We like the refrigerator and we have had it several years. But the thing the top freezer conceals much of the top rack of refrigerator. We must duck and almost kneel to get to food inside. Next fridge will have drawers and doors that open on both sides.

Purchased Maytag dishwasher two years ago from Home Depot. It worked for about six months before it would stop working. When adding a dish after initial start would cause the unit to just die. After unplugging unit for a day the start/cancel drain buttons will flash. After reading online about a demo mode have tried and gotten it to work periodically. I continue to read online and have found there is a diagnostic mode. The settings are in a schematic packed with the unit. I found mine written in French (part #W10321879A). I called Maytag/Whirlpool and asked for the English version. They could not and would not provide me with part #W10321878A the English version, a single sheet of paper. They will only provide to a licensed repair technician. I am only asking for what should have been included in the original purchase. I paid $850 for a dishwasher that is not chump change. I know the control panel is bad but I would like to use it until the new part arrives. I think I may return the control panel and take my losses and go buy a brand that is not owned by Cesspool (Whirlpool).

Fire Hazard - poorly designed with vent at bottom of oven, Warped Drawer and Melted cabinet surface. Nowhere in the install instructions does it say not to mount above drawers. Whirlpool tried to blame dealer. Buyer beware.

I bought a Maytag washing machine September 2017. The lid is cracked. We were told by the repairman today that this is a common problem. The quote for a new lid was over $300. Of course we are not going to spend that much for just a lid. We will be buying a new washing machine and will not be buying a Maytag.

Purchased a Maytag side by side MSB27C2XAM00 in June 2014 to replace a 20 year old Kenmore. After 14 months the fridge stopped keeping things cold in the food compartment and in the freezer. And, the water and ice dispensers stopped working. Called Maytag and they confirmed the fridge was 2 months past the warranty and the best they could do was offer an extended one-year warranty for $325 and set up an appointment. I declined and called a local repair company. They responded promptly and discovered the problem was a bad board. Had to replace the board at a cost of $475 (parts and labor). It was $150 more than the extended warranty but I was already in the hole for $100 service call and I was able to get the fridge repaired on the spot. I had the Kenmore for 20+ years without one repair. Maytag was good for one year and 2 months. Dont know how this company will last with a $2000 product that lasts a year. I can not recommend this product and advise anyone in the market for any appliance to avoid Maytag products.Updated on 11/20/2015: After the board was replaced, the fridge worked but was not keeping either of the side by side compartments cold. They were cool but not cold. Repairman returned. Said it was the compressor which needed to be repaired/replaced. Maytag said the compressor was under a 10 year warranty unlike the other parts of the fridge. Good news, Maytag covered the cost of the part / but bad news that it broke after 14 months of use. However, the service people told me the cost of the compressor was the smallest part of the repair. Labor and service would be costly and Id be better off getting a new fridge with a 5 year warranty contact. After I got over the initial shock of having to toss a 14 month old fridge that cost $1500 and complaining to Maytag, I went to Lowes and found a replacement fridge. This time it was not a Maytag. Moral of the story stay away from Maytag. Dont be fooled by the brand. Avoid them at all costs. And purchase a fridge with a 5yr+ warranty contact!

So far after 5 calls and over two hours spent on calls IMPOSSIBLE to get an answer from Maytag about the correct fill levels of detergent. Consumer support simply do not know and refuse to direct me to anyone or have anyone call that does know answer. WHY SO IMPORTANT? Either you do not get clothes clean OR you damage machine and leave residue on clothes! Neither is acceptable. Using the fill level indicator on Bravos XL dispenser is in direct contradiction to any recommended levels on lids of high efficiency detergent manufacturers like Tide. Per Maytag manual only fill detergent to max fill LINE which is literally about two or three tablespoons of detergent. The lowest possible quantity of Tide per the lines on lid even for smallest load is two or three times the recommended fill level on the dispenser. No one has to be an engineer to know two tablespoons of HE detergent in dispense is going to do same effective cleaning for one shirt or towel as it will with a queen size comforter or very large full capacity load. CORRECT ANSWER DETERMINES IF YOU DAMAGE WASHER OR IF YOU HAVE DIRTY CLOTHES. Googling online there is also no answer. Such a critical answer for Maytag washer to work and clean clothes that is simply not available and documentation is wrong is a huge concern about the viability of this machine and worse their support. Our machine is less than two months old but is obviously over-engineered to the point of just being silly. Tip to Maytag: start selling washboards. More energy efficient, more green except for red and blue bruised knuckles, uses one tenth as much water and users do not need to spend their nest egg savings to buy. Not the first but will be the last Maytag product we will buy. Name may be same but the company is definitely not the company that used to enjoy that name with pride. SUMMARY: Maytag is adamant about using the correct amount of HE detergent OR damage and bad performance by washer and dirty clothes with a detergent residue. With all our best efforts we cannot get what that quantity of detergents is supposed to be. The user manual at best has ambiguous answer. The manual suggest horizontal measure of detergent in tray to max fill level which cannot be right. IF you instead use a vertical measure of how high detergent level comes up to the max fill line the quantity is radically different. It says dispenser holds 3 oz which would be beyond max fill level but nowhere near a vertical fill level.

This is the loudest washing machine Ive ever had!!! I ask the installer if it was suppose to be so loud & he said yes. The machines sounds like metal scraping metal when its washing the clothes.

We purchased the Maytag Atlantis used (4 years old); it looked like new. When I opened the lid, I noticed a terrible smell like some left the clothes in the washer for days. I used white vinegar, baking soda, bleach, anything to try and get rid of the smell. Nothing worked. Finally, my husband took out the agitator and then the drum. Inside and around the drum was lint from all the years of washing clothes. He scraped it all off and bleached it and put it back together and it was okay for a while. It now smells again and I am afraid we will have to keep doing this or our clothes will always smell. I also leave the lid open after a wash so Im not attacked by the smell when we open it. I also had the Maytag Neptune front loader years ago, and the water pooled by the gasket on the door. That smelled too! We will be redoing our laundry area soon and will be shopping for a new washer and dryer. It will not be a Maytag!

Maytag dishwasher mdbh979sam1 - Every single one of the Maytag/whirlpool dishwashers with soft pushbuttons and LEDs will fail--check it on YouTube. They have a very thin printed circuit strip from the door controller to the brains, and this rusts through in a few years. You must buy the whole controller for $150, you cant replace just the ribbon. And youll be doing this every few years. Maytag disavows this if you call them. The design runs the steam past this ribbon, so it corrodes really fast. Get a real pushbutton or a real dial knob model instead. With this model, the issue shows up when the LED pushbuttons stop responding or randomly light.

Maytags reputation for quality is gone. Our Neptune washer has had mold, door lock seized up and wouldnt open, and now our dryer drum is cracked. Exaggerating your products reliability is one thing - this borders on corporate fraud.

