After buying this dishwasher model MDB6759WWW3 in Jan. 2010, I fully expected it to work longer than it did! So far, the control panel has been replaced 5 times. The last time was Sept. 17, 2012 and already it is out again. I talked with Customer Service, since Georgia has a lemon law. After 4 times it is to be replaced.They had no record of the part that was replaced, just that a technician had come and repaired (by ordering the same part they had no knowledge of). This time they will either replace or instead of me calling, my lawyer will call. I will never buy another Maytag product and will encourage anyone else not to buy either. My daughter had the same experience with a refrigerator, a piece of junk they did nothing about. By the way, I have an extended warranty plan, which should not even be necessary!

I have a Maytag fridge/freezer model number MFF2557 10403089ER. The freezer keeps going out. The repairman replaced the computer board called a jazz board stating that the bulbs in the fridge part are too close to the board and the heat can cause the board to short out. He suggested switching bulbs to 25 watts which cannot be found for fridges. The freezer continues to go out and sometimes restarts itself or by flipping the breaker switch, brings it back. In the meantime, food is ruined. Yesterday, he put a new starter relay on the compressor stating that this series of fridge/ freezer has had a problem with the compressor and Maytag will not take responsibility for this. There is no recall at this time and we are waiting to see if this corrects the problem or if the freezer will continue to go out. Thank you for your help in this matter.

After the waranty ran out, oven failed to ignite. Called repairman who couldnt diagnose problem. Broiler works. Replaced some kind of wire & part for $350. Good for 6 months. Happening again. Paid a lot for this oven.

We purchased a Maytag dishwasher MBD7749AWM on 03/15/12 from Home Depot. The control panel went out on 01/24/12 under warranty. The unit was down approximately 2 weeks waiting for parts and a second service call. Just six months later (approximately 08/05/12), the control panel failed again. Thinking that a trusted American, iconic industry leader such as Maytag would stand behind their product, I called for what I thought would be a covered repair. I explained to a supervisor that their panels have not made it 1 year in service. She assured me there were no out of the ordinary problems with the panels for my model dishwasher in one breath, then stated they were out of parts and on backorder for three weeks. Now the truth comes out, further telling me that the unit is out of warranty and nothing can be done short of sending out a repairman, that I would be responsible for parts and service. After further discussion, she reluctantly agreed to send me the part for free if I arrange the installation and told me that it was very simple to install. When the part finally showed up on my doorstep with no paperwork, it was wrong. When I called and complained for waiting 3 weeks for the wrong part because there was no quality control in their parts and shipping department, all they could do was say sorry. They told me just to keep the part they sent and they would send the correct part. I begged that they ship the correct part overnight and they adamantly stated that was not an option. Maytag stipulates their process only allows ground shipping from FedEx per their contract. Knowing I had no other option, I agreed and waited for 5-day ground. The part showed up 13 days later and delivered by USPS. Apparently, I was lied to again and the left hand has no idea what the right hand is doing. Apparently, Maytag/Whirlpool have an inadequate and poorly trained quality control system in place and their manufacturing and electronic divisions are surly lacking a strong management team needed to go in and clean house. Instead, the whole mess they have contributed to continues to haunt Maytag has continued to be made to believe its okay to produce subpar products while continuing the complete demises of a once trusted American, iconic industry leader all while living on the Lorals of twenty years past.Whirlpool would do itself and this country a huge service by just letting this brand die and thrown on the heaps of scrap steel headed for China where maybe they can copy and fix what they were not capable of.

If you have a second floor laundry room, DO NOT, and I repeat, DO NOT acquire this washing machine!!! The Bravo MCT model washer is TOO loud (during spinning cycle), and for some reason, the clothes come out all tangled up. Some cycles are a waste of a cycle, and most cycles take a bit longer than my former washer. I miss the cycle choices I used to have on my former GE Profile washer (GE does not make that model anymore hence my changing brands). For the most part, clothes come out clean; thats why I give it a two-star rating instead of one. The dryer: Must dry every load in low heat so it doesnt come out extra crispy and wrinkled up. Although I generally have to run a second drying cycle, low heat does work great and the clothes come out ready to be folded/put away.

Maytag stove MGR7662WW - I purchased this stove about 4 years ago. Now, the stove will not light. I called in to Maytag only to be told I must pay a service fee or purchase a repair manual. It’s very strange. My old Kenmore lasted 22 years and here I thought Maytag would at least last 10 years less than half the life of my old stove, realizing products today are not what they used to be. Maytag, the dependability people, I guess that old Maytag commercial where the Maytag repairman is so bored claiming no one needs service for a Maytag product is really false advertising. Buy American products; I’m not really sure who is the current country who is home to the great Maytag corporation. I guess me and my wife will spend another $700 on another brand stove and try this process all over again, hopefully not again in approx 4 years.

I purchased a Maytag Centennial - HE Energy Star Washer from the local Home Depot on Guam.... Probably the worst clothes washer I ever purchased. I typically buy a Whirlpool brand for many of my appliances of which I have always been satisfied with the products. I understand that Whirlpool is now the new principal owners of Maytag. I bought the Maytag for my new second home which I have moved into as my primary residence. Great ads on TV that promote the Maytag product line but the product fails miserably in performance. From the day I purchased the washer, my wife, kids, and I visibly noticed the laundry doesnt get as clean as my previous washers, it takes longer to wash a load of laundry no matter what is the preferred setting, the irritating hum is deafening in my laundry room, now the washer has malfunctioned and doesnt cycle through properly, leaving the clothes either unwashed or wet... I do not know who is your servicing agent or center on Guam and I am debating to repair it or just dispose of it. I can tell you now... MAYTAG... NEVER AGAIN. Now I know why the Maytag Repairman is so lonely.... I wouldnt bother to repair it. I hope these issues do not filter down to your Whirlpool products. That Samsung is looking pretty attractive right now. I bought one of their dishwashers that is doing a pretty good job right now.... Guess what? There was a Maytag next to it that I didnt even look at.

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

Bravos washer is 4 years old. Started making an extreme amount of noise during the spin cycle. Had a repairman look at and showed me the bearings and area under the tub. $400 plus in damage due to bad bearings, rust to bottom of tub and surrounding area. Four years for a high-end washer is pretty bad. Needless to say, I will buy a new unit and would NEVER recommend a Maytag Bravos appliance.

Bought a refrigerator from Home Depot in November 2012 for a cost of $1,647.48. In August 2013 it stops making ice day 1, stops cooling & it is running nonstop, all lights on display go out day 2. Called Home Depot & was given another number to call, called that number was told someone would be out next day to look at it. Also told my warranty would expire in November & I needed to buy another warranty. Maytag customer service was very rude. If their product was any good why do I have to pay extra for another warranty. A $1,647.48 refrigerator that only lasts 9 months, REALLY!!! Do not purchase Maytag appliances if you dont want to lose your money. Shame on Home Depot for not standing behind their merchandise. If you have a problem while warranty is in effect, Home Depot should replace product.

Ive had this Maytag microwave for about 4 years and the magnetron had to be replaced. The keypad was replaced three times due to SE code shutting down unit which happened again. When I explained this to Maytag, they said it is out of warranty. I explained to them that the last keypad which was replaced was only 6 months old. They replied but the unit is out of warranty! I would never recommend Maytag or any affiliated companies to anyone.

Purchased the Maytag Aqualift self-cleaning oven and this feature doesnt work at all. I would have never have made this purchase if I knew the oven would not self clean. This technology with the water in the bottom to self clean is pathetic! I thought maybe it wasnt working and called for a repair since it was under warranty. The service man told me not to expect it to clean like a regular self-cleaning oven. But I complained that it did nothing at all! So now I have a self-cleaning oven that I have to clean myself!

BROKE AFTER 3 YRS. Purchase a new Maytag model: MVWC425BW1 top load washer and dryer after just 3yrs of use. It failed and to find out this is a common problem with these new open drum washers. The bearings go out. Be aware do not purchase them and they also do not wash your clothes good, clothes just stay in same position and you have to wash 2-3 extra washes. It was going to cost 350.00 plus to repair so I purchased Speed Queen that has good reviews. Tech said that top load open barrel washers have been a nightmare.

I purchased a Maytag Bravos washer almost three years ago and I have been unhappy with it the whole time. I have not had to have it repaired but its performance as far as actually washing clothes and being user friendly are terrible. My clothes do not come clean at all, the tub inside the washer collects any dirt or grass and I have to wipe it out. The inside of the washer smells terrible and I have to keep using fresheners (never had to use them before in 50 years). The cycle time is ridiculously long and only varies by a few minutes from a single item to a full load, I will never buy another HE washer.

