I bought a Maytag dishwasher less than two years ago. The Maytag repairman just informed me that the control panel, the control board and the harness were burnt and needed to be replaced with parts costing over $300. I said, No, thanks. I paid him the $99 service call fee and called Maytag to see if they would help. Nope, they pretty much said, tough luck.

Has anyone talked to an attorney to see if a class action can be filed? My fridge is leaking, sheets of ice on floor of freezer, and ice maker doesn’t work. Looks like it’s the norm for these. Please post if you have spoken with an attorney. If no one has, I am going to.

Buyer Beware!! Purchased my Maytag over the range microwave in May of 2014. It has a manufacture date of Feb. 2014, and it is now Sept. 2014. It is a very nice looking unit but a bit oversized. My handyman that installed it had to raise my cabinets above my stove two inches to avoid it being too close to the range. The motor is pretty loud and It often times does not heat evenly. The light on the unit that shines down on the range is not much better than the power of a night light which is a bit disappointing considering it looks like a higher end unit, and down to the reason I am writing this review today is that for the first time I went to change the bulb. I unscrewed the the light cover which is placed awkwardly toward the very very back of the unit, only to find that when I went to twist out the burnt out bulb (that has been in there since I purchased the unit) that the bulb broke off after hearing what sounded like the break of a seal of glue, and the bottom aluminum piece of the bulb is stuck in the bulb socket. I found that the bulb is placed in an awkward place behind the light cover. Instead of the bulb facing to the left or the right or to the front of the unit it is facing toward the back which is making the bulb socket impossible to see, which means that in order to screw in the bulb you are screwing it in from an angle that you cannot see unless you climb on the range and lay on your back, or get a mirror to help see where you are screwing in the bulb. This is just a very awkward and unpractical design coming from such a well known company with such a common and ordinary product. Now I am sitting here writing this review and I am trying to figure out how I can remove that little piece of aluminum stuck in the light bulb socket and since it is not facing to the left or right and facing toward the back, it leaves me about less than 1/2 space to work with using my hand or a tool to remove that piece, or I can just leave my broken bulb piece in there and screw the cover back on until I call service for Maytag. I believe it is still under warranty but from others experience that I have read about I am not feeling confident I will receive great service or a desirable outcome. Wish me the best!! Thanks for listening!!

Maytag Centennial Impeller HE Washing Machine - The seller left this piece of junk for us. I wondered why because it appeared brand new. After the first washing I knew why. I sure regretted leaving my old set behind. This washing machine wont let you add the amount of water you need. I had to add buckets of water and hope it didnt just empty it out because the sensor controls everything. Twice it just emptied it after I closed the lid and it locked. There is an impeller instead of an agitator. It moves slightly but not enough to move the clothes. To top it off the spin cycle tears into the clothing and twists and wrings it so hard everything is wrinkled with soap residue remaining even on delicate. Each load takes over an hour and the clothes arent even clean. It went to the dump after 4 washes. I went on Craigslist and purchased a used Kenmore and am in heaven. No lock, an agitator, 3 water levels, clean clothing, you can open it and add the missing sock, no sensor controlling how you want to do laundry and no more buckets. Dont buy a Maytag. Look at all of the reviews. They arent exaggerating, they are really that bad. Thank you.

A refrigerator has to keep your food at constant temperature. The first Maytag refrigerator I purchased from Home Depot could not get cold. I mean the refrigerator never got below 65 degrees. I called Maytag and they played dumb. Just wait weeks for a repairman to check a brand new product that is not working. Home Depot replaced it in few days with another refrigerator of the same model. It runs but doesnt get really cold (it only has a fan in the freezer and the air comes down from the freezer to cool the refrigerator). I live with it because all you will get out of Maytag/Whirlpool is to turn the dial to a colder temp. A little over a year passes and the fan in the freezer just stops running. I called a local certified service person. He looks at the fan and says that its running but barely. I had to replace the motor at cost with labor of around 200 dollars. I kept the motor. Turns out the motor is made by Panasonic. The current replacement motor is made in Mexico. Now the refrigerator runs cold. Since I had two of these refrigerators that failed to get/stay cold, I think they got a bad batch of motors. Maytag response was to refuse to pay a dime, it is outside of the warranty - even though I had called about the refrigerator not getting real cold on the second refrigerator. So basically I lived with food being kept at a way too high of temp causing spoilage for a year and Maytag/Whirlpool could care less, they are only worried about their bottom line.That is not the only problem with their product. The drain pan grows a mold that looks like pudding. The only way to clean it is to pull the refrigerator out, take off the motor area cover (which is really cheap cardboard) and clean it out with a rag. There is no way to remove the pan. The compressor is mounted so low that it heats up the floor. I have concrete floors thus I have no fire risk but if you have wood floors, I would check the heat level. It is nearly impossible to clean the dust off the fins on the refrigerator coolant lines. The back of the freezer door shelves are metal and very sharp on the back. Thus if you stick your hand in to pick something up, you will get a nasty cut.I have owned only Maytag, Whirlpool and Amana products my entire life. I will never purchase their products again. They may pretend that you are buying an American product (they use the American flag) but this product is nothing but OEM garbage made by the lowest bidder. They try to sell you an extended warranty for around 300 bucks for an addition 3 years. I figured if the fridge went bad after 3 years, I would just buy a new one. I never expected a motor to fail less than a year (I would say it started going bad about 6 months into ownership as started making ice at a lower rate). Maytag refuses to stand behind their products. When I told them I had the motor that failed, they had no interest in even looking at it. Do not waste your money on their products. I also own a Maytag washer that is the worst washer I have ever owned.

I mistakenly purchased the Bravo XL top load washer. I only wish I could give it a zero rating. I have only tried to wash 3 loads of clothes. It is almost beyond belief that anyone could possibly think this could clean anything. My husband actually watched it “work”, and insists I call Maytag because they must have forgot a part! It does nothing but crumple/wad the middle items together and rub them...and only them...together. There is no movement of the outer items until it spins. Maybe Maytag should enlist people who actually do laundry to “test” the items they put their brand on. I know the government and the energy rules have added to the complex problem of buying something as simple as a washing machine...but this piece of junk is almost laughable to watch as it destroys your laundry. I’m almost embarrassed to let anyone know I bought it. Thankfully, I have 30 days in which to return it.

Brand new top of the line top loader washer. Lid locked mid cycle and couldn’t open it. Called Maytag. Sent a repairman out to fix. Three trips later, 5 parts, and over four months later, still broken. Unable to use washing machine. Been going to laundromat to do laundry. When speaking with Maytag, all you get is a sorry. Now I’m waiting on another part and then schedule another appointment to have guy come install. Maytag would rather replace every part, one at a time, than send a new washer. It is beyond ridiculous for a new washer to have to have all of its parts replaced. It’s a hunk of junk and Maytag will not stand by their product. Worthless company. Will NEVER buy another product from them. Their washer and their service is so far below standards, it’s criminal.

It seems to be a broken record with other reviews. I had a 2 year old microwave and the door doesnt recognize that its closed. Which means it wont turn on when I close the door. So you have to open and close it maybe 30-50 times and sometimes it works. I call Maytag who schedules a company but doesnt disclose anything about the warranty or service cost. I was thinking it would be a nominal fee since it falls under a 10 year warranty. The company calls and confirms the cost and I recheck with Maytag who said that the warranty only covers parts. So I buy a $300 microwave and have to pay $160 for a service visit because your company made inferior parts. Absolute sham of a company. Buyer Beware...

The microwave is 5 years 6 months since purchase model MMV4203DS. Fire started at rack clip left front rack, was cooking bacon. Called Maytag and according to them and manual on page 3 is only for 2-level cooking to avoid damage to microwave oven. DOES NOT SAY WILL CATCH FIRE OR THE RACK CAUSES SPARKS AND BACON SHOULD NOT BE COOKED IN A MAYTAG MICROWAVE. But according to Representatives of MAYTAG ** its my fault for not reading my manual. YES AND NOT HAVING THE SERIAL NUMBER THAT IS ON A PAPER TAG IN THE WHIP ZONE. The was gone from keeping it clean faded out. So I cannot be helped without the model and serial number.

