I, too, am absolutely done with ANYthing Maytag. We purchased our Maytag microwave model MMV4205DS-1 in January of 2016. Within the first year we experienced occasional open/close door issues due to the faulty door latch switches. Now it happens virtually all of the time. The ten year warranty is a joke; it is just a come-on designed to deliver a false sense of security that Maytag will indeed stand behind their worthless products when in fact they wont. I am so disgusted with them.

The washer doesn’t have enough water to to get clothes clean. Even on deep water wash there’s is not enough water. It doesn’t get clothes clean, its very noisy. It takes a long time to was, even on short cycles. You can’t soak dirty clothes, it has a cycle for soak but it is not long enough. After about 3 months the lid licking doesn’t work and the progress lights remain on and never go off. This is the worst washer that I have ever owned. I just want to return it and get a different one!

I purchased my Maytag Bravos from Lowes in early 2014. A few weeks after the motherboard fried and Lowes replaced it with a new one. Within my 1 year warranty the new machine had another fried motherboard. Maytag replaced it for free. Now less than a year later the motherboard is fried again. Needless to say I just purchased another washing machine. Definitely not a Maytag. Now I just have to deal with a dysfunctional piece a junk for a few days until I get my new one. After reading all the complaints on here and other sites, Im very disappointed with Maytag. These machines are obviously lemons and any good company should recall them. Mine will be going straight to the junkyard. I have no interest in having a washer that breaks down every 10 months. Definitely the last thing I will ever purchase from Maytag.

Horrible machine. Uses too little water, cycles are too long. No matter what the size of the load, it takes an hour. Just after 3 years the bearing went out on the machine. Cost for repair will be $250. Thats not even an electronic problem which Im sure would be next. NO THANKS. Im getting a new machine and it wont be a Maytag.

The circuit board on my seven year old Maytag French door refrigerator died. I called a repair company out to see if it could be repaired. He went to order the part and said that it was not available. Now I read a review from someone else saying that Maytag does not have parts for appliances that are over 6 years old. Thats ridiculous that after spending so much money on an appliance that parts are not available. I will never buy another Maytag appliance.

Bought a Maytag Washer & Dryer and after only 4 years the front panel went...cost to replace part only $653.55. After expressing concern about the price Maytag cut the cost of the part in half - now installed $475.00. Disposable dryer. Choked on it and decided to go ahead with the repair. Part was to be in in a week and it is now been a month. Maytag/Parts supplier no idea where the part is and doesnt return phone calls. Have to use the laundromat (family of 5). More money out of pocket. Not to mention time. Called Maytag again to complain about the service and having to pay more money out of pocket to use the laundromat. They basically told me, Too bad. Have used Maytag appliances over the years and always been satisfied but the company is clearly going downhill.

Purchase washer and dryer January 26th, had delivered said February 2nd. Had a horrible delivery service, delivery men were very rude and scratched the dryer. Washer never worked correctly, called and had exchange set up for February 9. Washer was delivered on February 9 and again we had a horrible experience with the delivery drivers. They scratched the washer. The owner of the delivery company came to our home making sure everything was correct. Washer worked well for two and a half weeks. Then I noticed the water was slowing down when it was filling. Then this morning the washer completely stopped filling. We called Maytag and they told us we could not get anybody here until next Saturday. They were rude on the phone. We then called Home Depot where we purchased it and said we want to return the washer and dryer. They said we cannot return it. We are stuck with it. Now weve been arguing with Home Depot and Maytag all morning trying to get someone to my home to get the washer fixed. This set cost $1,400 and Maytag is not supporting us on selling us 2 lemon washing machines. We are stuck because we cant return them or exchange them. Home Depot gave us an option to exchange for a lesser model that they have in stock. When you read the reviews for that model the reviews are terrible. I would highly recommend that you do not purchase a Maytag or Whirlpool product. Their company does not stand behind their products or their workmanship. If I had the opportunity I would return these to the store. But it has been over 30 days and I believe that is not an option. Stuck with a lemon. Very sad that customer service is so crappy on an American-made product.

It went bad, then I called a technician who replaced the compressor. After a few months, it broke down again after I had bought new parts for it. I was very dissatisfied with how the refrigerator was built. I spent lots of money on it, and it wasnt worth it.

I purchased Maytag Centennial Commercial washer and dryer eleven years ago. Both are still going strong. It has been a great purchase. Only issue is a couple of stains have appeared on outside of appliances.

We paid over 2000.00 for our refrigerator in May 2011 and within a year ice started forming on the bottom and then leaking out on to the floor. Every week I have to get out large beach towel to lay under the pull out drawer, break up the built up ice and then pull it out onto the towel. I too called Maytag who said it was out of warranty. Now today I notice a significant temperature drop in the refrigerator and freezer. Whats odd is that the day before yesterday the freezer was so cold the ice cream was solid as a rock. I have not changed the factory settings since it was installed. I HATE MAYTAG!!!

My new Maytag washing machine does NOT CLEAN clothes or anything else. Waste of money. I have soft water, use bleach, hot water, Tide. I have even tried adding some baking soda. No use. I cannot wait until I can find a washing machine that works.

Bravos XL was costly. Mistake! I owned my first Maytag for 20 plus years. The sticker shock of buying a new Maytag 4 years ago was pushed aside knowing how long my previous model lasted. The salesperson at Lowes closed the deal with his explanation of an improved gear driven system vs the old belt and pulley version. Oh how wrong! I too have the jet plane from hell landing in my home for over 2 years now everytime the spin cycle engages. This is a two person family and it failed at 2 years?!?!?As for water conservation... if I dont include the additional rinse cycle, my clothes dont get clean. Watched the YouTube on how to repair this unit... but what guarantee do I have that it wont go back to the same problem in another year? Cant afford another big investment like this now that I am retired, so I will run this baby until it seizes up. Dont wash clothes if company is coming or if you want to enjoy evening TV programs. Not sure why this unit hasnt been recalled based on all the complaints I have read on this site?? Worst decision I ever made! I bet the Maytag Repairman is spinning in his grave!

After only 3 yrs of normal 2 person family use my Maytag washing machine completely failed. The ball bearings in the transmission seized requiring the replacement of the transmission. At the same time the control panel failed yielding the machine completely unusable. The repair cost was more than originally payed for the machine, forcing me to purchase a new one (not a Maytag). Maytag said since there was no recall on this model that they could not help me. I bought the Maytag because of their claim of quality. This was not my experience either with the product, or the customer service.

This washer is the worst! Dont buy it! I paid a huge amount of money only to have it break down in 3 years! My husband and I live without children so our use is minimal. The spin cycle started to make a noise sounding like an airplane taking off. The repairman said it could be fixed for $800 and his service call, he told me that there were over 2400 complaints with this washer for the same product. He also told me not to use it while Im out to avoid the risk of flooding my home! Save your money and DONT BUY MAYTAG products.