We purchased a Model MDB8949SAWO Maytag dishwasher in September 2012. The control panel failed in November 2015. We wrote a letter to Maytag (Whirlpool) expressing our disappointment and received a call from Maytag customer service. The Customer Service representative informed us because we contacted our local repair facility directly, no reimbursements would be provided. During a subsequent follow-up call, I was informed by the Customer Service representative that Maytag manufactures quality products and that no premature failures were occurring with Maytag dishwashers. The Customer Service Representative stated that we should have purchased an extended warranty which lends some support to the fact that Maytag dishwashers are essentially junk. Never again will we purchase any Whirlpool products.

We have owned a Maytag Commercial Centennial washer for 4 years and made the mistake of not buying an extended warranty as we thought Maytag was dependable and a reputable company and thought the manufacturers 10 year limited warranty would cover us. Washer would not spin clothes properly, started making loud noises, lid would not always unlock as time went on, and finally it broke and soaked my tile and it ran through my wall into my hall carpet. Called Maytag and was told we didnt have a 10 year limited parts warranty 6 times (we still have the book that says we do), they offered us a 1 year full warranty for $320.00. We purchased the warranty 11/04/16, Called Maytag as no one knew where the parts were and was told service plan is through AIG. AIG couldnt tell us where the parts were either and when I asked for our refund and we just buy a new washer they advised me they would have to prorate it.Now I feel held hostage. Parts finally come in and Maytag Certified repair man comes to repair machine on 11/30/16, only to be told they could not fix our washer as the screws and transmission rotted and fused to tub. Call Maytag as this should be under my warranty and everyone insists I dont have a warranty. Filed complaint 11/30/16, they sent me a survey on 12/2/16 and I filed my complaint again on the survey. No call from Maytag. Call back on 12/06/16 to be told the survey was them closing my complaint. Now they escalate my complaint and will be called in 48 hours and give me an email address to email my pictures of my warranty. Surprise no call back, so I called them again 12/08/16 and I am advised it takes 3-5 business days. Ask for supervisor and he told me even if I have warranty they will only cover the basket.I will have to pay for technician, and other parts. Still no info on my complaint and you cant talk to anyone just have to wait. I emailed Jeff Fettig CEO of Whirlpool (Whirlpool owns Maytag) as well on 12/6/16 a copy of my complaint with pictures of warranty. The bottom line is Maytag sells junk and their customer service is worse than their product. After being without a washing machine since 11/04/16 we will be buying something Whirlpool does not own which is very limited which is why they can get away with making junk.

I purchased all new appliances and decided to go with Maytag. My Maytag Refrigerator model MFI2569VEM after 12 months, just after the warranty expired, started leaking all over my kitchen floor. I called Maytag and all they told me was there is no recall on this model and there was nothing they could tell me over the phone. I purchased an extended warranty and that is a whole other problem to get someone out. They said to check the freezer problem I need to call when the leak was occurring, so they could see what is happening. So basically, I need to leave water on my kitchen floor so they could see what is happening. Who hires these people?

Had a brand new Maytag MDB4949 dishwasher installed on 10/20/15. Noticed an acrid smell of burning plastic coming from the pull handle. After going to the reviews I see a pattern of shorting control panel boards melting the ribbon cable. Having repaired Xerox copy machines for 17 years, I recognized the smell of an electronics short and melting plastic. There are 600+ complaints for the same thing. Going to call the store we purchased it from and will escalate from there.

I purchased a Maytag Centennial Top Load Washer in February 2012. I wish I had understood the workings of the washer before making the purchase. I am not at all happy that the lid locks as soon as the washer starts and unless I push a button to get the lid open. I cannot open the lid to maybe add more items or check to see if the water amount is sufficient or too much. I have no idea how much goes in for each water level. Of course, I cannot take water out but I could put more in if I see it is not enough. And after learning the water levels, I would know just how to determine the level I need. Some man must have designed the panel. Otherwise I am satisfied. I really like the large load capacity. I originally thought I wanted a front load to get a large capacity but this suits me fine.

It was alright for a while. Then it started ripping up my clothes. The machine is not overloaded, enough water has been added but, when I take the clothes out they are torn. Not a good experience. I have seen several reviews on the Centennials, none of them good. What is the problem. I am hoping my experience gets resolved.

Approx. 3 year old Maytag Dishwasher Control Panel lights blinking with Dishwasher inoperable. Repair part (new Control Panel) costs approx. $180 plus tax. When you add the cost of a service repairman you are nearly at the price of a new dishwasher. I am completely unhappy with this Maytag Product and will never buy another Maytag Product again.

First of all, I had a Maytag for many years and could not have been happier. When it came time to replace, I did not even consider other brands. I have had my dryer for less than a month and the interior already looks dirty. I contacted Home Depot where I purchased it and reported the problem I was having and would like to return this model and purchase a higher end model assuming that it would not have the same problems. Home Depot said all appliances are special orders and can not be returned. I could contact Maytag and have someone come out and look at it for no charge. I contacted Maytag and they told me that they could have someone come out but if they decided it was just cosmetic, there would be nothing that could be done and I would be charged. I said, I am telling you it is cosmetic! Why would I pay someone to tell me that? The guy suggested I take a damp rag to clean it. I said think about all clothes that are being dried are damp!! I will never buy a Maytag again and will not buy any appliances from Home Depot!

Never dies, never have had to have it serviced. House burned down is reason why it died. So I rebuilt, bought another one, then moved took it with me, then left it with my daughter and moved to Mexico. The dryer is still working to date and this all happened over 10 years ago. I sooo want another one. Best brand period. I only buy Maytag as they last. Unfortunately I do not have one now as they were unavailable in this country so bought something different. I was told the machine I have currently was as good as a maytag - they lied. I recently found out they have them now, so when I can afford one again, I will purchase one.

Model# MVWB850WQ0, Serial# CY4070329, Type 580-02. Bought this Commercial Technology washer 2-1/2 years ago thinking the commercial model would be heavy duty. It was only heavy on the wallet. The washer started to emit a loud roaring sound two weeks ago that never happened before. It happens on spin cycle. We cant even have a normal conversation in the house. After reading similar problems and outrageous cost to repair, Im leaning to look for a replacement without the Maytag label. My 10+ year old Sears Kenmore didnt have any problems. My mistake was to replace it with a more efficient washer. I guess New+Efficient doesnt equal long lasting for Maytag. You would think a major manufacturer would put in heavy duty bearings in a washing machine. Heck, maybe the bearings are heavy duty but design shortens bearing life. Enough time spent on Maytag. Stay away!

We purchased a Bravo Maytag series top load washer from Sears in June 22nd 2013. See receipt for verification of sale. It seemed to be alright and we were hoping to be a lucky consumer, but now it is January 2015 and today I could smell smoke along with a weird smell (like an auto repair shop smell). I immediately was concerned about the entire house catching fire. Luckily I figured out the smell was coming from the washer and was able to pause it, stop, and then turn off. We are not happy. Our whole main level smells awful. And Im pregnant so this is probably not good to be inhaling. We are looking for recalls that may be out but weve only seen front load recalls not top loaders. When we bought this it had great reviews, but now it appears there are so many complaints, so my question is: Why isnt Maytag doing something about this massive problem?

