My original GE dishwasher that came with our house finally crapped out after about 8 years of use in 2007. Bought a Maytag from Home Depot for around $400. Dont remember the model number. It worked okay but then in the middle of 2010 we got a letter in the mail saying our machine was being recalled because the heating element might catch fire (!!!). The recall gave us the option of getting it fixed or getting a $150 rebate. We chose the rebate option so we trashed this dishwasher and went back to Home Depot to buy another one.We found a very nice Maytag with the stainless steel tub and the racks with the lifetime warranty against corrosion (which was good because our previous Maytag had started to leave rust on our dishes because the plastic on the tips of the rack tines was starting to come off), model #MDBA979AWB1, serial #FY2501885. The one we found was a no-box display model but it had all the accessories with it and still had the factory warranty. We got it for just over $300 and with our rebate applied we were out the door for under $200 including tax. I installed it myself and didnt have any issues for quite some time. My wife and I were both very happy with how clean the dishes got!Now, last night the dishwasher wouldnt start. I checked it out this morning, made sure it had power and was able to get some lights on the control panel to light up but still couldnt get it to start. Looks like Ive been victimized by the control board as most of these complaints have said. I guess I should consider us lucky since ours seems to have lasted longer than the average 18 months to 2 years. Will be contacting Maytag and Home Depot to see what they can do but after reading all these negative reviews Im not hopeful.

Purchased washer March 2017 and had to get it repaired twice by the end of 2018. The top loader even with agitator does not clean clothes very well. The repairman said not to fill the washer above halfway so I can only wash about 4 pair of my husbands heavy soiled work jeans. I won’t buy another Maytag.

Turned the oven on, and it failed to light. A little while later, it started leaking gas into the house. Im lucky the house didnt explode!

All my kitchen appliances are from Maytag, however I would highly recommend buying the extended warranty for any appliance you buy. Maytag is not helpful to customers when it comes to repairs. They will recommend you their authorized companies which here in Colorado Springs are the one with the worse review and already knowing the the repair will cost more than the cost of a new one. You will have to be available 5 hours of your day and spend $110 for a guy to come to your house and tell you that the repair will cost more than a new one. Oh and if your microwave is a 2.0 CU like mine you will have to pay $300 plus in double labor because your microwave will require two people to take it down from the kitchen cabinet.

I positively HATE the new BravosXL Maytag washer, which has no decent agitator. It is ruining my clothes, as it spins with little water and leaves soap residue all over the clothes. Additionally it puts large, long wrinkles in my knits, especially disfiguring slacks. Maytag must have known how rough and ruinous this washer was on knits BEFORE selling it to an unsuspecting public! I want my money back in order to purchase an old-style, well-functioning agitator washing machine.A class-action suit should be brought against Maytag. There was no way to know before buying and using that this machine is horrible!!!

I have a Maytag purchased about a year ago. My old Maytag lasted 16 years. The salesman told us that they are now built to last 8 years. It’s pretty noisy, so much so that I have to close the door to the utility room. I guess it gets the clothes clean but it used very little water. Fortunately my model has an agitator but nothing like the old kind. After looking at many models, I feel this was the best choice for the value. It is top loading which I like.

Dishwasher Model MDB7749SBM1 - When I returned home from work today, I noticed the cancel drain button was on and the unit was continuing to try and drain but the dishes were not clean and the cascade pod was still inside the unit unused. I then proceeded to run another cycle to clean the dishes and what happened next simply amazed me. I pressed the jet clean button, tough scrub and 2 hour delay button and thought I was all set but the start/resume button would not engage or light up at all and subsequently the cancel/drain button lit up and the unit started draining. Now the control lock and start/resume button just flashes intermittently and wont disengage. I purchased my unit along with several other new Maytag appliances when I renovated my kitchen. I guess the microwave, stove and refrigerator is next -- unit are only 29 months old. Any assistance will be greatly appreciated. Im in deep ish I guess.