I purchased a Maytag electric dryer Bravo 300 Series in November 2009. December 2011, the main computer board went out and had to be replaced. Do not purchase Maytag appliances. They do not stand by their defective products. First and last Maytag purchase.

We purchased a $500.00 Maytag dishwasher, Model #MDB7749SBW, in August 2013. In December 2014, a little over a year of owning it, the pump failed. We called Maytag and they had a service company come out and replace it. We paid $181.00 for this service call. In July 2015, the control panel failed so we called Maytag to see if they would replace it at their cost. All they are willing to do is to send another service guy out at our expense. The service call is $89.95 and that doesnt include the labor! The total with tax will be close to $200.00 again!!! Now we are getting close to spending $1,000 for this piece of junk! In addition, this dishwasher is only used three times a week because there are only two people living in our household. It is obvious after reading the other complaints that the control panels are defective and I am sure that Maytag is well aware of this issue. So, buyer beware. Dont even consider purchasing a Maytag dishwasher unless you enjoy watching your money flush down the toilet. They dont even deserve a 1 star rating!!!

I bought a new washer and dryer from Clarks Appliance on North Monroe St.,Tallahassee, FL. I do not like the washer. It is a top loader and has a lock on the lid. The pause button is supposed to let you open and then is supposed to continue the wash. But it releases all the water and shuts down. I asked to return the washer because I have had it only three weeks. They wont take it back. So now I would like to trade or sell it.

I bought a (Maytag brand) Whirlpool washer but it didnt clean clothes, so I had a repairman out. He ran it through their test and agreed that my clothes had lint, pet hair, and dirt on them, and said that was as good as it was going to get. No one called back from Whirlpool. I called them and a second repairman came out, but it was the same story. I got the same repairman back out again after several calls to Whirlpool and listened while he called in and answered questions from Whirlpool - Is she using HE laundry soap, etc. - the same things they asked me. I bought the machine because it was supposed to have one of the largest capacities available. I stood there while the repairman told them that the clothes hanging to dry were covered in lint, dirty, and extremely wrinkled because they twist into a big knot in the machine, among others. No one called back again, so I called them. The service representative told me that I was loading the machine wrong, I was not using the right soap, and that the report they got from the repairman stated that the machine was working as intended. I told them that I was standing there as the repairman told them that my laundry was not clean. They told me that it was not what their record stated. I thought washing machines were supposed to get laundry clean and get the smell of body odor out. They suggested that I use the bulky setting, so I asked them if I should have to use the bulky setting for a load of underwear. They said that the machine was working as intended, but I wanted to have someone else come back out. The appointment was scheduled, but then the repair company called me and asked if I was aware that I would have to pay for the service call. I explained that there must be some kind of mistake because it was a new machine. She told me that Whirlpool had been doing this for a while and they werent sending out repair techs anymore without notifying the customer, and that Whirlpool has been doing it as standard practice for some time now. I requested a written statement from Whirlpool about the incidents but I was refused.

Purchased new about 3 years ago, doesnt clean, ties clothes in knots, leaves white spots from softener that doesnt get wet sometimes after cycle, some areas are still dry after untying. Now error code 51 keeps appearing, service man 4 times replaced rps sensor as directed, nothing changes. Need a chain to drag behind truck, no technical support from Maytag or whirlpool. Old ones of 20 years still worked good, gave to niece. Lucky her.

Our Maytag microwave, which we bought based on Maytags supposed quality, is nothing but a piece of junk. In two years it has had or needs repairs that nearly double the original cost! Thats ridiculous. We are done with Maytag and are not going to get suckered into their Whirlpool/KitchenAid or other brands. So long.

I bought this Maytag dishwasher model mdb6709awq1 from Home Depot that installed it; they did a good job installing for a fair price. My gripe is with Maytag. I have owned a Maytag dishwasher since 1977. Back then it was the best you could buy. Since Maytag sold out to Whirlpool to save being bought by the Chinese, the design of the dishwasher has lost or gave up their unique design that made it so good and dependable. The inside of the rack/drawers has been totally changed. It used to have fold down racks on each side of bottom rack that was great for coffee mugs, small bowls/containers, and they came out sparkling clean. The utensil basket was centered front and again the utensils came out super clean. Maytag sold their soul when they sold out to Whirlpool. Dont know if that was part of the deal that they give up their unique design or why did they change the rack design. I wish I still had my old Maytag from 1998 that yes, worked without a problem, then I sold the house with the dishwasher. Why is it that so many appliance makers have taken dependable workhorse designs and phased them out? What is wrong with an appliance lasting for years, decades without problems? Only thing I can think of is that they wont make millions every year as they only would sell so many a year if they are dependable as they wont need to be replaced.

I have a 4 year old Maytag refrigerator, model F2557HE, with French doors above and freezer below. The compressor is dying, which amounts to total failure of the fridge. Periodically the compressor tries to start, there is a whirring sound that lasts and lasts and repeats as the food defrosts. Then mysteriously hours or days later it starts to run again and the melted ice cube bin turns into an iceberg. The appliance repair company tried replacing the starter to no avail, and now tells me it is the compressor itself. Each time it stops, I transfer my food to the 30 year old Whirlpool in the garage which still works fine.

The first problem happened a month after we bought the horrible product. I had biscuits baking in the oven and the oven door locked itself like when in self-clean mode. Maytag sent out a repairman that had the part in his truck because they knew there was a problem with that models door. I pointed out that the door does not shut properly, causing inaccurate heating and scorching on the outside of the oven door. The repairman insisted that it was shut properly, and that it was designed at the angle the door sits. He replaced the scorched part of the door, but it immediately scorched again. I have had the part replaced 3 times, and will not do so again until we sell the house. I have spent over money over and over again to make the repair, because it makes the stove look like it is filthy with grease. Now, all the dots painted on the glass top are coming off, and the remaining black glass behind it also looks like burnt grease. It is so embarrassing when entertaining; but the stove is clean. I spent a lot of money for this, and it has been junk from day one. Avoid purchasing.

The Maytag range was purchased locally in 2012. The racks kept falling as the oven cavity warped in a convex making the rack supports too wide. The racks fell at the best position to cook a turkey. This could be dangerous when lifting something like a turkey or pie with filling! I was told that the oven cavity is NOT replaceable and I needed to purchase a new range! $1,600.00 plus taxes were spent just three years ago and now Im being told it cannot be repaired, no parts are available and needs to be replaced! Im sorry but I feel cheated and hurt because Maytag will not give any concession despite my pleading. What a dirty way to conduct business! No concession except an offer to cancel the service charges so far if I replaced it with another Maytag range from Delhi Radio Ltd. Are you serious?Why cant wider racks be provided for in these cases? Just what kind of engineer would compromise the thickness of a ranges oven cavity? Then build the range in such manner that the defective part is not available and cannot be replaced? Its a sad day for Maytag! Shame on you! Ive seen Maytag washers built in Newton last 35 years of hard family type washes! Whirlpool has purchased the name, stamped their own products with the Maytag name, and rested on the fine reputation of the name brand. Everything else is different! The Newton plant is in mothballs leaving hundreds of proud faithful employees stranded. Its a sad day for me and many others who were duped by a brand name and got something completely different.