I had a warranty that I bought over a year ago. The dishwasher since then has been a monster beyond control. I called Maytag and the woman asked how long it has been acting up. I said about a year, but I was not sure. They refused to honor my warranty because they said it would only go into effect 60 days after I purchased it. They are translating about a year as an absolute and refused to honor the warranty. I would never ever buy a Maytag product again. Never. I will contact every person I know not to buy such a faulty product.

Purchased MAYTAG DISHWASHER MDB7809awm in 2011 for $719. In 06/2013 the far right 3 buttons stopped working. I contacted Maytag to see if there was an issue with this and they reported that there was not. I had the part replaced in 06/2013 at $280. It cost me 1/3 of the purchase price of the dishwasher. The repairman said that he sees this a lot with Maytag control panel issues.On 08/02/14 the same exact issue occurred. I contacted Maytag online on 08/02/14 and didnt hear back until 8/13/14 to say that there was no known issue and all they could do was recommend a repairman. I also called before I heard back via email and they said the same exact thing, there is no known issue and we can do is recommend a repairman. I am not interested in repairing. Been there, done that. Not doing it again. I researched the issue of the 3 far right buttons not working and there are several forums and discussion topics out there. I find it hard to believe that MAYTAG is not aware of this issue. If you GOOGLE the model you will see the same issue. Not only is the MAYTAG product poor, but they have the worst customer service I have ever seen.

Fifteen months after purchase, the lid lock and motherboard goes off. It was replaced with new parts and the machine still doesnt work. Cost of repair is equal to the cost of the machine. With or without an extended warranty, the expense is not worth the investment. While shopping to replace the machine, the dealer finished my sentences on Maytag washers.

I purchased My Maytag Washer and Dryer set from Lowe's, which was a very good experience all the way, back in June 2017. After two years I can finally give an honest review. We love this set even though it is not as quiet as the old Maytag washers. Still is but not as. We have not had one bit of trouble from either the washer or dryer. The next size larger would have been the better choice for us since we now have king size bedspreads to wash. It still does the job though, just one piece at a time. A lot of people complain about the smaller amount of water used but it still cleans clothes quite well. If you need more water just use deep water wash or for even more water use the setting for bulky sheets which really fills up the water level.

We purchased our Maytag Bravos washer/dryer in January of 2012. In October of 2013, I noticed that the lid would not close properly. In examining the lid, we discovered that the screws were in tact but the information panel on the inside of the lid had come unglued causing the lid to be obstructed from closing properly. After calling Maytag we were told that they make a quality product and, in what I consider to be a condescending reply, could not help us. Replacement of the lid with the service call would cost almost the cost of this expensive washer. So disappointed in what we thought was a wise purchase!

Due to our previous washer breaking down, we had to purchase a new washer. We have always been loyal to Maytag since we were always pleased and satisfied with the performance. However, this new washer does not deliver in performance, cleanliness, energy savings when cycles take much longer and you end up maybe not using as much water, but our electric bill has gone up considerably. I have nothing good to report about this washer. We purchased it back in April of 2013, and Ive given it the benefit of the doubt by experimenting with all the different wash cycles. I am just not happy with it. I so want to trade it in for a front loader and give Maytag one more chance.

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

I bought my Bravos washer (Maytag Bravos Model # MVWX700XL2) back in 2013. Worst mistake ever, First off the clothes never came out clean, regardless of how diligent I was following the directions on how to use this particular type of machine. Secondly, it started going off balance for every load if I put more than 4 pieces of clothing in. 2 months after having it recently repaired AGAIN for not spinning and going off balance, it is doing it again. It is only 4 years old! I bought it for the Maytag reputation, but now I am doubting that reliability.

MBD7709AWB2 - Bottom line, every 1.5 years (18 months) you will have to buy a control panel. Number 3 for me cost me $149.00. Now my wash cycle will not kick on. Do I have to tell you what dishwasher not to buy!

We bought our Maytag dishwasher at Sears about 2 years ago. It has never cleaned very well, we have to rinse everything almost to the point of spotless before we load it. Its a water saver, which means it takes more than 4 hours to fully cycle. Just today, I went to turn it on and the start button does not work. I looked it up and found that this is a common problem with new Maytag washers. This is really irritating, considering we paid a lot more for the Maytag brand than we would have paid for something without the Maytag reputation. Live and learn, I guess; we certainly will not be buying another Maytag.

The control panel of my dishwasher is malfunctioning. I looked this up online and ran into a recall for the heating element. Sure enough, my dishwasher is effected. I asked why I was not contacted. First they made up a story as to not having my contact information. This is simply not true, as I purchased the dishwasher directly from Maytag. Three years ago there was another recall and the heating element caused another problem so Maytag replaced my dishwasher.If a heating element overheats, it seems to me that a short-term affect could be overheating the control panel, causing it to malfunction. I read through a few recent complains and would also like to inquire about having this issue looked into by the Consumer Affairs.

Bought a Maytag microwave model MMV4205DS and I too have had an issue with open/close door display. Just like other reviews Ive read it started out once in a while for the first year then began happening more often til it stopped working by the second year. I also read someone asking why there isnt a class action lawsuit? Good question. Way too many bad reviews on same issue. If I knew how and if we could start one then I would. Thought we could trust a company thats been around for so many years. Wish we had check into it more and I have learned from other products to do just that from now on. Have a backup microwave by GE from WalMart weve had for 10 yrs still working.

Everything in my house is Maytag. I assumed they were the best. My dishwasher went out after three years, and I replaced it with a Maytag. Now, my over the range microwave is not working. I will not replace it with Maytag. I expect my washer and dryer to be next.

I purchased a Maytag washer 5 months ago. I noticed the washer was not putting enough water in the machine to cover my clothes, and at the end of cycle my clothes would be all tangled up. A repairman looked at it and said there was nothing he could do. Do not buy this washer. It is a lemon. I even spoke to the main customer service representative, he was the most arrogant man I have ever felt with. He basically said deal with it. I want. I want my money back so I can purchase a washer that actually works.

Maytag is the worst washer company. I owned my washer for two years and I had two different problems with it and now I have a 3rd. The first was the same day they delivered the washer, I needed a wire harness. I should have returned it then but I didnt. The 2nd was six months after the first one. A wire came loose due to the washer shaking and the 3rd, Im not sure why it wont drain but the tub is full of water. I called Maytag and they really didnt care as long as they got their money. They referred me to three companies that fixes washer. Two of three was already out for this washer. If I didnt know any better I would think Maytag gets paid off for every customer they referred to these companies. I would never buy another Maytag Bravo or Whirlpool product. Im very dissatisfied with their Bravo washers. They lost a long time customer.

Top of the line $1300 Maytag Maxima MGD8100DW probably rusted much earlier before I noticed. After all how many times you check the drum of brand new top of the line dryer?? Manufacturer says not covered. Not sure but already this brand new model has been discontinued, so the manufacturer i.e. Maytag or Whirlpool take your pick found out about the defective design/part but now does not want to honor the warranty ridiculous. And one of the main selling points was made in USA (which turned out to be only assembled in USA), and the consumer reports which gave good rating but they were duped too.