Purchased the Maytag Bravos washer from Home Depot in August of 2011. Today it caught on fire (Sept, 2014). Had problems with it from the start. Some of the issues include the washing machine constantly getting off balance even with small loads, not completely draining the water from clothes resulting in having to run additional spin and drain cycles, and a bad odor coming from the water that stays on the clothes (we even called a plumber thinking it was something with our plumbing). Well today was the best. I started a small load (one twin flat sheet and a pillow case) and about 10 minutes later I smelled a weird burning odor coming from the laundry room. When I opened the door to the room it was filled with smoke. The washer was the only appliance running, otherwise I would have assumed the dryer was the source of the smoke. When I opened the lid to the washer, smoke started pouring out from around the inside drum of the washer. It smelled like burned rubber and ash. Needless to say, I doubt this washer is worth repairing. We actually have had repairs on it previously (twice in the first year) and its just a piece of junk. Glad I was home when the washer caught on fire. I hate to think what would have happened if I had not been able to unplug it and it continued burning. Do Not Buy This Brand. Definitely do not run this washing machine unless you are home to monitor it. Maytag Bravos is a fire risk!!!

My Maytag microwave caught fire and burned our cabinets and wall. We had just arrived home from vacation and our fire alarm went off. No one was using the microwave at the time, it just caught fire. We put the fire out with the extinguisher and called the fire department. Our wall and cabinet are charred and our house smells of burnt plastic and is covered with the residue from the extinguisher. Maytag sent a technician to investigate the microwave and, just like the fire department, determined that the cause was internal within the microwave. A Maytag agent called us and offered us 10% off a new microwave and 15% when we told them our house had been damaged plus we wouldnt have to pay tax. Theyd even deliver and install it for free. According to my estimation, thats probably less than $50. They told me that the microwave had no value and tried to make it seem as though they were being generous. Its an 11 year old microwave but there should be some kind of warning that they spontaneously combust after a certain period of time. If the microwave had just stopped working because of age, that would have been understandable and I would have just purchased another the next day. Instead these microwaves just self-destruct and Maytag seems to be ok with that. I was not surprised that they had a 1.5 star review when I came here. I have 4 kids, ages 2-9, who wouldnt sleep that night because they were afraid of the microwave.

Replaced a Maytag Bravos xl washer and dryer in 2015. First year was fine but almost right after the warranty period, the spinning cycle was loud. You cant even have a conversation near the washer. I put up with it after calling the repair department. Because I was told that it will cost as much to repair than buy a new washer. Now the washer does not drain when a small amount of cloth are in the washer. Dont buy this washer and dryer. Maytag is not as good as it once claim.

MVWC200BW0 - Washer starts to fill and then drains before completing the fill cycle. Contacted Maytag through the live chat on their website (cant talk to a real person on phone). Since my one year warranty had been expired 12 days I was told to contact a certified repair person. They offered no help in solving my problem. Told nothing they could do, warranty had expired. Maytag will never get my business again. Now I know why the Maytag repairman is so lonely, people have quit buying Maytags.

Just so everyone knows, Maytag, Whirlpool, and Amana washers are all made by the same company and almost all of the internal parts are the same. The differences are mostly cosmetic, its just a way to sell more of the same thing to different classes of people. Just like Chrysler sells Chrysler, Plymouth and Dodge, they all had the same engines, transmissions and electrical systems, just different looks to appeal to different people. I found this out the hard way after purchasing an Amana front loader washer and dryer that broke down on me every other week for a year. I got tired of it and purchased the Maytag 2000 series. This set also breaks down on a regular basis! This is when I found out from the repair company that services these machines that all I did by getting rid of the Amana set and buying the Maytag set was buy a different looking set. Now I am really pissed. This company works for Whirlpool warranty servicing Whirlpool, Amana and Maytag as well as other major brands. All same machines inside the repair man said! Look into it, research it online and call whirlpool for yourselves as I did. You will find it to be true. So if you hate your Maytag, Whirlpool or Amana front loader washer or dryer, research and buy from a different company or you will buy the same old problems again and again.