In 2011, I purchased 2 Maytag dishwashers, one for my tenant and one for myself. In 2014, the circuit board on my tenants dishwasher failed, when the unit was only 3 years old and of course out of warranty. I first contacted a local repair person, and he informed me that the repair plus service would be close to $300. When I contacted the company, after about an hour on the phone, they agreed to send their authorized repair service person and after his evaluation, would repair the unit with no charge to me, as a courtesy. This whole process took about 2-3 weeks. I felt that was fair. It is now 2015, and my unit, which I purchased at the same time and the same type, now is not working due to a faulty circuit board. My tenant uses her dishwasher more frequently, and that is most likely why her circuit board went first. This is a design flaw, or perhaps planned obsolescence. At any rate, Im not happy with this, and my model is mdb7809awb2, and serial # is FO4205659. Do you know if there have been any other complaints on this? Thank you for your help.Updated on 07/30/2015: After I wrote my review, I contacted Maytag about the problem. After considerable wait times, I spoke to someone who set up a diagnostic repair call, giving me the impression that Maytag would cover it. When the repair company called, they told me that I would be charged $104.95 just for diagnostics. Labor and parts would be additional. I called Maytag again, and they agreed to let the repair company charge back the diagnostic fee. After diagnosing the problem, it was determined the problem was the control panel and not the circuit board. The cost to repair with tax came to $315.85 and it was only this low because the repair company waived the return service trip. I can get a new dishwasher for a little over $400.00. I am very disappointed in Maytag, because I remember the commercials where the Maytag repair man was bored because the products were so dependable they never broke. My unit is only 4 years old, and its sad that it costs so much to repair it.

I purchased a Maytag washer the centennial commercial technology model about 4 years ago. At the just barely 2-year mark it needed an all new transmission (Approx $800) Thank God for extended warranties. Now it is doing the same thing again making terrible noise. For a purchase of $1000 this is not good quality or decent workmanship And Maytag does not stand behind their product. I guess I need to buy another brand from now on. Please beware of very costly repairs with this one.

I purchased Maytag Bravos MVWX500XWO top loading high efficiency low water washer and it is a piece of junk. All my clothes came out horribly wrinkled and ruined a white jacket when I used the color safe bleach dispenser. I purchased the machine from Sears, where I purchased the extended warranty. I had an A&E technician out and he explained that the new technology of machines are expecting all clothes to be dried in the dryer. Okay, but what do you do with clothes that say hang dry and they come out so wrinkled and twisted that even an iron cant get the wrinkles out? Another suggestion from the technician, put the hang-dry articles in the fluff cycle of the dryer. Well, thats a big nugatory since they are supposed to hang dry them. Supposedly, this machine is all about energy efficiency but isnt it a contradiction when you are using more energy with running a dryer? Someone suggested to me that perhaps there wasnt enough water being dispensed during the spin cycle resulting in horribly wrinkled clothes. Either way, I am on my last nerve with this machine. I always thought that Maytag was an elite company. Well, how wrong I was! Their customer service is pretty much not customer-oriented. Its all about the almighty dollar. After speaking to a supervisor, she explained to me that I should contact Sears with my complaint that Maytag had no recourse. Well honey, Sears did not make the atrocious machine. They are just the so-called messengers. I have unfortunately found that once Maytag sells their horrendous product, they dont even stand by it. Now isnt that typical of companies nowadays and sadly, lacking with this company? Pride in their workmanship! And again, its all about the almighty dollar and who gives a ** about customer satisfaction? Maybe thats why they dont have the Maytag repairman. He was ashamed to be associated with this irreverent company.

Our circuit board has went out twice. The stove is not designed well. The oven vent sends hot air over the plastic panel / circuit board. It melts... The first one was under warranty and the second, only three years later, was not. This is a very expensive part and Maytag will not even talk about giving me a discount.

After only three years of gentle use, my Maytag front loading washer bearing went. The repairman said this was because of too much detergent and the repair bill would be over $1100.00 (more than the cost of a new machine). I would never buy this machine again.

This washing machine is garbage! We paid almost 1000$ for it and it damaged most of our clothes. We believe this washer was released from Maytag with a functional problem. Because it does not drain the water and soap properly, therefore it leaves white stains on the clothes after it is done. Please see in the picture. After recommendation from Lowes we clean washed with Affresh for many times, it did not fix the issue! We called Maytag customer warranty service. They sent a technician and his solution did not solve our problem. We called them again and they said if they send a technician again they might charge us 130$. We think Maytag warranty is a waste of time and energy. They are useless. We will never ever buy anything from Maytag.

I am absolutely disgusted with this Maytag Bravos XL washer. Have owned it 6 months and cant wait to get rid of it. We live on a farm and have cattle. If jeans go in the machine with mud on them, they will come out with mud on them. I have tried soak, deep water wash, power wash. Nothing works. I might as well put a wash tub in my back yard and wash by hand. Anything black must be washed by itself as it will come out covered in lint. How did this machine ever go on the market? Expensive mistake. Please do not buy this machine.

Buy this washer! It has the best features! No matter what the setting, your clothes will come out as dirty as you put them in, only with even more odor! I just cannot believe how many different settings they managed to program into this washer, each one delivering the same miserable results. I am so happy that I spent so much money on a washing machine, that in some cases, doesnt even get my clothes wet. Truly amazing technology!

I bought a model MDB7749AWW1 Maytag dishwasher in May 2011. I thought I was getting a nice one, but no one really liked the way the racks were designed after we got it installed and began using it. My biggest complaint however is with the control panel. It failed in November 2011 and was replaced under warranty. It has now failed a second time in June 2012 (just over one year old and out of warranty). Theyve offered to pay for the parts since it is so close to one year and I pay labor. Well see how that goes. Looks like there are lots of problems with Maytag control panels.

So far, so very good. This is the first time owning/using an electric oven. I just love my Maytag. It was affordable, especially since it was a combo sale with the over-head matching microwave from Home Depot. Two years later and it's as if I just purchased it. Wonderful, wonderful, wonderful.

I will never buy anything made by Maytag again. I just bought this washer 9 months ago and the sensor broke. The repairman said I have to pay $300 for the new part and it will take 3 weeks, then the repair told me many people have this same issue and he wanted to be honest that this always happens to these washers and my best bet is to buy new... I am so sad I saved for 4 months to buy a new washer and it was a bad decision. I have learned my lesson.