Purchased 2/13. Used maybe 3 times per week. Panel has gone haywire 6/14. 3 months out of warranty. Confirmed, bad control panel. We need class action lawsuit. This is ridiculous! Same issue with hundreds, likely many more unreported of dishwashers from Frigidaire/Maytag. I found number to law firm preparing suit... **.

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

Our Maytag Elite Series dryer is not under warranty but we have had nothing but issues with this dryer since we have had it. However, now I have holes in the heat intake at the back of the drum. This is so very dangerous and could cause a fire. I am certain this is a manufacturing flaw. How on earth does the inside of a dryer have parts that will not hold up to heat? At any rate, I want it fixed. The only way to fix it is to replace the drum. This has to be a flaw in design or manufacturing and this particular model should be recalled.

MCBH979SAB0 - I am also frustrated with Maytag for the same exact problem... the control panel and the dishwasher not working just after our year warranty went out. I purchased this product because of a recall on my former Maytag dishwasher. I was told I should purchase this new model to replace it, only to get fooled again. This seems like BAD business on Maytag! How can we get an official complaint to someone who can fix this? Why would a company like Home Depot continue to support this business!!

The top loader washer Commercial Technology washes very small loads well. I bought it for the deepwater wash. It DOES NOT work. It also has a auto sensing. Hate this washer. I have to pour buckets of water in the wash to fill it. Maytag/Whirlpool go back to the way it should be. If I want a full washer I should have it! At the end of the day IT IS MY WATER BILL!

We purchased a refrigerator in December 2010 with a 12-month warranty. Since the refrigerator was delivered, we have experienced nothing but problems. Most recently, there was a problem with the auto defrost causing us to lose all our food stored. It also caused water damage to our floor. We scheduled maintenance with a contracted company through MayTag. After three scheduled visits, which made me miss 3 and a half days of work resulting in an additional loss of over $300, our refrigerator is still broken and they just want us to schedule another maintenance visit. When calling Maytag customer service we are literally told, “your loss, there is nothing we can do to resolve your issue, we can only continue to send out maintenance.” I am so disappointed in this company, the product, the customer service, maintenance service etc.

I purchased a Maytag refrigerator from Home Depot on 5/17/11. It would run, then not run. It spoiled all the food not in the freezer and most of the food in the freezer. This happened early November, being less than six months old. My wife called on 11/8/11, they repaired it on 11/18/11. Ten days of no refrigerator and a lost of about $200 in spoiled food. The company would not pay for any of the money I lost for the spoiled food!

We purchased the Maytag double oven 30 inch 5 burner, stainless steel, model MGT8885XS. Oven worked good for six weeks. The igniter broke in the bottom oven and when the third party non-Maytag repairman came out to fix it, he was unable to remove the bottom oven door. It is not flush and heat escapes when the bottom oven is on and it causes the top oven to get condensation. The repair man was directed from a technician from Whirlpool that he had to order a new seal and hinges. I dont want it fixed. I want a new one. I have called Customer Service for Whirlpool and the third party and the store in which I bought it from and everyone is pushing it off onto someone else. Customer service is poor and stated they will only fix the oven and will not send us a new oven. We sent our rebate in the mail which was to arrive within 8 weeks and we have yet to receive it. Very poor customer service. Glad I purchased the 4 year warranty. I will never buy Maytag again.

I purchased these appliances on 02-10-16 from Home Depot in Loganville Ga., for almost $2000.00. I filed the first repair call less than 3 weeks after delivery. The sensor panel was bad and had to be replaced. Now 8 months later the washer is not starting, AGAIN. The dryer will only dry one load a day or you get the AF code. This means that the dryer cannot push air over 5 or so and we need to have a vent booster fan (an additional $200.00) installed plus have an electrician run a new outlet. I returned to Home Depot with my complaint. Feeling that I have an inferior product, they tried to get Maytag to make it right. Maytag refused to offer any solutions whatsoever. Home Depot refunded a little over $300.00 for my inconvenience.The washer is an absolute ill-conceived piece of junk. It is ROUGH on clothing and does not remove soap. I started out with brand new (expensive) towels when I purchased this machine and 8 months later all of the hems have been snatched off and theyre unraveling and falling apart and are slowly becoming car wash towels.You cannot wash delicates in this machine and allow it to spin. Underwires in bras are badly misshaped or broken completely. You cannot wear them afterwards without being gouged by bent wires. The only way around this is to take away the spin cycle, but you better be ready with a clean garbage can to haul the dripping clothes elsewhere and hung up to drip dry. The washer has NEVER removed all of the soap from bed sheets. I have a dark gray set that show the soap best. Now I have to wash once with soap then wash again with no soap. This negates the machines being efficient.Unfortunately, I found the negative reviews AFTER buying the machine. My complaints are well known to Maytag, seeing has to how the same complaints are found online as far back as 8 years ago. I have been brand loyal for 30+ years to Whirlpool and thought that I was moving up with a Maytag, based on my parents 50 year experience... I was wrong! I will never purchase another Maytag product nor Whirlpool since Whirlpool now owns Maytag. I have researched and am of the opinion that Speed Queen is a far better product and plan to junk this set and replace them with Speed Queen.

When purchasing a microwave for our kitchen the Maytag MMV4203DB00 had all the functions I wanted. Just after a year its quite cooking. The fan would still run but not heat anything. I called Maytag and was told basically, tough luck. I said something about Maytag, that it was supposed to be a great brand and should last longer than 1 year. The part to fix it plus labor was going to cost nearly as much as a new microwave to replace it. Now, the microwave has started to turn on by itself. Customer service was very rude and came off with a we dont really care attitude. I will never buy Maytag again.

I have had my washer and dryer for more than 5 years. As normal, over time, stuff wears out and parts need to be replaced. The manual doesnt list part numbers that are needed. The website doesnt pull up part numbers when you type in the model number. After paying for overnight shipping that isnt guaranteed (and was more than the part itself), it didnt show up until a couple of days later and it was the wrong part. I would have to pay for shipping costs of the return, now tripling the cost of the actual part. Calls to customer service were not at all helpful as all they could say was that I would have to pay for the return shipping and they were sorry there was nothing they could do. I wont be purchasing anything from Maytag ever again.

I purchased both the washer and dryer in this series. First the washer does a horrible job actually cleaning the clothes unless you set it as a bulky load and use more water. Despite that issue, after only owning the set for four years the dryer broke down. It made a terrible noise and you could not run it because it was far too noisy. My husband thankfully bought a replacement part and fixed that issue. A few months later I started having trouble with the washing machine. It freezes constantly and I have to unplug to get it working again. It usually take over 15 times to actually get it to begin to fill with water. Now it started to stop working during the wash cycle and I have to unplug it again to get it going. Most times I have to change it to another setting like rinse and spin or drain and spin to complete a wash cycle. Last night it began to have a plastic burning smell. I used to own the same washer for 20 years and only had minor issues that come with extended use. To only own this pair for under five years and have them both break down proves that these are poorly made products and you should save your money and purchase a different brand altogether. I will never buy another Maytag as long as I live if this is how well their products are made. I expect to have my appliances last longer than five years for their price. So save your money when it comes to these machines. I promise you will not be happy with your purchase. I will either have to repair the washer and hope it will last at least a few more years or chalk this up to a lesson learned and discard both machines.