The engineering of all these new machines are totally useless. Bring back the old tech. They DRY wash, NO WATER, they take forever to finish, wasting energy, clothing not cleaned. They are very noisy, doing nothing. Time to recall all of these units. They are totally useless.

Our brand new Maytag dishwasher model number MDB87749SBM2 was professionally installed on 7/31/2013. In fall of 2015 my control panel started acting up. I was unable to select certain wash cycles. The problem would come and go. By January 2016 my lock button would freeze and I was unable to unlock or select any wash cycles. By February 2016 my control panel went out completely. It wont turn on, not a single light. It is fried.When Googling the issue I found that we are 1 of MANY with faulty control panels not only on our particular model but on many Maytag dishwashers. They all seem to have the same problem, right around to 2-3 year old mark. One would think dishwashers would last, like before. A dishwasher shouldnt need to be replaced or need a major repair so soon. The one our new dishwasher replaced was 12 years old and was working just fine. We just wanted to upgrade to stainless steel. Wow what an upgrade haha! Maytag should be recalling these control panels. Their name is no longer a trusted name in our home.

Just like most of the other consumers, the control panel on my three year old Maytag dishwasher (MDB 6701AWW3) has failed for the fourth time. The cost of repairs and extended warranties has now far surpassed the original cost of the machine, which was $400. Today when I called Maytags customer service, I was offered another extended warranty for $316.05 for one year. I suggested that there was a defect in design but was assured that this was probably due to use of the machine. I guess if I left it as an unused space filler, it would last forever. They commiserated with my frustration. Never again will I purchase this brand.

We bought a Maytag Gemini double oven in June 2007. It has been a problem from day one. It arrived with a damaged door. They reordered and replaced it. Through the next few months, I became very discouraged with the oven. I bake a good bit and was always used to an oven with fairly accurate temperature. This oven will not reach or sometimes just wont maintain a steady temperature. After a couple of service calls, I gave up. I now raise the temperature setting about 50-75 degrees higher that the recipe requires. Naturally, I dont always get the best results. However, that isnt the thing that really bothers me. These ovens have three ignitors. About every six months, one breaks. The cost is over $200.00 each time. The ovens/broiler are highly unreliable. After mixing up something or on an important holiday, one may find that the oven wont light. Theres no warning! It is simply gone. I will never again buy a Maytag! I called Maytag and questioned them about the lemon law. I was told that the same piece had to break three times in one year. That is crazy, when the entire thing doesnt and has never worked well.

I purchase my Maytag Bravos washer from Sears in May 2011. In February of 2014, I started to get the UL message, meaning unbalanced load. I would re distribute the clothes and sometimes that did the trick and others not so much. Now every load comes up UL. I tried putting the machine on the drain and spin cycle to at least get the clothes a little bit drier but the UL message still appears and the clothes are still soaking wet. I lifted the washer up and there is an oil/grease type spin pattern under the washing machine. I called Maytag today (which is now Whirlpool I guess) as the washer has a 10 year warranty on the drum and motor. I was told a service call is $129. When I mentioned that I had Googled the product and saw many reviews with the same exact problem, she stated the Bravos has no common complaints. From what Ive read, it seems to me it would be more cost effective to go out and buy a new washing machine and it obviously wont be another Maytag or Whirlpool.

We bought this dishwasher on 7/8/2013 which is my wifes birthday and boy was that a mistake in many ways! I had 5 service calls on my Maytag Dishwasher MDB7749SBM1 before it went out of warranty. It has issues with the ribbon cable and controller and the control lights are like a disco on the keypad. Now it gets so hot I cant touch the door when its running. So I have had to turn off the power and go get a new dishwasher next weekend which WILL NOT be a Maytag!