Rather than go through all the things I dont like about this washer, just read all the complaints because that is my complaints also: bearings, not enough water in tub, clothes not getting cleaned. Just check out the lint filter and see the gray and dirty lint after a load and you will see it doesnt clean the clothes. Now, the motherboard is kaput! Cycles are all screwed up. Cost is $386 for motherboard plus labor and I will not put one more cent in this piece of crap.Listening to the salesman and consumer reports on the best washer to buy. All they are concerned with is energy savings and believe me when I say that all energy savings products are a joke because you give up operating ability for the sake of energy savings-- true of refrigerators and washers, dryers, furnaces and the like. I will be buying an agitator washing machine. The saving on water are not enough to give up clean clothes.

Oven racks falling down and theres appears to be no solution because the interior liner of the oven has warped. The 3rd party repair guys tell me the interior liner needs to be replaced, its not worth the repair cost, Im better off shopping for a new set. Its so unfortunately that this happened (we moved into this house with existing appliances that we cannot use...) and it seems to be a common problem, yet Maytag claims they have NOT received any complaints about this.

Excellent dishwasher but door kinda flimsy. Front panel scratches too easy. Top rack needs to be stronger and a bigger bottom rack. Other than that running wise dishwasher is excellent. Its hard to beat Maytag. I think they just build cheap stuff around good motors.

I purchased a new electric oven/stove, dishwasher and over the stove microwave. My dishwasher didn’t work from installation and it took Maytag over a month and half to repair. My oven door hasn’t worked properly since purchased and finally broke and I have been without an oven for two weeks waiting on repair. The customer service does not listen to you and seem to be completely unconcerned about your problem. I was told the item broken was a common stocked item and the repair would be quick but that was not true. The repairman told me they would have my parts in a week and would install them on a Monday. They have now scheduled my repair for Thursday. Over two weeks with no working oven. I will never purchase a Maytag appliance of any kind due to the terrible customer service.

Maytag front loader 5000 series error codes - After using my washing machine for 3.5 years, under light duty, I have an error code of SUD and F35 indicating that the pressure switch has failed and needs replacement. I will need to buy a new pressure switch out of pocket and replace.

This is undoubtedly the worst washer I have ever owned or used! I have never before felt compelled to write a review on a product, but I wanted to make other buyers aware. There is not enough water to clean the clothes - the water level doesnt even cover the top of the clothes, so the top of the clothes are dry as they are agitating! After drying (dryer doesnt dry either) the clothes do not smell fresh or clean. Ive put up with it for 3 years and am disgusted every time I use it. Im just about ready to buy another set.

This washing machine is TERRIBLE! If I could give it zero stars I would. It broke right after the first year and has been nothing but trouble since. Agitators has been replaced twice. Clothes do not get clean. Do not buy this machine. When I contacted Maytag with my initial complaints they were not helpful. Please save yourself the trouble and buy a different brand machine.

Model MDB7749SBM1, Complete FALSE ADVERTISEMENT and GARBAGE. Let me explain. Maytag clearly claims this dishwasher is stainless steel on the inside and out... FALSE, BOGUS CLAIM. Please check for yourself, tried a magnet to it everywhere and the magnet stuck everywhere. I have had this dishwasher for 15 months. The keypad frequently stuck. When I called Maytag, they told me if its usable, there is no defect. 15 months after purchase and 3 months after WARRANTY ran OUT on Thanksgiving Day with 25 guest. The keypad finally quit for good. I called the Friday afterward and was told no service for a week. I called and received local service but they told me it would need a keypad, which I waited to call on Monday since Maytag is closed on weekends how ironic. I was told they wont cover anything since a certified person didnt come out even though nothing was ever fixed and they blatantly lied to the consumer. Tried to sell me an extended service plan. I will NEVER BUY ANOTHER MAYTAG PRODUCT AS LONG AS I LIVE AND WHEN IM IN LOWES OR HOME DEPOT, I WILL TELL EVERYONE IN THERE SHOPPING THE SAME THING, DONT BUY MAYTAG IF YOU KNOW WHATS GOOD FOR YOU.

Ive owned the stainless steel version of the Maytag dishwasher model MDB7749SBM purchased on Sept 6th 2013. July of 2014, my first control panel went out. Lights not responding. Was within the 1 year warranty period. Now, that panel is acting up again. I called Platinum Factory service and they wanted to charge me for a new panel and the labor. Well, I used a few choice words on how I felt and the customer service person said the part would be free. Well, nothings free as I scheduled a visit by the Platinum Factory Service. They of course call 5 times to make sure you are home. The day of the service, the tech calls me to see if Im home. I of course said I am... then, he goes to tell me the labor charge for him to come out and hourly rate will come to $189!!! I said screw it and dont bother. Maytags quality and engineering SUCK. Avoid them...

I purchased a Maytag dishwasher because they are supposed to be known to be a good brand. But my dishwasher is 3 years old and it started rusting around a steam vent on the outside of the door! This issue has been ongoing but as Ive been busy, I havent had the time to address the problem with Maytag since its out of warranty anyway. But I feel like this should not be a warranty issue to begin with, it should be a recall issue. I had a plumber look at this, and he said that it was caused because the vent was not properly sealed during manufacturing. Now it looks as though mold spores are growing inside the steam vent! Maytag will not stand behind their product, so why should I invest anymore money into it?! I would rather purchase another dishwasher (OTHER THAN THIS BRAND) than dump another penny into this garbage dishwasher!

Purchased Maytag MDBH979AWW serial #FY4202009 from Lowes October 30, 2009. Control panel went out after warranty, and we replaced it. It quit working again in May 2012, and we replace the control panel, and then in November 2013 it quit and we replaced the control panel along with a new door latch just to be sure on December 4, 2013. The dishwasher quit working mid-cycle a couple of weeks ago only 9.5 months since we replaced the last control panel. Im fairly certain it is the control panel again. We have paid more to replace control panels for this dishwasher than we paid for the original appliance. There should be a recall and compensation on this issue. Very disappointed that Maytag and Whirlpool do not resolve this issue. We will be buying a different dishwasher, and it will not be Maytag or Whirlpool.

I am grateful I dont have to beat my clothes on a rock. Absolutely the worst dryer Ive ever had!!! Previous Kenmore washer was my favorite! This Maytag does not allow me options to stop, soak & freely open & close as I choose. Even my adult children who occasionally use it say its the worst!

1998 MAH4000 - I got this unit (used) in 2004 for $400, and it has pretty much kinda been a lemon ever since. I have babied it through until now, though it had the wax motor repaired twice (Im glad I bought an extended warranty from Maytag, but that added $400). Now the motor control has gone out. I like the concept of the front-loader, but my folks Maytags (and my grandparents) have run for 30+ years without any of the hassles Ive had.Granted, I like bleach, so the mold thing has been less of an issue for me, but wow. I have to say I wont ever purchase another Maytag appliance again. Im about to drop the $185 for a new motor (the motor control board went out, and apparently I need to get the new motor and control). Im pretty sure I lost a phase based on the burnt components on the board. Im glad I know a bit about electronics, or else Id really have been in for some money. Boo on this model!!