I purchased a 5 Maytag appliances in the last year. Stupidest thing I have ever done. The clothes washer being the worst. Front Load, model # MHW3505FW1. Last night I threw 5 small, lighter weight things in the washer on normal cycle, med temp, max extract... like usual. An hour and thirty-eight minutes later (normal cycle time), I opened it to find most things never even got wet. One scarf was still folded in fourth - the way I put it in! I called service even though I know there is nothing wrong with the washer, other than being so poorly designed, it cant get clothes wet with a damn tub and a hose. After I told her the problem, she puts me on hold, comes back to tell me she researched this everywhere and she found that this is a symptom of a NEW washer! Its SOO efficient that you cant even tell it was wet! Bull. Most of the items were brand new and you could see the original creases and smell the new smell. They CLEARLY were never wet. They wanted to set up an appointment for servicing, so now I have to be here for them to tell me nothing its not broken. I will never buy another Maytag again.

We bought a new Maytag electric range from a local dealer three years ago. The oven element quit working, which shorted out the motherboard that controls the entire range. The cost of repair was $500 for the element, motherboard and installation. We have owned other brands that lasted 20 years and worked fine with no repairs. My folks have used Maytag for over 50 years with no problems. Who and where is this junk manufactured now? China? I will never buy another Maytag product!

Its an old story with Maytag. We purchased a refrigerator in Nov 2012. Three days ago we noticed the refrigerator was making a constant buzzing sound and that the freezer was not cold. A repairman confirmed our suspicions. Bad compressor! Cost to repair, $729. And, the warranty on the new compressor was only 90 days. Cost for a new one $1700. Contacted Maytag. We do offer extended warranties (up to 10 years on compressors) on some models, but not yours. So, we will get a new one but with the extended warranty. It wont be a Maytag.

Our problem started when the control lock button locked itself on. Called Maytag and told it wasnt covered by warranty but they did walk us through resetting the power and it fixed the problem until we ran the next load. Now when you try and set it, the rinse only light comes on. Bought the Maytag because I always believed them to be dependable - wrong!! I had a basic model Whirlpool running for a family of 5 for 25 years prior to this Maytag without ever having to call a repair person. Maytag wont deal with the issue so I would recommend to anyone else having any issues with unreliable appliances to do what I am doing - boycotting Maytag!!

The machine dries out the clothes so tight that they are full of wrinkles. I am so dissatisfied with this machine, I spent almost $600.00 for this and this is what I get. I also end up with fabric softener all over the clothes. I use the Downy Ball and I just took out my black pants to find blue all over them. I contacted Home Depot where I purchased the machine. They said to get a hold of you. All I want is get a different machine, not an HE. This is beyond anything. Someone should have to put up with, can you help me?

I purchased my Maytag Centennial 1 and 6 mos ago and it is already broken. The washer wont wash the clothes, just sit in the water and wont spin. I called Maytag, they offered me a warranty for another year for $371. The washer was only $550.00. When I tried to get set up with a repair service, the only company they used which was going to charge $105 just to look at it, would only take cash. When I called back to discuss with Maytag, they were no help at all. I was told they wouldnt even do the warranty since I scheduled a service even though I canceled it. I will never buy Maytag again.

My Maytag refrigerator (bottom freezer) is about four years old now. Since the first year, it has been freezing up. The refrigerator gets warm and the freezer stays cold. Two repairmen have looked at it, replaced the electric panel and the thermostat - neither repair fixed the problem. If you completely defrost it, it will start working again. For about three years, it would work for a few months, but now it will only run for about two weeks before freezing up again. I called Maytag when this first started happening and again recently. They say they have never heard of anyone having this problem and they are sorry. The woman said she would put my complaint in my file. I certainly would recommend that people avoid Maytag refrigerators.

Purchased a Maytag range with Aqualift technology in 2013 thinking it was a good brand and *happy* to find a new way to self-clean my oven. This turns out to be nothing but a joke and I am not *happy* with it. After following directions to the letter, there is some loosening of anything on the floor of the oven, but the sides and top are slowly being coated with more and more grease. Ive spent way too much time with my head in the oven trying to scrub stuff without using a heavy duty cleaner but feel I now need to resort to Easy Off as there is no other way to get it clean. I also dont understand why they tell you to remove the racks since there obviously isnt enough going on to even clean the oven... How would the racks be damaged? And now I believe there is a problem with the Dual Choice element where Im not able to turn the temperature down. Even turned back to the low setting, the pan cooks away like its on high. I have to keep turning it off and then back on in an attempt to find something similar to medium or low heat. Im so very disappointed in Maytag and feel this method of oven cleaning should never have been put on the market. Its a scam!

Well, Im confused and nervous! Ive read the reviews and I LOVE my Bravos washer - cleans unbelievable, its quiet, no rattling of pipes. My daughter was highly impressed when she was visiting with her daughters. She told me my washer got stains out of her kids clothes that her washer could not! Im confused because of the number of bad reviews for this washer - maybe they changed the washer? Mine is about 3 years old and I am SO happy with it! No agitator, but cleans so well. Terrified if it dies on me, I wont be able to replace it.

I purchased a Maytag 2000 series washing machines. It broke and needed to be repaired within six months of purchase. It continued to break and need to be repaired numerous times and its only a little over 1 1/2 years old. It ripped and ruined clothing on numerous occasions. It would not drain and the door would lock with clothing inside thus ruining them. Both of these issues occurred on more than one occasion. Maytags solution for their defective washer was to keep referring me to my warranty. They were no help at all. My warranty finally came through for me and I was issued a full refund through the warranty I purchased at the time I purchased the washer. My new washer (which is not a Maytag) is being delivered Friday. So finally after being without a washer for over two weeks I will be able to wash clothes again. My experience with Maytag was frustrating and aggravating to say the least and I will definitely never purchase Maytag again. They are far from reliable.

My front load Kenmore just fell apart. I guess Im lucky I have had it for 8 years and now its broke. I could fix it but thought it would be better to get a new one. I looked at all the reviews for front load washer and could not find one that had positive reviews. So I went with a top load. After reading all the complaints I might have made a mistake, but its too late now as it was delivered yesterday and now doing the clean cycle. Oh my…what junk they all produce now - a true throwaway society. My refrigerator is still working after 24 years what a gem of a product. Happy days.

In October 2017, I purchased a Maytag MVWB765FW0, thinking that it would live up to the Maytag reputation but I will NEVER buy Maytag again. This machine is more suitable to wash industrial canvas rather than clothing and bedding. All the laundry is twisted and mangled and ends up in a large tangled ball at the bottom of the tub. My clothing is being destroyed faster than I can replace it.