Purchase a Maytag Bravo XL Washer Model MVWB850YWO from a major Home Improvement store in January 2012 with a 4 year service plan. Since this time I had to replace a motor and 4 (that is right 4) control panels. Although I am covered under a protection plan, the cost of laundry services and an outage of 2 weeks for each event is very costly. This time I call Maytag for support on their product. Looking for someone to say that there is something wrong with this machine. I want to hear that their product should not perform like this. I was told from a supervisor in these words that Mrs. we only care about the machine the 1st year. After that you are on your own. When did Customer Service lose the service part? When did companies stop caring about their products they produce? I never heard I am sorry youre having trouble or even a recommendation. A machine this new should not have 4 control panels replaced. This is the reason no one wants to buy a Made in the USA product anymore because we know the employees working there do not care about keeping customer relations.

We purchased a Maytag from Lowes about 3 years ago. The spin function quit working properly last Feb 19. We paid $350 to have parts replaced thinking it was a fluke and we would be set for a long time to come. Well, last week the same thing happened... not even a year later. Lowes doesnt care and Maytag doesnt care. They want you to spend more to get a warranty to get you to 5 years... well as far as I am concerned that is not good enough. An appliance should last 10-15 years. This Maytag was to replace a Whirlpool that caught all of our clothes in the agitator fins, so after a short period of dealing with that we paid out for a Maytag without an agitator. So in the span of 6 years... we had about $1,500 of dissatisfaction. I believe our repair guy said they the companies are one and the same. Selling junk ought to be illegal.

I bought a Maytag washer and dryer 3 months ago. The Bravo XL is simply a piece of crap. No agitation and clothes come out as dirty as they went in. It also leaves soap stains on all the clothes by since it doesnt agitate enough. Nothing is wrong with the unit, just a horrible engineering piece of crap. Ive been in manufacturing for 30 years and cant even imagine how a company like this can design, test and still sell such a piece of crap. You put a shirt on the top of the load when starting and its still there at the end of all the cycles. Just absolutely horrible. Do NOT purchase any washer without the old time center agitator post. Horrible....

We have had our washing machine for about 6 months, we got the F3 E6 error code. After doing some research, we found out that the control module was what we needed to replace. My husband and I called both Maytag and Lowe’s, (the store we purchased the washer from). We have been given the runaround. After talking with several managers in the Lowe’s warranty department, we were told that we had to contact Maytag directly about that particular problem. Okay, no big deal. We called and every single time we were put on hold for at least 30 minutes before we were hung up on. Not once did we even get to speak to a person. If we don’t get a response and our problem doesn’t get fixed, I will be going to the Better Business Bureau.

Purchased a Maytag refrigerator on 08/15/13 model #M1TXEGMYQ01. Started having cold problems 06/15/15, called company. 1 yr warranty expired 08/15/14,had to replace a 22-month ref on 07/15/15. Prior I owned a Hotpoint that lasted for 17 yrs and the last one was a GE that lasted for 18 years.

As many other reviewers have mentioned there is a defective control panel in the Maytag Dishwasher series MDB 7749. I too purchased this model at Home Depot and did not buy the extended warranty. The serviceman indicated that this model is known for its defect yet Whirlpool who owns Maytag does not have it on its recall list. I wrote to the President twice in Sept. 2017 without the courtesy of a response and now learn that he retired effective Oct.1. Is there no-one to answer his emails or is it more likely they really dont care. Sears just dropped them and who knows where their new president will lead this company. Be aware that this model dishwasher is defective and they wont replace the control panel. Too bad as once Maytag before Whirlpool bought them out, was a good and honorable company.

I bought this washing machine approximately two and a half years ago. I replaced the agitating wash plate three times. After several months, the wash plate will start free spinning from the gear and will spin like a top. It has to be replaced at $140.00 plus the service call. When it was working, it doesnt clean the clothes well. I contacted Maytag numerous times about this problem and they basically gave me a tough luck answer. I just went purchased a old style machine with a tall agitator that will clean like its suppose to. Its a shame Maytag has no compassion to try and compensate customers for the expenses. I also contacted Whirlpool which took over Maytag. My rating is a negative five.