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

It does not completely drain all water out of until. So unless your running the washer every day, you will end up with the most horrible smell coming from standing water. It is very irritating and so fowl smelling.

I have had my washer and dryer for about 5 years. After a couple of years, I noticed my washer would fill and stop. When I go to put clothes in the dryer, it’s still filled with water... very inconvenient! I have to open and close it and then it continues. The dial doesnt work properly! The delicate cycle hardly works... that started after about a year. It just freezes up and stops. I have to open and close it. It does not rinse right, leaves a film on dark clothes, and I have to rinse again; I do not over fill it either. Sometimes it does smell a little mildew.The dryer knob does not work properly. I set my setting and pull the knob out, and it doesnt come on. I have to do it several times or change the setting or put it on 30 minutes only... very frustrating! I never had these problems with my Kenmores! I wish I did not switch brands. These things should work properly. I realize washers and dryers dont last like they used to, but come on! They also cost so much more than they used to. I wont do this again. I will do more research as to what is a good product. Too bad!

I purchased a set of Bravos 4 months ago and what a bad purchase! I wish I would have researched here first. Being environmentally concerned, I bought it because it was supposed to be high efficiency and low water usage. My clothes are being destroyed by this machine. They come out in a massive tangled ball, covered in ink and animal hair (after a wash or two, they are completely embedded into the fibers). Sometimes there are dry spots after I take a load out of the washing machine. No idea how that could happen. It torn my favorite sweater, ripped sheets, bore a hole in a towel, ripped pillows, and DOESNT EVEN CLEAN! I have to wash my clothes twice MANY times to get the dirt out which doesnt bode well for energy efficiency. Im calling them again today to try and get them returned for advertising that they will save me money. Not even close! They are a rip off! I gave my 35 year old set away and wish I had it back! Maytag is JUNK!!!

BUYER BEWARE!!! We purchased a Maytag Dishwasher mdbh979sab1 on November 23, 2012. It is now July 31, 2014. One year and a half and the control panel is not working. Ive looked at estimates online of $450.00 for parts and labor. Customer service is no help at all, nothing they can do. She actually recommended KitchenAid for our next appliance. Maytag has become a terrible brand. We will never buy from them again. By the way, they also made our Jenn Air Oven, which turned itself on a number of times while we were away. 350 degrees. That was a total loss as well. We are filling up landfills with our Maytag/Whirlpool appliances and you will too.

Major issues with the Aqua Lift Range. Takes forever to preheat the oven, 15-20 minutes to reach 375 f- 400 f. Aqua clean cycle not efficient and does not clean at all. The stove top is impossible to select and keep the heat consistent. When adjusting the heat up or down when you slightly move the dial it overreacts. When moved the heat sways may more than selected. The fridge works well but the bottom drawer is way too flimsy and it wont last a long time as it will crack. This is our first purchase of Maytag appliances and it will be our last. Our old 10-year-old stove worked much better than this one. Sincerely, Russell ** & Linda **, e-mail= **

Maytag Centennial eco conserve clothes washer - I purchased a Maytag (non-agitating) washer, (model MVWC400XW) just about a year ago and I cant tell you how dissatisfied I am with this product. It does not clean the simplest of soil from garments. I have actually had clothes come out of the washer after a complete wash cycle, with dry clothes. They recommend putting soap in first, at the bottom of the washer and then load clothes; I have had clothes come out stained as a result the clothes sitting on top of the soap. I am requesting that I be able to return (have this washer picked up) from my home and replaced with a washer with an agitator or a compatible washer that actually washes clothes. I believe that this may qualify as a lemon with regards to California lemon laws.

A week after warranty expired, our 1 year old Maytag gas range (model# MGR7662WS 4) required new Direct Spark Ignitor (DSI) board. Knowing it was just beyond warranty, I inspected wiring first and found that the Bake connector on the DSI was loose, flopping around from a bad solder point on the board. Called Maytag and informed them of this manufacturers defect and all they offered was a $20 discount on a replacement part ($220 instead of $240). It worked with new part for 4 days, then something else went bad causing oven to spark, light, heat to less than 100 degrees, then shut down, then restart, then shut down, then restart, then stop doing anything. It has never worked correctly since then. How can a manufacturer of almost all domestic brands get away with such shoddy workmanship.. Taking advantage of defective or poor quality parts to sell more of the same when they fail and for an enormous markup? Where are the regulators who oversee monopolies and blatant scamming of American consumers?

We bought a refrigerator June 4th 2014. 6 month ago the freezer and refrigerator was getting warm. Had to call repair service, it was the blower! On Saturday 12/9/17 freezer wasnt freezing, then fridge was clicking on and off. Unplugged it, called repair service, it was the compressor. $800.00 to fix it, the same amount as when we purchased it. Repair service told us to call Maytag, he said, Maybe they will help you, would not help at all. Talked to Lori, all she said was warranty is up after a year, I then said, I think a refrigerator should last longer than 3 years! Will never buy anything Maytag again! Yes Maytag does SUCK!!!

Maytag dishwasher #MDB 9750AWQ - I am now on the fourth control panel and in less than one year, the present one is starting to fail. The third one failed in less than a year also! I have read the reports of others and apparently, this is not just my dishwasher. Maytag owes its customers a recall of this inferior machine.

Maytag Bravos XL Washer and Dryer. How exciting to get a new washer/dryer!! Im a savvy bargain and quality shopper, but I really messed up here. A little over a year ago, we moved from IL back to TX and I got to buy a new washer AND dryer at the same time (a rarity). I went and looked at SO many washers/dryers and decided on the Maytag Bravos XL because a friend said she loved hers. It had a deep water wash and bedding cycle (for our blankets, comforters, sleeping bags, etc), and I thought that I could throw that wayward sock in after I started the load (unlike our previous front load washer).Where do I begin with the complaints? (And Im NOT a complainer - never filled out a review in my life). This is what I sent to Maytag: 1) Im 55 tall and can barely reach the items at the bottom of the drum, along with the lid falling on my head when Im trying to do so. 2) Forget throwing in the wayward sock - it must finish the cycle its in before it will let you unlock the lid (Where did locked lids come from anyway? Is that how those missing socks are disappearing - escaping out of unlocked lids? What are we trying to keep in or who are we trying to keep out of the machine? Doors you lock - not washing machines! I dont get it!).3) Even the deep water/bedding wash cycle does not do the job. Using the exact recommended measurement of HE liquid soap does not get the items clean. What a chore to take something out and have white detergent lines all over it and have to wipe it down with a wet cloth. Sure, I could then do a rinse and spin cycle, but since it doesnt add enough water, it doesnt come out much better. The machine senses by weight how much water to use. I am positive that every energy efficient machine is now programmed to add exactly 4 cups of water per load (regardless if its a comforter or one pair of jeans).4) Supposedly, we are saving so much water usage, but energy efficient is a misnomer - it takes me twice as long to do laundry now. The time factors are ridiculous. There are no quick cycles on this machine. If I have a load of delicate tops that just need a quick wash and rinse before I hang them out (I was not out baling hay in them, so its not like they are filthy dirty. In Texas, its the sweat that you are trying to eliminate), the least amount of time I can find on a cycle is 45 minutes. I might as well hand wash them all and be done in 5 minutes. But, that was the point of the washing machine - to do the work for me! And forget the deep water wash cycle of 58 minutes, plus the added rinse and spin cycle (to try and remove the white soap line). Its now taken one and one-half hours to try and clean/refresh a barely soiled comforter.5) The spin cycle is SO efficient, that I have items come out totally dry many times in certain spots. Im washing a comforter right now and I can guarantee you that when I remove it from the washer, there will be an entire section that looks like it never even got wet. Im no engineer, but after watching through the see-through lid, the agitation is not working well enough to get to every section.6) I havent seen a soap bubble or suds yet. You are told to use such a small amount of detergent, Im not sure how anything actually gets clean. The clothes are sprinkled with water, agitated a small amount, spun until they are almost dry and voila - the same dirty clothes come out! 7) The dryer has now ruined 2 of my bras as the hooks get caught in the mesh panel at the back. It literally melted part of the bra! I tried hooking them together before I threw them in there, but now have to put them in a lingerie bag to keep them from being mauled and mutilated. I have NEVER in 37 years of marriage and washing had that happen before.8) I literally could not get my dryer to turn on and a repairman had to come out to the house to show me the amount of pressure I had to use in one finger to start the dryer. I had almost taken a hammer to it before he arrived. Can you imagine pressing the start button on anything - the dishwasher, a hair dryer, a TV remote control, and it not turning on? And all because you pressed too hard or too light? This computer age and electronic panels are killing me! 9) The dryer has the same locking system as the washing machine. So, if you didnt see the wayward sock on the floor or between the two units until after you pushed (lightly, of course) the start button, you have to stop the unit before you can open the door to throw the sock in.I didnt mean to write a novel (about a washer and dryer, no less)! But, I feel better and hope that I have saved one woman from making the same mistake I did. Read those reviews AND believe them. And by the way, my friend who recommended the Bravos XL to me looked at mine and said Thats NOT my washer and dryer. Evidently, mine was the new and improved version! So much for that claim!