On April 8, 2017 I was sitting in my Dining room with Dishwasher in the kitchen in cycle cleaning. All of a sudden I heard electrical sizzling and turned to see my Dishwasher was on fire. I got up and opened the door and my Husband shut off the circuit breaker for the Dishwasher. He raced to turn off water under sink and went to disconnect the dishwasher when all of a sudden hot water was shooting all over the place. I tried to catch in a bucket but it was so hot and shooting out hose fast. Kitchen and Dining room were then filled with water. He realized the turnoff under sink was installed at time of house built and cant be fixed without a lot of chopping up under cement.Well finally we cleaned up the mess with mop and towels and relieved neither one of us fell at our age. He unconnected the Dishwasher and secured outside. About 2010 there was a recall on this model Maytag. I reported it and a repair man came to change the cycle panel and said it would be fine, not. Yes almost 7 years later a fire occurred. Just glad we caught it in time without losing our lives or my house. Never, never again will I purchase a Maytag.

I bought a Maytag washer from Lowes and bought the extended warranty. The warranty expired but Maytag is not taking responsibility for the lemons that they sell. I have seen many reviews stating that the bearings went on the washer. This is what happened to me and it happened twice already. I spent 798.00 on this washer thinking it would last for more than 6 yrs. They offered me a warranty for 368.00 or to purchase another washer at a discount price. Of course I refused but I want everyone to be aware of Maytag Washers - not worth the money.

Maytag Bravos Quiet series 300 washer - I purchased this washer 14 months ago from LOWES. After having a huge issue with a Kenmore Oasis machine. $$$. Anyway, this machine started a week ago with F1 code and Ld code. This is getting to be a financial strain buying washers every year or two. This is my third in 5 years. Looks like I will need to get another one, again. It makes no sense to repair it at a high cost when the replacement parts are the same as the failed parts. Everyone seems to have the same problem with this washer. Get better electronics guys. The rest of the machine is in fantastic shape. My two cents.

We bought a Maytag refrigerator. Big big mistake. It bangs, makes all kinds of noises. The bottom freezer has ice that builds up once in a while, has to be unloaded and thawed out. We have had several service calls and they do not know whats wrong. Trouble started about a month out of warranty. Called Maytag and they would not do anything. WE are very disappointed in Maytag. We spent more money to get a good product and ended up with junk. We are getting rid of it and buying one that is made by a company that knows what they are doing.

We purchased a new Maytag washer and dryer from Home Depot; a couple months later the dryer started to rattle so we contacted Maytag and they sent a service tech out who stated this was normal as the dryer was settling and parts are not as tight as they are when new. This was a garbage response and he was asked to leave. I contact Maytag again, told them of the problem and the tech response and they offered to send another tech out except I would have to pay for the service call since they already sent someone out. I sent them an audio file of the rattle, no reply. Eventually Home Depot ended up replacing the dryer as Maytag refused to help me despite it being in the warranty period.

I have just inquired on this site about problems with Maytag dishwashers. Ours does not start. It is about a year old and is Model MDBH989AW03. I am very discouraged after reading the many continual problems with control panels. I am checking my warranty. If it is out of warranty, we think that we will purchase a GE that has worked great in our other house.

My refrigerator is several years old, and I would buy the same brand when I need a new one, although I would hopefully buy a counter depth one because my kitchen is so small, and the one I have now is kind of big for the space.

Bought in July 2015, brand new from Lowe’s or Sears. When working to its full potential it never cleaned clothing very well, had no designated spot for detergent or softener, just bleach. Just last 3 years and it’s a piece of crap that has to be replaced. Going to argue with the company to tomorrow to get them to replace the broken transmission which may or may not be considered part of the drive motor - all **. This is a very expensive machine that didn’t last a month beyond 3 years! The 10 year warranty covers the 2 most rugged parts of any washer... the agitator never truly cleaned my clothes and now it is fused to the wash basket and cannot even be replaced without being chiseled off. Worst machine, purchase, and brand ever???

Worst brand ever. They both broke at the same time. Spend too much money. Never buying these brand again. Maytag sucks. Dont buy Maytag washers or dryers.

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

Maytag is supposed to be the best. I wanted a top loader again. This washer is almost worthless because of the water control. I have to add buckets of water before I start the washer. Otherwise the clothes are not clean. The cycles are strange with the amount of agitation. I will continue looking for an OLD model. DO NOT BUY THIS WASHER.

We have had 2 sets of Maytag washer & dryers. Our first set was a top load. When we bought the Neptune front load machines we gave the top load to our daughter and it still runs great after 14 years! Our front load W&D are 7 years old. We have a dog breeding business and when we have puppies the W&D pretty much run nonstop for 16 hours a day or longer. The blankets and towels come out like new every time!! The only complaint I have is the top of the front load machines seem to be plastic and scratched really easy. But the enamel on the top load still looks new! We plan on shopping for a new set this weekend passing these on to our daughter. We will buy ONLY Maytag for the rest of our lives!!

Bought Maytag Electronic Washer and Dryer on Feb. 7th 2020. On July 10th control board went out in dryer. 3 weeks without a dryer and hanging clothes in 112-118 degree weather in Arizona. I am 77 years old and too old for this. Dont buy Maytag!!. Had Whirlpool Washer and Dryer for 22 years. Never a problem, regret buying a Maytag.

In 2011 we purchased a complete appliance grouping at Home Depot by Maytag to include the dishwasher. For some reason we neglected to purchase an extended warranty on the dishwasher. Lo and behold in 2013 our control panel went bad and the cost to repair it was almost as much as purchasing a new dishwasher. Thinking this was a fluke we were dumb enough to purchase another Maytag from Home Depot due to the loyalty made in the USA. Well here we are 2015 not even a full two years later the control panel started acting funny a few days ago and yesterday just plain old QUIT. Fortunately we were wise enough to purchase an extended warranty plan on this dishwasher so tomorrow we will be calling the repairman. Unfortunately Maytag has never solved the problem that has been occurring for at least 5 years and continues to sell this product to unsuspecting schmucks like us who try to be true to the made in the USA slogan. Shame on Maytag!!! Our model number is MDB7749SBM. Buyers beware.

Built a new house, bought new appliances for the kitchen. Like others, did all the research, wanted to buy American made. Wow, did we ever make a mistake. Refrigerator is just over 2 years old. It is worthless. Repairman, Maytag Certified, says that it appears to be internal problems and probably come from the factory that way. He suggested I contact Maytag directly and they should be able to make things right for me and my family.So, I called, sat on hold for 10-15 minutes, and was finally connected to a customer service employee. I explained all that I knew about the problem, she pulled the repairmans notes and the notes of the technician that had spoken with the repairman. After reviewing the file, she informed me that my 2-year-old refrigerator was out of warranty and there was nothing that could be done.What ever happened to American Made companies standing behind their product? I didnt spend $2000 on a refrigerator that would last me 2 years. I expected 7-10 years, AT LEAST! I expected a company with the name MAYTAG to show some shame for creating a piece of junk and charging a customer this much money for something they know is obviously flawed from the factory. Shame? No. Guilt? None whatsoever.Caution to those considering a Maytag product. Run away! Go find a more reputable company. Go find a company who views customer service and quality products as a priority. I didnt purchase the cheapest refrigerator on purpose. I paid extra for American made and what I thought was a quality product sold by a quality company. Reality has now set in.