Bought it in 2013. Just replaced freezer motor. I thought for sure it would give me better service.

All of a sudden, the lid lock light is flashing. The washer is only 1.5 years old!

I purchased a Maytag Centennial Commercial Technology washer in September 2010 which is less than two years ago. It decides to stop spinning correctly in the Spin cycles. Clothes come out sopping wet so I contacted Maytag to have a tech come out. On the day that the tech came out from A&E Factory Service, he stated it was a switch. He changed the switch and still, it did not spin correctly. He then proceeds to state that it is another part, which again, it did not do the function correctly. He then proceeded to state that it is the clutch, then the transmission. The cost was raising to $519.00.I stated that I did not want to proceed because I would be purchasing a new washer with that quote. I stated to place all the original parts back onto the washer. He did so, but did not place them on correctly. The casing of the washer no longer is secured to the drum - bolts and plastic pieces are still on the side. He left my house with finger prints of grease on the walls. If this is the workmanship that Maytag recommends, then my business deserves to go elsewhere.A complaint was filed with the A&E Factory Service. However, no one has contacted me about the complaint as was requested. All I want is for my washer to be fixed or to have a tech who is knowledgeable to come out and fix it. I contacted Maytag to inform then of the situation and they stated that all their techs are certified. I do not believe that my washer of less than two years old could possibly have so many parts that are faulty. I hope that this may, in turn, help another consumer to avoid purchasing washers through Maytag and their parent company, Whirlpool.

I purchased this washer January 2020. Bravos XL model# MVWB830DW5 is the worst washing machine ever. Does not clean your clothes, leaves soap residue on your clothes. Clothes aren’t fully submerged in water for the wash or rinse cycles. Do not waste your money. You will be highly disappointed.

I am sorry I purchased this machine. It was meant to replace a 17-year-old Maytag dishwasher that was not repairable. I figured they were good machines. Wrong. Perhaps I have a lemon, I do not know. I bought the machine on the 23rd of November and it was installed on the 29th of November. Here it is December 12th and I am sick to my stomach. I have already had to contact Maytag customer support and have a repairman coming. This machine does not clean worth a damn! My glasses look worse coming out of the machine than when they went in. I have run two loads with the machine so far. The auto-sense cycle is a joke. It took over four hours to complete and things did not come out clean. Last night I tried the normal cycle. It came up with a run time of 2:36. The first rinse was cold water. The detergent cup was open and empty at 20 minutes in. So what does the machine do for the next two hours??? When the cycle was finished I looked at the glasses and they were spotted and streaked with remnants of fingerprints and lips. So I ran it again trying the quick cycle. Not one bit of difference, still nasty looking glasses. If this machine cannot get the upper rack clean, how can I be sure the lower rack is getting sufficient cleaning? One would think that for $600 it could at least do the job it was meant to do.

Bought this because it’s American made. It seems to be very glitchy. If you don’t use the detergent drawer it always flashes low detergent. The quick wash leaves soap on clothes. It acts up and leaves clothes too wet. No buzzer to tell you when it’s done. Have to hold button for 3 seconds to start. You can’t just hit button and walk away. Then wait for it to sense the load first to make sure it starts. Very expensive model.

I absolutely love this Maytag Bravos XL washing machine... I bought this machine before doing any research because of a sale and then after reading multitudes of reviews... positive and negative... I thought I had made a mistake. The absolutely most important thing with this machine is to load it properly and select the proper wash cycles. You must stack your clothes around the outside of the drum leaving the center open. You must use HE detergent. This is a Commercial grade washer and is meant to be loaded. The twisting and wringing of clothes is because of the high speed nature of the spin cycle (commercial). If you have never been to a public laundromat then you should try it and see what those machines do to your clothes. I too was apprehensive about the water levels at first... So I stood there for an entire cycle multiple time and on diff settings.The machine is constantly adding water as needed and each time after about 10 min... no matter the size load I put in. The clothes eventually were covered by water. Have had no issues with clothes that come out dry in spots. I suspect this is due to improper loading. Again my info on using this machine... loading techniques etc.. all came from positive reviewers stressing the importance of these key factors. This machine was not designed or intended for light or delicate use. So if you do a lot of those type loads perhaps this machine is not for you. As for the loudness and banging I have read about I have not experienced that. I have read reviews that the problem in some case ended up being metal or plastic drip pans used under the machine. Mine sits on concrete. Anyway hope this helps someone out.

We bought a Maytag Neptune Washer and dryer package from Home Depot in 2004 and had nothing but problems ever since. Such things as washer had mold constantly. Also, clothes seemed to have a foul odor after washing. The dryer always seemed to have to be ran twice to get clothes dry.

The washer is designed to use low amounts of water. The top is glass so you can watch what is or is not happening. The manual states there should be clothes above the water after filling. However after the wash cycle with a full or even half full washer, there is still some dry clothes above the water. As a result the clothes are not washed until the rinse cycle. I called Maytag and a repair tech came out to fix it. His solution was to trick the sensors by dumping a pail of water on top of the dry clothes before starting the washer. The sensors think there are more clothes than there really is. Will never buy another Maytag or Whirlpool product again.

Series 200 dishwasher wont start. Just over 1 year old. Control panel needs replacing which I found out, is a constant problem and a design flaw. Called Maytag and they would only offer 25% off new part. Why would I do that when it is just going to go bad again?

We purchased our washer and dryer set in December of 2010 and had it for about 2 years with the extended warranty...needless to say around 1 1/2 - 2 years the metal around our bleach dispenser started rusting. Maytag considers this cosmetic! I am shocked to think that its cosmetic...on the outside of the washer yes, but on the inside no! It is faulty on Maytags part. I have spoken with Maytag and they tell me if it doesnt happen within the first 30 days there is nothing they can do. So I will tell anyone and everyone what was said to me via Maytags own repairman, Buy cheaper washers as NO ONE offers an extended warranty on the inside of the washer rusting. Whirlpool is the owner of Maytag now so beware of Whirlpool as well. Check out the warranties and make sure you will be covered longer than 30 days for rusting on any washer you intend on purchasing. We learned the hard way and well....we will be buying a cheap washer like the repairman suggested when this one goes out.

I have a Maytag Washer and Dryer that I am very happy with. I have had both of them for about 6 years. I had a problem with the soap dispenser not working properly shortly after I purchased them, but a service technician came and fixed that within a few day. I will probably stick with the same brand when/if I do have to replace them.