When I remolded my kitchen almost four years ago, I purchased four Maytag appliances. There was a recall on my dishwasher that was successfully fixed; the heating coil could have caused a fire. The next appliance to go was my refrigerator with a bottom freezer: the freezer section went. Thank goodness I purchased a policy which covered the repair that had to be done twice--twice I lost food. I was compensated by the insurance company for $200.00 for the cost of food lost. Just before Christmas my microwave stopped heating. The turntable works, the timer works, but it will not heat the food and makes a loud noise. The glass top on my stove is getting marred even though I clean it every time something spills. I keep my appliances in immaculate condition and they look like new. I thought when I purchased Maytag I was buying reliable appliances. Their ad that states that the Maytag repairman is lonesome because he has no work is a lot of bull. Each appliance has had problems. Where is consumer protection? Appliances should not breakdown after a couple of years. We should not have to buy insurance policies that are expensive to protect appliances that should last at least ten years without problems. Someone needs to step in and help the consumer. I didnt call Maytag regarding the microwave as I was told it was useless to call them and all I would get would be aggravation. Someone, please help the consumer!

This top load machine replaced a top of the line Maytag Neptune. It has five water levels. It has three temperature settings and four wash selections. It also has a selection for an extra rinse that I use for white loads. The washer is very reliable. Clothes come out clean with an average amount of detergent. Although this washer is more than fourteen years old, it has never needed service or repairs. By running a cleaning cycle every six months, it drains like brand new. The stainless steel drum is still as polished as it was when it was new. Even the hoses have lasted with a need for replacement.

So sad, purchased brand new Maytag washer and dryer, Commercial technology (MVWB766FW) labels. Looked and appeared impressive. Machines cost almost $1,000 each. Had twenty year old machines that still worked, I didn’t want to face a unexpected breakdown and decided to replace. What a mistake. I’m 67 and all my life from grandma through my mother Maytag was the best, not anymore. Once my equipment was installed I washed a load checking frequently, noticed almost no water in the huge tub and my clothes being beat by the agitator but not enough water to move the clothes. I tried to change to high water setting but had to cancel this load to do so. Once on high water setting I started the load again, water still very low and agitator just rubbing the clothes directly next to it, no movement of the clothes at all. Ran completely through the wash cycle but when moving to the dryer noticed some light blue shorts had dry spots, many, which had never been wet even through the wash, rinse, and spin cycles. Had a warranty service call and was told this is how the machines work. I told the serviceman had I known that I would have never bought the machines. He told me the salesman should have explained this to me which he did not. The only way I can wash my clothes in the new, expensive machine is on bedding cycle with high water setting on. Sad day when American companies can legally sell such crap. Also, called the company where I purchased and ask about return. To that I was told once I made the purchase they were mine and Reid’s Appliance in Santa Barbara didn’t take returns. Reid’s Appliance can’t be trusted. Buyer Beware, this stuff is junk. I will be throwing these machines out soon as they aren’t even sale-able on the used market. MAYTAG RIPPED ME OFF.

MBL2258XES1 - Like most of the other reviewers, we have a Maytag refrigerator just 3 years old with a lower freezer that leaks water onto the floor -- and has been doing it for the last two years. We have to take the freezer apart (NOT easy), defrost it, take the back panel off, and clear the drain tube. Obviously a defective design! Cant believe Maytag hasnt done something about this!

My husband and I purchased a Maytag Bravos washer and matching dryer in November of 2009. At three or four months old, the dryer quit drying and was emitting a weird smell and smoky air coming out of it. It was under warranty so a technician was called. A fan blade inside it had broken. The repairman replaced it and the motor as a precaution. There was absolutely nothing inside it that could have broken the fan blade and I always check pockets. My hoses were clear also. He told me that it looked poorly designed inside for air flow. He made a box out of sheet metal to fit inside it that he said would help it with air flow on the inside. I still have the dryer but I dont like it very much because it still doesnt do a great job of drying. It has to run too long and at too high a heat to dry laundry. The latch on the door broke a few months ago and had to be replaced too. I havent had problems with the washer as of yet. I like the washer and it washes very well but I will not buy a Maytag washer or dryer again. WHIRLPOOL OWNS MAYTAG NOW AND THEIR PRODUCTS ARE ACTUALLY MADE BY WHIRLPOOL SO I WOULDNT TURN TO THEM.