I have trusted Maytag for many years, more than 60 years, my parents and then myself. My Dad always told me I could trust Maytag over any other brand and that has always been true until I bought a new Centennial Econoserve Washer. This is without question the worst machine ever made. I should have asked every question in the book concerning this machine but, oh no, I just trusted the name MAYTAG. I am so sorry. I cant trust it to clean anything that shows it needs cleaning so you have to wonder what does it clean that you cant see. Im sorry people, I just dont know what to do. I cant afford to buy a new machine and the store I purchased are basically telling me, Sorry, you bought a stripped down model. Too bad! I will never buy another appliance from that store nor will I recommend them to anyone. Too bad since they are locally owned. Anyway, Maytag, you blew it badly to turn out this terrible machine. Thats my story and Im sticking to it. Better product next time.

Washer purchased in May 2013 last month it stopped completing the drain and spin cycle and cloth stayed wet. To have the machine repaired, we would have to replace the control panel. The cost of replacing the control panel plus the service call was 76% of the cost of buying a brand new machine. As such we are disposing of the machine and will be purchasing a competitive product.

It does not completely drain all water out of until. So unless your running the washer every day, you will end up with the most horrible smell coming from standing water. It is very irritating and so fowl smelling.

I bought two sets of Maytag washer and dryer. We have had them for less than a year and the tubs had to be replaced out of both of them. Now, its less than six months later and they are doing the same thing, so the tubs have to be replaced again. What kind of equipment are you making? This is just an outrage. You are scamming people to buy your products by your so called advertising and rep. Well, this is false advertising on your part. I will never buy another Maytag anything or Whirlpool either. I also see there are a lot of others having the same thing being done to them. I would be ashamed to even have these products to sell. Shame on you. Scammer.

No matter what we we do we still have soap residue left on clothes, even when we do the 2nd rinse cycle (what a waste of water). We use the correct amount of HE detergent and we use the detergent dispenser but it doesnt helps. The machine just doesnt use enough water. We have removed items that still have DRY SPOTS on them when the cycle is done. Areas that have never gotten wet after a 45 minute cycle. Never once had this happen with an agitator machine. Would not buy this machine again. Model: C80441070. Serial #: MVWX655DW1.

The refrigerator works well. No problems. Easy to move to clean behind it. Good value. I havent had any problems since I bought it. Keeps a steady temp; Its exactly the size I needed; has plenty of space. Its a plain fridge with a reasonable price!

We had the same problem that everyone is complaining about re: frozen water in bottom of freezer dripping out onto floor. Swore when I got rid of the Maytag smooth top stove that broke after 5 years that I would never get another Maytag but broke down and bought this fridge. Maytag rep made it clear that the Fridge had a NOTE on file about the drain, but it was NOT a product recall. So after virtually taking the freezer apart before the repairman came, we ended up paying $120.00 for the repair, not the part. Yippee. Please note that the repairman told us we saved a lot of money by taking apart the freezer so most repairs probably cost a lot more than ours.

I purchased this washer in Oct. of 2017. From the beginning, it has not cleaned clothing properly and leaves a white residue on clothing. To get the residue off, I must wash the clothing again or sometimes it will come off in the dryer. The water level is too low to efficiently clean. I thought I would save water getting this but not at the price of multiple washes... What good is that? Since there is no agitator the clothes just sit at the bottom and move back and forth as one big clump, with just a few inches of water. I am sorry Ive waited so long since I am now past the point of returning this piece of junk.

Thank you all for taking the time to write these reviews. My only regret is that I am reading it now, I wish I would have read it before purchasing my own Maytag washer and dryer... I bought a Maytag MVC565FWI / YMEDC555DW1 washer and dryer duo in December 2018. I had some holes in my sons clothing, but thought maybe they were due to him being a boy of 17 year old in college, sitting all day... Also my dryer was barely drying.Called and had a 1st technician for the dryer issue. He said no wrong code and to try and clean the evacuation vent. As I am a renter, I contacted my owner to do so and he did. But I did not get to try the machine unfortunately since 5 days after the technicians visit, I was deploying to Africa. I am military and was deployed for 8 months. Upon me return, dryer still barely dries and HOLES in every load of laundry that I do. My sons and also my own clothing. This time, there is no mistaking articles that I put in came out with huge circular holes.A second visit with a technician is arranged, last Tuesday October 8th 2019. Still no codes are found. And technician suggests cleaning the conduct better. Again my owner does so. Again, up to 4 cycles of 60 min on High heat to dry articles. No economy on energy on these models! I have called Maytag today since no one has contacted me in a week for my wrecked clothing. To my request of having my appliances either replace or refunded, they say no. Policy is to send a technician. Again. After 2 visits of technical support, Maytag is sending me for a 3rd time a technician (at my cost if nothing is found again) to test the appliances. Since the technicians can not find a code on his machine, Maytag is telling me they will do nothing.I have a washer dryer that wrecks my clothing and does not dry them. (Also I feel like my clothing are never fresh scenting, I wonder how efficient they are with even the basic cleaning part..) I will have to put them in the garbage, because how can I sell them?! Talking to Maytag, is being treated like an infant that does not understand THEM, when in reality, they do not back their products at all. I feel left alone with brand new machines that have been used around 30 times in under 1 year, that I will have to through away in the dump and never ever buy from this company again. M.

Food freezes in the refrigerator. If I turn it down, the freezer does not freeze. What has happened to the quality of Maytag? This unit is so new. I think I am going to take it back and buy a better brand!

I had a stackable Maytag dryer that was bought in 2016 but only used during the summer of 2017. Last May the dryer stopped heating. I contacted Maytag and they sent a repairman a week or so later. He identified the problem in the electronic control and ordered a replacement part. The part came and he installed it a week later. The part was faulty and he ordered a replacement for the replacement. It arrived a week later and also did not work. He said he had problems with replacement parts but contacted the technical service department at Maytag as he did the first time. The technical service person said there were problems associated with new software being not compatible with dryers in the last year and we needed a new control panel. I contacted Maytag again waiting the usual hour to get through on the phone. They agreed to replace the parts for free and ordered a control panel that arrived a week later. The technician installed both parts but they did not work. I contacted Maytag again and after waiting the required hour talked to a person who said she would contact the department who could arrange a replacement. They contacted me a few days later and said they would supply a replacement for $250. This was delivered a week or so later but they did not have a stacking kit and returned to the delivery company with the dryer. A week later they returned with the stacking kit but forgot the dryer. A week later they returned with both the dryer and stacking kit but the installer (always a different person) said he was too big to get in the space behind the dryer and that the venting supplied was wrong.I bought new venting from Home Depot and a new installer arrived a week later. He said the new venting was not necessary and in fact wrong and installed the dryer. It ran but foolishly I did not check to see if it heated and neither did the installers or if they did took off without letting me know that the dryer, like the one that was replaced did not heat. I discovered this a couple of days later when I tried to use it. I contacted Maytag and they setup an appointment for a new service technician to visit. I contacted Maytag again today hoping to get some explanation of what might happen next or some explanation. They had no idea but did inform me that they would not replace the new dryer but would start repairs again.