Like so many other consumers, I was drawn to the Maytag name because of what I thought was the high quality of their products and their stellar reputation. So when our old wall-mount oven failed, I sought out a replacement from the Maytag line. I purchased a model MEW5530WDDB17 in 2011 and had it professionally installed. It worked well for a couple of years. Then, suddenly, three of the numbers on the digital control panel stopped working, making it impossible to set the oven to any temperature that included a 4, a 2 or a 5. When I contacted Maytag, I was informed that the unit was out of warranty, but that I could schedule a service call. I had already researched this issue online and knew that the service person would inform me that I needed a new control board and that one could be installed for around $300, and that the new board would come with a 90 day warranty. When I asked the person to whom I was speaking, she said that she had no further information for me. I know that a lot of others have had this same issue with their Maytag range/ovens, and many of them agree with me that we will never purchase another Maytag product.

The Neptune Front Load Washing Machine I purchased in December of 2007 started sounding like a jet taking off, about three months ago. The noise has become unbearable. The repair person said that the whole drum needs to be replaced and it is not worth fixing. Are you kidding me? This was an expensive washing machine and now we have to get a new one? We cannot afford to get a new washing machine. We need an explanation of why this would happen and from the other complaints I have read on the Maytag website, we are not the only ones. This is the second time something has happened to this washer, the first time, it was under warranty (only a few months into the purchase and the pump was bad and was replaced). What is the company doing to help people with this faulty machine?

After 2 years and 1 month, the machine stopped spinning the clothes on any of the cycles. After attempting to use the spin cycle manually that stopped working. I called Maytag, my washer is out of warranty. After discussing the situation with knowledgeable appliance people, they said it is probably the motherboard. I know how expensive that is to repair and pay for a repairman to diagnosis the problem. I decided to purchase a new washer. Of course, it was not a Maytag. I read online all the people with same or similar problems left out of luck. This is an outrage and Maytag should not be allowed to get away with producing, selling and not standing behind the products. These machines should have been recalled and replaced with ones that are upstanding and will last for more than 2 years.

SO SO disappointed. I thought by purchasing a Maytag washer and dryer that I was purchasing quality products. Not so. After only 3 yrs, the dryer is broken. It needs a new heating element assembly at $139 plus a visit from the technician and installation. In total, it will cost about $300 to repair. The washer is slowly going also. It takes about 2 minutes before it starts. Never used to do that. The technician told me that these do not last and that the computer is likely to go in another couple of years which will cost $400 to repair. I called Maytag to see what they could do for me. They offered the part at 1/2 price but insisted on another diagnosis even though Ive already had one. That along with their labor cost was going to cost more than anyone else. So no more Maytag products for me.

I purchased a Maytag Centennial - HE Energy Star Washer from the local Home Depot on Guam.... Probably the worst clothes washer I ever purchased. I typically buy a Whirlpool brand for many of my appliances of which I have always been satisfied with the products. I understand that Whirlpool is now the new principal owners of Maytag. I bought the Maytag for my new second home which I have moved into as my primary residence. Great ads on TV that promote the Maytag product line but the product fails miserably in performance. From the day I purchased the washer, my wife, kids, and I visibly noticed the laundry doesnt get as clean as my previous washers, it takes longer to wash a load of laundry no matter what is the preferred setting, the irritating hum is deafening in my laundry room, now the washer has malfunctioned and doesnt cycle through properly, leaving the clothes either unwashed or wet... I do not know who is your servicing agent or center on Guam and I am debating to repair it or just dispose of it. I can tell you now... MAYTAG... NEVER AGAIN. Now I know why the Maytag Repairman is so lonely.... I wouldnt bother to repair it. I hope these issues do not filter down to your Whirlpool products. That Samsung is looking pretty attractive right now. I bought one of their dishwashers that is doing a pretty good job right now.... Guess what? There was a Maytag next to it that I didnt even look at.

We purchased a Maytag refrigerator Model # M1TXEMMWS02 and Serial # E01103420 in April of 2010 from Home Depot in Aurora, Illinois. First off, we did register the fridge online via Maytag which of course, they have no record of! Now, we go on vacation and come back to all of our food ruined because the refrigerator stopped working! No refrigerator should stop working within two years! I called Maytag and they offered me a Repair Plus One package of $302.73! Are you kidding? We paid $400.00 for fridge. Then of course, only one-year warranty and have to pay at least $75 for a service call, labor plus parts! If it’s the compressor, the charge is $326.20, plus shipping and handling! What a joke! There needs to be longer warranty and should offer free service calls and much more. I am disgusted in Maytag products and in which we purchased due to a reputable name! Never again.

This product has cost us thousands of dollars in clothing!!!!!! We have a lot of pictures to prove this!!!! Greg Mackie Major Appliance does NOT back this product or US the consumer!!! We have bought THREE households of products from this distributor & they have NOT backed any of the products that they have sold us, or given us Any discount for repeat business or loyalty and have NOT Supported us in any way whatsoever!!!! We have spent thousands of dollars and have had NO compassion or support whatsoever!!!!!! We expect a full refund for this Failure of YOUR product & a NEW Machine that will CLEAN our clothing & NOT DESTROY it!!!!!! Very Disappointed in this Product!!!!!! We Will NOT purchase another product from Your Company or from this Distributor unless YOU make a conscience decision to make this situation Right!!!!! We Will Spread the Word about your Failure of a product & detour business from YOU & YOUR Distributor!!!!!! We have numerous other photos to share with consumers of how YOUR product has destroyed our clothing!!!!!

This so called high efficiency washing machine, and others like it are absolutely awful. They do not properly clean clothes. I frequently have to put loads of clothes through two or even three times in order to get things cleaned properly which our old washer did easily in one wash. That is the exact opposite of efficient. It is so bad that it actually borders on being a genuine scam. Do not buy! Huge waste of money.

My husband and I purchased the Bravos XL washer and dryer set about a year ago as our first big washer/dryer purchase for our new home. We spent about $1200 on the set from Home Depot. I very much regret this purchase as the washer never gets our clothing clean! The washer never puts enough water in the basin and the clothing comes out with strange white smudges EVERY. SINGLE. TIME.I have tried changing detergent, I have tried skipping fabric softener, Ive tried rinsing out the dispenser thinking it was residue from old soap. I dont know what it is, but what I DO know is that the clothes go in without the white smudges and come back out with them for every load. I have to run a second rinse cycle just to get it off, which means Im washing for at least an hour and a half. I DESPISE this machine and its costing me more on my water bill.Additionally, the dryer isnt much better. It constantly shuts itself off even when its not on energy saver mode, with the little red light going on for air flow. Ive checked the connection and dont see what the issue is. If I have a big load such as blankets in there, I have to dry them all individually for almost an hour just to dry my bedding! It simply wont stay on to dry a full load. I very much regret my purchase and wish Id gone with something simpler and cheaper as it would have done a much better job with my laundry. Lesson learned. Dont waste your money on Maytag.

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

I purchased Maytag refrigerator (model # MSD2572VES). The fridge side stopped working. I was told that the vent/chute between the freezer and fridge ices up and prevents the cold air from the freezer to go through the fridge. The tech said that Maytag was sending him a tube of silicone to apply all around freezer and fridge and that this will probably fix the problem. So in other words, because of a design flaw, the refrigerator cannot function without adding silicone (maybe). I believe I purchased a lemon with a design flaw and they want me to accept a permanent band-aid as the solution. Shouldnt I have right to demand another model instead of having to accept a cheap alternative (silicone)? Now, if factory installed parts break off, can you imagine silicone tubed in after the fact where there was no silicone crevasse? I cant imagine it staying on - permanently.

I would not buy a Maytag again. I am very disappointed with the noise level this dishwasher produces. I am also not happy with the inside capacity. I never have enough room for all the dishes when I have dinner parties.