This machine (Top-Loading High Efficiency MVWB755DWO) does not clean, it only leaves soap and moldy residue on clothes. The Whirlpool company refuses to assist even though it was delivered less than a year ago. So much for warranties! Wrinkles clothes, wrings incorrectly and does not give you freedom to manage independent of technological controls.

Deceptive company and won’t stand behind their product! Purchased brand new washer. Identified and reported noise that I can hear upstairs in my house while washing to technician. Changed a part, not related to the noise. Called back out. He admitted he could hear the noise. Whirlpool engineering department says normal. Sorry, I should never hear a clicking noise upstairs with two closed doors and 150 feet between me and the washer. Will be going back to Samsung next time.

I bought a Maytag dishwasher, model # MDB7749AWW1, in April 2011 and the control panel just stopped working. Of course, Im outside the one-year warranty, but judging from the other reviews on this site, that doesnt really matter. A $500 dishwasher should last more than 17 months! I agree with the other consumers. The control panel on these dishwashers should be recalled. Obviously, its defective. Instead, Im being told I can either pay $250 for the repair plus a one-year warranty or $130 plus parts to cover a onetime fix. Ridiculous.

My Maytag french door has worked steadily for 12 + years. It’s a basic model, ice maker in freezer. No door dispensers or electronics. I would buy it again.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

Contacted their customer service by phone and email numerous times...sent photos. They did nothing on a major issue,,three year old washer..now junk. Side of washer is rusting out the metal housing on washer is compromised.

We were excited to finally buy a new wash set and I always wanted the Neptune ones. I had owned a Maytag for 25 years through two children and a mechanic husband. I had every confidence in the new ones and expected at least the same service. Shortly after the warranty went, the machines both started to act up. The washer would stop in the middle of the cycles. The dryer wouldnt come on or wouldnt respond to the commands. We finally contacted the local repairman whom we have used for years. He came and gave us boo-hoos about these machines. He said they were trouble and we should have never have bought them. My husband figured it was the electronics in the control panel. The repairman said the parts would cost somewhere near $500.00 to $600.00 each and proceeded to try to sell us used ones for $2,000.00. We said we would try to get the bad parts and he even gave us the stock numbers? We went online and found new ones for half the price. We bought them and put them in and they persisted in doing the same things as before. Is this a runaround or what? Who is bilking who? Another great American rip-off. What can the public do?

Within 2 months of 1 year warranty running out, the control panel went wacky - does all kinds of weird things except work right. Called to see if there is any suggestions or work arounds and was told they would be glad to set up a service call for between $70 and $100, where they could tell me how much it would cost to fix. As with the other 100s of folks with the same problem, they basically said gee, you should have bought an extended warranty. If you have this many people with the same problem then it is Maytags problem, not the poor sucker consumer who got stuck with it. If you are considering this dishwasher, run, dont walk, as far from a Maytag or Westinghouse product as you can get. If anyone starts a class action suit against this product, please count us in!

Maytag Bravos washer and dryer both need replaced in 3.5 years! Control board had to be replaced on washer in under 2 years and now the replacement went bad in about 15 months. Maytag can’t help! Hundreds of dollars wasted. Dryer is not much better as the control board is now malfunctioning! DO NOT PURCHASE MAYTAG!

This Maytag dishwasher is beautiful inside and outside. I love that the controls are hidden. It cleans dishes very well. It has a large capacity for dishes, a rack for glasses/mugs, a small rack for cooking utensils, and a container for silverware. It is so quiet you hardly know it is working. I would highly recommend it.

