In October of 2011, I purchased a $1,199 Maytag Bravos Washing Machine. It recently started making a really loud noise during the spin cycle (REALLY loud). I had a local appliance repair guy come and he told me the main tub bearings are bad, sealer is defective and that it would not be cost effective to fix it.I called Maytag and they offered to sell me another one for $839. I am very dissatisfied that I only got 4 years out of a $1,199 machine!!! Ridiculous!! I wouldnt mind a minor repair that cost a few hundred to fix... I get that. But for it to be junk in 4 years... I have a hard time with that for the price. My appliance guy said it was junk when I bought it. Year ago, you got 15 to 20 years out of a good washing machine. Now... I buy a high end machine and it lasts 4 years. And why would I spend another $839 for the same piece of junk!!! That would be throwing good money after bad. It is not going to happen. I promised Maytag that I would post as many reviews about their product as possible... so everyone can know that they make a lousy, defective product and charge a very high price for something that will not last. Dont buy it!!

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

Bought Maytag dryer in December 2016. Worked fine for first 3 months. Then blue coloring showed up on back of drum and came off on white clothing. Had tech come out. He took pics and send to Maytag. They said it was normal. Further talks with customer service brought statements that we caused problem by drying blue jeans. Funny we never had. They just continued to say this discoloration was normal and we did something to cause problem and nothing they could do. But at least they were sorry for our problem. Whirlpool does not stand behind products. Dont buy.

This Maytag dishwasher works great if you are using as a sanitizer for your dishes so long as the dishes were soaked already. It stinks if you do not use it often and requires a lot of bleaching.

I purchased this washer... the Maytag Bravos. It is the worst clothes washing experience. I only use one cycle as the other cycles do not provide enough water to wet the clothes. It is a large capacity top loader. DONT DO IT!

I have owned this dishwasher about four years. After about three years the control panel malfunctioned and had to be replaced. Six months later I had to replace the controller. After another six months the control panel has again failed. Rather than invest more money in this beast, I have decided to replace it with what I hope is a more reliable machine. This experience has definitely put a bad taste in my mouth about Maytag products. I’m afraid this will be my last purchase of a Maytag product.

Purchased this machine (Maytag Bravo Washer) in May, 2015. Drive motor blew Jan, 2017. 18 mo. old. 10 year parts warranty and a tag on the machine that reads MCT (Maytag commercial Technology), which leads the consumer to believe this heavy duty machine. I called the warranty number, as I had properly registered the machine on the day of install. Said he would have a new drive motor out to me in 7 to 10 weeks. Yes. WEEKS. Really? I advised the operator that 3 parts stores in my area had the part available, and asked if there wasnt something we could do. He said no they are back ordered. How is it that Maytag cant get their own parts. I purchased the motor for 118.00 and my clothes are now washing again. NICE job Maytag. I suggest finding another company to buy your appliance from. Promises made are not promises kept. DO NOT PURCHASE THIS MACHINE.

Nothing wrong with this dishwasher, a bit noisy, but it gets the dishes clean and thats whats important. This was a builder grade installation and it came with the house so I cant really say its the exact model I would have selected had I been given the opportunity to pick my own.

I bought a Maytag refrigerator, model MBF 2256 KEQ2, two and a half years ago. Now the cooling coils are freezing up. I checked heater and thermostat for continuity and they were okay so the only thing left was the timer control circuit. On the earlier models, the timer control circuit is controlled by a Timer Motor or an Adaptive Defrost Timer which is separate from the main Electronic Control Board and much less expensive. On later models (including mine), the timer control circuit is incorporated into the main Electronic Control Board so if your automatic defrost quits working, more than likely you will have to replace the main board. I did not purchase an extended warranty because I believe they are useless from past experience. I bought the part on Amazon.com, received it in four days and replaced it myself for a cost of $78. This part costs $110 to $118 at Sears or a Maytag dealer.

There should be a recall. Just look at the number of people complaining about this same exact occurrence about the control panel not activating. Im on my second control panel in 24 months. Some people are on their fourth already. Give me a break. There needs to be a recall and a redesign of this thing, which turned out to be a piece of junk washer.

In September 2008, I purchased a Maytag washing machine (Model MTW5700TQ0) that had a faulty transmission. The machine was immediately replaced. Three years later, the transmission is again faulty. Maytag has refused any responsibility for repair or replacement.

Purchased Maytag Model MVWB865GW0 Ser# **, had it ONE year, circuit board and switch have gone bad, will not turn to change the type of wash cycle and the lid will not lock, which makes the washing machine not start to wash. Contacted Maytag to request a service call, per the service team the circuit board will cost $300, plus a switch $75 and Labor $100 plus tax. We will be better off buying a new washing machine! We should not have this high cost within ONE year of purchasing! Will not purchase a Maytag again!

We purchased a Maytag Gemini gas range last year in April and the extended warranty. The ovens have not worked correctly since we bought it. I never do this type of thing, however, I am just disgusted! I am going to exercise my right as a consumer to express my customer dissatisfaction and share using the social network. I dislike Maytag and even dislike A&E factory service more! I have never experienced such bad service on a new appliance. What is even more concerning and the reason I am posting this warning is there appears to be no recourse! I googled search both companies and the first things that came up were complaint pages. How sad! Buyer beware! If you buy a new appliance, research the warranty provider. It appears that Maytag has laid off the Maytag repairman and went to a lost cost unskilled service provider! A&E repairman has no idea how to fix the oven. He replaced the part. 4 weeks later, came out and walked in the house and did not even look at anything and ordered the same part again. He told us he would be back the following Friday. He did not schedule an appointment. I called on Thursday before he was due to show on Friday and A&E told me I had no appointment scheduled. They told me to inspect the parts that were shipped. I told them I would not even know what I was looking at! They told me the repairman would be back out between 1-5PM on Friday. No one showed. At 2PM, I called and A&E said the repairman must be on his way because he did not call and say he wasnt coming. But again, he did not show! I made no less than 6 calls to A&E and Maytag after that! A&E would not escalate the situation to a supervisor and on call number 6, when I finally got to an advocate, they told me to call Maytag! I have taken 4 days off as vacation to be home for the repairs and this last day was the final straw. When I researched escalating paths for both companies on Google, the first thing that came up was whole pages dedicated to complaints for both companies!

Neptune Washer: Tears clothes at random intervals and their help desk asks for money.

I have a new HE (high efficiency) washer. It takes getting used to as its a definite change from the old agitating system but I think I like it. It doesnt make much in the way of suds but everything still comes out really clean. The wash cycle is much longer than my old washer but it uses a lot less water.

Maytag dishwasher quit working 3 years old. No power. Control panel dead. Piece of junk product.

We purchased a home one year ago. It has all Maytag appliances that were anywhere from one year old to two years old. The Neptune LE washer is not working as of today. This washer is supposed to be the top of the line, and because it is almost three years old, it is no longer under warranty. This washer will fill with water but does not spin or rinse the clothes. We paid a lot for this home and were so happy to get appliances that were all practically new. Now, we refused to have a repairman come and charge us lots of money to fix a washer that should not be broken. I have had washers run for 15 years and that was when I was washing clothes for 6 people, including cloth diapers for triplets! I will not buy any Maytag appliances. I will be getting an Amana or a Sears brand. Please, no one go buy a Maytag appliance.

We have had this washer for 1 year. I noticed right away my clothes would come out extremely wrinkled. Now not only are they wrinkled, they also smell musty. After researching I find others have the same issue, even finding a video of horrible mold under the drum. We called to have it serviced since we have a 5-year warranty. The service man recommended using Afresh. WELL, we do faithfully every month. He said they would not pay to have it cleaned, and even if he cleaned it, that the mold would come back. This to me is a major design flaw, one that could potentially make people sick. IF there is that much mold growing in the machine, with no way of cleaning it, and now the clothes are smelling, there is a HUGE issue!

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

We first purchased a Maytag Neptune washer and dryer set. We loved them. Had them for 15 years with no problems. When we decided to get a new washer and dryer, we were loyal to the Maytag brand. I was immediately drawn to the Maytag Bravos XL due to the extra large capacity. What a mistake! This washer and dryer pair take more than two hours to complete a single load of laundry. It often takes more than one wash to get clothes clean. If you wash an extra drum large load of laundry, often times there is not enough water and agitation to even get all of the clothes wet. I have a one-year-old boy and a six-year-old boy, their clothes get very dirty. This washer Does not get food off of my one-year-old’s bibs. And my six-year-old’s clothes come out looking as if they haven’t even been washed. What a disappointment! My husband and I are going out today to purchase a new washer and dryer set after having just purchased these Maytags in April last year. What a waste of money! Please include me if a class-action suit it’s taken.

I purchased the Neptune HE pair because they are front loading and can be set on pedestals to raise them to a comfortable working height, plus the brand and reputation are both excellent. I like that the chimes can be adjusted from low to high, or turned off. The front loading washers clean so much better and with a lot less damage to items than washers with center agitators. Looks are secondary, thats for sure. Functions like warm/warm cycles and being able to adjust to whatever load needs to be washed is really most important to me. Any appliances with a good, proven track record of reliability with few repairs is high on my list. Expensive appliances should be made to last and be of durable quality! No cheap plastic or weak-looking welds or components, thank you! Quiet operation and dependable cleaning and drying are top in my book, and this pair has exceeded even my picky expectations in total overall performance. They are 11 years old now and look & function like new! I had one minor repair on the washer at 5 years, and not a single problem since. With front loading washers, its important to keep the door open a little when not in use so that they dont get a musky smell. Ive gotten into the habit of using laundry boosters to help clothes, sheets, and towels smelling fresh longer, and putting a small amount in the washer drum has kept my whole laundry room smelling nice. Purchasing the pedestal drawers to set the washer and dryer on added extra storage to my laundry and its much easier for me to load/unload them at this comfortable height. Im totally spoiled by it now, so when I use someone elses laundry room (when I visit) I am reminded how nice my own setup is.

I purchased a Maytag refrigerator (MBR2258XES4) from Home Depot in 2012. I bought a five year extended warranty. It started leaking at the bottom. Repairmen said defrost drain clogged not covered! Cost: $180. DO NOT BUY MAYTAG, N.E.W. (Asurion Co.) warranties or Home Depot appliances! This is text book deceptive advertising. At no time did Home Depot associates in Kitchen and Bath departments say that this common design flaw existed and that it was not covered under the N.E.W. Asurion warranty which cost me an an additional $150.00! I am interested in joining a class action lawsuit against Home Depot and Asurion Co (N.E.W.) warranties.

This is was my first time experience to purchase Maytag Bravos XL (MWWB835DW) 5.3-cu High Efficiency Washer. I need it fast replacement to my front loader Samsung washer as it was recalled and had mold issues. I was looking for a High Efficient and Star Energy digital, glass top reliable machine. I may say that I was fooled by advertisement and promotion from the Advertisement and promotion from Home Depot. I did not know much about Maytag Brand but I was convinced by sales person and price promotion. Big Mistake! Huge! I am extremely dissatisfied with this washer, it doesn’t use enough water to cover the clothes! No matter which cycle you use, the clothes don’t come clean.I wash and re-wash my clothes and ending up paying huge water and electric bills as I have to use deep hot water wash each time and after rewash again! Not so High Efficient! After using this machine for just over 6 month all my white expensive towels turned gray and all my whites is no longer white. This washer ruin my clothes. Another problem that this machine doesn’t have small load quick wash and if you have a small load it will go through 50 minutes cycle and I still need another wash after all! If I would wash my king size comforter I still have to do it twice and it does NOT rinse all the water out! I thought I can do big load but this machine cannot handle big loads!My laundry days became a nightmare! I would not call this machine High Efficient at all! Company does bogus advertisement just to fool and attract consumers. This is terrible washer which make me think how possibly this machine is on the market and allowed to be sold? I did not notice problem till very late and I missed my 90 days return policy. Now I have to find another replacement. What a waste of money! I do not recommend this machine to my enemy. Please read reviews before buying this horrible machine. Do not miss your 90 days policy returns. Save your water and electric bills by avoiding Bravos XL. I am hoping that Consumer Protection will step in and evaluate numbers of complaints and will help those who were fooled and ripped off by such a false advertisement.

Maytag Bravo 300 Quiet Series - Bought this Maytag 5 years ago because Ive always had good experiences with them. After 3 years it started making rattling sounds so we had someone come out and fix it for around $275.00. 2 years later its still rattling, leaving black grease marks and putting holes in the clothes. Will not complete cycle unless it is unplugged, reset and plugged back in. I give up, I just bought an LG. I will never buy another Maytag washer again, still have the matching dryer though.

Bought the Maytag top load high efficiency washer (also matching dryer which works perfectly) brand new less than 6 months ago. It is the worst. It leaves swirl marks on my clothes that doesnt come out. Leaves part of clothing dry without being a large load! If I put sheets in there it blows up like a mushroom and leaves that part dry. I use the correct detergent. I had a serviceman, that the manufacturer suggested, check it and determined there is nothing wrong with it which only leads me to the conclusion that it is a poorly designed product. Spoke to a manager at Maytag that said the machine works fine. And because it is in a business setting there is nothing they can do. (What? If it worked fine, I wouldnt be here.) Called to company I bought it from... Theres nothing wrong with the machine plus we are closing the business so its the manufacturer warranty that you need to call them. I would have been happy with a exchange. Poor design, poor customer service.

I made the mistake of buying a Maytag 2 years ago, this machine would not wash clothes even when using the deep water wash. I should have looked at it closer, it is so full of modern computer garbage that I was having to wash clothes twice so the water saving was negative. I own a business across from a major shopping center so what we did was we loaded it up in one of our trucks and parked it in front of our business with a giant sign and invited people to take a look before buying one. In 6 months we must have had at least a 1000 people inquire.

Purchased this Maytag dishwasher from a local Home Depot in Feb. 2014, no problems until now in late July 2015 (about 18 months). The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond.Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, can not be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only about three days ago. I assumed user error so let that cycle run, then was able to choose a different cycle (cant remember which one) which also completed. But since then the control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem, so will probably replace (with something other than Maytag) rather than repair.

I bought a Neptune washer and a dryer. I have had nothing but problems with these items since I got them. My washer keeps giving me a 3e code and will not clean the laundry right. I have used the H E detergent it requires and yet my clothes stink. My laundry smells like mold and mildew. I now dont have my units to wash and dry clothes. I paid almost $4,000.00 for the pair. I dont have the money now to replace them.

We have had this washing machine almost 1 year and the small problems have grown enormous. In addition to the constant soap residue left on the dark clothes (my guess is its on the light clothes too, but you just cant see it) the washer goes out of balance frequently (they are replacing the suspension, after they said its all working great). The repair man said Im not loading the clothes properly, I need to roll each item of clothing into a ball and then place it in the washer. Are you kidding me, my new machine has special needs? And dont put in too large of loads. What!!! Its an XL capacity but I cant do an extra large load, because half the clothes wont get wet or clean. Maytag blew it big time with these models, I could talk about the dryer too. Maybe next time.

It took about a year for the problem, which turns out to be an extremely common problem, to start. The build up of water in the freezer due to the clogging drain. Maytag needs to step up for the consumers that purchased their defective product. I have cleared the ice and tried to clear the drain three times only to have the problem return. I refuse to pay someone $300 or more to repair this. This is crazy and unfair!