I purchased a matching set Maytag washer & dryer June 2013. Sept 2013 the drum went out - 4 weeks for that repair. March 2014 the electric panel went out. Took about 10 phone calls with hold waits of 30 to 70 minutes and 4 months, to find out the replacement part is no longer available and the washer is discontinued. To get a new matching set, I had to pay for a new dryer and they will give me a free washer. I have to give both washer and dryer back - I paid for 2 dryers. 6 month later and more phone calls, no washer and no one will return my calls. The dryer I paid for is at the appliance store waiting on the new washer. We consumers have nowhere to go. I have heard so many similar situations. Where are we to go? Who are we to call?

Maytag Neptune Stacked Electric Washer & Dryer. Had to buy a motor for Washer but lasted 12 years before giving problems again; then couldnt find anyone that would service for cheaper than $100 for just coming to your house plus $75 an hour for labor. Thats HIGHER than my billable rate! Rip-off Service & parts charges. Found out it was easier & cheaper to troubleshoot ONLINE myself using FIXYA site and others. Expense for an appliance above what most run ~ 1500 for both units. Plus if it doesnt have or offer a 5-year warranty then something is wrong with the quality! Maytag Neptune Series MLE2000AYW 27 Inch Electric Laundry Center with 3.34 Cu. Ft. Washer Capacity, 4 Wash Cycles and 6.0 Cu. Ft. Dryer Capacity, 3 Dry Cycles: White. Worst part on this model was a WAX MOTOR that they used for the Washer to control the door being closed or open. Next worst DESIGN error was they didnt put a drain hole in the plastic rim seal for the Washer door, that area would build up mold & mildew if you didnt learn to keep Washer door open at all times AFTER a wash. We learned by removing the light bulb! Therefore it was easy for my crew to learn to leave the door open after washing. This model was Energy star certified and had a long life here 12 years. Unfortunately I think they build these things to only last 10 years; then you have to replace them. In years gone by... the 1970s Washing machines and dryers would last 20 years!!

I bought a Maytag dishwasher, model # MDB7749AWW1, in April 2011 and the control panel just stopped working. Of course, Im outside the one-year warranty, but judging from the other reviews on this site, that doesnt really matter. A $500 dishwasher should last more than 17 months! I agree with the other consumers. The control panel on these dishwashers should be recalled. Obviously, its defective. Instead, Im being told I can either pay $250 for the repair plus a one-year warranty or $130 plus parts to cover a onetime fix. Ridiculous.

Both the washer/dryer are of the Bravos models and both perform amazingly well. It seems everything works so well, including the vents which are thorough and vent the machine well. Our laundry is always clean and the settings on both machines work very accurately! We believe our Maytags are simply the best operating machines weve ever owned!

We bought a Maytag dishwasher 4 years ago, we had to have it serviced a few months after purchase for the soap & rinse agent dispenser not working, then a few months after warranty was up the buttons on machine wouldnt work, the control panel failed so we had to pay for a new one and install it... Well last night exactly one year from the install of the new control panel I walked into my kitchen to find it full of smoke and the dishwasher pour out smoke, when my husband came home he took the door off and sure enough the control panel was burnt and melted! Very scary. It is a very good thing I was home and this is why I never leave appliances running if I am not home.

Back a couple years ago, Dec. 29, 1983, I purchased a Maytag washer, model A209, and a Maytag Dryer, model DG110. Im still using them daily. The washer has given NO problems, other than the brake has taken to squealing. This causes nothing more than a notice that the load is done, so no repair is necessary. The dryer has proven more problematic, as I have had to replace the ignitor three times, the blower fan twice, and the motor (and belt) once. I still think I have gotten my moneys worth.

It has never failed me and I cant remember when we purchased it. When I grew up, my Mother only used Maytag Washer and Dryer. When I married (almost 50 years ago), I purchased a Maytag Washer and Dryer and have never regretted it.

We bought the Maytag Aqualift cooktop about a year ago & are continuously dissatisfied with it, for several reasons: 1) the cooktop is a huge nuisance to cook on. The burners are either raging hot (causing boil-overs), or too cool to simmer. The boil-overs then require much cleaning with an expensive cleaning agent. 2) the oven, whether you use regular or convection, underheats - so you can’t tell how long the cooking or baking process will take, & you have to monitor the cooking process. 3) the so-called self-clean is a joke; the oven will not be clean unless you crawl inside & clean it manually. Overall, I’d prefer to toss this range in the trash. I’m a good cook, but I get angry every time I use this expensive, poorly- designed product.

I purchased a Maytag dryer #MEDB400VQ for $715.48 along with a 5-year warranty for $119.99 on March 30/2012. Since then, the dryer has broken six times. Our warranty stated that after it breaks 3 times, we would get a new dryer. All claims for a new dryer have been denied. The dryer is still broken, going on 10 days, only to find out that parts needed are on back order for two more weeks. This is unacceptable! I will never ever buy a Maytag again and will tell all family and friends my story so they do not purchase a Maytag and go through the hell that Maytag has put my family of five through!

I purchased a Maytag dishwasher model #MDB6769AWB2. After 1 year and 2 months of light use (just my wife and myself), the control panel went out on it! I called Maytag and because it was over 1 year old, they would not do anything about it! When you call their number listed in the owner’s manual, they thank you for calling their Customer Experience Center. This is an experience I can do without!

The machine will not fill with enough water to wet all the clothes. I have to tape the tub to trick the machine so that the clothes will all get wet. When I had a service look at the machine he said that is how they are designed to be energy efficient. Who does not getting all the clothes wet clean them??? This is not for big loads but ALL loads - even hand wash loads. Every load takes an hour plus. Less water, more time, unclean clothes. I lose all the way around. REALLY wish I had a machine with the old features.

Maytag Free Standing 30-inch Gas Range - In 2004 we bought our model MGR5775QDS gas range with 5-burners because it offered the most BTU variety for the price: 1 burner with a high BTU (16K), 1 with low (5K), plus 2 in mid-range (9.5K) and 1 with 12K. Within half a year of using the oven, we turned on the self-cleaning function. Big mistake. One cleaning cycle later, our oven refused to ignite. The cleaning cycle burned out the ignition unit. Cant remember if its replacement then was under warranty but the repairman said this was a COMMON PROBLEM with Maytag and we best not use it EVER. In 2014 our cleaning lady mistakenly thinking she was doing us a favor, set the self-cleaning function. Once again, the ignition unit was destroyed. This time its replacement was $350 with part and labor. One and half months later, the oven is again non-functioning. This time our repair guy said the part is a very minor, inexpensive one BUT MAYTAG IS NO LONGER MAKING IT!!! The only way well get our oven back is if he can find another model and cannibalize it to fix ours. Are we disgruntled? Yes. Would we like to see a class action suit against Maytag for knowingly manufacturing a gas range with a malfunctioning self-cleaning unit that destroys oven parts? Yes. Will we ever again buy Maytag? Not on your life. A once stellar manufacturer gone down the tubes with a growing reputation for making junk. American-made appliances mean zip these days. Thank you for nothing, Maytag.

I bought a Maytag washer and dryer about 2 years ago. I’m on my second washing machine (one was replaced from Lowe’s not Maytag). The second washer has now gone out! First it was the lid lock and now who knows! The repairman can’t even fix it. Biggest piece of crap, stay clear!! My first set lasted 25 years. Poor quality workmanship and customer service!!

Same problem as all the others, the dishwasher stopped working. The dishwasher is less than three years old; for a two-adult household. The control panel just stopped getting power. After multiple calls to Whirlpool/Maytag, all they will do for me is document my complaint. Im now out $167 to get this thing running with no guarantee that it wont happen again, as well as the fact that this should not have happened in the first place. I didnt misuse my dishwasher. It just stopped! I think there needs to be a class action lawsuit since the manufacturer will not stand behind this obvious defect.

I purchased my Maytag Centennial Commercial Technology MVWC200XW in May 2012. This is the second time in almost 3 years that it breaks down. The basket decided to drop today and by the time I realized that it did, my whole bathroom had flooded, the water spread down the hall into my spare bedroom and soaked through the floor, also flooding my basement. I called customer service. They are sending a repair man next week, but as for all my ceramic tiles that are now cracked in my bathroom and my hardwood in the hall and bedroom that is full of water and are lifting off the ground. Its my responsibility to call my insurances to fix it. Yet it was their washing machine that caused the damage in the first place. When I purchased the washer I didnt expect to have to repair it every year. Not impressed! I do not recommend this washer.

We purchased a bottom freezer refrigerator from the Home Depot in 2013 and I am sorry to say this refrigerator does not deserve any stars. Immediately after the warranty was up our refrigerator started leaking all over the floor. The drain clogged and freezes up on the bottom under the freezer. When it becomes full, it leaks all over my hardwood floor. I have now become a slave to this refrigerator. Each week I have to open the freezer and get down on my hands and knees to break up the ice, scoop it out, toss it in the sink. I have spread the word and I hope anyone who reads this does as well. Never buy a Maytag product because not only do they make defective products, they wont own up to it and recall it.

My old washing machine was about 25 years old but still doing a fantastic job getting the laundry done. When the dryer died we decided to replace both machines so theyd match. I had been setting money aside for years in preparation for this purchase. Ive only had them for two weeks and I stay awake at night wondering what GENIUS decided you can get clothes cleaner in a tablespoon of water than you can in an adequate amount of water?! My old washer could wash a load of laundry in about 20 minutes. Again, what GENIUS decided taking over an hour to wash a load of laundry in a tablespoon of water was a better way?! What working woman would choose to double the time needed to do laundry and then not feel confident that the clothes are clean?!!! I am so mad and frustrated and disappointed and I dont know what to do. I wish I could yell at somebody!!!

I purchased my Maytag double oven (MEW6627DDB) in November 2008. In January 2013, with a setting on 375, it heated to 440 in 15 minutes. The repairman said $650 because it needs a new control panel and 2 new sensors, one for each oven. I contacted Maytag as I felt this oven should not have gone out in 4 years. I spoke with Ebony and then a supervisor, Vana. Basically, I was told that since I didnt purchase an extended warranty, there was nothing they could do. While I have a freezer 40 years old and still going strong, I realize that appliances manufactured many years ago were much more reliable. I feel that Maytag should stand behind their products and should have offered to send me replacement parts. I know I would have had to pay labor for installation. Their answer was I should have purchased the extended warranty. However, one should not have to purchase extended warranties for products. I had every confidence in Maytag. Why else would I have purchased my first Maytag product? I should have stuck with Whirlpool, which I was recently told, now owns Maytag. Maytag customer service personnel were extremely unhelpful. I wonder how many Maytag employees purchase extended warranties for their appliances or if theyre smart enough not to buy Maytag.

I purchased a Maytag refrigerator (MBF2258XEB), stove (MER8674AB) and dishwasher (MDB7749SBB) on May 26, 2013. So far all three have been worked on. First, the dishwasher would not fill up with water after the trial run. Called the repairman out. A tag was placed in a position that was preventing the dishwasher from loading up with water. Granted, we should have taken the tag off, however, it stated not to. Lucky for me, I am still under warranty. Second, the refrigerator, which is a freezer at the bottom, started to leak. I thought that maybe we were dropping ice. However, I finally called and had the repairman back out. He knew exactly what the problem was because Maytag knew about it. There was a faulty plug. So in a matter of mins the problem was fixed. Lucky me still under warranty. Those two things happen within six months of purchasing these items. Now, the oven does not work. It heats up to the desire temperature but then cuts off. Called the repairman and he thought it might be the lower baking element. Unlucky for me, warranty has expired. So, $90.00 for service call. Received a called from the repairman, $120.00 for labor and $70.00 for the baking element. I purchased the baking element myself, $58.08 and installed it. Still does the same thing. Now I have another appointment for him to come back out and see what is wrong. Another $90.00! So far I have spent $238.08 on a $699.99 stove. I will never buy Maytag again. Depending on the amount to repair will depend on whether or not I go back to Sears and buy Kenmore. I had Kenmore for 10 years with no problems. I should have gone back to Sears for my upgrade. I did contact Maytag via email. I am still waiting for a reply. Live and learn!

I have a Maytag Centennial washing machine which is about 3 years old. In the past 6 months I have to replace the actuator twice. I have had Maytag washers for about 40 years. I will never purchase another one unless it is the old style. That would mean that it would be a used one. This machine is a bad purchase. Maytag use to stand for quality, but not anymore.

If you are considering this product...RUN AS FAST AS YOU CAN!! This is the biggest piece of junk Ive ever owned!! I would be more than happy to take back my 20+ year old washer over this JUNK!! It is 2-2 1/2 years old tops. I cannot count how many times my husband has already had to repair this garbage!!! I will NEVER purchase another Maytag appliance! My stainless steel dishwasher isnt any better!!

I have a Maytag refrigerator - the kind with the French doors with the freezer in the bottom and then the middle drawer is now leaking water all over my hardwood floors. This is ridiculous. Maytag better get off their butt. They need to send people out or send letters to people that have these freezers to fix them. When you pay a lot for something they should get a good product. If there a recall they should of send out letters or something.

Purchased my Bravos June 2012. This is a horrible washer. It does not clean. It leaves a detergent scum line on clothing. My work clothes are visibly soiled and sometimes come out in a tangled mess. Maytag ignored a first complaint from my wife. I complained again today. Regardless what Maytag does, I will purchase another brand after research. We bought on Maytag’s reputation.

Well, I thought I was buying quality products dishwasher and refrigerator and both are very disappointing. Of course the Maytag dishwasher (MBD7749AWB2) really upsets me since I just bought it in Aug of 2011. Now it will not finish a load of dishes and I did what the lady at Maytag told me. She said it was the control board. But it is not the control board. It is still working the same as it was. Now what should I do? When they said I had a 10year warranty I didnt think a known product like Maytag would let me down. MAYTAG, YOU SHOULD BE ASHAMED TO ADVERTISE YOUR PRODUCTS TO LASTS! THEY SUCK!

We just received a Maytag delivered by Home Depot. THe box the diswasher came in was soaking wet. I called within 30 mins of delivery to report this. Home Depot called and Maytag refuses to replace the diswasher stating that it comes wrapped. No it does not, the diswasher and insulation were soaking wet. Maytags response is just let it air out. So Im supposed to air out a 470.00 brand new dishwasher. Home Depot is also getting its one star review for refusing to replace it and letting the third party contractor get away with delivering a damaged unit.

Dishwasher cleans well, but the control console has failed again & only responds to two functions. After replacing the console a couple of years ago with a new unit I thought it was done (it didnt get much use). Is there any recourse for this complaint? All I want is a new console panel. Maytags brand is apparently only good on the commercials. Very disappointing. Also, the top rack is very awkward & is only good for short glasses etc.

I had a warranty that I bought over a year ago. The dishwasher since then has been a monster beyond control. I called Maytag and the woman asked how long it has been acting up. I said about a year, but I was not sure. They refused to honor my warranty because they said it would only go into effect 60 days after I purchased it. They are translating about a year as an absolute and refused to honor the warranty. I would never ever buy a Maytag product again. Never. I will contact every person I know not to buy such a faulty product.

I purchased a Maytag Bravo washer and dryer in 2008. I had a repair person out today on both units. I was told that it will cost as much to fix the washer as it would be to purchase a new one. As far as the dryer was concerned, I was told to live with the timer issue rather than replace the expensive mother board. I was also told that the drum bearing issue with the washer is fairly common with the Maytag machines. It looks like the Maytag repairman isnt so lonely anymore! I paid a lot of money for these machines and they amount to a hill of garbage after three years. I may be buying a new washer, but you can bet your boots it wont be Maytag/Whirlpool!

The only complaint is the lights on the bottom quit working about a month after we purchased. It was nice to light up the stovetop when cooking. Now it’s slightly dark. I have gotten used to this. We spent about $8000 on all the matching Maytag appliances we purchased. I would love to replace all but not in the budget. I am a dissatisfied Maytag customer.

I bought this machine in 2013 and within a year it had stopped going through any cycle. It turns off and I either have to restart a cycle or set the machine to rinse/spin. My clothes do not seem clean so I have begun handwashing them before putting them in the machine. I retrieve clothes and find some clothes dry. My towels have worn spots and threads pulled out. I cannot wait till I get a new washer because I am going to put this Maytag Bravos in the backyard and take a baseball bat to this hunk of junk.

Bought a Maytag 4000 series washer and dryer combo for about 2100 dollars in October 2011. Had a professional look at it today since the clothes stayed wet after the spin cycle. Told us it would cost 1000 dollars to repair the washing machine. So a total write-off in barely four years. I am very disappointed.

We have owned the dryer (Maytag Bravos) since Dec. 2010 and are now on our 4th service call. Upon the second delivery of the part that was ordered last week - we will be on the 5th service call. I finally asked Maytag if I could get a trade in since this dryer is obviously crap. They said they could only handle the problem at hand, which is the same problem over and over and over. The flywheel was left off all together. The pulley belt for the dryer pops off about every 4 to 6 months. Ridiculous. Its a crap dryer, dont buy one!

In 2006, my wife and I purchased a new Maytag refrigerator, the model type with the freezer in a drawer near the floor and the drawer is under the main door of the fridge. The thing has a sealed system and has a freon leak which makes it nearly impossible and not financially prudent to try to fix. Two repairmen were out and I spent $200 for them to tell me the same bad news. Its unbelievable that this junk wouldnt even last ten years. What is this, Russia? Ive heard some of their awful appliance experience stories and now this can join them. The reliable Maytag repairman who never has anything to - you know the one. He is probably dead. Hes not really the one to blame here though, it is the reliability of Maytag that is dead and will remain so for as long as this company is alive. Dont ever trust or buy Maytag if you care about making your investment in new appliances last! Dont do it, people!

Our Maytag oven (not sure model) in the first year started doing crazy things with the oven computer. The oven would shut off and come back on and the display would be garbled. Also when my girlfriend tried to pull the turkey out, the rack fell off the left side and dumped all the juices into the oven. She almost got burned and there was a lot of smoke. The freakin rack should never fall off! Also our dishwasher is on its second control board. I lived by Mr. Maytag and his airplanes/helicopters at Crest airpark in Covington, WA. I wish I still did. Id like to ask him what he thinks of his crappy products. You get nothing for your money anymore. Im not sure but Ill bet both of my problems with these products have something to do with saving a buck by making this crap in Mexico or some other *** hole. Im just glad Maytag doesnt make airplanes or medical equipment.

The Maytag Refrigerator Model #MFF2558VEW2 I purchased from Sears is a lemon. Ive had problems with the freezer getting a sheet of ice, under the storage basket. The ice starts melting, and pours out on the floor. I have to remove everything from the freezer basket, remove the sheet of ice, and mop the floor. Ive had problems with a great deal of noise coming from the unit as well. The unit has now stopped working completely. I called Maytag at 1-800-253-1301, and spoke with customer service. I was informed of a faulty part, in the freezer. I received the part in the mail, and a phone number of their contracted repair company. The repair man charged me $166.00 to install the part, and informed me the digital control board needed to be replaced as well, for an additional $170.00. I called Maytag again...they said nothing could be done about it. Ive had the refrigerator for 3 1/2 years, and had all these problems for over a year. Im not going to invest over $300.00 to repair a faulty product. Maytag should stand behind their products, and at least furnish the parts, or replace the unit, with something that actually works.

Maytag Bravos XL MVWB980BGO. To start, I live on an acreage so some problems may be related to being on well water. The most annoying part is the washer doesn’t have a drain & spin without rinse. So, when my well pump started acting up, I had no way to just drain & spin off the load, so I had to try to lift thoroughly soaked clothes and try to dry them...which took about four hours. Another aspect that is a pain is uneven loads. It keeps trying to fill, instead of just stopping & letting me adjust the load myself. Then the damn thing won’t reset. I often have to resort to unplugging the machine and starting over. High efficiency is a joke. I’ve had the machine about five years now and it goes low flow error, even though the flow is fine. I’ve tried running cleaners through the water line and it’s still doing the same thing. The only thing left to try is take the machine out and try and manually go through the lines. For the amount of money we spent on this machine, I am thoroughly disgusted with how it runs. It is the first & last Maytag washer that I will ever buy. Next time, I’m buying as cheap & basic a machine as I can buy. On the upside, the dryer works perfectly.

We purchased the Bravos X washing machine on Feb. 9, 2012. I had a Maytag for 30 years before this one and did not have any problems. My model # is MVWX700X. I have given it sufficient time to get used to it. I have tried all cycles for my whites and am not satisfied. I use Clorox in the receptacle and I have only used Tide HE. I spot treat all of our underwear, which is changed every day, and it always comes out unacceptable. I am so disappointed since I was so fond of my old one and only thought I wanted another Maytag. At this point, I would never recommend this machine.

We purchased a Maytag electric convection oven with a warming drawer 3 months ago. We have been happy with the cooking features, but not the Aqualift self-cleaning. It does not work and Maytag does not acknowledge this. Instead they have offered cleaning products to us which their own instructions tell you not to use! Does this sound like a self-cleaning oven? They have offered to send out a service person to check the temperature. However, from reading multiple reviews by others, there will likely be no satisfaction from this company.

I just bought my Maytag Range model #MGR8700DS2 in August 2016. Bought Maytag because I always thought it was one of the best with the best warranty around. Now I am not so sure. After using it the first time, found that when you are baking anything in the oven the burner control knobs get very hot. That is because they designed the knob area to be right above where the heat vents out from the oven door. The knobs get so hot that you almost burn yourself if you touch them. This is a bad design in my opinion especially if you have any kids around. Even the sides of the oven get way too hot. This is also bad because of the tight spacing to your cabinets. I contacted Maytag about this and got a OH WELL kind of reply to my problem. You bought it and you are stuck with it. I would not recommend buying this model to anyone.

My dishwasher just stopped working 1 year after purchase. Apparently a control panel issue. I have sold Maytag appliances for over 10 years and this is the thanks I get Maytag... Unreal. I wont buy a Maytag, Amana, Whirlpool, Jenn-Air, KitchenAid, etc.

The way the side by side fridge/freezer is built contributed to several injuries. I am 60 tall and of normal size, and accessing anything in the side doors lower down always results in smashed head, near bleeding injuries. I am so sick and tired of it. No other fridge has done this to me. Add that to the shelves being near razor sharp. One of these days this fridge is going to land me in the hospital with a lawsuit. Most people are not 3 feet tall or 8 feet tall, thats the only way to use this fridge safely!

I purchased a Maytag Legacy Series Quiet Series 300 in early July 2010. It had a recall for a heater part that could potentially burn down my house, so we couldnt use it while we waited for that part to be replaced. They offered me a small sum of money towards the purchase of a much more expensive dishwasher which I declined since Id only had the dishwasher a few months at the most. It is now the end of August 2011, a month past their factory warranty. The dishwasher did not get my dishes clean, made awful grinding noises and three days ago, it refused to drain and then spewed 50 or more gallons of water all over my kitchen which then leaked into the basement. The repairman charged $85 to tell me that the computer in the control panel had burned out and was not fixable. I think I paid somewhere in the region of $500 for this machine. My last dishwasher lasted about ten years. This is completely unacceptable. In searching the internet, I found hundreds, if not thousands of identical complaints. Clearly, this machine is a lemon and Maytag should be forced to replace it or better yet, refund the money spent to purchase the machine. Plus, pay for my valuable time spent mopping up water, washing dishes by hand, searching the internet for probable cause and potential solutions, waiting for Maytag/Home Depot to respond to my inquiries and a large sum for general annoyance. Maytag had a reputation of reliability (emphasis on had). Theyve got some slick ads but they do not stand behind their products at all. I will never by another Maytag product and I urge you to do the same.

Maytag Neptune was purchased over 15 years ago to replace GE, which we purchased when children were little. I wanted a step up in quality. I remember paying around $499 for this unit. This is an analog unit. The intellidry feature has been a real asset, protecting our clothes from over drying. We have had this machine for nearly 20 years. It has been real reliable, sometimes drying 20 loads a week. Large capacity, but has to fit down a narrow and twisting stairway. Must be energy efficient, have good reviews and decent price. We always look for sales or buying incentives. Brand is secondary to quality. Knowledge of an appliances historical reputation is important. I would look at reviews, especially concerning cost of repair. I would attempt to get a hands-on view, before purchase from a reputable supplier at the best price. My dryer has only required one major repair in the time Ive had it. A few years ago we replaced the motor and blower, and I have personally replaced the drum support rollers twice. I hesitate to replace this machine, because the analog controls have proved very reliable.

Maytag Centennial 3.4 top-loader was purchased at Home Depot. It has never worked yet. On 4/28/12, the third weekend, I sat home for the servicemen to fix this junk machine. The first two times, the machine didn’t work ten minutes after they left and today they went to the wrong address. I have much more important things to do than to sit around and wait for someone to figure out what is wrong with this machine. It would have been cheaper for me to junk this brand new machine and buy a washer from a company that makes washers that work!

Maytag washer was bought May 2010 with an extended warranty, which expired May 2014. This machine was used by two people with average wash loads. Five months later the machine computer programming didnt work and the machine sounded like a jet taking off. Whirlpool said a one-year warranty would cost $329! This would have been less expensive than a new machine, but I felt I couldnt trust having it repaired. A repairman very familiar with Maytag products said he had three service calls the same day with similar complaints for the Bravos 300 series. He told me the bearings were bad and the cost to fix was not worth the money and this machine should have been recalled. I bought another brand and will not buy Maytag again. When my new machine was delivered, there was grease on the floor from the Maytag.

I purchased my Maytag MDB7749AWM2 dishwasher approximately 3 years ago. Since it was stainless inside and out I felt that I was making a long-lasting purchase. The handle on this particular model doesnt have a latch release button. You are actually just pulling the door open. That would be fine if they had used something besides plastic on the control panel cover where the handle is built into. The control panel is only held together with plastic pieces that the screws go into. After only a couple of years of pulling on this the plastic parts holding the screws have all broken causing my control panel to just flash. My husband is a maintenance engineer and upon taking the screws out couldnt believe with such a high quality machine that they had used plastic in the main place where they needed strength. The wiring was cut so short to the control panel that one of the plugs had come undone when the cover began separating. I only need the plastic cover because my control panel is working fine but of course you have to buy the entire control unit which is $150.I purchased Maytag because I thought they represented a reputable American company but I was very wrong. When I contacted Maytag about the problem they were very unconcerned and just gave me a link where I could purchase the part. When I told them it would be my last Maytag product they didnt even have a comment. Giving Made in America a bad name.

I am having the same problem with the sheet of ice forming on the bottom of the freezer and leaking water out every week or so. It is getting very frustrating. After reading all these reviews I am realizing it is a manufacturing flaw and think there should be a recall. We have model MF12269VEQ3.

First let me say I have used Maytag products for 46 years. A little over a year ago bought a new Maytag Centennial Washer (Model MVWC555DW) for a cousin which was responsible to looking after as he had been brain damaged since birth. Needless to say when I started having trouble with clothes not washing and having to bring to my home and wash was not satisfactory. This machine never worked right but until after the 1 year warranty could get by. Needless to say I will never buy another Maytag appliance but now have a Maytag washer/dryer, stove and dishwasher in my home. Maytag is Not the quality that is use to be. WOULD NOT RECOMMEND THIS MACHINE AND ALSO UNDERSTAND FROM LOWES THEY HAVE HAD A LOT OF TROUBLE WITH THIS MODEL.

I bought a high capacity Maytag Bravos washing machine, thinking it would be better than the ones that shred your clothes around the center post. Wrong. You still have to wrap your clothes around the edges as if there were a post, and even then the machine will become unbalanced (after much thumping and crashing), causing it to stop, which forces you to redistribute the weight, sometimes several times in one load of wash! I called the company and got nowhere -- I wont say nowhere fast because it took forever to get nowhere. I do not recommend this machine.

We purchased our Maytag Bravos washer/dryer in January of 2012. In October of 2013, I noticed that the lid would not close properly. In examining the lid, we discovered that the screws were in tact but the information panel on the inside of the lid had come unglued causing the lid to be obstructed from closing properly. After calling Maytag we were told that they make a quality product and, in what I consider to be a condescending reply, could not help us. Replacement of the lid with the service call would cost almost the cost of this expensive washer. So disappointed in what we thought was a wise purchase!

2011 model MVWC2oox W1- spin dry failure - We purchased above top loader in 2011 and have had no issues until now. Currently constant failures on spinning and drying. Spin cycle stops without getting up to speed and appears to be an unbalanced load sensor problem. Also draining is not completed (possible pump going bad). Area tech came out within a week as promise and ran the diagnostics and found no faults. Problem has continued. We do a load a week. Looking for better answers or a new washer.

I purchased the matching Bravos Washer and Dryer in April 2010 at Lowes. I also purchased the extended warranty to have coverage for 4 years after purchase date. I noticed the dryer sensor is not very accurate. The purpose of the sensor is to detect when clothes are dry and then end the drying cycle automatically. However, it fails in both ways. When the dryer stops on its own, the clothes are still damp. I have the setting on NORMAL>LOW HEAT>NORMAL DRYNESS (the reason for the low heat is not to fade/shrink clothes) and even though the heat is on low, it should still keep running until the clothes are dry. So when I open the door and feel the clothes, they are still damp; I turn it back on to run again. If I dont check on it every 10 minutes, the dryer just keeps running and the clothes are bone dry. The sensor should detect this. Once, I decided to test it to see how long it would run with dry clothes and it ran for an HOUR before it shut off. Talk about a waste of electricity.The washer also has issues. First is the SHEETS setting. This setting is supposed to prevent sheets from tangling/balling up. Every time I use the sheets setting, my washer stops with the UL error - uneven load. Meaning, I have to babysit the washer because otherwise, it will stop and wait until I pull out the sheets and loosen them up. I am only washing 1 fitted full size sheet, 2 flat full size sheets, and 4 pillow cases. The reason I bought this machine was because it is supposed to handle king size bedding. Apparently, this washer cannot even handle full size bedding and I refuse to wash each item individually - the machine is supposed to save energy, not require extra loads. The second issue I am having, which resulted in me calling to utilize my extended warranty, is tiny rust dots on my clothes! About 3 months ago, I noticed one of my t-shirts had 4 tan spots smaller than the size of a dime. I assumed I spilled something on myself. About a month later, I noticed it was on another top. Then I assumed it was something on the back of my chair at work causing the spots. It seems to happen every couple of weeks because another article of clothing had these mysterious dots on them. Once, it appeared on my towels and sheets. I realized it was not me spilling anything on myself, nor was it from anything on my chairs. Now, I wasnt sure whether it was the washer or dryer, but I noticed when I pulled out a white sweater from the washer, there were 3 dots on it in the front, and I definitely would have noticed these before, which is how I came to the conclusion it’s from the washer. I cannot see any rust inside of the washer basket so I dont know where its coming from, but I am certain it is not from other articles of clothing (such as zippers or snaps); and the reason I know this is because I do not wash towels with clothes and also, I am 8 months pregnant and have been wearing maternity clothes for the past 5 months and they do NOT contain any zippers or snaps. I took pictures of the rust stains on various items and combined to 1 image. Now, I called my extended warranty to have a service technician come assess these three problems. Well see what happens.

I purchased a Maytag Bravos XL Commercial Washer on Jan.31, 2020. I have had problems with the control board twice in less than two years. To replace the control board it cost $560 plus dollars. I may as well get another washer. So, I have to buy two washers in less than two years, but the next one will not be a Maytag. I will not recommend their products.

Maytag Bravo Washer - I recently purchase a fairly expensive washer built by Maytag. In my opinion it is the worst washing machine I have ever owned. Again in my opinion their advertising about being such a reliable company should be considered false advertising, and near criminal. If you had a lower rating I would use it. Absolutely you should never use the word Bravo in a description of this washer. I will never purchase a Maytag appliance again. Check the internet for reviews before you purchase. I had just came out of surgery and in a wheelchair and trying to move back home and didnt do my homework.

Bought a dishwasher about 2 years ago, through Home Depot. After it was installed, contacted Maytag to let them know that it didnt seem to be working correctly. They sent out a repairman, who looked at the machine, and then told us that with the new eco friendly settings, it would be best to let the dishes dry overnight. It seems that the company and its employees dont know [or care] about the product. Contacted their service/helpline to let them know that the screws on the insides of the latch [on the cover] are NOT screwing into anything, they come loose. Person couldnt find same in his system, finally sent screw, but they were the wrong size and didnt work. Just opened the dishwasher this AM, after washing the dishes last night. 12 hours later and they still are not dry. This isnt eco, this is something that is wrong that Maytag doesnt want to address. Buy something else!!!

After one year, this famous Neptune washing machine began to sound so noisy during the spin cycle that neighbors must have thought a 747 was taking off from our house. After researching the web, I found that the main bearing always fails in this machine and there is a new one-man repair industry started up across the US to just replace these bearings. In fact, someone invented a bearing puller just for this problem. I am deeply disappointed that a once fine company would knowingly put out such trash. I am replacing ours with another brand, even though we have used Maytag for 30 years. Customers always determine who wins and who loses in the long run. Bye, Maytag!

A little over two years and my Maytag dishwasher needs 300 to $450 in repair for circuit board or boards. The repairman said that they got cheap and left out a seal which allows moisture to get into the electronics, duh. They have a known problem but will not stand behind their screw-ups. Never again will I purchase Maytag, Whirlpool or any other product made by the bumbs.

Our product was purchased with our Condo. We have had it for 6 months & the first time I called someone was for the oven door being so terribly hot. I was told that was normal. Then I tried the cleaning of it & you would never know anything had been done. It would take a heck of a lot of elbow grease to get the marks off & I dont have the strength or time to be doing that. I had someone come again & he said to do it again, which I did & it still was not clean. I have done it a 3rd time now & still no better. I think this product is a total piece of junk & would not recommend it to anyone. I am a very unhappy customer & will never purchase another MAYTAG product.

Well, my washer is 2 years old, yes thats right - 2 years old. And it only goes to the wash cycle, washes once and stops, wont complete a full cycle. Yes, the brand with the commercial with the repairman just sitting around because their products are so great you never have to work on them. Yeah right. And Ive seen videos on YouTube on the problem with the Maytags. So Maytag may want to look into it!

My refrigerator is a lemon! We bought a Maytag bottom freezer French door refrigerator model #MFD2561HEW in May of 2007. Less than a year later, it stopped working and ruined all the food inside. I cant remember the problem that time, but it was fixed by Maytag and we were reimbursed for a portion of the food we lost. Two years later, the temperature got warm in the refrigerator and freezer sections, and we were gone for a couple of days, so when we got home, all of our food was spoiled. This time we had an extended warranty in effect and they replaced a circuit board, but we were out the food. A few months later, the same thing happened. This time we were home and saved most of the food. The compressor was replaced, again under warranty, but it took 2 weeks to get the part. Now, less than a year later, the freezer and refrigerator compartments are getting too warm and frost is forming in the back of the freezer. When it finally does get cool, it freezes the food in the refrigerator section. It also makes loud bumping sounds. I paid $80 to a repairman today to tell me that theres nothing wrong with it, thats just the way it runs! He suggested I put a gallon of milk jugs filled with water in the freezer to hold the temperature when it starts to rise! This piece of junk is just 5 years old! When I complained, I was told to call Maytag and discuss it with them. This refrigerator was not cheap and I see that many others have had similar problems. How do they get away with selling an inferior product?

I bought a Maytag Dryer from Lowes in December of 2013. I paid 600.00 for this dryer which I thought was going to last for quite awhile. It stopped working in January of 2016. (2 years old). I had a repairman come out and he said the motor had burned out and he wanted 300.00 to fix it. I called Lowes and asked if I should expect the motor to burn out in 2 years; they said of course not - call Maytag. That proved to be a complete waste of time. They would do nothing. They simply said that there was not a recall on that machine and they were not technicians. However they would be glad to send someone for 125.00 dollars to look at it, then the parts and labor would be more. I have never had a dryer burn out in 2 years - not even when I was raising children and using a dryer daily. This Maytag clothes dryer isnt even used every week and when it is used, there are a few small loads. I am appalled and disappointed in Maytag and the poor quality of this appliance as well as their horrible customer service.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

Just replaced a washer that lasted over 7 years thru 3 renters with the Bravos top loading washer. There is nothing efficient about a cycle to take 73 mins to wash 20 articles of clothing (t-shirts, socks and underwear). The machine dont wash the top of the load. Also the deep clean feature isnt deep cleaning. I recorded a video of 20 mins of the machine not washing properly before going into rinse cycle. If this item dont produce refunds of the amount of water wasted RE-WASHING and electricity because it doesnt clean on first wash, then its time for Maytag to pay my utilities. For the money spent on the machine, going to the laundromat every other week with 1 roll of quarters each trip comes to be I can wash for 4 years and will outlast the longevity of the machine before it breaks! Also bulky mode is how you get more water in the machine but will take 63 mins to wash.

I have a Maytag Neptune washing machine which had a mold problem on the rubber grommet. I have been trying to call Maytag to no avail. I researched and saw there was a class action suit for this very problem and I was never informed. The washer may pose a health hazard and I would like Maytag to do something about it.

Theres always a problem with this thing. It doesnt clean the clothes, its always off balance, and now it leaks from the bottom side of the machine in the clean washer cycle. Its only 2 1/2 years old. Should of listened to the guy who fixed my old machine. Dont get a Maytag!

In late March or early April 2010, I purchased a Maytag Microwave from Sears in Ocean, New Jersey. The microwave was installed by Sears technicians on April 9, 2010. The total price for the microwave and installation was $356.53. I specifically purchased the Maytag brand because of Maytags longstanding reputation for quality products with long lifespans.On October 5, 2014, the microwave became inoperative and displayed a code of SE. On or about October 9, 2014, I contacted Maytag Customer Experience Center, via email, and advised them of this problem. I also wrote to Maytag explaining the situation. On October 15, 2014, I was advised via email that, as my warranty had expired, any repairs were my responsibility. I requested that my email be forwarded to Maytags CEO for consideration and review and was advised on October 20, 2014 that a Maytag supervisor would call me within two to three business days (of October 20th). After a follow up letter to the CEO, I was again advised on October 28, 2014, that the microwave was out of warranty and any repairs were my responsibility.I should add that I contacted Maytag Repair Service and was advised that the price of the repair far exceeded the price of the microwave. I feel that four years is not the expected lifespan of a microwave, especially a Maytag, and can only conclude that the Maytag microwave which I purchased was defective. I have purchased less expensive microwaves that have lasted for at least ten years. I got absolutely nowhere with Maytag personnel, found them to be curt and dismissive and would NOT purchase another Maytag product nor would I recommend them. Buyer beware - Maytag is not what it used to be! Very disappointing.

This machine is awful and a waste of money. Don’t trust the reviews with “workarounds.” That’s crazy! Doing laundry is difficult enough in my house so I need to add extra work? And they don’t work anyway. Water is barely 1-2 inches deep. But the real issue is the clothes don’t come out clean. Of course, they smell clean because all the soap hasn’t rinsed out but they are not. I spilled coffee on a white tee. Dabbed it up with a wet napkin. Threw it in the laundry. Did whites and added extra bleach and extra water because I know how much this machine sucks. Not only are my clothes yellow but the coffee stain is still there. I can’t imagine how it will wash tough stains like blood and wine and grease. I cannot even believe they are allowed to rip people off with this product.

Wish it was a French door style instead of freezer on top. Not good if you are tall. Other than that we are pleased with it but will look to trade for a French door style.

I bought a Maytag Bravos Quiet Series 300 washer just over two years ago from Home Depot. The control board and sensor went out last week. The service technician seemed rather surprised that a newer machine would have that kind of non-wear-and-tear problem and suggested that I contact Maytag/Whirlpool to see if they could help offset the parts costs, as the repair was going to cost over $600! The customer service agent I spoke with said that there was nothing they could do because the item did not have an extended warranty. I explained to her that we purchased this unit, even though it was out of our price range, because we were told that it would last a lifetime. I would have been happy if it would have just lasted 5 years! She was very detached and it was clear that Maytag/Whirlpool was not going to stand behind their product. I will now take the repair money and go buy a new washer. You can be sure that it absolutely will not have the Maytag/Whirlpool brand!

Maytag junk MFW2055FRZ00. We had to replace our reliable 15 year old Frigidaire side by side fridge when it failed due to a compressor failure. We should have pressed the service company to replace it or found someone who would. We were limited in replacement units because of built in cabinets, thus a smaller French door (so we have to open two doors rather than one) Maytag. Perhaps our 30 year old Maytag washer and dryer made us believe Maytag still offers high quality products. We were wrong. Everything about the unit is poorly designed, cheap and flimsy. The freezer drawer pulls out unevenly and the ice maker is primitive. Above all no matter what appliance you choose be sure there exist factory authorized servicers in your area otherwise warranty issues are a problem.

My original GE dishwasher that came with our house finally crapped out after about 8 years of use in 2007. Bought a Maytag from Home Depot for around $400. Dont remember the model number. It worked okay but then in the middle of 2010 we got a letter in the mail saying our machine was being recalled because the heating element might catch fire (!!!). The recall gave us the option of getting it fixed or getting a $150 rebate. We chose the rebate option so we trashed this dishwasher and went back to Home Depot to buy another one.We found a very nice Maytag with the stainless steel tub and the racks with the lifetime warranty against corrosion (which was good because our previous Maytag had started to leave rust on our dishes because the plastic on the tips of the rack tines was starting to come off), model #MDBA979AWB1, serial #FY2501885. The one we found was a no-box display model but it had all the accessories with it and still had the factory warranty. We got it for just over $300 and with our rebate applied we were out the door for under $200 including tax. I installed it myself and didnt have any issues for quite some time. My wife and I were both very happy with how clean the dishes got!Now, last night the dishwasher wouldnt start. I checked it out this morning, made sure it had power and was able to get some lights on the control panel to light up but still couldnt get it to start. Looks like Ive been victimized by the control board as most of these complaints have said. I guess I should consider us lucky since ours seems to have lasted longer than the average 18 months to 2 years. Will be contacting Maytag and Home Depot to see what they can do but after reading all these negative reviews Im not hopeful.

What junk. Bought this gx2shbxvy05 french door fridge. In less than 16 months the freezer is fine the fridge section gets up to 80f. Throw all the food away. Found the freezer coil covered in ice. Took the back panel off and noticed ice around the copper tubes by the compressor going up into the body. Not good. Put a small brick heater in and slowly melted the ice into the drip tray. Warning, it filled up 4 cups of water and of course spilled and killed the wood floor. After the clean up. Plugged the unit in and it seemed to work for about 3 months. Now its dead again. Looked into parts around 300 to 400 bucks plus labor to replace the system needed parts. P.S. the fridge, this junk replaced is downstairs working after 25 years not one issue other than the color. NEVER BUY A MAYTAG product please. TRAIL APPLIANCE should never have sold this product and should have stepped up to help out. Wont buy from them again.

I purchased a Maytag dishwasher (Model MDB7809AWWI) in Sept. of 2009. In 2010 and 2011, it had dead control panels. The first time, it was under warranty. The second time, it was not, and I purchased a costly service plan to have it repaired. Now, 2012, its dead a third time. Maytag tried to tell me that I could purchase another plan for $289. I informed them that for that cost, I can replace it with a dishwasher that doesnt require costly service plans and yearly repairs. They informed me that their parts only have a 30-day warranty. If theyre not willing to stand behind their products enough to admit that one is faulty, then Im not willing to stand behind them as a company.

I reviewed lots of reviews, and decided that the negative reviews ones were sour grapes or uninformed customers! WRONG! Do not buy this washer. I replaced a 16 year old Frontloader Bosch! Should have had the Bosch repaired, but wanted a topload for a change, new look etc. From day 2 the washer began to squeal during the early cycle and at the end as well. Maytag repair was out for an unrelated repair on another appliance. I told the tech about it and he suggested its brand new etc, give it time to settle in.Now 4 months in and another service call to tell me its nothing!! It squeals so loud I can not run it while in the next room. I have videoed it and sent it to the Maytag repair in Glenwood Springs, and he said I should load it only full enough to see the impeller at all times!!!! Forget a full load of work clothes or a pillow or blanket. Which is to be expected to be able to wash. He said I needed to spread the clothes out manually along the outer sides of the TUB only, prior to washing the clothes! not over the impeller. I am not kidding! This is a open tub, so the impeller is the little thing in the middle on the bottom. I advised him, I videoed the event and even with three socks in it for a test it still squeals like a (well you get the idea). Trying to get Maytag help, but nowhere. Matching dryer door hinge broke first week, it has been repaired. Not good quality at all for the top of line Maytag. Then Maytag Man must be busier these days, than of old.

I purchase the Maytag dishwasher Model: MDB7749SBM from Home Depot in Plano Tx around June of 2013. The start/resume and cancel/drain button lights either flash or wont turn off and keeps trying to restart the wash cycle. I have only had this DW for 1 1/2 years. That’s pathetic! I went through the manual and tried everything it recommended but it didnt work. So far the unit still cleans dishes. Based on all the reviews I have seen on these Maytag dishwashers with the same issue, you would think there would be a recall. All the appliances in my home are Maytags and Whirlpools. Maytag and Whirlpool are now the same company. Depending on how they handle this issue will determine which appliances I buy in the future.

My complaint sounds just like the others listed here. Purchased Maytag dishwasher MDBH979SAB1 at Home Depot 2/2013. In June 2014, the control panel started to malfunction. When I called Maytag, these were the options given: 1--have it serviced out of warranty at $89-$150 for repairmans trip & diagnostic, which doesnt include parts & labor or 2--obtain something called Repair plus one, which covers the cost of repair and reinstates the warranty for one year at the low cost of $264.95. So either way, Im going to have to pay almost 1/2 of the original purchase price. Ridiculous! We had our previous dishwasher (not a Maytag) for over 13 years, with only minor repairs. We purchased a Maytag because we thought it was a reputable company that stands behind their products---well dont believe it! I would NEVER recommend any of their products.

Our problem started when the control lock button locked itself on. Called Maytag and told it wasnt covered by warranty but they did walk us through resetting the power and it fixed the problem until we ran the next load. Now when you try and set it, the rinse only light comes on. Bought the Maytag because I always believed them to be dependable - wrong!! I had a basic model Whirlpool running for a family of 5 for 25 years prior to this Maytag without ever having to call a repair person. Maytag wont deal with the issue so I would recommend to anyone else having any issues with unreliable appliances to do what I am doing - boycotting Maytag!!

Update 3/7/2018. I have been without a working microwave since 1/23/2018. Technician sent from Maytag came out to repair it and said he needed to order a new board and door switches. These items were installed on 2/26/2018 but did not solve the issue. The technician said the microwave needed to be re-wired completely and would schedule for the microwave to be removed and brought to shop where it would be repaired. After I called Maytag and explained the situation they told me they would replace the microwave (with the same model.) I called today to get an update on when the new microwave would be installed and they said not for another 14-21 days!!! After expressing my displeasure at the whole situation I was told by the Maytag representative that I could choose any new microwave model (under $399) from the lines of Maytag, Whirlpool, Armana, or Kitchen Aid. It would take about 14 days for delivery and they would schedule the installation at no additional cost to me. So now I am researching microwaves again!!! Ill update this review once the new microwave is installed.

I am not complaining at all about my dealer. I am complaining that I also am like the many others with the French door fridge/freezer. The bottom of the freezer freezes up and water pours all over the floor. I thought that Maytag was a good appliance, but also had problems with the pump and drain on my washer. Both of these are only 2 1/2 years old.