I totally understand the technology age. We need to move forward as a country and keep up with modern technology. But somebody please tell me why this means companies have the right to not stand by their products? Why do consumers have to pay the price for bad products and companies leaving us high & dry? My husband & I were excited to redo our kitchen. We bought all new appliances in November 2011 - all Maytag. In December 2012 (13 months after we bought them), we started having issues with the oven. The oven would not maintain the proper temperature. We called a service man in January 2013. He deduced it was the computer board so he replaced it. Cost to us - $350 (including service call and labor). Now, less than 2 months later, the same problem. Maytag, Whirlpool, Kenmore - whatever company you are now - rest assured, you will not survive if you continue to produce shoddy products and refuse to back them up. The service man is to stop by again tomorrow. I refuse to keep plugging money into a product only 15 months old. I will not buy another product from you again. I just hope the dishwasher, microwave and fridge make it to at least 5 years old. Isnt this funny? My grandma has a Maytag washer & dryer - 35 years old. You sure cant say positive things about your products today. Good luck to your future - youll need it.

We ordered a new Bravos washer and dryer at the end of November but due to delivery snafus, we did not have both until the second week of December. Just yesterday, both failed. Part of the drum on the washer ripped off, and the dryer just stopped running an hour later. I am used to getting a long life out of appliances. The old dryer was over 20 years old, and while the old washer was only 17 years old, I thought it would be nice to get a matched set.

We purchased this Maytag top load washer less than three years ago. Spin cycle stopped working and repair for new actuator motor is $240 (machine cost $500). I should have read Maytag’s reviews before we bought it (averaging about 2/5). Living on name - don’t buy one.

I bought a Maytag dishwasher (Model: MDBH949AWS2) from Home Depot on 07 April 11 and it died 24 August 11. I called Maytag to set up an appointment for repair. The repair person showed up and stated that the control panel needed to be replaced. Apparently, if moisture gets into the panel it shorts it out. One would think that when designing an appliance that utilizes water and creates steam, it would be sealed. Anyway, the repairman explained that because the dishwasher was in a residential program, the warranty was null and void. I wish that someone would have explained this before I purchased it. I went online to AppliancePartsPro.com and ordered the part for $100.75 including the shipping cost. Then, I went back online to look up how to install the panel. The repair person said that they are charging $133.00 for the part and $129.00 to install. A small star tip screwdriver and 15 minutes was all it took to fix. From what I have read, this will not be the last control panel but, at least, I know how to fix it. Another thing that I know is that Maytag is off my list of future appliance purchases regardless of where Im using them.

My freezer has been leaking from the bottom for a few months and now the icemaker has quit working as well. The refrigerator has been purchased less than two years ago. The warranty is expired. I will not fix this refrigerator, as it is a gigantic piece of junk. However I would like to be compensated by Maytag at least 1/3 of the price so I can have it removed from my house before it creates more damage to my floors and subfloors.

Maytag dishwasher from Home Depot, model MDB7749SBM1. Bought it last May from Home Depot - in a little more than one year it has already needed 2 repairs to the control panel. We are having a lot of problems finding someone to come and repair it. We want our money back. This is a piece of junk!

I purchased this washer three years ago. It worked fine, but all of a sudden the washer stopped spinning and was not following any of the cycles. Of course it was out of warranty. The repairman states the computer board on the washer is fried and will cost $400 to replace. Several stores have stopped selling Maytag because of quality issues. No more Maytag for me.

Dishwasher MDB7749SBM - Have the same problem as everyone else, panel board (2nd one, 1st was under warranty). This panel W10475787 is 2 years old. Keeps lighting up doing what it wants to do. Dishwasher is 3 years old. Cant find out if there is a recall on this part (there should be).

I bought my Maytag Bravos top load washer from Home Depot. In one year. I had the Maytag warranty people out three or four times. The warranty ran out and I purchased an extended warranty from A&E. I have had them out at least five times.I called Maytag and they told me since that I didn’t get the extended warranty from them, that there was nothing they could do for me. I explained to them that this washer cost me over $900 and that I have had numerous repairs on the washer, in which the warranties cost me over $400 so far.How much do I have to keep paying for this lemon? Maytag will not do anything about it! This goes to show you that paying top dollar for a washer does not guarantee you will have a good product. In this economy we can’t afford for this to happen. This is a very bad product and Maytag will not stand behind their own products, but they are willing to charge the consumer high dollar for them. This is a disgrace!

The Maytag MGR5875QDW oven does not come up to temperature. It might start, but then it will give 2 dings and show a failure. I have called the 800 number in the manual. There’s no good help. I turned the power off and then on. It’s no help. This a pain in the rear end. That is a kind way of saying it. Home phone is **; cell phone number is **. Call me any time. Thank you. You do not want my wife to go on the internet!

This so called high efficiency washing machine, and others like it are absolutely awful. They do not properly clean clothes. I frequently have to put loads of clothes through two or even three times in order to get things cleaned properly which our old washer did easily in one wash. That is the exact opposite of efficient. It is so bad that it actually borders on being a genuine scam. Do not buy! Huge waste of money.

I own a 2004 Neptune front end washer that Ive dealt with the terrible smell of stagnant water since I got it. Now the motor went and I was told I need a new washer even though the product warranty information clearly states the motor is covered for up to 10 years. The repairman told us that the motor thats in my machine is no longer being manufactured. How is that my fault? I do not have another $800.00 for a new one, which is now not even a lot of money for a washer. Ive already bought 2 washers since I built my home 14 years ago. Its just not right!

After 6 months of use, I still HATE my Maytag washer. I will never buy Maytag again! The machine must be tricked into adding additional water to wash. It begins to agitate with very little water! Destroying my clothes! Also, I am having to hand wash all my underpants. They do not come out clean. If I could send it back, I would! Feel totally ripped off! I would give 0 stars, if I could!

Bought this Maytag washer from Sears and the salesman told us it was the best washer on the market. Well the Maytag washer is a dud. It leave residue on clothes, clothes come out very wrinkle. This washer does not even have a filter. I would not recommend this washer to anyone. We are very dissatisfied. We dont blame Sears, we blame Maytag for even thinking about putting this washer on the market - Maytag model mav7757aww

Maytag washer. The worst I have ever had... Never again. The tub does not wash, swish nor spin after 2.5 years. Absolutely a waste of our hard earned money... Never ever buy another maytag again. Had a tech come out and wanted to charge almost $500 to repair it. We told him to get out and never come back.

We purchased this terrible machine 2 years ago. The clothes come out worse than when they went in! White powdery stuff all over darks! I always have to wipe all dark pants down with a wet cloth! Absolute junk! Really bad product! Never buying from this company again!

BROKE AFTER 3 YRS. Purchase a new Maytag model: MVWC425BW1 top load washer and dryer after just 3yrs of use. It failed and to find out this is a common problem with these new open drum washers. The bearings go out. Be aware do not purchase them and they also do not wash your clothes good, clothes just stay in same position and you have to wash 2-3 extra washes. It was going to cost 350.00 plus to repair so I purchased Speed Queen that has good reviews. Tech said that top load open barrel washers have been a nightmare.