We purchased a Bravo HE washer about a year ago after our old Maytag finally died after 17 years. Our new one is more quiet, does a good job with less water although the cycle times are a bit longer.

I have had two Maytag washing machines in the past. Both lasted 20 years. Three years ago I purchased my first Maytag front loader washer and dryer. The washer is terrible. Although I clean it regularly plus spend money buying Affresh tablets and leave both the door and the soap dispenser open, the washer smells and builds up tons of mold. Cleaning out the heavy mold in the soap dispenser area is almost impossible. I spray bleach in there and then try to stick my arm into the back where most of the mold accumulates. Cant really get it all. Also, there is a problem with the softener dispenser. It gunks up and gets clogged. Had to keep pouring hot water and vinegar into it. Contacted customer service who was no help - they simply wrote to clean the machine. Huh? The dryer turns sheets into a tight roll with the inside not drying.

Bought a Maytag HD top load washing 11/4/17. Within the first month the machine began to make a loud squealing noise during the wash cycle. A repairman came out 2 times before finally replacing the gearbox and tub. Within the last month or so the problem began again, another repairman came out twice, and once again, had to replace the gearbox and tub. When he left I ran a load and the machine sounded like a war was occurring inside of it. Very loud banging and grinding... heck I was wishing for just the squealing back! Maytag refuses to replace the machine and just keeps sending out repair people. The Maytag name once stood for quality but that was long ago.

Purchased a Maytag Bravos washer in 2009. Was told it was water efficient and electric efficient also. Spin cycle twisted my clothes in a knot and left white blotchy doors on my dark clothes, had to rewash my clothes again!!! Then started making a horrendous noise that could be heard from one end of the house to the other, like it was going to explode at any given time. Called technician, paid $75 and said it was bearings and that it would probably did the same noise again even with fixing it, that Id be wasting my money!! Worth getting rid of it!! I just hate it!! I will never buy another Maytag again.

Maytag Bravo washer and dryer delivered 2 days ago.My complaint is with the washer. I didnt know it was HE and that it requires special detergent! I didnt know the lid locks! I didnt know when I push the hot water button, the machine mixes in cold water! Complicated, delicate machine and not user-friendly. I dont expect the washer to last long.

Model# MVWB850WQ0, Serial# CY4070329, Type 580-02. Bought this Commercial Technology washer 2-1/2 years ago thinking the commercial model would be heavy duty. It was only heavy on the wallet. The washer started to emit a loud roaring sound two weeks ago that never happened before. It happens on spin cycle. We cant even have a normal conversation in the house. After reading similar problems and outrageous cost to repair, Im leaning to look for a replacement without the Maytag label. My 10+ year old Sears Kenmore didnt have any problems. My mistake was to replace it with a more efficient washer. I guess New+Efficient doesnt equal long lasting for Maytag. You would think a major manufacturer would put in heavy duty bearings in a washing machine. Heck, maybe the bearings are heavy duty but design shortens bearing life. Enough time spent on Maytag. Stay away!

We have had this refrigerator (Maytag Side By Side Refrigerator with Ice Dispenser 27 CU) for 5 years this month and have already had to have it serviced once and now the ice dispenser just went out. I wish there was a brand out there that did not have problems and when problems occur, you do not get the runaround to get them fixed!

This is an awful product. I bought this product from Best Buy at the beginning of August 2018, and can no longer return it because it’s past their 14 day return policy. This washer does not wash clothes well. No matter what setting it’s on, clothes come out looking dirtier than prior to washing. Maytag should do what is right and refund customers for this worthless purchase.

I bought my Bravos XL 3 years ago after having older model Maytags since the 1980s. My mother also runs a laundromat and SWEARS by Maytag. To say Im disappointed in this purchase is an understatement!!! They have never washed the same as the older models. They twist the clothes horribly! Now Im having issues with all of my dark clothes getting grease spots on them with no apparent cause. I use HE detergent and softener (recommended amounts only) and clean the washer religiously, including the detergent, bleach and softener cups. I DETEST these machines. Also, the dryer never dries unless I run it for 2 cycles, regardless of what setting it is on. Waste of money and definitely not energy efficient when it comes to my water and electric bill, nor time efficient for me since clothes either come out still dirty or with new stains. After this purchase, I would NEVER buy Maytag again!!!!!!

Maytag Gemini - This is a double oven which I purchased in 2010. 2 days ago Apr 13, 2015, the outside glass in the bottom oven simply exploded. The oven was in use at the time. It blew the side brackets off and glass was spread into my dining room as well as a mess in the kitchen. Maytag was supposed to send repairman today. Have waited all day and finally called repair company. They knew nothing of the repair and supposedly will contact Maytag and call me tomorrow. We will see. In the meantime has anyone else had this problem?

We purchased a new Maytag washer and dryer from Home Depot; a couple months later the dryer started to rattle so we contacted Maytag and they sent a service tech out who stated this was normal as the dryer was settling and parts are not as tight as they are when new. This was a garbage response and he was asked to leave. I contact Maytag again, told them of the problem and the tech response and they offered to send another tech out except I would have to pay for the service call since they already sent someone out. I sent them an audio file of the rattle, no reply. Eventually Home Depot ended up replacing the dryer as Maytag refused to help me despite it being in the warranty period.

Front load washer unit does not respond to control inputs. I have called Maytag service and support. One can find a repair or maintenance manual. Im in a smaller market so there is limited service. Maytag service and online support is terrible. Maytag stores are fronts for independent service companies. Its probably okay, but misleading. Everyone wants to order the main controller board. It would be good to have a maintenance manual.

I have been on the chatline with Maytag customer service for two days, trying to enforce my warranty, which expires next week. My washer flooded my kitchen over the weekend, and I contacted Maytag to schedule the repair under the warranty. First, the woman, Aisha, looked up my registration, and confirmed that I was who I said I was, that my address and phone number had not changed, and told me that according to the records, the washer was purchased on 2/7/2011. Whats the problem? First, they wanted the model and serial numbers. I realized that this is important information in determining what machine needs what repairs, except there was not one sticker anywhere on my washer! Aisha said that the technician would not perform the repair, if the manufacturer did not install the model information properly on the machine. As if I had any control over the placement, or lack thereof, of proper ID for the washer. This was followed by a request for proof of purchase. I explained that I moved, and misplaced it, but I would have it emailed to me from the original purchaser. I was told that unless she could verify the proof of purchase, and the date of purchase, she could not schedule the repair under the warranty. This is despite the fact that not 5 minutes ago, she had just read this information from her computer! I asked her why would I register someone elses washer under my name and address? She didnt care. I told her I would have the receipt emailed the next day, and she stated that regardless of the date I requested, and scheduled the repair, if the actual repair took place after the expiration date of the warranty, it still would not be covered! I told her that makes no sense. I have no control over your scheduling issues. If you cant honor the warranty if the repair is made after the expiration date, then I need a date prior to that. I am entitled to the terms of the warranty, and intend to use them. Aisha said again that, without proper proof of purchase and purchase date, without proper tags on the washer, and if the repair takes after the expiration date, it would not be covered. I disconnected from her, and reconnected with another rep, who told me that some of the information Aisha gave was incorrect. I can schedule the repair, get the receipt and email it, or submit it through the chat, and regardless of when the repair was actually done, the warranty would still be honored. This person couldnt be sure what effect the lack of proper tags would have on that. My third re-entry into the chat was no better. I located a copy of the receipt in my email, and contacted the chat again. An almost amazing thing happened! This woman again confirmed all of the information Aisha recited last night, and was prepared to schedule the repair, without even asking about proof of purchase. This woman, Jennifer, was willing to schedule the repair, verify that it would be covered under the warranty, even if it was after the expiration date, because I had called and arranged the appointment before the expiration date, and she was willing to have the missing manufacture tags replaced. I had to ask her three times to review the email, and confirm that I had the correct receipt for the technician. I asked if the technician in the course of repairing the washer, had to remove the drainage hose, could he either replace it with a longer one, or add an extension, because according to Lowes at the time of installation, the hose they installed was supplied by the manufacturer, not them. Jennifer stated that since he was only there to repair the leak, and installation is not covered under the warranty, I would have to pay for him to replace the wrong hose, with the correct hose myself, even if he removes it! I told her that she needed to ensure that the technician absolutely did not remove the drainage hose from the back of the washer during his repair, because if he removes a part that is obviously the wrong part, and then replaces the wrong part after his repair, I would file a complaint every single place I possibly could. Why would a repair technician remove a part, determine that it is the wrong part, and then put it back! That is like a mechanic repairing the axle of a car, and discovering the brakes are bad, but since he is only there to repair the axle, he replaces the bad brakes after fixing the axle! He was going to be able to replace the missing manufacturer tags, though! This entire process took at least 3 hours and two days. To date, Maytag/Whirlpool is absolutely the worst company I have had to deal with, right after Sears, and ahead of AT&T. The consequences are that so far, Maytag refuses to have the technician replace the wrong hose with the correct hose, if he removes it in the course of repairing my washer.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

I dont know anything about the Maytag washers and dryers but have a Maytag washer and dryer. And I just recently bought a house that the owner is leaving both the washer/dryer, and both are Neptunes. I have an older set of Maytag washer/dryer and they are about 20 yrs old. They are both top load and I had one repair where a water line had a small leak and the service man came and fixed it and havent had any problems since. So I came on Maytags site to see how good these are, but from what I read, I think I will give the set of Neptunes away and just keep my old set as I am told them will last a good 35 or more years. They are heavy duty and large capacity. Thank you for letting me comment on your washers and dryers.

I had a Maytag washing machine replaced under warranty back in 2011 via Maytags Extended Service Plan. This took me several months to get done because of back and forth issues with Maytag not wanting to honor the replacement. Executive Support had to get involved after I wrote a complaint on this site. When they replaced this, they sent me forms to extend my warranty, which I did. They never changed the model or serial number so Ive been paying for 2 years now for an extended warranty on a machine I do not own.The new washer broke and I called in for service on 11/18/13. Active Appliance was sent out, said it was an easy fix but they needed to order a part. On 11/20/13 they contacted me to tell me I needed to speak to Maytag because my Model/Serial didnt match with my warranty records. I double-checked these and called Maytag Extended Service and was told that I would need to speak to sales at 866-730-6094. I spoke to someone named Lindsey there who told me that I would need to send a letter in to cancel my policy and request a refund for the 2 years Id been paying for a non-existent unit and that they could start a new policy for me and get a service order in without issue. My call was disconnected during this and when I called back, I was told to call back in the morning to get back to Lindsey because the office was closing and they couldnt do callbacks.I called back on 11/21/13 and spoke to Sam who verified that the letter was needed to cancel and refund but that I would have to pay for the repair to the washer myself and theyd tack on the cost of the new warranty onto that bill so Id be covered AFTER THE FACT. Because the unit wasnt covered under warranty, Id have to cover the costs myself and it had been MY responsibility, not theirs, to make sure that the correct model/serial was on the coverage.Maytag sent me the forms and I would expect them to have added the new information on it...not send me forms with my original washing machine information. Especially as this had been escalated to Executive Support and the person I dealt with there had gone over everything to make sure it all got handled in a satisfactory matter. So for now, Im waiting for a callback from the original rep, Lindsey, but Maytag tends to Stonewall and not return calls so Im dreading how long this entire process is going to take and cost.

I totally understand the technology age. We need to move forward as a country and keep up with modern technology. But somebody please tell me why this means companies have the right to not stand by their products? Why do consumers have to pay the price for bad products and companies leaving us high & dry? My husband & I were excited to redo our kitchen. We bought all new appliances in November 2011 - all Maytag. In December 2012 (13 months after we bought them), we started having issues with the oven. The oven would not maintain the proper temperature. We called a service man in January 2013. He deduced it was the computer board so he replaced it. Cost to us - $350 (including service call and labor). Now, less than 2 months later, the same problem. Maytag, Whirlpool, Kenmore - whatever company you are now - rest assured, you will not survive if you continue to produce shoddy products and refuse to back them up. The service man is to stop by again tomorrow. I refuse to keep plugging money into a product only 15 months old. I will not buy another product from you again. I just hope the dishwasher, microwave and fridge make it to at least 5 years old. Isnt this funny? My grandma has a Maytag washer & dryer - 35 years old. You sure cant say positive things about your products today. Good luck to your future - youll need it.

Maytag washer Purchased December 2016. Washer is very slow: runs 1 hour plus. Wash takes a VERY long time. Small load only. Heavy loads go to Laundromat. Maytag does not clean clothes, always MUSTY smelling. Cycle OFTEN does not drain tub And forced to use Drain, Spin cycle to drain tub. Wrinkle cycle ties clothes in knots. Using AFRESH to clean tub makes no difference in foul odor. One service call, error codes found, computer reset. Repairman said that the MACHINE WORKS AS DESIGNED. Repairman said that any tiny bit of debris can cause washer to clog and fail to drain. At best clothes always wet, slow to dry. My old Whirlpool washed any sized load. Clothes always clean and fresh. I used laundry only when we had power outage. LIKELY WILL PUT THIS ON THE CURB. I DO NOT RECOMMEND THIS MACHINE.

On December 22, 2013 I purchased a Maytag front loading washer Model # MHWEE201YW00 from The Home Depot. On July 28 the bearing failed and greased my clothes and rendered the washer unusable. On August 1st I contacted the Maytag Customer Service Line; the wait for contact was approximately 20 minutes, not a very good answer time and unfortunately the best I would receive during this process. Despite the wait, I received good response and had a service call set up for Wednesday August 6th.On Wednesday August 6th, a service technician from Quaker City Appliances took a look at our washer and determined that the bearings had failed and that the entire drum assembly would need to be replaced. He stated that anytime the bearings fail this soon, it typically means that the bearings weren’t pressed properly or the drum wasn’t tightened enough and that he would order the parts as soon as he got back to the office.On Friday August 8th, a representative from Quaker City Appliances called and notified us that the part was no longer available and instructed my wife to call Whirlpool Customer Service and give them this number **, to coordinate a replacement washer. I called later that afternoon and spent over an hour waiting and was transferred between departments. The first representative was very cordial and professional; the second who I believe was from the Tech-line was anything but. In my career I have held responsibility for customer service and while there are many golden rules, one of the most important was never to tell the customer “I can’t”, well Cheyenne (I believe that was her name) couldn’t help me with anything and clearly told me so. She explained that my problem was referred to the Trade Partners and I needed to call back to Quaker City Appliances on Monday.On Monday August 11th, I called Quaker City Appliances, who promptly informed me that the matter was turned over to Whirlpool and I need to contact them as there was nothing else that could be done. Later that day I called back to customer service, again waiting between two representatives at least an hour. I was informed that my matter was with the Trade Partners and that I will need to wait one to two days for a phone call. A phone call that never came…..Yesterday August 14th, I contacted Whirlpool customer service, again waiting over twenty-five minutes for the first contact, and then was eventually handed over to the tech line and another wait. Eventually, I spoke to a very pleasant representative who gave me the Trade Partner number and transferred me, unfortunately I was disconnected. I called back and found out that the office closed at 5:00. Today I called the Trade Partner line (1-800-874-4698) at about 3:30 and after 40 minutes I have given up and decided to write this letter. All I want is a functioning washing machine.

The only time one can get enough water into the washer to actually get ALL the items wet (or even damp) is to put it on BULKY sheets or HAND wash settings. That is true for any size load whether it be 1 item or 10 items. I prefer being able to get ALL the water I need first, then put in the clothes, then soap, but thats not allowed. First soap, then items, then a bit of water only after you close the lid. They like to say that the spinout dries them which is why they arent damp - but that is a lie when you can smell and see the dirt. I want my OLD STYLE back!

My fiancee and I purchased a Maytag washing machine from our local Sears. We got it home and it worked fine, but after the first month it wasnt switching over from cycle to cycle. We called Sears and they stated that they didnt provide service to the washing machines, so we would have to call Maytag. We called Maytag and they sent servicemen from B & B Appliance to our home. We were told that they needed to order a piece and would be back at another time to fix the washing machine. They came back and said it was fixed. I went to start a load of laundry the following morning and the basement flooded. The hose had become dislodged when they were working on it. To add insult to injury, the washing machine was still broken. I called Maytag to request a different service company come to our home. Maytag said that they couldnt send a different company. They also couldnt replace our still broken washing machine and they could not accept a return. At this point we are out an almost $800 for the washing machine, over $5000 (which we have submitted to insurance) for the damage to our home, and almost $600 for a WORKING washing machine that was a different brand. We will never use Maytag ever again.