I have a 2-year-and-5-day-old frontloader washing machine. The bearing and axle broke. The repair is over $500.00. It appears to be a known problem, as Maytag knew exactly what was wrong from the description of the noise it makes. They knew all the parts that would be needed. They would send the parts but not help with the labor. Evidently, it is a two-person job requiring several hours. They are not consumer-friendly and do not seem to care that the company reputation is going bad fast.

I always purchased Maytag products but no more. After 16 months of ownership of the MDB7749SAM1. For the last three weeks I have been washing my dishes by hand. This unit has so many defects that it should be recalled. Sick of buying parts!!!

I bought a Maytag Range with the Aqualift feature 3 years ago. Worse purchase every, the oven clean option (Aqualift) is useless. It do not work at all, be prepared to spend hours cleaning. I followed manufacturers instructions and its useless, after running the cleaning cycle three times I gave up and starting cleaning for hours.

Just purchased/used the washer. One needs water to wash clothes. I added water to the machine just to get the clothes washed. How can this pass any reviews when it does not use enough water to clean a set of sheets? Not to mention rinsing. Does anyone wash clothes in the group that designed this machine?

First we design the cheapest, flimsiest drawer possible on the bottom of the stove. Then we mount it on cheap plastic guides on a flimsy metal track. What a joke! Listen, drawers have been around over 700 years. If you cant do better than that, you need to look for another line of work.

I purchased a Maytag Centennial Washer at the end of last year. Within 2 weeks, I knew it wasnt a good washer and asked my husband if we could return it. He said, No. I dont like using the fabric softener dispenser, so I used to use a Downy ball. This washer doesnt spin hard enough to open the ball. I tried 3 separate times. Each time, the ball came out with the fabric softener in it at the end of the cycle just like it was when I put it in. It also doesnt get the clothes clean. Im using chlorine bleach, detergent and OxiClean and our whites are gray. It doesnt get the simplest stain out and the soak feature is a joke. If you use the soak feature, the washer fills up, the lid locks, it soaks and then the water drains out. No spin or anything.Normally, on the old washers, you could just push the knob in to stop the agitation to soak something, but not now. The lid locks, which I cant stand, when the washer is working. I would like to see if it is agitating or to add more clothes if I want. Im not sure who designed this washer, but they should go back to the drawing board. Ive tried every cycle and none of them work well. It also takes an hour to wash a load of clothes. Im just so disappointed with Maytag on every level. This was my first Maytag purchase and it will be my last.

Purchased a new Maytag washer top load/Dryer set on April 1, 2016. Having trouble uploading receipt but I paid 1,145.83 for set. It took 2 weeks to get it delivered on April 15. 1st use it shook and wobbled even though the load was balanced but Ive read that is a problem with these machines. 1st load of clothes, washer didnt fill with enough water to wash properly - 3-4 inches of water for a full load of jeans. Top 2/3 of clothes hardly got wet! Changed the setting, same problem. Changed the setting again, same problem. I had to stand at washing machine and keep lifting the lid to get more water in the machine. Clothes didnt rotate in machine so all the clothes on top half didnt get cleaned. The spin cycle is scary! You could hear clunking noises and it had nothing to do with load being balanced. Did a small load and same thing with water level and spin cycle. Called Home Depot to pick up both machines on next business day. The dryer lint trap is so long, it made a mess trying to remove the lint even after only 1 load. NEVER AGAIN MAYTAG! Ive never regretted an appliance purchase like I do now. Maytag and April Fools day are a perfect match. Only its for real and not a joke.

Bravos 4.3 High Efficiency Washer - The worst washer ever. I recently returned from burying my step-mother. She actually used the same washer and dryer, by Maytag, for over 50 years. Those days are gone forever. This is my second set of Maytags in ten years. The first literally stopped working just after the first year warranty ran out. I still have them inside my pantry, like a set of anchors. Notwithstanding that, I thought, