of ice on the floor of the freezer. Reading the list of complaints in this site for the same issue, it sounds like it is a design problem.

I purchased top of the line Maytag washer and dryer in 1975! They are Harvest Gold. They were sold last week along with my house. I now have Whirlpool appliances in the rental apartment I moved to. There are some irritating features.

My Maytag refrigerator Model MFX2571XEMS has to constantly be defrosted due to ice accumulation in the bottom of the freezer. If not defrosted, water leaks out onto our hardwood floor. Maytag will not do anything to resolve this problem. We were told by a repairman that we have to defrost it manually to fix the problem. Yeah at least every 2 weeks. What a rip off.

I bought this washer from Lowes in 2013. It worked okay for a little while but lately it stops mid-cycle. Clothes are soaked and all of the soap hasnt been rinsed out. Poor excuse for a washing machine! Will never buy a Maytag again!

In October 2016 I purchased a New Maytag washer (Model# MVWC565FWO) from LOWES. I bought an extended 5 year warranty with it as well. I have my invalid, totally incapacitated Sister living with me. The situation requires several loads of washing each day due to her conditions. TWO WEEKS after starting to use it we began having issues with the washer. It would stop in the cycle, lights flashing, only way to restart is to unplug it, move control from wash cycles setting to drain and spin... then within the next 3-4 loads it would do it again. Sometimes it sat for awhile I would smell like an electronics Odor getting hot... I called Lowes. They replaced it. Approximately 3 weeks later the NEW washer began doing the SAME THING...Lowes would not replace it with a different Model or brand... only send a repairman out. Long story short, he has been here 4 times, replaced the Computer Control with NO IMPROVEMENT!!! NOW Lowes is sending him out again and saying that if this doesnt fix the problem they will refund my money... My problem with it all is this... IF MAYTAG is having these type issues, WHY PRAY TELL, has a recall or solution been found and passed on to the repair folks??? I bought this Maytag due to #1 Reputation, #2 It was Assembled in the USA, NOT South Korea like the Samsung with recalls... Now all this is going on. I WANT A WASHING MACHINE THAT WORKS RIGHT!!! This is totally unacceptable and totally uncalled for. WHY could these Govt agencies and Manufacturers not LEAVE the washers alone? Computer technology... PLTTT. The old timers controls gave no problem in over 40 years of using them. Now this crap.

We purchased a full house of Maytag appliances to support American Made (ourselves). It is very disappointing that our Maytag dishwasher Model # MBD 89595BW3 has completely quit functioning properly. All the lights came on and nothing worked after that. We contacted Maytag and was told to turn off the power and restart after 2 minutes which did absolutely nothing. No problem - try again. Again, nothing. The disappointment is compounded by the fact that this dishwasher is only 2 years 7 months old. It is too bad that an American Made product didnt last long enough to show any wear and tear. Investigation to repair resulted in cost prohibitive investment. So sorry Maytag, we gave it a shot. Moving on to a more reliable rated brand.

Our bottom freezer began building up ice. We cleared the ice and unclogged the drain gasket as per the many instructions that we found online. Researching this problem, I discovered very quickly that this is due to a faulty design of the drain grommet. A new part has been substituted by Maytag. I called Maytag customer service and they refused to supply the replacement at no cost to me and claimed there is no quality issue. This is not about the $20 for the part. It is a leading consumer brand disregarding customer satisfaction. This is also bad business. They will sacrifice their reputation for a $20 part on a $1,000+ purchase. They need to be put on notice that they cannot get away with this in the age of the web where there is total transparency.

My stove is approximately nine years old. During the past year both my husband and I enjoy cooking from recipes 3-4 times a week thus the stove has become essential. Functionality and size is important when trying to cook meals with two or three components. One of the oven racks was missing from the oven when we moved into the house. Even though it is self cleaning, spills pile up between cleanings so it is great that it has a really cool steam cleaning option. Just wish it were 5-6 years newer.

We were delighted with our new Maytag refrigerator, model #MBF2258XEB, until the compressor died less than a year after we bought it. Home Depot, where we purchased it, directed us to the A&E Company for service. Two weeks later, we are still without refrigeration; Maytag refuses to replace it and even refused to overnight the new compressor. We thought Maytag set an industry standard for excellence. Don’t buy this product if you want a reliable refrigerator from a company that stands behind its products.

I purchased a Maytag MDB7749AWM model dishwasher in March of 2012 for approximately $600. Fifteen months later, the control panel has gone out on it. From what I understand, this problem happens so often that its not even worth repairing this dishwasher.

We purchased a Maytag front load washer in May 2006 (MAH6700AWW). In November 2012 we had a leak and called a repair service. We were told it was the dispensing hose which had a hole worn in it and was replaced. In February 2014, we called the same service and was told that we had the same problem. Now in November 2014 we are experiencing the same problem. We have notified Whirlpool of this problem and each time were told that the machine was too old to reimburse us in any way. Guess who wont be buying any Whirlpool products if they do not back up their faulty workmanship.

I purchased a Maytag dishwasher model #MDB6769AWB2. After 1 year and 2 months of light use (just my wife and myself), the control panel went out on it! I called Maytag and because it was over 1 year old, they would not do anything about it! When you call their number listed in the owner’s manual, they thank you for calling their Customer Experience Center. This is an experience I can do without!