We lost our home in a tornado in 2005 and had to buy all new appliances. So, I bought a Maytag Neptune front load washer and dryer. It was my 1st ever. I will never buy another Maytag appliance again. Just at the end of the 5th year going into the 6th year, the bearings started to go. So, I checked with the place where we bought it and was told how expensive it would be to fix. It was anywhere between $500.00 and $700.00. Well, thats crazy. I therefore e-mailed Maytag numerous times and was thanked for my complaint. But they offered no help with this matter. If they dont back their stuff at all, why would I want to buy their stuff? They could have at least offered to help with it. There are only 2 people living in this house and there is no excuse why that washer should start failing already. If I thought it was worth it, I would load it up and drop it off at a Maytag store and leave it there. It still runs. But it makes an awful noise and we are just waiting for it to crap out. I am going to try to sell it for as much as I can get out of it, hopefully before it completely stops. Maybe some fix-it guy would want it. Well tell him whats wrong and they can fix it and sell it to some other poor person. I lost my job in January. Therefore, I cant afford that much to fix it. So, I will now have to try to find something used, because Maytag does not back their stuff. I would rate this machine lower if I could, but that wasnt an option.

We have had washer/dryer Bravo Series and been nothing but horror stories. Washer bounces all over room to point hoses come out and flooded my laundry room and foyer and garage. It takes over 1hour 45 minutes to do loads sheets which is 2 sheets 2 pillowcases. The repair man told me that takes that long due to MY sheets are dirty. I have been married 46 years and never heard that ever!!! The dryer is just as bad, takes over hour and half to dry sheets and towels almost 2 hours to dry. DO NOT BUY MAYTAG ANYTHING. The person who said needed hurricane straps to hold washer is something I agree with. Just a horror.

Its a shame that I bought into the Maytag equals quality and customer service falsehood. Same problem as the others on this site and undoubtedly thousands of other consumers that bought a similar refrigerator freezer combo only to discover puddles in front of the unit and a 1 thick slab of ice under the freezer drawer. I contacted Maytag parts and when I described the issue he transferred me to warranty. The warranty department acknowledged this was a known problem and they would supply the part, no charge for the part but I would have to pay the serviceman to install it. They would not however, send the part to me to install. The unit is out of warranty, of course it develop the problem until right after the warranty expired. I plan to examine the drip pan and figure out how to improve on the design myself. I will not replace any appliances with Maytag, Whirlpool, Kenmore, or any other major appliances from this group of companies... Beware!

I bought a Maytag dishwasher (Model: MDBH949AWS2) from Home Depot on 07 April 11 and it died 24 August 11. I called Maytag to set up an appointment for repair. The repair person showed up and stated that the control panel needed to be replaced. Apparently, if moisture gets into the panel it shorts it out. One would think that when designing an appliance that utilizes water and creates steam, it would be sealed. Anyway, the repairman explained that because the dishwasher was in a residential program, the warranty was null and void. I wish that someone would have explained this before I purchased it. I went online to AppliancePartsPro.com and ordered the part for $100.75 including the shipping cost. Then, I went back online to look up how to install the panel. The repair person said that they are charging $133.00 for the part and $129.00 to install. A small star tip screwdriver and 15 minutes was all it took to fix. From what I have read, this will not be the last control panel but, at least, I know how to fix it. Another thing that I know is that Maytag is off my list of future appliance purchases regardless of where Im using them.

I had a Maytag washer and dryer for over 25 years. I loved them so I replaced them with the Maytag name. They are not the same company as far as pride and product workmanship.From the get go it always had a dirty odor to the tub, as though the clothes had been left in it for days. I was told to just run through a cycle with bleach, but nothing. There is no lint collector and after about 8 years of using this washer, the old lint is in the bottom of my washer after every wash. Now, I have to deal with the thing coming to a screeching stop, not spinning out the water after the wash cycle. Sometimes it’s full of water and other times some water drained, but the clothes are full of water and not spun out.Now tonight, I went downstairs and found water on the floor, it’s leaking. My question is to call and get it repaired or not waste my money and go buy another brand. I may go with the latter.I purchased a fridge and dryer at Home Depot a few years ago. I wanted to stay away from Maytag name. I purchased another name only to find out it is part of Maytag. No wonder I’m having trouble with my fridge, making ghost-like howling sounds so loud it consumes the entire house. So annoying. Stay away from Maytag. They are not the same reliable, take-pride-in-work company.

We purchased our Maytag Bravo XL in 2012. Over the past year and a half we noticed the inside of the top lid is rusting as well as the bleach dispenser area. I called Maytag about the lid and they said there was nothing they can do and that we could buy a new lid replacement. Really??? My parents had only Maytag in their home for over 50 years with little to no repairs needed ever! We were a family of five back then. Because my parents always bought Maytag products so did we. This is the first time in 40 years that I have ever seen this happen! I was hoping for a recall for these issues but dont find any online. The washer and dryer were not cheap and purchased from a reputable retailer.

Last week I noticed that my freezer motor had a build up of frost. I melted it with a hair dryer. 2 days later there was a layer of frozen water on the bottom of my freezer as well as a layer of water on the first shelf in the fridge area. There is no way to access the drainage tube. I thought that the coils needed to be cleaned. That was not successful either since the coils run horizontal and only the front section can be vacuumed. Today, again the freezer motor area is frosted and layer of ice on bottom and the motor is making a terrible noise. How disappointing for a less than 2 year old fridge.

I purchased my Maytag Refrigerator in Feb 2013. It is model MFF2558VEW7. It has the French doors w/ freezer at the bottom. This past week, I lost everything in the freezer. I call the Home Depot where I purchased it and they said that I have to call Maytag. I did and they sent a repairman out. It needed a compressor. After only 8 months, the compressor goes out? Why should this fridge be repaired and I not be given a new one? With all the problems with the Maytag, there needs to be one big class action filed. I asked for a loaner because it would take up to five work days for them to order the part. The answer was, We do not provide loaners.

Maytag is the worst dryer ever purchased. We bought it in 2019 and the heating element broke. When I contacted Maytag directly, they said, nothing they could do. Really?? A major part was defected and there was nothing they could do! Its very sad when a major company that you purchased from shuts you down with a defected piece in their dryer and they chose not to help out the consumer. Shameful! I will NEVER purchase another product from them again...

We bought a Maytag Bravos three and a half years ago. We always tried to follow instructions for the machine. Only used he detergent, used the affresh, tried not to overload the machine etc. Had to call a repairman. Our washing machine started leaking water at the bottom. Hoping that it is only a three machine it would be fixable. Bad news the repairs would be over $600.00. It needs a new tub seal and bearings. For a THREE YEAR OLD washing machine! The repairman and I had quite a talk about appliances. He said they just dont make them to last anymore and the companies such as Whirlpool, Maytag, etc. do on purpose and they get away with it. Stay away from Maytag Bravos. It is a worthless piece of crap. It will not last long. Now we have a three year old washing machine that does NOT work right. Something has to be done in this country to come down hard on the companies that make appliances. I would NOT recommend this piece of crap of a washing machine.

So I get the matching set washer and dryer when I moved into my new house. I thought I was getting a nice set. I paid around $1600 for them with the sale they had going on. From day one the washer wouldnt get a full size comforter wet on the bulky cycle or heavy duty cycle. I even tried the extra rinse cycle on both as well. I would have stop it mid wash and rotate the comforter. Clothes wouldnt settle sometimes and would leave the top dry and bottom soaking wet. In the first year the lid latch started going bad. So sometimes you would go back to realize the load hadnt even started. Clothes dont get clean no matter what setting you use. It is the worst purchase Ive ever made. The dryer was ok until its almost second year. It just stopped drying it seemed. I cleaned EVERYTHING! No effect. It takes 3 full cycles at minimum to dry clothes. I cant understand why these machines arent pulled from the market or recalled because they are junk.

Oven door glass shatters after 6 years of having this oven and the company refuses to cover it. According to them it is not a safety concern. It is actually designed to shatter this way. Wow, thats comforting. Should be 0 stars not 1 star.