We purchased a Maytag washer and dryer from Lowes in the summer of 2016. The washer performed so so. Not a great machine. After only two years use, there is only my husband and myself, the transmission went out. The repairman said it would be cheaper to buy a new machine than repair it. Maytags 10-year warranty does not cover the transmission. We replaced the Maytag washer. I cant say anything good about Maytag.

I have always heard Maytag was one of the best so after replacing too many washers to count in 15 years, like Whirlpool and Kenmore, I decided to spend more for quality. I figured pay a few hundred more once rather than spending $400 for a cheaper one that only lasts 3 or 4 years. That choice seemed environmentally responsible and financially as well. However, I couldnt have been more wrong. In 2016 I purchased the Maytag Centennial top loader for $500. I really loved the size of the tub and the way it looked. I can fit a large comforter in it with plenty of room leftover. I also have no interest in a front loader after reading reviews. So I thought this was going to be great! Well it hasnt been. It has broken 3 times. The circuit board twice and now the bearings are going out in the motor. I fixed it the first two times but now Im done. Im done with Maytag, Aka Whirlpool. I think it will be a Speed Queen for me now. Im hoping it wont be a dud also because they are pricey! It actually scares me to spend that kind of money. I have really lost my faith in most companies nowadays. Customer service and quality has gone out the window. I think about how much this impacts the environment! Its terrible that appliances only last a few years before they end up in the landfill.

I have a Maytag washer and dryer. The washer is a top loader with a metal drum. You can hardly hear the washer while it is running, and I have had no problems whatsoever in the past six years of ownership.

Have had problems with the set since day one. Bought brand new from Home Depot. Got a great deal and now know why. Never cleaned the clothes properly, water marks on so many items, musty smelling regardless of how many times we cleaned it, horrible at removing stains, and finally not even 5 yo the motor stopped worked. The dryer has been repaired too and hasnt ever done a stellar job. Will never buy another Maytag product again!

Discovered that thousands of others are having problems with the control panel on their dishwasher. Mine is Model # MDB7749SBM2. Looks as if I should just junk this horrible product and buy a new one (another brand, of course). My biggest concern is that I purchased other Maytag products along with this dishwasher, ie, a refrigerator-freezer, a built-in stove top/oven and a microwave. I have had a service call on the fridge (water line), the oven (gas) will indicate a set temperature (400 degrees for example) sometimes it will only be abt 200 degrees via a portable thermometer... Sometimes it doesnt ignite at all (have to reset it 3 or 4 times, the microwave has issues with the digital readouts, and on and on and on.I have only had these appliances about two years (after warranty expired) when each unit started exhibiting problems. I paid $175 for the fridge repair and am now considering biting the bullet & replacing everything as MAYTAG/WHIRLPOOL apparently isnt going to take responsibility for any defect on ANY OF THEIR PRODUCTS! Im 75 years of age, retired and cannot afford the replacement route but it looks like I dont have a choice unless someone has a better suggestion. I dont have the skills or energy to attempt the repairs myself.

Washer leaves spots on clothes and massive knots in clothes. The serviceman has been here twice since we bought it and was told to use extra wash option and heavy load wash with fabric softener option as well, and to only use about one tablespoon of detergent. So much for the green option! Results, still washing clothes 2 or 3 times per load then into the dryer. Tried an experiment - washed a pair of my daughters white capris and then washed them at a friends house while water was saved in a separate tub. Holy crap, the dirt in the water. Do not buy this machine. Not even if it is offered to you for free.

The way the outlet line and pump are set up, the Maytag Bravos does not remove all water from the bottom leaving about 2-3 inches. Even following the monthly cleaning and care has not stopped the inside of the tub from producing MOLD. When I contact Maytag there was nothing they could do about this problem. At this point my washer is only a few years old. I attempted to clean it myself but the drum would not break free. My options are, deal with the smell of mold and mildew, Pay Maytag $250 to come out and clean it (this would need to be done every 1-2 years) or buy a new washer. NOTE: I paid about $550 for this one. I have run a few clean cycles with bleach, but I think at this point the mold has embedded itself into the plastic tub.

Bought a maytag dishwasher 04/12/2013...have been thru 2 control panels...Now installing a third...washer works great except for that!!! Model mdb8949sbb0.

We bought this washing machine 2 years ago and I was never really satisfied with how it cleaned the clothes. Darker pants would come out with white soap/water lines on them. The worst part, 2 years in, the washer basket seal failed and the bearings rusted. The washer sounds like a tornado every time it runs. I got a quote for $350 to repair it!

Purchased this dishwasher 3 1/2 yrs. ago. Control panel went out. We would have had to pay almost the cost of new one to replace the part! Maytag used to be reliable. The dishwasher we owned previously (not Maytag) was still working after 12 years!

If you dont want your sheets ripped, then DO NOT purchase this machine. All my sheets have been torn, and many items of clothing damaged beyond repair due to this machine. Also, the machine started rusting out the first year I bought it (see photo). The repair man said that I must be doing something wrong - of course, its the consumer and not the machine - ha! Maytag should have given all of us a huge credit to a different machine because they knew of these problems early on. Never again will I purchase a Maytag appliance.

I bought a Maytag microwave model mmv4203ds00 on May 2010. On 8-20-10, the microwave stopped working. It was serviced under warranty. However, on 10-31-11, the microwave stopped working again.

Control panel broken for a second time in 23 months: I purchased a Maytag dishwasher less than 2 years ago at Home Depot. 11 months later, the control panel went out. Specifically, the start/cancel buttons stopped working. A service tech called me under warranty; the control panel was shipped to me, and the tech fixed it. He also told me that they had had numerous problems with the control panels.13 months later, the control panel went out; specifically, the start/cancel buttons stopped working (sounds familiar). I can get nothing from Maytag, except a demand for service fees or sales pitches for extended warranties (at a price that was half of what the dishwasher cost new). They also offered me the free part as long as I pay the service call fees. I told them to just to ship me the part and that Id do it myself. Nope. I must pay the repairman. Now, theyll ship me the part if I pay for it, but they wont ship me the free part. It only comes with a service call.Maytag also told me that there were no reports of problems with the start/cancel button, an obvious lie with a quick internet search. The customer service rep sounded like she knew I was getting treated badly and kept using the word policy. Her supervisor was much more cocky and made sure I knew that I wasnt getting anything from her company.They make horrible products, attach what once was a good name, provide zero customer service, and lie to your customers. Great business practices. I will never purchase a Maytag product again.