This Maytag dishwasher is beautiful inside and outside. I love that the controls are hidden. It cleans dishes very well. It has a large capacity for dishes, a rack for glasses/mugs, a small rack for cooking utensils, and a container for silverware. It is so quiet you hardly know it is working. I would highly recommend it.

Maytag Washer 2016 HE top loader. This washer is horrible to use. I hate everything about it. After your clothes are put into the drum and you close lid to start here is what happens EVEN though I select deep water: it puts small amount of water in and then it agitates the whole big load. This is so stupid! Can you imagine a large load of your clothes agitating with a very small amount of water in the drum?So to get around that problem, you have to push pause button and shut the lid after your soap, softener and then listen until that first amount of water fills and agitates, then you have to push pause and quickly put in your clothes. Then you shut the lid and again push the start button so it will fill with more water. Then if youre lucky in at least an hour your load is finally finished. I hate this washer. My boyfriend bought it and I asked him several times to PLEASE return it. He didnt so now were stuck with it for God knows how long. The one good thing about this is I will know to never buy one of these for my house.

Purchased dryer less than 6 months ago and now have an issue with the powder coating bubbling up and flaking off on the dryer drum. Maytag says not covered under warranty unless found in less than 30 days. If I had know that I would not have purchased the dryer.

Just so everyone knows, Maytag, Whirlpool, and Amana washers are all made by the same company and almost all of the internal parts are the same. The differences are mostly cosmetic, its just a way to sell more of the same thing to different classes of people. Just like Chrysler sells Chrysler, Plymouth and Dodge, they all had the same engines, transmissions and electrical systems, just different looks to appeal to different people. I found this out the hard way after purchasing an Amana front loader washer and dryer that broke down on me every other week for a year. I got tired of it and purchased the Maytag 2000 series. This set also breaks down on a regular basis! This is when I found out from the repair company that services these machines that all I did by getting rid of the Amana set and buying the Maytag set was buy a different looking set. Now I am really pissed. This company works for Whirlpool warranty servicing Whirlpool, Amana and Maytag as well as other major brands. All same machines inside the repair man said! Look into it, research it online and call whirlpool for yourselves as I did. You will find it to be true. So if you hate your Maytag, Whirlpool or Amana front loader washer or dryer, research and buy from a different company or you will buy the same old problems again and again.

I purchased it 8 months ago. I have had problems with the machine leaving clothes soaked at the end of cycle. I have contacted Maytag (still under warranty) and they replaced the motor. The first load after repair still had the same problem. They said the check drain was not clogged. The snaked drain has no backups. After every wash, I have to reset the cycle to drain and spin. The machine spins for seconds and fills back up with water and doesnt spin again, but does drain. Clothes are sopping wet at the end of cycle. I contacted Maytag. They said I could be billed for customer education ($129) if they find no problem (threat). I want my money for purchase returned or at least 3/4ths. I expected my new machine to last years, not months.

My machine is only 14 months old and will not even turn on. I opened the lid, and the tub was filled with water and the wet clothes sitting in there. There were only 6 items in there: 3 school skirts and 3 school pants, dripping wet. So I unplugged the unit to try and clear the circuit board - to no avail. The machine will still not turn on. The lights are on, the sensor turns on for about 3 seconds and shut off and everything just sits there. I did not get the extended warranty. My mom still has her Maytag she bought 30 years ago and its running like a champ. Wish I could say the same. I gave my sister my old Maytag - its 25 years old and its still running like a champ. This machine is a LEMON. I will never buy another Maytag again. I am so done with this brand. I hope that a Class Action suit is filed against them.

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

All I can say is what a mistake. Had a front loader that always smelled and had mold around rubber gasket in door. So, wanted a top loader this time after old GE died. Unbelievable, not enough water to clean clothing. Clothing comes out with some dry spots. And the worse thing is washing black items, tiny particles on black pants, shirts, etc. Think is lint not soap but not sure. You have to rub all over the clothing to try and remove. This washer is 8 months old and I have cleaned it with baking soda and vinegar mixture thinking this would help, it doesnt. The spin cycle sounds like a rocket ship taking off. Lots of banging noises during operation also. I have invested a lot of money thinking Maytag is rated high. It is a pretty grey color with glass top. Well I was fooled, not only the saying looks arent everything for people but its true for washing machines. I have gotten multiple mail from co. wanting me to get extended warranty. Think I will, usually dont, cause I think it wont be reliable. Wish I had my washer from the 70s and 80s. Plain old wringer that got things clean. Just put black pants in dryer on very low heat taken out damp cause I dont dry a lot of my clothing. This seems to have helped to remove stains (soap)/ lint. but, talk about wrinkles, oh boy, this machine has that spin cycle going 100 miles a minute. And if you pick a lower spin speed things come out wet. I actually can say I hate this Maytag Bravo. Things dont come out clean, wrinkles beyond control, very loud. Please folks check out your sites on the internet before buying Maytag.

I purchased this machine (Maytag Bravos XL MVWX700XL2 ) about 18 months ago. I was so excited with the looks and the reviews I found on the machine at that time. For the first 14 months I was happy. All of a sudden, it has become the washer from Hades! It twists and almost ruins my clothing. Not to mention, I think it is permanent wrinkles that it puts into things. I washed our comforter on Bulky. The part that must have been at the bottom is completely wrinkled and it also wrecked all of the fill. This was a comforter that it is supposed to be fine to put in the washer. I am attaching pictures in which you can almost plainly see where the comforter was at the bottom. I had a serviceman out a few weeks ago. He said Maytag knows that there is a problem, however, there is no service bulletin that is out yet on it. In addition, he ran all of the codes and told me there is nothing wrong with my machine. That must be why I have to iron almost every piece of clothing in this house. Maytag will hopefully give me decent customer service on this, or I will come unglued. For the price of this washing machine, I expected much more.

Maytag Centennial Impeller HE Washing Machine - The seller left this piece of junk for us. I wondered why because it appeared brand new. After the first washing I knew why. I sure regretted leaving my old set behind. This washing machine wont let you add the amount of water you need. I had to add buckets of water and hope it didnt just empty it out because the sensor controls everything. Twice it just emptied it after I closed the lid and it locked. There is an impeller instead of an agitator. It moves slightly but not enough to move the clothes. To top it off the spin cycle tears into the clothing and twists and wrings it so hard everything is wrinkled with soap residue remaining even on delicate. Each load takes over an hour and the clothes arent even clean. It went to the dump after 4 washes. I went on Craigslist and purchased a used Kenmore and am in heaven. No lock, an agitator, 3 water levels, clean clothing, you can open it and add the missing sock, no sensor controlling how you want to do laundry and no more buckets. Dont buy a Maytag. Look at all of the reviews. They arent exaggerating, they are really that bad. Thank you.