Maytag needs to step up and admit that they have a design flaw in this dishwasher. The problem is that just a week or two after the warranty is out, it just stops working. Sometimes when you walk by it, it just turns on. No way to turn it off. Nothing works on the control panel. From what Ive seen on the internet, everybody is having the same problem. Its the control panel. It costs 180 dollars to fix, but it only lasts another year and you have the same problem. Ill have to say that when it works, it does a superb job. It just wont keep working.

Horrible washing machine. Cannot get clothes clean. It simply does not supply enough water to wash. Have tried everything. I want my money back. How do you start a class action lawsuit. Thousands of people are dissatisfied also.

Purchased a Maytag Bravos top load washer and dryer in May of 2011. We had our other Maytag washer and dryer for 14 years, and they were working fine when we sold them. We saved a year for a new one. We spent $1,700.00 for them both. We assumed they would last as long as our old ones. Been buying Maytag our whole lives. Besides the clothes not getting cleaned. Besides the washer smelling, even after we clean it regularly with the product proposed. Besides it not working on the normal function. Besides it shredding our clothes if you put it on the highest spin speed. It started to make a very loud noise. Like an airplane taking off. Called a friend of ours that use to have an appliance store in Fenton, Michigan for decades. He said it was the bearings and that You have to replace the whole tub. A $300-$400 fix. And that it would do the same thing again in a short period of time. He said that they are junk.We would be better off buying a new one. He said, The ONLY one you can buy now that will last like they use to is Speed Queen. I had never heard of them. They start at about $750. But they are worth it. He said that they dont make any washers to last more than 3-4 years anymore. We will NEVER buy Maytag again. And Sears wouldnt give us the time of day. Each time we called and asked to be switched over to the recall department, we just got a busy signal, then a fax machine noise. We have shopped at Sears for years. Boy, loyalty doesnt mean anything in this day and age. Im sure Speed Queen will be happy to help us out. DO NOT buy any Maytag products. There should be a class action suit against them for this. There are thousands of us that got ripped off. I cant tell you how upset my husband and I are about this. We are retired, and on a fixed income, and I am disabled. The stress this has caused cannot be put into words.

This Maytag Dryer (Model #MEDP575GWO) was delivered January 29th and the paint on top of the dryer is bubbling and peeling. I haven’t even had the unit 4 months yet and they tell me the warranty for “cosmetic” reasons is on 30 days. This is completely unacceptable and I will sue them if necessary. I am in utter disbelief.

I also purchased a Maytag refrigerator model #MBR1953YES3 at Home Depot less than 2 yrs. ago. A year had not passed and I noticed the freezer starting to freeze up. Water started to leak from the bottom freezer. My husband had to break chunks of ice that clogged the drain but still, it continues to freeze. We hired a certified technician to clean the drain but a few days later, a puddle of water appeared all over our kitchen. Now we have a towel to stop the water from coming under the refrigerator. I thought when I was buying a Maytag, I was buying the best. I now know that, it was the biggest mistake. I will think twice before ever considering buying a Maytag again.

I purchased the most expensive stackable set available. After 3 years the Maytag Front Load Washer is dead. Wont turn on or receive electricity. It stopped in the middle of a cycle so I have an entire load locked inside. A repair person came out and confirmed $600-$1,400 to replace computer electronics. Right on the front of the machine, there is a shiny tag displaying 10-year Warranty. I live chatted with Maytag. Only the drum and some other ridiculous part is covered. She told me to call the 800 number to speak with a customer rep. After trying 2 times and being put on hold for over a half hour, I hung up. I WILL NEVER BUY A MAYTAG AGAIN!

A lot of the reviews contain complaints about the Bravos XL MCT top load washer. We purchased one in December, 2015, and so far have not had any problems. We had a 3 yr old Whirlpool side loading washer that we just gave away, as it never got enough water to even dampen a comforter or quilt. This machine works very well, in spite of lower level of water. I was pleasantly surprised when I could see the water level with the first load! The controls are not as intuitive as other machines; e.g. spin only requires you to select Rinse/Spin cycle, and THEN turn OFF extra rinse. Perhaps the proper way is to have a Spin-Only cycle, and then tell the user to click the extra rinse ON. We do probably 1 load a day. Water bill has not been significantly higher than when we had the Whirlpool that hardly used any water. Today, though, a heavy quilt (it WAS distributed evenly around the impeller) was put on Bedding so the water level would be a bit higher to ensure the entire quilt was wet. Fine so far. However, during the Spin Cycle, the unbalance became so violent that the washer stopped for a few seconds and then went BACK to the Rinse cycle. It did this several times before we realized that the time remaining had not gone down in over 30 minutes. My guess was that the sensor believed that maybe some additional water with another Rinse cycle MIGHT even out the load. It didnt. I finally stopped the machine, redistributed the quilt and then ran the Rinse/Spin cycle, choosing NOT to do the extra rinse. All came out fine. There was NOTHING in the manual indicating that this might be needed, except for the instructions to Spin only. If I have any other problems, I will send here.

My Maytag over the range microwave has given me nothing but troubles since my purchase. The turntable off feature never worked, and now the side control panel is barely hanging on because of broken plastic connectors. The handle is now broken in half. I will never purchase another Maytag product. Buyer beware.

Product number MMV4205DS. Beautiful, felt solid. Right away when we would put in a time to cook and hit start, the thing would say Open Close Door. First we thought it was moisture, and we would wipe the seal, then lifting the door a little helped. A month might go by and we would repeat this process. I did a little research and found the microwave is known for this. After the warranty was up, it got worse. My husband put a little screwdriver in the door clamp. The plastic guard that held the door shut fell behind the opening. Mulling over whether to call for repairs or buy a new one, we decided the latter. I am buying another one just like it, because the holes in the wall will match for an easy swap and it matches my suite. This time I took out the 3 year warranty, which I will hold Maytag responsible for any more problems. They say if they come and fix it 4 times in a year they will declare it a lemon and replace. I figure this will work in my favor because the microwave lasts a year!

Thanks for the other reviews about the control panel problems... I too have the same issue with the short circuit. My Maytag dishwasher mdb7749sam1 was installed in January 2013. I spent an hour on the phone and the chat... HERES THE SOLUTION: When I told them the machine started in the middle of the night on its own, it became a safety issue. I have all the same problems as everyone else, flashing lights, the washer does not properly respond to the input from the control panel... I was told that even though it was out of warranty, as a gesture of goodwill Maytag is sending out an authorized repair service to fix whatever is wrong at no cost to me at all... Tells me that there really is an underlying issue. Anyway best of luck to anyone else in the same boat. I rated them as a 3 - not happy that this machine failed and I wont buy another, but they seemed to jump on fixing it...

I bought the largest Maytag top load washer. From day 1 clothes come out with laundry detergent left all over them. I have to take a washcloth and wash off every piece of clothing coming out of the washer. Had a technician come out. He said he gets this complaint every day. His suggestion, put less clothes in and use less detergent. This washer is programmed to use minimal water and it just doesn’t have enough water to clean all the detergent off. So, I bought the biggest washer to wash bigger loads and now you are telling me that just doesn’t work.Spoke with Maytag customer service. They said very rudely if there is no problem found when the technician came out, there is nothing they will do. She told me it was user error. My dryer also stopped working. Sometimes it would turn on, sometimes not. The technician said the lint screen error code came up. He would try to get Maytag to replace the whole board but usually they don’t do that unless the whole board has a problem. Called Maytag the next day. The technician documented he fixed a connection problem and closed the ticket. What???? So, now I guess I need to schedule another service visit. Very unhappy with 5 month old appliances. Paid $1700 for the pair, you expect quality products.

I purchased my microwave in 2012 and have had to have numerous repairs, mostly with the open/close door switch error. It is now 2018 and I see that the same problem is still occurring! Maytag obviously hasn’t read or doesn’t care that this problem has existed for years and they choose to do nothing about it. This past week when I had the microwave running, the beep went off indicating the popcorn was done but when I opened the door the microwave was STILL running! I thought it was a fluke but it happened again. Tonight the open/close door error once again appeared on the display. Having already had this repaired to the tune of over $150, not to mention the danger of a microwave running when the door is open, I called a mayday on the Maytag! I decided enough is enough and went out and purchased a new microwave... Obviously NOT a Maytag. The dangerous inoperable Maytag microwave is in the garage waiting for trash pickup.

I had this microwave less than a year. The control panel went out and Maytag fixed it. Now a year and a half later, the same thing happened. This product was almost $400 at the time we purchased it. I have had better luck with $40 microwaves.

We purchased our double free standing gas range about 6 years ago. Our top oven went out about 4 years after purchase. We purchased the extended warranty from Sears and it was fixed at no charge. About a year later, the top oven would not work again. We called Sears, our warranty was up so it would be a repair that we would have to pay for. We decided to go with the Maytag repair service since it is a Maytag appliance and we had to pay anyway. The repairman came in and said that the top box that holds the electronic in it had fried wires and it would have to be replaced. So for $480, he could replace it. It was more than likely caused by a power surge. I just read that this also coincidentally happened to someone else so I find this cause to ask more questions. I also note that the top of the oven behind the burners where there is some sort of vent gets extremely hot (I accidentally touched it and had a blister the next day) when the oven is being operated. This is directly under the box that holds the electronic components. I would think that may have something to do with the wires frying since it is that hot directly below the panel. Could this be a defect in the building of the stove? Has anyone else had this instance beside the one person that I read about on your website?

Maytag AquaLift Oven #YMER8880BW - The aqualift technology does not clean the oven. It is sorely inadequate. I bought Maytag because of its reputation. This range should be recalled as should all their ranges with this useless technology. Buyers BEWARE! Do not purchase any range from Maytag which advertises Aqua Lift technology. This purchase has soured your reputation Maytag. I also purchased a fridge with the stove. I will NEVER buy a Maytag product again. I also would like to ask frustrated and disenchanted readers how they are getting their ovens cleaned. What product(s) can be used. Maytag - complete FAIL!!

I bought a Maytag dishwasher, model MDB8551AWB, in 2007 and have kept purchasing maintenance agreements. From January 2011 to March 2012, I have had to have Maytag send out a repairman to replace the control panel five times. This is absolutely ridiculous, and the inconvenience. Plus the repairmen are surprised Maytag keeps on repairing this dishwasher and not replacing it. More the $2000 has been put into this dishwasher since January 2011. When calling Maytag, I was informed that the problem would have to be the same which it has been but on the same contract for it to be classified as a lemon. Well, it has now been four times. I will never purchase another Maytag.

MHW60X - I experienced a problem in May of 2015, and the repairman told me it was the master board, and he has seen this many times. He said that the MCU board goes out after 3.0 - 3.5 years!! This is exactly how old my machine was! The cost to repair this was almost what the machine cost, and this is unacceptable. I have had Maytag washers my entire adult life, and my prior one lasted approximately 20 years, but after this I am not sure I will consider another one in the future. To have a major part burn out soon after the warranty expires should not happen. I contacted customer service to find out the experience and reported problems on this model, but could not obtain any information, other than they have received calls about this model. I asked Maytag to reimburse me for the part - at a minimum, and they refused stating it was out of warranty and they could do nothing. Apparently they do not care about their reputation anymore, which is sad, since they used to be so well regarded!

I have had this washer 4 years...I bought this washer in May 2016. It makes 3 very loud noise as it moves into its next mode/cycle. Found out this is normal. IF, it is close to your living room, IT is loud.. I called again, saw that it was not filling up. 1/5/2017.. IT will NOT fill up to wash my clothes properly, clothes were still dry!!! Came out, (they sent a company near my area), said everything is right. I have tried, by sending messages, many times to get them to check. No one seems to care. The machine allows water to go out the bottom, rather than fill in the machine. I watched it myself. THERE should be a recall on this machine, definitely, something is sooo wrong.. I NOW have to put it on BULKY SHEETS full time, to get my wash clean.. NO energy savings there... BUT my clothes are finally clean!! Seriously, something is wrong...

I am not complaining at all about my dealer. I am complaining that I also am like the many others with the French door fridge/freezer. The bottom of the freezer freezes up and water pours all over the floor. I thought that Maytag was a good appliance, but also had problems with the pump and drain on my washer. Both of these are only 2 1/2 years old.

My daughter purchased this washer and matching dryer as a set from Lowes about 4 years ago. It was one of the few with an agitator and that is what she wanted. After using the washer for the first time she was very disappointed to find that the shortest cycle took over an hour and that the locking lid feature couldnt be bypassed. A few weeks ago the washer began gushing water onto the floor which flooded the basement below. She had purchased an extended warranty which was due to expire the following week.She called Lowes and scheduled a repairman. He finally came 2 weeks later and used the Internet to help him diagnose the problem!!! We could have done that. He decided that the control panel was only allowing the agitator to turn in one direction during the wash cycle. So essentially it was spinning a tub full of clothes and water causing lots of water to overflow the tub onto the floor. Needless-to-say he had to order a part and cant return for over 2 weeks to install it. IF this is even the problem! He also said he couldnt disable the locking lid feature! If my daughter had been able to open the lid when the problem started she would have known more about it.We are thankful her machine was under warranty but she will have been without a machine for almost 2 months when and if it is fixed. This is completely unsatisfactory for a gently used 4 year old washer. The dryer takes forever to dry also. If you are buying Maytag based on how long your grandmothers machine lasted, you will be disappointed! This washer caused so much damage we had to file a homeowners insurance claim!

We purchased a Maytag Bravos washer & dryer in September 2012 and 2 1/2 years later March 2015, no heat. We called a repairman and he said heat element went out. When researching this problem online I was shocked how many people had the same problem as we have. It cost over $300 to fix and I am concerned that it will just break again and again after reading these reviews. I think that a class action lawsuit may be needed so that this unfortunate situation does not continue to happen to other consumers.

My refrigerator temperature control panel started flashing lights and the ice maker flap started opening and closing over and over. I checked online and there are numerous model #s doing the same thing, most all contacted Maytag, some were fixed for no charge. Some were not even though they admitted there was a defect in the electronic control panel. I was one of the ones they refused to fix because they said it was an older model but they fixed a 2006 model, a defective part is a defective part no matter the age especially if they know and admit there is a problem with the control panel.I cant understand why they wont take care of their problem, so now I have to spend over $300.00 to fix a problem that they made in manufacturing, that is not an outrageous amount, thank goodness, but I just dont understand why they wont stand behind their product when they can fix out for probably half that cost to take care of their problem. I didnt make the refrigerator, they did.

I spent over $600 dollars on a Maytag Bravo 300 series. The washer has cost me over $300 to fix the latch and 2 months later, it will not spin. I would recommend to anyone not to buy a Maytag product! Garbage! I had a standard Kenmore washer that lasted over 10 years without a problem, paid $300 and still sold it for $100. The funny part is that I sold it to my brother who still uses it regularly and has not had any problems. So what is money worth? Your call.

I purchased my 2nd Maytag Neptune washer in 2005 to replace an early Neptune that was complete junk. This one worked OK until this year when it began to make awful noises. After research, I decided it was the bearings that failed. I took the unit apart to get to the bearings and found out the entire outer tub must be replaced not just the bearings, at a cost of $515. What lousy engineering, the bearings dont come out of the housing. No wonder Maytag repairmen are so bored. There is nothing to fix, you just buy a new washer. I wont buy Maytag this time.

I had a tub failure on my washer Whirlpool Duet, which I bought brand new and it lasted 12 years with no problems. The dryer is still in use at my sons house. However, this failure lead me on a search for a set to replace the duet. I did some research and found the Maytag 6.2 Cu. Ft top loader and huge Dryer to match. The set was not cheap and it did have high marks for a great washer. So, I bought them both and had them delivered on 12/30/16. I have read all the owners manual and watched YouTube videos to see how to use this machine with all its pretty lights and sounds. I will concede that the machines look great, very impressive in my laundry room. I would bet it would even be a plus when I go to sell the house.THAT is all the nice stuff I can say. The machine does not clean clothes and I have done all the settings. I have changed laundry detergents, and even tried to add a little more water with a bucket at the start of the wash. (Saw that one on YouTube.) REALLY. That did not work, nor should I have to do that to get it to clean well. The answer seems to be, set the machine on FULL tub of water. So, I tried that for a couple of times and found that the clothes just float around and since they do not touch the Wear Plate they dont get clean. My wife (yes, I am a man that does most of the laundry) said she hates the washer and I was an idiot for buying this expensive piece of metal that does nothing but take up space and leaves spots on your clothes. Have you heard the term Happy Wife-Happy Life. Well not so much for me now.Spending money even $2,500.00 on a washer and dryer seems a little crazy. But I had the extra money and I have always wanted a MAYTAG. These guys know how to make a washer. Boy was I wrong, this machine must be an embarrassment to Maytag. I know I am really shocked that you would sell this machine as top of the line. I am not sure what Maytag will do, but I thought I would give you a chance to make this right. I have attached pictures of the machines installed and pictures of the model number plates. I have faith that Maytag will step up. My wife said this was a waste of time. The ball is in your court Maytag. (Come on Maytag let me win this one.) - Just a man and his dirty clothes.

I have had this refrigerator for a few years and never have had a problem. It keeps food uniformly cold, and is frost free. While appearance is attractive, it doesnt look like a $3,000 refrigerator. However, black pebbled-surface exterior is easy to clean and scratch-resistant. Plastic and glass interior fittings also have held up very well. I originally thought it would be too small because I was buying it to fit a certain space in the kitchen. But it has turned out to be just the right size because there is no wasted space inside. I bought this at Home Depot on sale for about $400.00 and it has turned out to be an excellent buy. Delivery was on time, efficient, and people were polite and helpful. Refrigerator was ready to be used about 15 minutes after delivery arrived. I have found Maytag appliances to be extremely reliable and made to last. They have never disappointed me. I will continue to buy them. I highly recommend it.

Oven worked ok for a year and went under right day after warranty expired. I called factory-approved repair people in Brooklyn but was told repair would cost more than buy new oven. I contacted factory but got no help either.

We purchased this Maytag about ten years ago. We had an old brown one that had to be 25 yrs old and still going. This piece of junk has had two compressors; the ice machine hasnt worked in a year, and now it just went out again (third time weve lost hundreds in food)!!!! About the same time we bought a Woods freezer on the cheap, this freezer sits in the laundry room crap piled on it and around it and never have had a problem. Maytag = $2500.00 boat anchor.

We bought a Maytag French Door 21 cu. ft. refrigerator in 2008. 2010, 3 repairs later, the ice machine went out, we went back to ice trays. Now the compressor died. The old ad of bored Maytag repairmen cause they never need repairs is bogus.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in 2014. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within warranty. Then another valve got stuck about a year ago and the third one got stuck about a month ago. I am going to replace these two valves now. My friend, who is helping me replace, has similar gas range. He also needs to replace a valve. His range is about a year old.

My Maytag refrigerator, model number mff2557heb, serial number 10375839gv, was purchased in 5/2005. Two weeks ago, this refrigerator stopped working. I called the Maytag technician and then right away came to my house and find out it is the compressor that needs to be replaced. He told me to search if it is under warranty. I searched in the internet Maytag compressor warranty and I found it and then called the Maytag representative. I told them I have found in their website that compressor of this Maytag is covered for 10 years but labor is not included. Then they asked me to fax it. I faxed the copy on 6/20 and they responded on 6/22. He said they received the copy and he said, Yes, it is covered for 10 years but you will shoulder the labor. So to make the story short, this Maytag representative scheduled Friday, 6/29 for the Maytag technician to fix my refrigerator. My husband did not go to work yesterday, 6/29, Friday, so he will be home for this Maytag tech. Maytag tech came at about 2pm yesterday and when he confirmed that it is the compressor that is the problem, he asked for the warranty paper. And when my husband present the proof, the copy of their warranty coverage that came from the Maytag website, he refused to work with my refrigerator because he said the one in the internet is not valid. It is really upsetting because I faxed the copy of it to them on 6/20/12 and they honored it. Thats why they arranged the technician to come to my house and then my husband did not work for them to work with our refrigerator and then asking me $79 for just saying that it is not covered by the warranty. I even gave them the model number and the serial number of the refrigerator so they can verify if it is covered. He said yes 10 years warranty on the compressor. In fact, two employees that I have spoken to both agreed that it is 10 years coverage except for the supervisor named Rachel. Her employees agreed to 10 years based on the paper that I have faxed them and it came from their website and they dont want to honor it after they sent the technician to my house. Thank you so much for your time and for reading about my grievances against Maytag employees.

The washer is designed to use low amounts of water. The top is glass so you can watch what is or is not happening. The manual states there should be clothes above the water after filling. However after the wash cycle with a full or even half full washer, there is still some dry clothes above the water. As a result the clothes are not washed until the rinse cycle. I called Maytag and a repair tech came out to fix it. His solution was to trick the sensors by dumping a pail of water on top of the dry clothes before starting the washer. The sensors think there are more clothes than there really is. Will never buy another Maytag or Whirlpool product again.

less than 2 yrs old and has completely failed to operate. We have been patient with this model. It does roll the clothes to point they are wrapped around and among each other and must be pulled apart before placing in dryer. The wash cycle now takes more than 45 minutes, It fails to spin the load often. Now, it has failed to the point it will not operate with or without any clothes in it.

A contractor purchased the Maytag MDB7609AWW2 dishwasher about two years ago. Sometimes it will start a load, but most times it will not. The light for high temp, heated dry and sanitize work, but the heavy, normal, light indicators will not light up. Im faced with either replacing the control board or control electronics. I was told Maytag is a quality product. I have not abused the product. The last dishwasher that I had lasted 10 years. I only purchased this one because of a remodel. I will most likely replace the control board since thats the defective part. It doesnt give me a good feeling about replacing the part since it’s obviously a defective part. I will consult Consumer Reports before purchasing another dishwasher.

Maytag dishwasher 5/3/2010 model MDB6709AWQ1. 12/20, 2015 it is dead, $69.00 service call. Failed user interface and main PCB parts estimate with labor $449.46. Called Maytag Co. We would pay the labor $139.00. MAYBE they pay the parts.

Like everyone else Im calling corporate. Mr Fettig he should be in hall of shame after these complaints with their defective product. My fridge leaking, ice maker broken, water everywhere and eight inches of ice. I wonder if he owns a Maytag himself? Oh well after a while he might have a flood on his floor. This should be recalled just like my first model in 2001 that was a fire hazard. I had to go to the top then and I will now also. We should be protected from buying garbage while he makes 4 million a year.

Maytag 2000 series front load washer - f you are looking for a front load washer DO NOT buy a Maytag! I purchased a new front load washer dryer set late 2013 and have regretted to washer ever since. Continual electrical problems, door gasket needed replaced almost immediately AND the worst part is that it has ruined over $1000 worth of clothing due to it trapping cloth between the drum and door and wearing holes in them. No matter how I load the clothes or sort them it continues. I have contacted Maytag and was told I have no recourse as the warranty is over. I was very disappointed because I have had Maytag products in the past and had no problems. Please, think twice before buying this washer! It will cost much more than just the ticket price!!!

Bravos gas dryer - three issues in three years. Same issue twice, clothes are not drying. Now I have company coming and have to deal with his issue. The blower motor went. So, I have paid for a new dryer in repairs already. The washer is making such a loud noise when it goes into spin cycle that you have to turn the volume up to the highest level on the TV and it is still tough to hear. It’s unbelievably in the horrible quality. Make the product and parts in the USA and stop buying junk from China and Mexico. This is good American money that is flushed down the toilet with Maytag as well as your reputation. Fix your quality control and do the right thing!

I purchased the Top Loading Maytag Washer and have had nothing but an awful experience with this washer. The dark clothes come out with soap on them. I then need to take a wet towel to wipe out the soap stains. I have had a repairman in 2 times so far and there is nothing he can do to fix it. Maytag said I must wash all the towels with towels, all jeans with jeans, roll clothes into a loose ball before putting in machine, use the extra rinse cycle and the longest wash cycle and do not load clothes more than 5-6 inches high in the tub plus 7 other things I must do to get a clean load and none of those things have worked yet. If the salesperson would have told me all this, I never would have purchased a Maytag and nor should you!

Maytag fridges, obsolete in less than 3 years. TWICE! My last Maytag fridge dies at about 2.5 years. I called up customer service. It was a compressor not repairable. This was an expensive fridge. Reluctantly we bought another one as the space could only accommodate a Maytag. Again less than 3 years old, the ice maker is shot and the plastic inserts are all falling apart. This time Ill renovate my kitchen for that extra 2 inches to accommodate a different brand.

I bought the Bravos glass top washer. It was always loud. I have a friend who had a cheaper model and his was loud too. My washer barely lasted two years before tearing up. It cost $85 to tell me it would be over $500 to fix it. I paid over $600 so it wasn’t worth fixing. Lid lock went out and gear went bad.

Bought this Maytag XL washer and dryer in September 2012. In January 2014, the washer stopped working. Service guy came out and said the electronics went out. Then in May 2014, the dryer died. The dryer door latch broke. Would not stay shut. 2 days later, the heating element went out. Again, the service man came out. This service man said that this model is subject to break downs. This Maytag is a piece of junk. I went out and bought a Whirlpool, which I had before. I would never buy a Maytag again. I paid over 2000.00 for this Maytag and it is the worst washer and dryer I have ever had. Apparently, the Maytag repairman needs to get his butt busy. I have the Maytag now on my sunporch, waiting for the junk man to come and get it.