Within a year of purchasing this washing machine, I needed to schedule a repair service because the washer started making an unfamiliar noise. Repair Service shows up and refuses to touch my washer. The ink on the Serial and Model number (stick on label) inside the washing machine door has washed off. Sticker label in excellent shape, except all the ink has come off. If the Repair Serviceman cannot read the label, NO SERVICE FOR YOU. MY SAGA... Did you know that if your washer or dryer does not have a readable serial number on the machine, NO repair service will work on it. It does not matter if you have all the paperwork showing this information. If the original label is unreadable, no repair service will touch it because they will be fired. Maytag changes parts on a model all the time. The serial number is the ONLY way a serviceman can tell exactly what parts your washer was made with. Apparently the serial and model number label sticker was not printed with permanent ink. The Repair Service said the Serial and Model number ink washed off the label because the sticker was incorrectly put on the inside of the washer door at the bottom. But they were WRONG! Maytag shows online that is exactly where the serial and model number sticker is supposed to be located. So, I called Maytag to order a new serial number (stick on) label for our washer. I gave Maytag the information and I was told I would have the label in two weeks. Then I called back a week or so later to make sure the serial number was ordered and on the way. Maytag said there was a misunderstanding, and that they received my request on 6/17/15 and it was sent to the ONE AND ONLY GUY that makes replacement serial number tags and he was sent my request on 6/22/15. Maytag said it would take the one and only man quite some time to make the label (SINCE THERE IS ONLY ONE!!!) and I could expect to receive the replacement label in 4 to 6 weeks and they were sorry, but there was absolutely NOTHING they could do about it. So as my year old washer sits for over a month, Im going to the Laundromat each week. We should have received the new serial number on August 6, 2015. So it’s taken almost 2 months and my label is close to two weeks late. To date I have not received my serial number. I tried to use MAYTAG chat, dont bother, they said they couldnt help me. I needed to call in. So I emailed Maytag today for their support services to tell me WHEN I can expect to receive my new serial number label. I bought this through hhGregg. Check your Maytag washer. IF THE SERIAL NUMBER AND MODEL NUMBER LABEL ARE INSIDE THE DOOR, CHECK TO SEE IF THE INK IS COMING OFF THE MACHINE LABEL, and order a new one NOW if it is, or you will not be able to get your washer serviced. Do not put new label back on the inside of the washer door. This is just unbelievable.

Maytag bravo - thought it would be a good brand/buy/new technology. Absolutely nothing to like. Complete junk. Bought it in June 2013. Doesnt get things clean and takes a long time to not do that. We thought a good reputation from a major brand would mean a durable efficient washer with a reasonable capacity and good features. Unfortunately we didnt know when we bought it what a bad design/investment it was. It has destroyed numerous garments with fraying and doesnt rinse soap or dirt out because it doesnt use any water.The bravo from Maytag is supposed to be low water efficient. Unfortunately, it doesnt use enough water to wash clothes, no matter how little or how much HE soap you use. It frays clothes, leaves soap residue, wont wash jackets or blankets or bulky things, takes forever to NOT get things clean, doesnt get heavy stains or mud out, the list goes on and on.... oh, and its expensive, and breaks down a lot. I cannot believe that there has not been a government recall where the people who were unfortunate enough to buy one have been given a large amount of money back.

We bought a maytag dishwasher three years ago. Approximately nine moths later the control panel went bad. They came and replaced it. Approximately six months later they came again and replaced it. Approximately a few months later it went bad again. I complained to Home Depot and they replaced the dishwasher. Too bad they would not change the brand. Guess what? Here we sit, not quite two years later and again the control panel went bad just past the warranty. The cost to repair almost $470.00. Paid $525.00 for the dishwasher in the first place. I regret ever leaving whirlpool. Our first very heavily used dishwasher (whirlpool) lasted 11 years no problems.

Clothes are never submerged in water. Clothes come out worse than when they went in. Every review and complaint mentioned is dead on! This Bravos XL is a piece of crap. Stay away from lying salesmen from HH Gregg. And stay away from Maytag. Perhaps we should all get together and file a class action lawsuit! And donate all monies, washing machines and dingy clothes to charity!

Our refrigerator is just 2 years old and it have been leaking for over a year. It started leaking right when the warranty expired. I am so mad. I called them and they said... You can purchase a warranty for $400. I am like.... what!!! I called my home warranty and they fixed it for $100. A few months later it is leaking again! I am so mad... It is a $1200 refrigerator. What can we do as a group to fight for this? There have to be something that we can do?? It is so frustrating. If there is an attorney that can take care of this group that would be great.

Bought brand new coin op washer and dryer. Washer had problem from day one. Took in for repair. Maytag warranty covered parts, no labor. Cost me $100.00 on brand new $900.00 washer. Last money they will ever see from me.

We bought the Bravo XL set 11 months ago and the washer leaks all over the place.. Called Maytag and had the repairman show up. Upon arrival he told us these were the worst machines to buy and would never recommend to anyone. He also said that business has been great due to all of this.. He checked the washer and said the water pressure was too high and lowered it. He couldnt find anything wrong with it. After he left I started a load and sure enough it was the same. Called him right back and he said to call Maytag because he was going to another repair job. I called Maytag again and they said to call the repair guy.. Never again will we ever buy Maytag.

I would say you have plenty of options when choosing a color for your dishwasher. You can choose black or stainless. Try one today you wont be disappointed. I load plenty of dishes into the space. It has extra pockets for little things and it has plenty of hooks and hangers to use for bigger cycles. Kenmore Dishwasher runs great. Very efficient and cleans the tough stains better than any dishwasher Ive ever used. I would recommend this to anyone looking to buy a dishwasher. Of all the dishwashers I researched at Lowes and Home Depot and Sears and Ace and other local stores, the Maytag was the lowest price with all the features I wanted.

MFF2558VEM0 - Had the same problem repaired less than years ago.. Now has the same problem. Looking for a new fridge. Hope better luck this time.

My family purchased a New Maytag Washer and dryer about 1 1/2 years ago! Thinking that the name was far more Superior than anything we could afford! What a piece of junk! The washer is nothing but flashing codes! Unlevel this and always stopping and starting over with a wash, when in fact it doesnt shake and bounce itself into the middle of the floor! As best as I can describe, it literally needs Hurricane straps to hold it down! You can never wash a full load because it cant handle it! Now! Onto the pathetic dryer! Several weeks after they were installed was the first scenario with the dryer! We had a representative that does work for Maytag warranty to come and work on it, after telling me over the phone that if in fact the lint trap had lint in it, that I would have to pay the service call! Funny!! So after diagnosis he said the belt broke that runs the exhaust fan! He said it was fixed and went on his merry way! Several months down the road! Same routine! Broken belt that runs the exhaust fan! And once again several more months down the road! Guess what!!! Yep!! Broken belt that runs the exhaust fan!!! So now here we are! I am now into the extended warranty that I purchased from the furniture store which was almost an additional $250.00! And voila!!! Its broken again! So being the fed up person that knows what the answer is going to be, I take the front off the dryer like I have seen done so many times before!!! And what to my surprise do I find?? Another Broken Belt!!! So I am wondering!! Why so many broken belts! So I take my flashlight and look at the motor and housing that holds the exhaust fan and I notice that in fact the housing that holds the exhaust fan is BROKEN! Therefore, this is the cause for so many broken belts!!! Well, who should be responsible??? I contacted the extended warranty people! What a waste of time! After setting an appointment for Sears to come work on the dryer and after explaining on several Recorded Phone conversations what has taken place! The service man comes to my home and not even 1 minute after entering tells me that he cant work on it because I have self diagnosed my dryer! What was the purpose in me explaining to them beforehand what I found??? Why didnt they mention then that I should not have taken it apart or hey put the front back on!!! Now after causing a ruckus with the furniture company that I have spent well over $50000 with!! They want to supply me with a 1 time Customer Courtesy!!! Of repairing the dryer!!! Oh did I mention that I am a Professional Diesel Mechanic for a major Trucking Company that is far more capable of diagnosing something like this than evidently the person they sent the first 3 times!! NEVER AND I REPEAT, NEVER BUY ANYTHING MAYTAG!!!

Had a Maytag Dishwasher that was recalled in 2007 model # DWU9962AAE. I was sent a notice of recall and when I contacted the Maytag staff in the Recall department said that they were sending out a replacement as the unit. Mine was being recalled due to defects in the heater element, which could cause electrical failure and fire. I was pleased they were offering to replace the unit, and within a week or so, a new unit was delivered. This is where the troubles began... the delivery/install person from a local retailer, complained the entire time about having to do this job, was ill-equipped to perform the install, twice he thought he would have to stop as he did not have the correct tools he shared with me. I felt this was odd, if this is the job he did all the time? I asked for a bill of sale or something that would show that this unit had a warranty, and date of install. I was told that in these cases, the local retailer that is contracted to install takes care of all that. I did get the Dishwasher use and care guide, and it seemed like new unit. I had never had a recalled unit of a major appliance. Also since Maytag had my address, phone and email information as they set the install up. I believed the installer. Fast forward to about 2009 and the control panel on the door starts to lose cycles. I decided that since it was just me using the unit and the cycles I used most worked I would not bother with the repair.Fast forward to late October of this year 2015. The dishwasher Maytag model # MDB9601AWW finally does not turn on any longer... I call Sears to have an estimate for repair of the circuit board in the door. I give Sears the model and serial number... and schedule an appointment. The repairman gives me a cost of roughly $600 to replace the circuit board in the door! I tell him no thanks pay $ 59.00 and decide I will buy a new unit... I review many sources such as consumer reports, where it becomes evident that Maytag as a brand is not very reliable. At that point I decide to call Maytag and speak to them about my issues. Two dishwashers in very short order have issues. Also my new unit only had a one year warranty.So much to my surprise when I called Maytag I was informed they did not have any records of my contact information at my current address..? And worse there was a recall on my current dishwasher back in 2010! I was never informed of this, and had used a potentially hazardous appliance for 5 years with no knowledge of this! How could that be though since I was given my current unit by them in 2007. I was very unhappy at this point.... but my disappointment with Maytag was about to deepen.I was also not happy with Sears Home Repair.... They are informed about all product recalls, and had my model and serial number. When those were entered into their computers when I made the appointment and again when the repairman came out and captured that information on my dishwasher himself that should have alerted him to the recall. Not an opportunity to sell me a $ 600 repair that did not even address the defect for the which the recall was issued.So I am now routed to the Maytag recall department.... where all they offer me is a $ 150 coupon for an expensive Maytag dishwasher? So after explaining my situation... and asking the woman I was on the phone with If she would invest $400 or 500 more dollars in Maytag dishwashers, given my experience with 3 failures of their products in two separate units that were not that old? She said she understood. She arranged for her manager Carol to call me the next day at 9:00 am PST. The call never came, and two hours later when I called in they tried to tell me it would be another 24-48 hours before she could return my call? I was now very unhappy. I asked to speak with her supervisor Tim. He too was unavailable, finally after a very long time waiting on hold. I was connected with Amber. I explained again my issues and told Amber that I would like another Maytag Dishwasher to be offered to me..... as this was a very unique set of circumstances... She was willing to let me write letters like this and contact the Consumer Products Safety Commission and lodge a complaint. I am waiting to be contacted by the manager that handles recalls from Maytag. She alleged that they CPSC does not allow the Mfg to assign specific compensation to individuals. That is true....when they are only subject to one failure as part of the recall.... according to the woman I spoke with at the CPSC. However I had not only that complaint; but the circuit board issue and as goodwill gesture to any consumer they (CPSC) have no jurisdiction.... and Maytag could do as they wish. However I doubt anyone but Amber a low level manager, who took it upon herself to make this decision on her own, without even punting to her boss Tim when I shared my story. I just this last weekend bought a new Bosch dishwasher.... and would caution anyone who was considering the purchase of any Maytag appliance of any kind to use my experience as a cautionary tale.

I called Sears to have a simple repair done to my Neptune washer and received a quote for $800.00++. They gave us a coupon to get a new washer at Sears and we did. Last week my dryer broke and I looked the repair up on Youtube. It looked real simple. A quote for $270 was given to us. Again a coupon if we wanted to buy new. It seems to me Sears jacks the price up on its parts and labor in order to push the customer to buy new. So far its worked for them and Im sure everyone else as well. Its not going to work out for Sears this time. Im no longer doing business with them and I will do the repair myself. I still got stuck with the service call but that will end as well going forward because I know now what the game is. Shame on you Sears. Double thumbs down for my Maytag Neptune washer and dryers.

After 15 months of use the Maytag Dishwasher MDB8959SBS2 the control panel start malfunction. I read very carefully about the Home Depot Customer reports before purchasing this built in stainless steel dishwasher, and supposed to be one of the top notch on the market, around $850 retail price. It becomes a big disappointment. After three months of use, the top rack handle broken but it still under manufacture warranty, so we get it fixed by Maytag contractor. Then 15 months after regular use for a family of five, the control panel start malfunction, few bottoms will not start anymore. We are out of luck with one year manufacture warranty and working towards our VISA card extended warranty to try to get it fixed.

When I attempted to contact Maytag about an issue in my 3 month old washer all I received is an automated email back saying to contact one of the repair places on their website. There was one, so I notified Maytag I would contact them. I contacted them. They said Maytag had not notified them that this was a warranty repair and if I wanted them to come out I would have to pay for it. I have attempted to contact Maytag several times to get this straight. Guess they are trying to wait out the warranty to respond. Will NOT EVER buy another Maytag. Too bad they used to be a good product.

I bought a Maytag washer from Lowes and bought the extended warranty. The warranty expired but Maytag is not taking responsibility for the lemons that they sell. I have seen many reviews stating that the bearings went on the washer. This is what happened to me and it happened twice already. I spent 798.00 on this washer thinking it would last for more than 6 yrs. They offered me a warranty for 368.00 or to purchase another washer at a discount price. Of course I refused but I want everyone to be aware of Maytag Washers - not worth the money.

I was told to at first to just leave the door open, then when that did not work I was told that I should bleach my machine at least once a week which I did. That did not work either. Then I was told to buy the product REFRESH and that would take care of the smell. That did not work either. So I am at my wits end with the stench of my clothes.

Same problems as everyone else. Water not soaking the clothes, questionable load capacity, shaky (we have engineers in the house so there is no way they did not look for floor evenness as the stores/Maytag will tell you that you may not have done, complete bs) etc. Its absolutely horrible that were all now stuck with such a terrible machine. I really wish I had read these reviews before (I googled the machine earlier but got generic stuff and didnt stumble upon these reviews until much later). Maytag should take responsibility on this as retail stores do not take back appliances unless they are defective. The Bravos is definitely a defective product from the get-go though.

We bought the washer less than a year ago. The washer became off balance with an average load of jeans. The washer shook so violently that it cut our floor, busted our wall, and broke itself. Water covered our floor! We have now been over a month with no washing machine (still paying on it, by the way). We have had to pay to get our clothes washed in the last month = EXPENSIVE! The repair company has been out to our home twice, broken high-quality tools trying to repair the machine, and told by their higher-ups that the washer can still be repaired. Customer service only tells us that we have a repair warranty and the first repair has no time limit.

I purchased a Maytag stainless steel French door model the middle of 2006. While cleaning the French doors with the cleaning product given to me with the purchase of the new fridge, I notice what looked like coffee on the doors. It wasnt, it was rust on the stainless steel doors. I called the service tech and they came out. Rubbing the fridge, he told me it wasnt rust. He took a closer look and found that it was in fact rust. He called his office; they told him that rusting on the doors has been an issue lately. He charged me $65.00 for what I already knew. I called Maytag and it took a while, but they decided to send new doors. However, I had to have a Maytag rep install it, which would cost me. I didnt have it done. Two years later in 2010, the French doors felt hot to the touch and the inside was warm and not cooling. The freezer was fine. I called for a tech to come out and it’s another $65.00 to fix a fan motor that blows cool air from the bottom to the top. Oh, it’s not under warranty because it wasnt inside with the motor. Total cost: $235.00. In 2010, I woke up and opened the fridge to get milk out. It was warm and so was the inside of the fridge. I thought it was the same problem, but the freezer also was warm. Upset and not wanting to pay for this again, I unplugged the thing and started using a little fridge that I have stored in the basement. It has no freezer. Today, I finally got over being pissed and decided that I would have a tech come out and find out and finally fix it. The tech said that the compressor has failed and it would cost $790.00 to fix. Im not having it fixed, so it’s another $65.00 gone. The tech said that the compressor in Maytags/Whirlpools has been a pretty big issue lately. All I can say is that I will not ever purchase Whirlpool products again. From inside to the outside, this product has been unsatisfactory. I just noticed that the rubber is failing on one of the French doors. Wake up, Whirlpool. Model number is MFD2561HES.

This is the WORST washing machine I have ever had. You cannot control how much water goes into the machine and the clothes being washed are not even covered by water. They stick out above the water at least a few inches!!! How can anything get clean if no water is touching it! I even add water into the machine at the beginning with jugs of water just to cover the clothes... the machine automatically gets rid of that extra water and when the wash cycle comes on again the clothes are not submerged! I paid A LOT of money for this awful machine and Maytag needs to do something about it! And, yes there is a sticky gummy substance on all the dark clothes! I even put clothes in the washer with a dirt spot on it purposely and the spot is always there when the wash is done. Nothing gets clean! DO NOT BUY this machine... you will be very sorry!!!

I have a major complaint with the Maytag double oven design. With the smaller oven above, if you spill any liquid while taking something out of the top oven, the liquid drips down between the two panes of glass on the lower oven door. This makes it impossible to clean. Maytags reply - call a service rep and have him make a house call and take the door apart for you and clean it. Not warranty work so I would have to do this every few months. Also, when baking in the upper oven, cakes and cookies tend to overcook on the bottom as the dishes are so close to the element.

I bought this machine because it has a (deep water wash), which means there is a lot of water, enough to cover the clothes, at least I thought so, the salesman seemed to think so as well! But no, it does not come close to covering the clothes, false advertising! I must put my clothes in a large bucket, soak the clothes with water, then bring the bucket to the washer and empty it into it, because of the weight of the water, the machine adds almost enough water to cover the clothes.Another big problem with this washer is the fact that if I lift the top in mid-wash, while I do something, not wanting to listen to the irritating sound it makes in my apartment, after 10 minutes it starts to drain and there is no way to stop it, I must wait until it completely drains and restart the machine. This machine has the stench of government on it!!! My advice, keep your old machine.

Always have bought Maytag. 16 years on both washer and dryer. The newer models, which I dont have, locks the top of the washer after it starts. I would hate that. I dont care if they are stackable but I would want full size. I dont think I would pay extra for a front loader, but the only front loading washer I have ever owned is small and at our camp.

Purchased a new top loading HE washer in 9/2012. This machine gets very little use - approximately 10-12 loads a month. It is now broken awaiting parts which will cost about $200. Of course the warranty is only good for 12 months There is no excuse for a washer this new breaking and costing this much to repair. What a piece of junk! Avoid all Maytag products.

Purchased a Maytag Electric range Model MER8800FZ2 in 2019. The surface Scratched the first week of purchase and the stains will not come off. When I called customer service they claim they are not responsible for cosmetics. In my opinion, This model was put together with the cheapest material they could find. Maytag is not what it used to be. The Elements take a long time to heat up. Inside the oven, the Glazed Paint is cheap product also where once it stains with food it never comes off.

We purchased a Maytag Commercial Technology washer from Lowes. After having the washer for only 3 months, the drum failed, an entire load of clothes was turned black with oil, and my washer was out of service for months. The drum had to be replaced. They did not offer me a replacement. I was just without a washer. They couldnt get the parts because of supply issues created by Covid. I was offered a 2-year additional warranty which should have carried me through 2022. Last week, I called to use the warranty - service was scheduled (and I was told that I did indeed have a warranty by the service team.) I was then told by the repair team that I was out of warranty. Maytags notes show I was only offered a 1 year additional warranty. I talked with Management at Maytag/Whirlpool - they will do nothing for me. Shame on me for not getting that in writing. Shame on Whirlpool/Maytag for lying to me. The washer has been a nightmare! Dont buy one.

We purchased this model from Home Depot in February 2011. In July 2011, I found it full of water and dirty dishes after running a wash cycle. It was completely dead like it wasnt getting any power. I checked the fuses, etc. - nothing was wrong that I could find with the power supply. I called for a service tech that day and they sent someone out to check it. It was the control panel. They shipped me a new control panel and the tech came back to replace it under warranty. It worked great until July 2013. Again, it is full of water and dirty dishes, wont turn on and has no lights on the front panel. I called Maytag to get a service tech. The warranty is expired of course. They offered to sell me a replacement dishwasher at a discount for $409, Model # MDB7749SBW. Or I can buy an additional 1 year of warranty for $269. I also could buy a control board for about $150 online. None of these options is attractive right now, but hopefully if I get the new model, it will not have any issues... I wish they would just tell me it was a crap unit instead of giving me the option to either get a new one or pay for a useless warranty. I am fed up with this dishwasher. 2 control boards in 2 1/2 years is unacceptable and indicative of a defective unit or design. After reading the reviews here it appears to be a defective design.

I have never given anything a negative review before, but this, by far, the absolute worst appliance I’ve ever had in my entire life. I bought it because I had an old leaky washer, but I’d take it back in a heartbeat because it could ACTUALLY wash my clothes. We spent a lot of money on this washer because we wanted something really nice that would actually work, but this washer is no better than me throwing my clothes in the sink and turning the water on. I’ve tried every kind of detergent and pretreatment that I could possibly try, and nothing helped because the actual machine don’t do nothing. Shirts come out still coated in mud, and half the load is dry??? Please, save your money, get your washer somewhere else. And I hate to even give this thing 1 star because it ain’t even worth that.

We purchased the Bravos XL Washer (top loader) and dryer about a year ago and have had issues with it since it was installed. Please note, we live between two homes so the machines are not heavily used at all. Our $250 machine we have in our Florida home works a million times better and is several years old. We purchased at the ABC appliance store and they have sent out a technician 4 times in the first few months. Bottom line, these are just pieces of crap machines. They cannot be returned! It is really a shame for the money spent and your clothes does not get clean on any cycle. The technician told us we should use the Deep water wash for all cycles which still does not work. I bought this machine for the XL capacity but also for the delicate cycle and stains do not come out, undergarments are still dirty, white power residue from OXI is left on the clothes etc... DO NOT BUY. This would get zero stars if I could. So disappointing and frustrating. If class action suit does happen, I would want to be part if it.

Purchased a Maytag French door freezer underneath refrigerator 8 years ago. It stopped working because of the circuit board located behind the ice and water compartment on April 7th. Contacted a Maytag repairman, which is a whole other story. Had to order the part, weeks and weeks go by telling us the part is coming. Then a call came from the repair man on June 17th, Maytag no longer makes the part. Meantime we located the part by taking the fridge apart ourselves and ordered it arriving today June 19th. Contacted Maytag - Whirlpool corporate. Answer, We are sorry we no longer make the part, and basically told me after spending $2800.00 8 years ago Im up the creek without a paddle.

We purchased a Maytag refrigerator, model #mf12269veb on 2/1/12 and for the past few months it has been leaking water out of the bottom freezer unto my floor and ice is forming inside the bottom of the freezer. I have read many complaints about this and if there is any recourse to this problem please let me know. So disappointed with this appliance.

I owned a Maytag Bravos top loading washer for 8 years, and I loved it. It caught on fire while washing a load. Thank God I was home or it could have burned my house down. Just wanted to post this somewhere to issue a warning.

Bought brand new. No deal, not on sale, not a return. Just heres money... give me working washer. This thing doesnt wash anything. It leaves soap all over the clothes. When you turn it on and wait til it starts washing, look in there with the lid open... theres barely any water! The clothes on top stay dry! The only way to wash your clothes in it is to add three-3 gallon buckets of water at the start of each STAGE of EACH cycle! My wife showed me after three months of washing clothes like this. Anyway, to the garbage with this and back to Whirlpool basics with me.

Washer water level sucks low at max levels kept freezing. Bought mtw7230. Its junk agitator doesnt rub good. Not like dual action agitator and when I start cycle says 34 min but I timed it takes one hour. Same goes to 1:30 to 2 hours takes 10 min for water to pour in spins for nothing. I sent it back. 965 I paid.

Purchased a Maytag MDB4949SHZ dishwasher new from Home Depot in January 2018 as part of an extensive home remodel and addition. Did not move back in permanently until late June 2019, so the unit was not used at all until then. It quit working in January 2021 and our local (Sandpoint, ID) appliance repairman diagnosed a bad motor and pump assembly (the main functional component of the dishwasher). The unit was marketed as having a 10 year warranty and based on past experience with older Maytag appliances we purchased it. The fine print reveals that the 10 year warranty applies only to components that are unlikely to ever wear out or fail; all the rest are covered by a one year warranty. Part cost is over $200 and does not include installation. Maytag customer service (45+ minute hold to speak to a live human) of no help. No way are we throwing good money after bad to fix it. Lesson learned; just purchased a Bosch.

A lot of repairs in 6 years from belts. It leaks water around seal on door. Only part of the cycles work. I would not recommend the Maytag washer to anyone. When I got it I expected or hoped it would last 10 years or more.

The machine can clean even king size quilts, and clothes come out very clean. It is a front load and there are no problems with odors. There are many cycles to choose from. Cycles spin gently enough while getting out most of the moisture.

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

We purchased this machine (Bravos XL top load washer) in August and its been nothing short of a disaster. It doesnt clean anything. Within two washes my cloth diapers were unusable, loaded with ammonia and stains. Our camping clothes wreaked of smoke. I tried multiple cycles, more detergent, less detergent, larger loads, smaller loads. Doesnt matter. It doesnt clean. I called customer service within a week and waited 6 weeks for a service call. Into third trimester of pregnancy and recovering from an MVA, I was washing soiled clothing by hand in bathtub desperate for help. I only wish Id known about their 30 day money back guarantee. After many calls, no shows and cancelled appointments, the first tech comes. He tells me the machine is fine. They just dont clean well. Hes not surprised. I call the appliance shop, they said the same thing. That they wouldnt have sold me the machine if they knew I had dirty laundry to wash. (Who washes clean laundry?). They wont help us. We call Maytag back. They send another tech. He says the same thing. Tells us to keep complaining to Maytag. I call again and they tell me that if I want a service tech, I have to pay. Theyve deleted all my feedback from their social media site and refuse to provide any assistance. The machine is nice looking and makes big promises but thats where it ends. Save your money. Youll get better results with your grandmas washboard.

Purchased my Maytag in November of 2010, with the freezer on bottom. Within 1 year the ice maker stopped working, and every 8 to 10 days it gets a sheet of ice on the bottom, and water runs out all over the floor. Guess, Yes the warranty expired and scared to death that Im gonna have to replace my floor. If there is a class action suit out there please inform me.

The design capacity of the dishwasher is not conducive to cleaning a full load. Within 3 months of purchase one of the interior baskets broke. I will never buy another Maytag product again. I was a fool in believing this was a top of the line dishwasher.

I own a Maytag MDB9150AWB dishwasher which isnt covered under current recalls. Yesterday, I heard a loud pop sound, and it stopped working (also popped the circuit breaker). After taking the door apart, we found burnt wires at the bottom of the door close to where they bend to go under the dishwasher.I called Maytag to find out if they would do anything, since this seemed like a defect in the materials used. They wont offer anything!

We bought a Maytag dryer from Lowes on 4.23.20 for $567.87. From Day 1, it required us to dry even medium loads at least 2 times and sometimes even 3 times. I have been complaining to my husband since we got it. The clothes come out smelling almost burnt. But if you dry it once, the clothes are wet. And if you try to dry it the 2nd time for less time, its still not dry. So, it takes forever to do laundry. This morning, it sounded like a lot of metal was rattling around. So, I looked inside to see if change was in there, and nothing was in there but t-shirts and socks. It had been drying for less than a minute, but when I opened the door a wave of extreme heat hit my face. Now Im afraid to use it because I think it will eventually burn our house down. And with COVID-19, we do tons of laundry. We cant afford another dryer but may have no choice.

We received a MayTag Microwave on Saturday May 10, 2014. There was a minor ding in its case, but it did not show any other damage. After installation I tried to use the microwave. It did not work. So on Monday the 12th I called 800-688-9900 for service. A service appointment was scheduled for Wed May 14th. The service man told us the microwave could not be fixed and had to be replaced. I asked who should replace it. He told me to take it back to the place of purchase.I took it back to the dealer and after a lot of discussion it turned out that MayTag had to replace it. I was given a case number. I called Maytag and was told replacement could take 4 -3 weeks. I could purchase a new microwave and have it by Friday may 16th much sooner than Maytag could do.

I bought a Maytag Bravos XL washer in 2017 for around $800 which suddenly stopped working about 1.5 weeks ago. The console wont turn on. I filed a service request on Maytags website which results in Maytag subcontracting the job to a local appliance servicing company. About 10 days later the appliance tech shows up to my house. I had to pay $125 to the service company for the technician just to show up. After, he tinkers with the machine and 5 minutes later gives me a quote totaling $789.07. Of that amount the parts component was $482.09. He told me that the computer was bad. I was appalled. This was a 2.5 year old well kept washer. I called Maytag company next day to see if they could at least cover the parts cost. Especially as I have a large family with 3 kids plus elderly family members. After waiting 33 minutes on the phone, the CSR took all the appliance info and tried to see if she could get Maytag to cover the parts cost, given my situation. After about 5 minutes, she told me that Maytag declined my request- quoting that my appliance did not have any warranty and that the notes on the computer regarding my appliance indicated that it was field scrap. Field scrap?? Really? This was an appliance that was bought at Home Depot.This is the lowest of lows that this company (Maytag/Whirpool) can stoop. For a billion dollar company, that are advertising their products as Made in America, they have no heart and no empathy for their customers. They build sub-standard products comprising of cheap parts so that their products only last a few months, then they try to sell you their sub-prime warranty services that are full of holes. And for those poor souls that dont sign up for their warranty services, God help them if their appliance breaks down. They are then left to deal with Maytag/Whirpools appliance service vulture contractors which in tandem with Maytag conspire to squeeze every last cent out of hard working Americans (Especially during these trying times).Just to compare my situation. My parents bought LG washers and dryers in 2008 which remain in full working operation to this day (12 years in operation). The Maytag Bravos broke down in 2.5 years. Use my experience as a lesson. Do yourself a favor and save yourself the headache and heartache. DO NOT, I mean DO NOT purchase or support Maytag/Whirpool appliances. You are better off spending your money with LG or Samsung.

Good deal, recommended by dealer friend. Front loaders, high efficiency, 12 years or so. Finally needs new bearings on the washer. Replaced electronic board 5 years ago. High repair costs would be the worst which is related to low-quality construction. I expect my next pair to last as long as the last 1. Full size, not stackable but oversized drums. Relatively low water usage, lots of different settings for different loads for washing and drying, automatic water level and wrinkle guard.

We ordered a new Bravos washer and dryer at the end of November but due to delivery snafus, we did not have both until the second week of December. Just yesterday, both failed. Part of the drum on the washer ripped off, and the dryer just stopped running an hour later. I am used to getting a long life out of appliances. The old dryer was over 20 years old, and while the old washer was only 17 years old, I thought it would be nice to get a matched set.

I had bought Maytag Dishwasher MDBH979AWW3 in Sep. 2009. Oct 2011, the dishwasher stopped working and the control panel had to be replaced, few days later, it stopped working again and the Thermal fuse had to be replaced. Now two months later, it stopped working again. Till this point, Ive spent a lot of money on the repairs and I wish I had used that money to buy a new dishwasher. Looks like not just the Maytag dishwashers are faulty, but even the parts they have are faulty. I will not recommend any Maytag products to anyone.

In the past 20 years, we purchased a washer, dryer, stove and dishwasher... all Maytag. The washer (purchased 20 years ago) is still functioning well! The other three appliances have all given us trouble and the dryer is no longer with us. Our stainless stove is LOVELY but thats about all its good for. Within 12 months, one of the burners burned out... just beyond its warranty. It has two ovens and 3 years after purchase, neither will hold a constant oven temp and both take an eternity to warm up... although the digital temp on the oven tells me its toasty warm. Recently, the dishwashers control panel wont set properly. An attempt to set it for a normal wash/dry cycle results in rinse only and a 2 hour delay. Make them like you used to, Maytag! Im no longer a customer!!!

We purchased our Maytag® 4.5 cu.ft. White Front-Load Steam Washer online through Menards and picked up the washer on Feb. 5, 2022. We set it up on Feb. 6, 2022 and it didnt work properly from day one. The washer makes a clicking sound when it spins and also gets out of balance very easily. I contacted Maytag and they referred a warranty repairman in our area. He looked at the machine and said it could be one of two things and it would be a major repair. We would have to haul the washer to his shop and he would have to tear apart the washer to fix. He said it would be a big job to fix and we would be out of a washer for a few days.I also had contacted Menards shortly after we purchased the machine and they told us to contact Maytag. They wanted nothing to do with us and didnt want to stand behind a product that they had sold. Getting major warranty work done on a NEW washer makes no sense to me. I am very disappointed in Maytag and will never purchase anything Maytag again. Dont bother wasting your money like we did!

I am replacing my second Maytag Bravos washing machine. My first had heavy use and I rationalized that the 5 year life span was due to the heavy use. The one that I am replacing now is only 3 years old and has only done laundry for one 67 year old woman. It suddenly needed two parts with a repair bill that was going to be over $600.00. I decided it was in my best interest to spend a couple hundred more and replace it. I will not be buy Maytag again. The appliance company that I have bought most of my appliances from recommends Speed Queen which ironically also has a full 10 year warranty on all parts and labor.

We purchased our French Door, bottom freezer in April 2010 after a renovation. We have loved it besides needing more refrigerated space. This past weekend I noticed the appliance was cutting off and a few seconds later coming back on. It has an outside ice and water dispenser as well and the lights will blink on and off of course when the fridge cut off. Called for a repair and when the repairman called in the parts he was told he needed 2 computer boards. One was available however the other was discontinued and they would not allow him to just replace the one board. The fridge cost us $1798.00 from Home Depot. I cant believe how irresponsible Maytag is in this case. I have a kitchen full of MAYTAG appliances and have loved them all. But this is unacceptable. The Maytag fridge I had before was 16 years old. I gave it to a family member when we bought this one and that one just broke down last year so it was 21 years old! Whats up MAYTAG?

Have had continual problems with Maytag Bravos. They will replace in under a 5 year warranty. If not for the warranty, I would be out over 700 dollars spent on this very bad machine. Based on my experience Maytag washers are of poor quality. I would stay away.

After first dishwasher was recalled, this one (installed less than 4 years ago - Oct. 2010) had the electrical panel burn out - two years ago. Now - for second time. LAST TIME BUYING A MAYTAG!

Bought a new home in July of 2016 and the builder had included a Maytag Bravos XL washer and dryer. They are THE WORST performing appliances I have ever used! I will replace as soon as I have the means to do so. DO NOT PURCHASE the Maytag Bravos XL appliances. The engineers that designed them should be fired! The washing machine makes an incredibly loud noise (like an old starter grinding in a 50s car). Im told that this is normal for the machine. Does NOT clean well and leaves soap spots on dark clothes... leaves them on light clothes but I cannot see them. Whites come out dingy even with bleach. The tub is so deep that I have to use tongs to get out smaller items, I am 53 tall and have never had this issue before. Soap dispenser drawer wont stay closed during wash cycle. Clothes are so badly tangled during the wash cycle that it is hard to describe the wrinkled mess that has to go into the dryer.Dryer issues: Very loud. Very wobbly and unstable, and yes, it has been leveled 3 times. Bed linens have to be separated at least 3 times during the drying cycles because they twist and wad up into big, wet knots of cloth. Infuriating!!! Dry time is very long unless you wish to cook your clothes. So disappointed in this product. Total rubbish!!

I purchased Maytag French door stainless fridge 5 years ago for $2200. The doors were out of alignment and I put in new control board; both items almost right away. Then in May 2011, we had to replace another control board for about $400. Then in July 2011, the compressor went out at a cost of $300 for the compressor, $350 for labor. I called to Maytag, Gwen agreed to pay for the compressor but not the labor to put it in. So we now have about $1400 invested in our $2200 refrigerator. Letters to Maytag CEO Mr. Fettig remain unanswered. Do not buy a Maytag appliance!

What junk. Bought this gx2shbxvy05 french door fridge. In less than 16 months the freezer is fine the fridge section gets up to 80f. Throw all the food away. Found the freezer coil covered in ice. Took the back panel off and noticed ice around the copper tubes by the compressor going up into the body. Not good. Put a small brick heater in and slowly melted the ice into the drip tray. Warning, it filled up 4 cups of water and of course spilled and killed the wood floor. After the clean up. Plugged the unit in and it seemed to work for about 3 months. Now its dead again. Looked into parts around 300 to 400 bucks plus labor to replace the system needed parts. P.S. the fridge, this junk replaced is downstairs working after 25 years not one issue other than the color. NEVER BUY A MAYTAG product please. TRAIL APPLIANCE should never have sold this product and should have stepped up to help out. Wont buy from them again.

So far we have replaced the belt. Clothes have never come out clean. High Efficiency... Yeah, we have to put it on extra rinse to rinse all the soap out or wash twice because the clothes just do not get clean. Now it stops right before it drains after the wash. So I had to pull out clothes and use pitchers to get water out before we could tip forward and pull hoses to drain the rest. We checked hoses and connections. All lights work, it did a wash cycle, and again stopped before the drain. Really. All I got was “Didnt you take out the extended warranty?” Well, No I did not. Why would I consider the fact that MAYTAG would need repairs within the first 3 years. Its not like I do a lot of wash. Or have big bulky items. I have a laundry mat close by for that stuff, because it wouldnt get it clean anyway. Never again…

Maytag Centennial eco conserve clothes washer - I purchased a Maytag (non-agitating) washer, (model MVWC400XW) just about a year ago and I cant tell you how dissatisfied I am with this product. It does not clean the simplest of soil from garments. I have actually had clothes come out of the washer after a complete wash cycle, with dry clothes. They recommend putting soap in first, at the bottom of the washer and then load clothes; I have had clothes come out stained as a result the clothes sitting on top of the soap. I am requesting that I be able to return (have this washer picked up) from my home and replaced with a washer with an agitator or a compatible washer that actually washes clothes. I believe that this may qualify as a lemon with regards to California lemon laws.