I purchased a Maytag Centennial MVWC360AW washing machine on July 11, 2013 at The Home Depot. I assumed that I was getting a good product based on my Moms old Maytag washer. This machine is the farthest thing from quality that I have ever experienced. My Mom would roll over in her grave if she knew how CHEAP Whirlpool has built---what is supposed to be a---Maytag! The machine worked fairly well, at first. Even though I didnt like the low water arrangement. I like clothes to be fully immersed in water! That went on for 2 years and 5 months, until NOW the led light goes to Rinse, but it wont agitate. Then the led light goes toSpin, but it wont spin! I called a local appliance repairman and he told me that the control is bad. They cost about $250.00. Its not worth repairing!! So, Im stuck with this piece of junk! Shame on Maytag/Whirlpool for building a PIECE OF JUNK!

I owned a Maytag Bravos top loading washer for 8 years, and I loved it. It caught on fire while washing a load. Thank God I was home or it could have burned my house down. Just wanted to post this somewhere to issue a warning.

I cannot even begin to describe my disappointment in these overpriced machines! Bought a 4-year extended warranty when I purchased and two weeks after warranty expired, my heating element went out on the dryer. This repair cost over 300 bucks. Six months later the washer was making some crazy noise and service guy could not find the cause...another $120 bucks. A few months later the same noise...this time a coin had slid under the bottom plate and caused damage to the machine...another service charge of over $200 bucks plus I purchased an extended one year warranty at $189 bucks. Thank goodness, because now it is throwing an LD code and will not drain. Oh and I forgot about the service call for the latch breaking on the dryer door...another $119 bucks. The repair guy felt sorry for me and didnt charge me for the part. Tangled clothes when washed and forever to dry. Next time I will buy an inexpensive set like I had before that lasted 16 years with no problems! This stuff is junk!

I purchased a Maytag Bravos XL washing machine in December 2019. The machine started badly malfunctioning in November 2020. By the time I called for service, they told me the 12-month warranty had expired and I needed a new control board put in for $529! I called Maytag and they agreed to replace the board free of charge, but I had to pay $120 for the service call. They replaced the board, and the new board is faulty. The machine will not fill with water, it wont lock, and now it wont even start. This machine is a LEMON!Now they are saying the soonest they can get a tech out is 1/29/21. Meanwhile, I have a mountain of laundry piling up in my laundry room because I havent had a working washing machine for almost a month. I called to complain and demanded either a refund or a new machine--they will do neither. I used to buy Maytag because of the name, dependability, and customer service. No wonder they were bought by Whirlpool. I WILL NEVER BUY MAYTAG OR WHIRLPOOL AGAIN. I should have looked at all the 1-star ratings online. BUYER BEWARE!

I purchased an expensive front-load washer and dryer a few years ago. About a year after I purchased the washer, there was a foul smell that developed. I contacted Maytag and they informed me of the directions to follow - keep the washer door open when not in use and use Affresh tablets periodically. I followed these directions and was unable to prevent the washer from developing mold in the washer. Id like to file a formal complaint on my washer and dryer. I want a refund on it. I paid way too much money on these units to suffer. Here are the details on my units: Maytag 5000 Series with steam 4.5 cu.ft., Maytag Commercial Technology, Model: MHWE550WW01, Serial: CS00202582, Type: 199-02 732 WT/CR, 12 amps, 120 volts, 60 hz.

We purchased our Maytag dishwasher on 12-26-2013. It was installed in early Jan. We did not buy an additional warranty. We put our faith in the Maytag name. We had no problems with our dishwasher. It was smooth and quiet. The one year warranty ended in Jan. 2015. In March of 2015, our dishwasher control panel began to go crazy. A short while later our Maytag shut down completely. Every now and then the washer will come on by itself. We will try and cut it off. It cuts off when it is ready. We have got quotes on getting it fixed by Maytag. With installation and tax, our Maytag Dishwasher cost us $649.22. Our complaint is the same complaint of thousands of other customers - the control panel. Maytag should have a recall and fix this problem. Maytags remedy for this problem is to sell a warranty for each year that a family owns the dishwasher. That is not acceptable. Please consider a recall on this item. Our model is MDB7749SBW2. Our serial #F33406909. Thanks for your help.

Maytag will not fix 2 major issues with new $700 Maytag dryer bought from Home Depot who takes no responsibility. They wont return it. Maytag wont replace defective dryer unless technician from totem appliances cannot fix problem. The tech ordered a control board and timer. Only installed the timer. He did not fix 2 issues. Dryer never stops at OFF. Dryer leaves damp spots on any clothing whether small or medium large load. Was told by Maytag if damp spots then its OUR problem... our ventilation. No it is your sensor. Our model is ymedc465hwo serial m820. 07331. Bought in late Oct. 2018. Two supervisors later we are being sent to tech or tech company and played games with. All I know is Maytag sells defective dryers then wont replace them or fix main issue.

Our Maytag Elite Series dryer is not under warranty but we have had nothing but issues with this dryer since we have had it. However, now I have holes in the heat intake at the back of the drum. This is so very dangerous and could cause a fire. I am certain this is a manufacturing flaw. How on earth does the inside of a dryer have parts that will not hold up to heat? At any rate, I want it fixed. The only way to fix it is to replace the drum. This has to be a flaw in design or manufacturing and this particular model should be recalled.

I purchased a Maytag dishwasher (Model No. MDB8949SBWO) in September of 2013. Within the first year (and under warranty) the control module failed. The dishwasher is now almost two years old and the second control module has failed. From other postings it is obvious that Maytag has a known defect in their control units. To replace control modules on an annual basis makes this an extremely expensive dishwasher to own.

What a disappointment. I guess this is why we no longer see that commercial about the Maytag repairman being bored. Because now, he is out fixing these pieces of shirt. Im trying to fix my washer (Model: MAH8700AWW), what a sweet pain in the **. Dont do it. Throw it away if it starts making noise like an aircraft landing.

My microwave is just 3 yrs old. SE error. Yeah, what a crock...Such junk. However, if we would just manufacture everything in the USA not only would we get better quality, but we would have more jobs. USA stop selling out to cheaper countries and pumping out more volume for less overhead.

Maytag washer Bravos MCT. Let me tell you your guidelines do not help at all. Would someone please tell me how to get my laundry clean when it doesnt even get all the clothes wet? Looks like Ill have to go to the laundromat at least I can get my clothes wet. You should be ashamed to put out such an inferior product. Worst washer ever.

I bought my Bravos x washer and dryer set three years ago. Ive never been happy with them. You have to put the washer setting on bulky to even wash a normal sized load and they still dont come clean. Only three years old and Ive had problem after problem with the washer. As Im typing this I have a full load of clothes in the washer that will not wash, its full of water and wont even drain and spin. PLUS the lid wont unlock. So aggravated.