From day one I didnt like how this machine restricted how I can wash my clothing. There is no water volume controller. It is all automatic, which sounded fine in the store, but once I used it I quickly realized it is horrible. I can not add extra laundry or detergent in at the last minute because it says not to open the lid at all once you start the load. The settings are very glitchy. They do not seem consistent. There is a knob for level of soil on the clothing which doesnt seem to do anything at all. Ive had it now for four years and it has only gotten worse. Now I can only use one setting Hand Wash. Try doing a teenage boys clothes in Hand Wash and youll find out quickly that nothing gets clean that way. Oh, and all of the sudden the spin cycles are not working, they spin when they want to but they rarely get rid of the dirty water. Spinning in dirty water does not get clothes clean either. This machine is horrible, hands down, the worst washing machine I have ever owned.

Maytag dishwasher model #MDB7609AWB2 - The control panel on this dishwasher has just gone out for the fifth time since 12/10. Last time I also had to replace the control board also.

We bought a Model MDB7749AWB2 dishwasher 3 years ago. The first year the panel went out one week after the warranty wore off. They replaced it then and now two years, here we go again. Dont replace the part. I am not ever buying another Maytag again.

I have had this washer 4 years...I bought this washer in May 2016. It makes 3 very loud noise as it moves into its next mode/cycle. Found out this is normal. IF, it is close to your living room, IT is loud.. I called again, saw that it was not filling up. 1/5/2017.. IT will NOT fill up to wash my clothes properly, clothes were still dry!!! Came out, (they sent a company near my area), said everything is right. I have tried, by sending messages, many times to get them to check. No one seems to care. The machine allows water to go out the bottom, rather than fill in the machine. I watched it myself. THERE should be a recall on this machine, definitely, something is sooo wrong.. I NOW have to put it on BULKY SHEETS full time, to get my wash clean.. NO energy savings there... BUT my clothes are finally clean!! Seriously, something is wrong...

Bought this washer and dryer 3 1/2 years ago mainly because of Maytag name and reputation. They were very expensive to purchase. The washer is a piece of junk 3 1/2 years old used for my wife and I and leaks oil all over the floor. Called repair man to come and look at it, wasnt here 5 minutes said transmission is shot. Cost over $400 to have it repaired. We are junking it and that will be the last Maytag product I ever own.

This washer stops every 10 minutes, sometimes taking 3 to 4 hours to complete one spin cycle if it is completed at all. All troubles began shortly after warranty expired. NEVER EVER will I ever buy Maytag again. I make certain that I tell everyone I come in contact with about the pathetic quality of Maytag.

Maytag wall oven Model# MEW7530AB01 - We ordered this oven from Home Depot on Aug. 28/13. It was delivered on Sept.7/13. After a self clean cycle, the oven failed on Sept. 24/13. It was repaired on Oct. 23/13. Parts come from U.S. Im in Canada. Part # W10545255. It hadnt cleaned completely so I used the self clean mode again on Oct. 24/13. Oven failed. Fixed again on Nov. 15/13. Same part. Tested self clean again. Oven failed. Repairman fixed a different part. Thermostat #4449751. Oven still not working, had to order the front fuse again. Part # W10545255. Fixed Nov.19/13. Failed again Nov. 19/13. After not having a working oven for so long, Maytag finally agreed to send a new one. It arrived Dec.5/13. Tried cleaning cycle just to make sure. Oven failed. Same part. Called Maytag, told them I just wanted my money back. They refused. They would only repair. I agreed to have a repairman from another company come out. I told Maytag what part it was. They sent the repairman out on Dec. 19/13 with the wrong part. I called Home Depot a second time. I had called them after I talked to Maytag. This time Home Depot said they would take back the oven once it was repaired and I could have a store credit towards another brand. The repairman fixed the oven on Jan.9/14. Home Depot picked up the oven and replaced it with a GE and I love it.The part failing is a fuse in the top of the oven right at the front. Both repairman noted that a lot of heat is in this area during a self clean. When two ovens are having the same problem, I come to the conclusion that it is a design flaw and should be recalled. I only talked to one person at Maytag who was polite on the phone. That was the woman that got me the new oven. Everyone else was rude and hostile. I was even asked why I would clean a new oven. My experience was not a pleasant one at all. I wont be buying any products made buy the Whirlpool Corp. again.

The stovetop is very hard to clean and gets stained easily. The heat works wonderfully and the burners are great sizes. The left side with the adjoining burners is great. The double oven is fantastic. Heats relatively fast. Another negative is the button controls. You have to push so hard for it to register. Its painful. Not the best way to do it. Just setting oven temperature is difficult. Wish that was different.

Hate my Maytag Centennial Commercial Technology washer. It takes well over an hour per load. Clothes come out very wrinkled, and my knits get holes very quickly. I would not recommend this machine to anyone. In fact, I warn people against it as I have been frustrated every single time Ive used it. Model # W10420382A.

I purchased a Bravos washing machine 3 years, 9 months ago. It has stopped working, bad bearings. How can a major appliance fail after three years for bad bearings unless the bearing were bad to begin with??? The repair man knew by the sound the problem was bad bearings. The washing machine sounded the same as it always had, which means the bearing were bad from the start. My first washing machine, a Kenmore, lasted 21 years and a few months. How can you produce such a terrible product and expect I as a consumer would buy another Maytag product or recommend a Maytag product? Not to mention what will now enter a landfill someplace, terrible!

The $1,100 Maytag Bravo XL does not have a dedicated spin cycle. Its rinse and spin. When out of balance, you rearrange and it rinses AGAIN - 15 minutes - before you know whether its balanced. By rinsing again, it can redistribute to be out of balance. Repairmen (w/ extra warranty) said you cant wash bath mats, bedspreads or pillows though it had giant capacity! They would charge me if I called again about it (3 strikes). So bought a used Kenmore with no computer panel... Its great! My dealer had the Maytag hauled to a dump, he would not sell it to anybody as he had integrity.

The first problem happened a month after we bought the horrible product. I had biscuits baking in the oven and the oven door locked itself like when in self-clean mode. Maytag sent out a repairman that had the part in his truck because they knew there was a problem with that models door. I pointed out that the door does not shut properly, causing inaccurate heating and scorching on the outside of the oven door. The repairman insisted that it was shut properly, and that it was designed at the angle the door sits. He replaced the scorched part of the door, but it immediately scorched again. I have had the part replaced 3 times, and will not do so again until we sell the house. I have spent over money over and over again to make the repair, because it makes the stove look like it is filthy with grease. Now, all the dots painted on the glass top are coming off, and the remaining black glass behind it also looks like burnt grease. It is so embarrassing when entertaining; but the stove is clean. I spent a lot of money for this, and it has been junk from day one. Avoid purchasing.

My Maytag refrigerator has driven us up the hill and back and has taken us several months in order for us to get the issue solved. This is quite an expensive fridge freezer and the after service has been diabolical to say the least. All their service calls in the UK were handled by a third party and it seems that there is some sort of change of ownership between Whirlpool and Hotpoint so after all the previous visits by different companies the problem of water leaking unto our floor is still going on and now all their call are being routed through a major insurance and a utility company who are more interested in trying to signing you up on one of their insurance policies than fixing it.To make matters worse the contractors they use are absolutely useless when it comes to fixing american style refrigerators. I was told I needed various parts which would have cost hundreds of pounds or that the appliance was uneconomical to repair. All of which was untrue. This I later found out when after emails after emails Whirlpool passed on the contact details of a service agent ags refrigeration who came out and found that there was a fault with the water in line connector at the bottom of the refrigerator which they replaced.

I purchased this five-burner gas stove two years ago. I have this stove repaired three times. The first and second problem with the stove is when I turned on the oven, it would never click on. This was a month after I purchased the stove. They sent someone over to correct the problem and that did not work. The third time someone came. He changed something in the oven and it started to work. After that, I continue to have trouble with the oven. When I have the top eyes on, the oven will not work. When I only turn on the oven, it will go to 350 only. It will cook for an half hour and then cut off. I smell gas in my house and my food is smelling like gas. I have stop using the oven. I did not purchase a stove to not use the oven. This is totally ridiculous!!! I am tired of this situation. Maytag needs to recall these ovens, so I can purchase an oven that works. I have thrown food away because it smells like gas - because the oven will cut off in the middle of cooking. I am very tired of this situation and when you call Maytag, their customer service is terrible. I will never buy Maytags products again. Please help.

Absolutely the worst washer I’ve ever had! Do not buy this washer. Even after a double rinse there is white matter left all over everything! I’ve taken photographs of my laundry after two rinses and it’s disgusting. I will be quite happy to submit the photographs at any time.

I have a 26 cu. ft. side by side Model MZD2665HES, like most folks in my neighborhood (spec homes). The icemaker died and service was called. They looked at solenoid, and replaced the ice maker assembly as a wag that it was the problem.. still no ice, but the water was still able to be called. I replaced filter- still water only, no ice. Little did we know it was the filler tube blocked with ice, and the service man didnt once suggest turning off the water service. SO, every time water was called to either make ice or to fill a cup with, it put intense pressure on the point of assembly where the water line comes into the fridge (water inlet tube). A pin hole developed in the little plastic bit (water inlet tube plate) and every time the water was called to ice, guess what happened - it shot right out the back on drywall.Almost $20,000 dollars worth of damage to wood floor (warped), drywall (jello), and flooring (carpet) ensued. Mold was all over and had to be contained and treated for days to be fixed. Im still duking it out with service repairman and insurance companies. My advise: If you have this fridge or anything like it and the ice maker stops working, IMMEDIATELY shut down the water supply, turn the fridge off and check the filler tube in the back for ice blockage. Probably a good idea to pull the fridge forward once in a while and check the back for water also.

Same thing as everyone else. The motherboard/control board, the main face of the washer went out and this part isnt covered on an $800 commercial washer after only 3 years of residential use on a commercial washer. Menards refused to swap it out, saying this is Maytags issue. Maytag boasts their 10 year warranty and labels it right on the motherboard as a 10 year warranty, but the motherboard isnt covered? If the main computer isnt covered, What is covered? Just screws? I called Menards and got nowhere. Called Maytag and held for an hour then had to hang up so I can work. The warranty is extremely misleading and is the reason we bought this particular washer, because it says 10 year parts warranty right there, but Maytag conveniently doesnt consider the main control board a part.

Purchase a Maytag Bravo XL Washer Model MVWB850YWO from a major Home Improvement store in January 2012 with a 4 year service plan. Since this time I had to replace a motor and 4 (that is right 4) control panels. Although I am covered under a protection plan, the cost of laundry services and an outage of 2 weeks for each event is very costly. This time I call Maytag for support on their product. Looking for someone to say that there is something wrong with this machine. I want to hear that their product should not perform like this. I was told from a supervisor in these words that Mrs. we only care about the machine the 1st year. After that you are on your own. When did Customer Service lose the service part? When did companies stop caring about their products they produce? I never heard I am sorry youre having trouble or even a recommendation. A machine this new should not have 4 control panels replaced. This is the reason no one wants to buy a Made in the USA product anymore because we know the employees working there do not care about keeping customer relations.

Have had continual problems with Maytag Bravos. They will replace in under a 5 year warranty. If not for the warranty, I would be out over 700 dollars spent on this very bad machine. Based on my experience Maytag washers are of poor quality. I would stay away.

I bought the Maytag Bravos XL 5.3 washer because it was advertised to conserve water and it was a good brand, but it was a horrible mistake to buy this washer. The washer barely uses any water to clean properly and it hardly moves any of the clothing. The only thing that does move is the clothes at the bottom while the clothes on the top stays still. After using it for a day, I decided to return it back to Home Depot where I bought it, but they did not accept it and told me to call Maytag to return it. I called and the person who answered gave me different numbers to call. After going through ten different numbers, I finally received someone that could help me and they told me that I could not return the washer. They told me that the only way to return it was if there was a mechanical problem with the washer. It is extremely frustrating because I paid over $800 on this washer and now Im stuck with this garbage because I cant return it. I recommend everyone to not buy this washer otherwise youll get the same problems I am getting. I have to manually stop the washer and move the clothes by hand.

I purchased a Maytag dishwasher (Model No. MDB8949SBWO) in September of 2013. Within the first year (and under warranty) the control module failed. The dishwasher is now almost two years old and the second control module has failed. From other postings it is obvious that Maytag has a known defect in their control units. To replace control modules on an annual basis makes this an extremely expensive dishwasher to own.

I am sorry I purchased this machine. It was meant to replace a 17-year-old Maytag dishwasher that was not repairable. I figured they were good machines. Wrong. Perhaps I have a lemon, I do not know. I bought the machine on the 23rd of November and it was installed on the 29th of November. Here it is December 12th and I am sick to my stomach. I have already had to contact Maytag customer support and have a repairman coming. This machine does not clean worth a damn! My glasses look worse coming out of the machine than when they went in. I have run two loads with the machine so far. The auto-sense cycle is a joke. It took over four hours to complete and things did not come out clean. Last night I tried the normal cycle. It came up with a run time of 2:36. The first rinse was cold water. The detergent cup was open and empty at 20 minutes in. So what does the machine do for the next two hours??? When the cycle was finished I looked at the glasses and they were spotted and streaked with remnants of fingerprints and lips. So I ran it again trying the quick cycle. Not one bit of difference, still nasty looking glasses. If this machine cannot get the upper rack clean, how can I be sure the lower rack is getting sufficient cleaning? One would think that for $600 it could at least do the job it was meant to do.

So far after 5 calls and over two hours spent on calls IMPOSSIBLE to get an answer from Maytag about the correct fill levels of detergent. Consumer support simply do not know and refuse to direct me to anyone or have anyone call that does know answer. WHY SO IMPORTANT? Either you do not get clothes clean OR you damage machine and leave residue on clothes! Neither is acceptable. Using the fill level indicator on Bravos XL dispenser is in direct contradiction to any recommended levels on lids of high efficiency detergent manufacturers like Tide. Per Maytag manual only fill detergent to max fill LINE which is literally about two or three tablespoons of detergent. The lowest possible quantity of Tide per the lines on lid even for smallest load is two or three times the recommended fill level on the dispenser. No one has to be an engineer to know two tablespoons of HE detergent in dispense is going to do same effective cleaning for one shirt or towel as it will with a queen size comforter or very large full capacity load. CORRECT ANSWER DETERMINES IF YOU DAMAGE WASHER OR IF YOU HAVE DIRTY CLOTHES. Googling online there is also no answer. Such a critical answer for Maytag washer to work and clean clothes that is simply not available and documentation is wrong is a huge concern about the viability of this machine and worse their support. Our machine is less than two months old but is obviously over-engineered to the point of just being silly. Tip to Maytag: start selling washboards. More energy efficient, more green except for red and blue bruised knuckles, uses one tenth as much water and users do not need to spend their nest egg savings to buy. Not the first but will be the last Maytag product we will buy. Name may be same but the company is definitely not the company that used to enjoy that name with pride. SUMMARY: Maytag is adamant about using the correct amount of HE detergent OR damage and bad performance by washer and dirty clothes with a detergent residue. With all our best efforts we cannot get what that quantity of detergents is supposed to be. The user manual at best has ambiguous answer. The manual suggest horizontal measure of detergent in tray to max fill level which cannot be right. IF you instead use a vertical measure of how high detergent level comes up to the max fill line the quantity is radically different. It says dispenser holds 3 oz which would be beyond max fill level but nowhere near a vertical fill level.

Bravo XL - This is the worst washing machine I have ever purchased! Loved it at first but after a year or so we couldnt wash a full load without error messages. Then we couldnt even wash one pair of jeans without an error message. Called to have it repaired and $300. Later the bearing was replaced and the washer worked wonderfully once again. Less than a year later and we are back to having a non functional washer. Cannot wash anything without the error message. Customer service is absolutely no help. For such an expensive washer and supposedly a good brand, this machine is a real disappointment.

Maytag Bravos electric steam dryer purchased 2009 - I have had to replace the door hinges within one year of usage at my expense. The blower belt and pulley had come off twice, the last time about a half hour after the repairman (again at my expense) left. I put it back on myself and if it comes off again, I will use Locktite to glue it on the blower shaft. I figure I will be lucky if this crap lasts a couple more years anyway. No more Maytag for us! What does it take for the consumer to get some representation with regard to lemon laws here? I will take my wrath out on Home Depot here since I have no recourse. If enough people complain, maybe they will stop selling that junk. I also will disregard Consumer Reports in the future.

I have always used Maytag products at home and work. I have never had a problem like this one. The front load washers have a manufacture default with the boot that allows mold to grow even when it is wiped out as instructed. I have contacted other people and they have the same problem. I will not or ever buy a front load Maytag again and could never recommend this product to anyone. I feel that the Maytag company should replace the boot with a different design; at no cost to the consumer! This machine was only a year old. I have no problem with the company I bought it from. They replaced the boot with a bill of $358.65.

My dishwasher like many others have mentioned is experiencing the same control panel issues. When I set it to Wash, it spontaneously goes to Rinse Only. I am unsure exactly the age, but given the number of complaints Ive read, with the same problem, it seems as though, there was a flaw many years ago in design and regardless of issues hasnt been resolved with the newer models either. I realize appliances dont last forever, but Maytag was always known for the lonely repairmen and Id hoped the brand would continue to live up to its advertising, despite being purchased by Whirlpool.

Fifteen months after purchase, the lid lock and motherboard goes off. It was replaced with new parts and the machine still doesnt work. Cost of repair is equal to the cost of the machine. With or without an extended warranty, the expense is not worth the investment. While shopping to replace the machine, the dealer finished my sentences on Maytag washers.

Very disappointed with Maytag Bravos XL, four year old unit with bearings going out. Quoted $400 + for repair. With two in the house, wash demands are normal. Quality is questionable to have bearings & seal going out in four years. Also you cannot buy the bolt which holds the Washer Motor Rotor Cover on without buying the whole $130 assembly. Daughter has Whirlpool brand with same problem. Seems to me this is a problem Maytag/Whirlpool should address. My old unit (that I wish I still had), worked for 25 years. Would not recommend these machines.

I am not dissatisfied with hhgregg, but with Maytag products. I purchased the Maytag Centennial Top Load Washer and Maytag Centennial Dryer to match. I was a bit leery of the new energy star models that use he only type detergent, but decided that was the newest and greatest thing out, so how could it be wrong? For the past two months, I have been sooooo very disappointed in Maytag. Neither of these brand new machines are worthy of being considered brand new. The washer takes extremely too long to wash a normal load, too noisy, and has ruined several items of clothing, due to malfunctioning distribution of bleach, fabric softener released after clothes are through washing. There has also been several times that the load wash is complete and the clothes are not even wet (like they were never involved in a wash cycle). As for the dryer, you have to run it through two 40 minutes cycles to get the load of clothes completely dry, so much for energy-saving. This is my first complaint to anyone, but after reading several reviews on Maytags website, I am reassured I am not alone. There are hundreds of other dissatisfied consumers of this Maytag product. I will be writing a letter to Maytag, requesting a refund.

I had noticed the lights, such as for sanitizing cycle, hot water cycle, etc, would go out intermittently, but since the washer still ran, I was down with that. Loaded it up last Sunday, pressed the button to start and El Zippo. Nothing works. So here we go again with another crap product from Maytag. Yes, I have had this dishwasher, which was a pricier model but closeout priced, at Lowes in 2008, BUT I live alone, so how many dishes do I wash. At the same time this is the third time had a repairman out (with no help from Maytag other than trying to sell me an extended warranty for nearly $400) and these machines ought to last a lot longer than this. The part online is bad enough, $150, cant wait for the repairman to call me back tomorrow and see how much they are going to hose me for.

My first job was at Sears but went elsewhere to buy Maytag. I have had only 3 sets of washer/Dryer in 50 years. The set I have now are over 20 years old! I am looking at a Maytag refrigerator now.

We have had 2 Maytag dishwashers only last less than 2 years. Since we can only have a portable because of owning an older home the expense is too much anymore. We also had a Maytag Neptune clothes washer last only 2 1/2 years. We had always respected Maytag and trusted them. That trust is gone. It is too expensive to buy and lose them after barely 1 1/2 years. We had a Kenmore that lasted 23 years. I dont know what company to trust anymore. The one we just had quit working a month ago was purchased October 3013. Maytag dishwasher Model #MCD4809PAW2 Serial #F34003436.

#Mgt8885x500 Maytag Gemini. After oven heats up, racks fall. What should I do. This is a safety issue. Help, afraid to use oven.

We bought a bottom freezer Maytag refrigerator a little over a year ago and have nothing but problems with it. It leaks and has ruined my hardwood floors. The lift lid for the meat and cheese broke. I have had other refrigerators with kids at home for 10-12 years and never had these problems. It is just my husband and me now so I know it does not get the abuse other refrigerator that were different brands received. I would never buy another Maytag refrigerator. I have been so disappointed with the product and the service. I read some other reviews and have to agree that Maytag could care less about their customers. I have also received several Im sorry, but basically we cannot help you.

Maytag Dishwasher MDB8959AWS6, S#F15006566 purchased 12/28/2011. Here is a record of the product repairs done by All Tech Appliance Service in Portland. 1/12/2014 - Thermal Fuse and Control Board. 10/15/2015 - Thermal Fuse. 9/2/2015 - Thermal Fuse. 12/5/2015 - Unit stopped working again, strong electrical smell, probably Thermal Fuse again. This dishwasher product has a design defect. It should be recalled.

I recently purchased a Maytag French door, bottom freezer. It was delivered and set up by delivery men and when they pulled out the bottom freezer the bin and tray were missing. This refrig should have never been shipped (per Home Depot) and also delivery men. They called Maytag and ordered the missing part. 5 days later it arrives and is not the right bin. I purchased the 5 year warranty contract and after calling 3 numbers and getting shuffled around, they told me it should also have a slide out. They set up appt. for this Thurs. I wanted to file a claim for loss freezer meat and was told Miss, your 5 year warranty does not start until the 1 year manufacturer warranty is up. She also proceeded to tell me that no refund will be issued and they are NOT responsible when their product leaves their plant and gets to me. REALLY... The refrigerator was not properly inspected and still shipped. Not covered under warranty and fridge is 5 days old and have had issues from date of delivery. I will never make another purchase of a MAYTAG and their customer service could use more training and a course is representing their company in a much better way.

Purchased this washing machine 4 years ago and every time I do towels, blankets, linens etc. all ends up in the middle of the washer in an unbalanced situation. Cannot clear the balance even when rearranged. I assume this is what happens with all the upright washers now that the center agitation unit has been removed. I have to ask the question of who made this decision to remove the center part? A man who never does laundry?

Purchased a Maytag Dryer, Washer and Oven Range in December 2011. Both washer and oven were serviced within 1 year under warranty. The dryer stopped working in August 2013, not under warranty. Total cost to repair is $450. Called Maytag to see if they could reduce the repair cost, answer... NO. Maytag spends millions of dollars in advertising... Built Strong to Last Long but they cant spend several hundreds to keep customers. Will never buy a Maytag, Whirlpool, KitchenAid or any other related company product ever. Their motto should be Built Weak to Last Weeks.

We bought our $600 Maytag dishwasher less than two years ago and have had three separate problems with it, from faulty instillation, to a faulty seal to faulty control panel. The first problem was covered under warranty, the second problem we fixed ourselves and the third problem, nothing can be done except pay an additional fee of $250+ for a new part. Maytag used to be a good name but with three problems in under two years, the only guarantee given is that if you buy one, be prepared for problems. This company does not stand by their products and will only ask for more money to fix their faulty items.

I purchased a Maytag Dishwasher April 6th, 2011. Its only 3 years old and now the control panel isnt working properly. Specifically, the start button. Contacted Maytag Customer Care service and they could not help me other than charging $80.00 for the Maytag Man.. which by the way, we arent suppose to see because of their superb quality in appliances. So I have a repairman scheduled for next week. I am an highly dissatisfied customer because the dishwasher is used once a week for the 3 years Ive owned it. Just a poor quality product which I will never purchase again. Model #MDB7609AWB3 Serial # F10202246.

Front load washer is four years old. Approximately two years after owning the washing machine it started burning and ripping our clothes. Maytag sent someone out to repair at no cost. The problem stopped. However, approximately two years later it is happening all over again. Thus, there is either a deficiency in the Maytag product or the repair has failed. Maytag will only repair at our cost. True, the washer is four years old but the same problem keeps happening. Plus, that is not a long time in the life of a washing machine. The customer should not be held responsible for a recurring problem with their product. The front load washer and dryer were very expensive. We will NEVER buy Maytag and we will continue to share our disappointment to whoever will listen. It is shameful that Maytag says they stand by their product but when its put to the test Maytag completely fail. Double thumbs down for Maytag and customer service!!!

I purchased a Maytag Epic Z Front Load Washer less than 5 years ago, and there is only 1 person in my household. I replaced a part that the technician said was bad for $300 and that didnt work, so they replaced another part for another$ 200. Then, when that didnt work, Whirlpool deemed my washer irreparable, and they will not stand behind their product. This is totally unacceptable, and I will never buy another Whirlpool product. I will also tell others that they do not stand behind their product. If this was a 20 year old product, I would understand but it is not typical for something like this to happen.

Bought a Maytag washer MVWC415EW in 4/2015. We dont use the washer heavily but over that time span the paint on the top cover and the side where the cover comes down has bubbled up. It looks like a bad rash but only on a washer. I think the company used inferior paint which can bubble up with the heat of the hot water during the wash cycle. I called the company but they do not cover cosmetic items on the warranty. I think since this was a flaw in the paint used they should at least replace the cover portion which would be an easy fix. Maytags are not what they use be! Last Maytag lasted 17 years with no paint problems or mechanical problems.

We have the 4000 series front loader washer. Within 8 months of owning it, it would shut off in mid cycle. You have to unplug it to restart it. Then, when it completes the cycle, it is still soaking wet. So, you have to put it through the drain and spin cycle again. There is something major wrong with the spin cycle. It takes about 2 hours to do one load of laundry and you have to stay home to do all of the steps. It costs as much to fix it as the machine costs. It’s the worst washer we have ever had. No more Maytags!

Purchased washing machine, with insurance that was offered to me 9/17/10. May 2013, control panel went. June 2013, dial switch went. July 2014 washer motor drive & belt drive had to be replaced. August 2015 is broke again. Will never buy Maytag again.

I can’t seem to get any help with my dryer. I have replaced the drum 2 times and thermostat 3 times. Model number is mde9700ayw. Serial number is 13229569gp. I simply want a new dryer that works.

I bought this stove thinking of the Maytag repair man commercial that was advertised on TV for washing machines. Apparently Maytag only knows how to make washing machines (I did not buy one of their washing machines after my experiments with their stove). From day one the oven door never closed right, the self cleaning oven device had to be replaced 3 times over the year after have a repairman tell me that they all fail. I stopped using the self cleaning feature. This stove has cost me so much in repairs. The cook top is very very hard to clean. It always looks dirty. All the plastic knobs have melted off because the oven door never closed right. And the knobs are crazy expensive to replace as is just about everything on this stove. The oven temperature can not be trusted never cooked at the temperature it was set at. I paid a lot of money for this stove 10 years ago. And I am finally able to replace it thanks to a Christmas present from my 3 children. I love to cook and this stove made it difficult. My advice is to look for a different company when buying a kitchen stove. This Maytag has been nothing but trouble for me.

Please save your money and do not purchase a the Bravos XL MCT Washer and Dryer! I am sickened by the fact that I spent $1,800 on the biggest pieces of junk there ever was. Youd think a company like Maytag would be able to build a product that worked properly. We are getting ready for our FIFTH visit by a service repair company that will only plug in their computers and say nothing is wrong. Well here is what is wrong: Washer does not rinse all of the soap and I have many, MANY, pieces of dark clothing that are ruined because of the white streaks all over. I have done EVERYTHING the service guys have said to do; use less soap; use the deep water wash cycle, etc. etc. There are only two of us in the household so my average load size fills the EXTRA LARGE drum maybe half full so all their advice hasnt worked. It does not rinse the water out of a load of towels (remember there are only two us so not that many towels) and I have to run it through a rinse and spin cycle. Waste of time, energy, AND money. I washed a single coverlet and had to run it through a rinse and spin cycle twice to get the water out! If you use the bedding cycle, it runs for 90 minutes and still doesnt spin all the water out! The dryer is not better either. On average, it takes one hour and ten minutes to dry 3 bath towels, a couple of hand towels and a wash cloth. One of the service people that came out, checked our dryer vent and said everything was hooked up correctly. Talk about a waste of energy!! I would do anything to get rid of these pieces of junk but we spent so much money on them Im stuck until I win the lotto or something! I cannot stress enough that you will be wasting your money if you buy any washer and/or dryer product from Maytag! Believe me, I regret it every day!

I purchased this Maytag Bravos XL Washing Machine at Lowes in California, MD for about $800 on April 8, 2018. What a disappointment for a Made in America product! BUYER BEWARE - DO NOT BUY! I agree 100% with the reviews and comments. This washing machine is a PIECE OF JUNK! It does not clean clothes! It does not provide enough water to get all clothes wet! All it does is shake the clothes back and forth and stays in the same order you put the clothes in. I agree with one of the reviews that it does nothing but crumple/wad the middle items together and rub them. And the clothes are DIRTY!! I will be calling Maytag 1-800-344-1274 and demand for my money back!! Lowes should STOP selling this product!

I bought the top of the line Maytag washer. I was told they have improved their washer so that it no longer requires an agitator. I was also told the new machine saves you money by using less water. It has a sensor so that it only puts the water needed to clean your clothes. Instead of filling up with water and having the agitator to stir the clothes around, this new and improved machine puts a small amount of water in the machine and vibrates. The end result? All of the dirt and debris gathers in small pockets and sticks to your clothes. In order to save water the sensor only allows a small amount of water to enter the machine to rinse your clothes. When you consider how many times you have to go back and rinse your clothes before you get the caked on dirt off of your clothes, its costing you more money, more time and more aggravation. Oh yea, the maintenance man was out three times before the machine was a year old. The last visit was to replace that fine Maytag motor that was less than a year old. I have pictures that show my clothes with caked on dirt and debris on them after they have completed their wash cycle. It is HORRIBLE!!!

We purchased this Maytag Centennial washer in 2009 (model # mvwc6esw/Wd; type 849-05; ser # cy1741855) and I have hated it ever since. I had an old 406 Maytag washer that was worth its weight in gold - repaired it as long as possible. I bought this new one because it was a Maytag and that was a mistake. The way it agitates my clothes get tangled and they never did that in the other original Maytag. We had to have it fixed not long after we got it and now every time I turn it on, it immediately starts to agitate on every cycle except hand wash, which it never did before. If I knew it agitated the way it did, I never would have got it. Good thing we bought an extended warranty for this machine. We have used it once already and it looks like we may have to use it again. I am very disappointed in this machine and your workmanship. The old machines were much better and more dependable.

Maytag Dishwasher, mdb7749sam1 - I got this dishwasher new in Feb. 2013 for my new house. I thought that Maytag was supposed to be a very good appliance company. (I just found out that Whirlpool bought them! I dont like their dishwashers, either! Ive had 3 whirlpools that only lasted about 2-4 years each.) My dishwasher worked great until the control panel buttons started blinking and going crazy! Then, it just stopped working altogether. I called Maytag about this part, and found out that it is only covered the first year, and the so-called 10-year warranty doesnt cover it. What good is the extended 10-year warranty if it doesnt cover all the parts!? I researched this dishwasher before I bought it. It got fairly good reviews at the time. Now when I look it up, it gets these terrible reviews! I am so disappointed with this situation. I have other Maytag appliances that have performed great. Im not sure why their dishwashers cant be made the same way.I am going to order the part and repair the machine. I hope this will fix the problem. I had hoped that the Maytag brand would live up to their hype, and be better than the Whirlpools I had already had such bad experiences with. The Whirlpools had great features, they just didnt last! This dishwasher, too, has great features. Two years isnt a long enough run for it to be a good choice, though. Really disappointed :(

My dishwasher, purchased in 2013 sings the same tune as many of these complaints...stopped working correctly, turned on whenever it wanted to, etc. Thought it was the cpu...no. Called Whirlpool and they gave me the same runaround that they give everyone...more money for a temporary fix. Did some more research that led me here and discovered that the ribbon cable leading to the control panel was fried due to heat and moisture. Easy to check for yourself... looks like brown crap on the cable...if you have a meter, you can easily check it. Tried to repair it, very difficult, but I tried. NEWS?...I wrote a complaint to the Better Business B... and mentioned that this is a safety issue, which it is.Believe it or not, just received a call from the corporate office (Whirlpool) and they were interested...I actually got their attention. They said they would have someone contact me... she did today... so this is encouraging. I dont know what they are offering, but this poor design is a serious problem, and if you want to get in Whirlpools face better go through the BBB. I already have purchased a new part and am adding silicone to the cable to protect it from the heat...but Im really seeking full reimbursement because this is not going to end well. Good luck...

We purchased our Maytag washer about four years ago. I love the features, but occasionally we have clothes rip in the machine. We have had it serviced only once for maintenance. It is great with the large capacity. I can wash bedding including quilts and sheets in one wash. Makes laundry day a breeze for a large family!

On 11-10-10 I purchased a top of the line Maytag fridge. All had been great till we needed a part in Nov. of 2014! After nearly 3 months of searching they tell us that they no longer make parts for this unit and I am out of luck! Fridge works great but the center seal is broken (french door - Mullin) they quit making the part???? I am beyond angry! Will never buy Maytag again!!!

I feel its kind of cheap. The interior is all plastic which doesnt look shiny and clean as it use to be when it was new. Not efficient in cleaning. Can see still dirt spots in some of the washed dishes.

I have a Maytag Precision double oven 850 series. The upper oven handle does not fit snugly and has been broken 4 times. I have had to order 4 new handles because the hardware does not seem to secure the handle to the oven door. There are no problems with the lower oven door.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

A month ago I purchased a 25 cu ft side by side. First the recirculating fan quit. It was repaired. But the water and ice hose in the door froze and cracked the entire freezer door. Must be replaced, unfortunately they dont have any, so I was quoted 6 weeks for a new door, that has turned into 12 weeks and they cant guarantee me a date. I requested a replacement fridge and was told, They cant do that. I purchased the full Maytag package - stove, dishwasher, microwave. I expect better customer service than that, Take a door off the assembly line and ship it to me.

French Door Maytag MFI2569VEW10 faulty in many ways. We bought our refrigerator 7 years ago. After 2 years the freezer door handle fell off; after 4 years the right front door gasket began to tear (normal usage); after 7 years, it no longer dispenses ice or water. We now have mildew/mold growing around the edges of the door because there is no longer a good seal. Constant cleaning. Additionally, we are spending more $ to keep the refrigerator at the proper temperature because the seal is broken. To repair these items is almost $700 including shipping and tax. This does not include the cost of labor. So after 7 short years, we have a hunk of junk that does not work properly. I am shocked that Maytag sells such an inferior product and we are left holding the bag. Do not buy Maytag. Additionally, our Maytag microwave broke after 5 years. DO NOT BUY!!! Buyer beware!

I had a stroke last year in August and my children got together and bought me a washer. And after the third use this thing started messing up and I had to call in someone. Now the warranty is up and I am sitting here with a new broken down machine.

This is in reference to Maytag washer MVW7232HW0 that broke after 5 months. Maytag sent a technician out who claimed we needed to replace 3 parts. We waited almost a month for the parts to come in just to have the technician say that didnt fix the problem. We have been waiting a 1.5 months for a resolution with nothing in sight. Now we have to either way another TWO months for another part, buy a new washer and get refunded for the old one (but WE would be responsible for the almost $300 price difference it now is), or wait for a new washer to come in stock and Maytag will replace it. However according to them there are no washers in stock for the foreseeable future. This company has been a joke to deal with. I have everything recorded and will take this further.