I have the Maytag Bravos washer and dryer. The machine has broken several times every year, and every year, Maytag makes me feel like it is my fault. They built a machine, and they do not stand behind it. And I cannot get a local machinist to work on it. I have asked Maytag to replace it from the start, and they refused, telling me its out of warranty. The only thing out of warranty is the frame--all parts are new. Here is the history:On 1/04/2008, I purchased it from Home Depot, and it cost $815. Then in 4/2009, there was an F51 code, and Maytag replaced the mother board after long hold times and much pleading to help me. They said they could do nothing, because it was out of warranty. It took manager to manager to manager to get the agreement to extend the warranty. (I then found that this was a regular Maytag issue.)From 9/2010 to 10/2010, an ld code occurred. The approved Maytag scheduled service had to come out 4 different times to attempt to fix the issue. One time, they said it was broken wires for the drain pump. The next, it was off balance; and the next, it was a sensor. Then the next time, they replaced the mother board again, and again after much argument that the part was less than a year old. Each time, they get more and more difficult to deal with and made me feel more and more like I am asking them for something unreasonable. The service guys said the washer was like new.... All new parts and I would never have a problem again. It cost $80 after argument, and Maytag covered the parts.Last 2/2011, problems include a fast spin, ld code, and off balance; and it stopped working. It needed new suspension rods which cost $250. Maytag paid nothing. Then in 8/2011, ld code started again, and I would have to turn off to drain and then restart to spin. Maytag called in a service call, and they never showed up. Every time, they said they read over my file and that theres nothing they can do to help me. And no one else for me to speak to.In 10/2011, the ld code came on permanently. The Maytag call I made this time again said there was nothing they could do to help me.I am so frustrated; I dont know what to do next. I threw away an older set working washer and dryer, thinking I made a great decision to upgrade to this new set. Now my family of 5 cannot wash our clothes. No one will work on the washers locally, and Maytag treats me like Im complaining for nothing and I should just spend endless dollars to fix this machine. And Im at a loss. I had to get a part for the dryer the other day, and the parts store person told me that this washer is one of Maytags mistakes. if that is so, why wont they help me?

We bought MDB7759AWB Maytag dishwasher in 2011. It worked decently until now when it stopped delivering water to the upper rack. The cleaning quality on the lower rack also dropped significantly although it might be due to the lack of water delivery to the upper rack. Apparently there is something wrong with the internal pump. The Maytag service offered a repair for $300+ which I rejected because this is a ridiculous cost and I would rather buy a different dishwasher. My conclusion is that if you buy Maytag dishwasher you need to factor about $300+ for the repair(s) in 5 years as apparently they do when they sell you this product. Anyway, even though Maytag was a decent brand a long time ago (probably in the past century), it is not reliable anymore. It does not mean it has to be much worse than many others but if you are looking for something better than those others I would not recommend Maytag.

Neptune washer and dryer, an all around good buy. Low water use and large capacity for the pair. Bought the pair in May of 2001 and have only had one, very minor, service call. Buying online usually proves to be the easiest and cheapest way to go. Economical delivery costs. Noise and vibration and overall solid construction. Dancing washers can be a real cause for being a deal breaker. Auto shut off for balance is a must. Cleanliness of wash and wear caused by washing and drying. Large capacity and multiple cycle selections for both the washer and the dryer are necessary.

This machine is the worst! I purchased this Maytag washer 2 years ago and the machine leaks from the left side bottom. I called Maytag and they said I need one of the techs out to check the machine and the cost was going to be $115 so I agreed even though was not too happy that there is no guarantee after 2 years. The service tech arrived. He could not move the machine himself and was a little angry so my wife called a neighbor to give the tech a hand after looking at the machine. He called if office to help him diagnose the unit and said the drum seal was bad and it would cost $315.00 so my wife agreed but at the end of the transaction my wife asked the technician, Is it guaranteed that this would fix it? He replied there is no guarantee but we still have to pay to try... What kind of diagnostic is this, Im very unhappy with this company. 1st the machine sucks after 2 years to start leaking and 2nd their service dept. sucks also... stay away from Maytag.

It’s washing day today, so I’m angry, frustrated and livid to do it in my Maytag machines. I’m 72 years old and been doing this for 53 years. It’s not a job you love to do but you do it. I finally get to be able to afford whatever machines I want, so what do I do, buy Maytag. They are beautiful, see through top load, and see through dryer. So finally I get to use them, what a letdown. I don’t understand how they can put these machines on the market. Unbelievable! Also very expensive. The sensor for the water level is way off. It starts washing with hardly no water covering the clothes so this is where I put it on pause and add buckets of water to wet at least the clothing. I did a test to see how the clothes moved inside when washing. It was a load of white towels and I put in a bright green face cloth to see how it moved around in there. Well what a surprise, it stayed on top and moved about 3 inches to the right. That’s all it did. You don’t call that washing, I call that soaking! Terrible washer! I could go on and on but I’m getting too upset. Now for the dryer, the sensors don’t work right so what I do is use the timer and the temperature buttons only. Sometimes clothes gets stuck under the lint basket and by the time the buzzer tells me the load is finished drying, it is so twisted that it’s wrinkled forever. It has ruined a beautiful tablecloth of mine. I can’t sell these machines because I would feel very bad to pass them to someone else…Maytag does but not me. Because of my age I won’t be getting new machines probably, I’m stuck with them, but I would advise anyone shopping for a new washer and dryer, go out there and see what they have, come back home and look for reviews which I did not. Bad mistake! Note: I searched everywhere to write this review to Maytag on their website, none to be found!

After using my GE Profile to death we replaced it with a Maytag; mostly for the cost. Although I hate to admit this, remember the old saying you get what you paid for - Well its true at least in the case of this Maytag oven. I am a constant cook and own a bakery, I often bake many of my products at home. Since getting this oven I have had nothing but failures. The cakes are over done, underdone, cookies burnt, not cooked enough; my time frame for recipes is so off! I wrote a cook book and have baked for years so I know for a fact its not some miraculous mishap that all of a sudden I cant bake. Ive had them come calibrate the oven but still no success.Im going to call them again but I felt compelled to let people know this is the worst oven in history and avoid purchasing it at all cost. I plan on having the service team come out one last time but if this doesnt work I plan on replacing it. Its a Maytag Double Wall Oven-Top Convection-Self Cleaning model no: MEW9630DS-SS. BUYERS BEWARE!

Maytag Bravos XL Washer & Dryer - After a long 45-year use of our old GE W./D. that were still working fine when we decided it was finally time to upgrade. Big mistake. Nothing but dissatisfaction on every level of complaints by those who registered here before us and then some. This all was noticed almost immediately after purchase, but we lived with it trying not to believe our worse fears. That is until we both started breaking out with skin rashes. Just logged on this site after a Google search... We were shocked and disappointed in our purchase decision. We will join in a class action lawsuit if ever one is initiated... Any lawyers with one of these?

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

Just like so many others, our Maytag 300 Quiet Series, just 2 years old, has a malfunctioning control panel. Repairman told us this has been an ongoing problem with Maytag dishwashers. Steam/water gets into the control panel.For a while it worked on and off and now it is dead. I am saving up to do the repair, but in the meantime the dishwasher sits idle.

I also purchased a Maytag dishwasher a few years ago. It has never worked that well. We had a repairman come out once to replace the control board but the problem soon returned. Interestingly, we found that if we wait long enough until the control panel is in the mood, the dishwasher works again and the control panel responds to button pushes, until the problem returns.I dont recall what model I purchased but it seems to be irrelevant. From reading the other customer complaints, its quite obvious that all Maytag dishwashers inherently have problems with their control panels and Maytag intends on doing nothing about it. I guess the extra repair costs that their customers have to pay for their defective products brings in some additional revenue to Maytag, so theres no real motivation for them to fix their ** products.

I bought this machine in 2013 and within a year it had stopped going through any cycle. It turns off and I either have to restart a cycle or set the machine to rinse/spin. My clothes do not seem clean so I have begun handwashing them before putting them in the machine. I retrieve clothes and find some clothes dry. My towels have worn spots and threads pulled out. I cannot wait till I get a new washer because I am going to put this Maytag Bravos in the backyard and take a baseball bat to this hunk of junk.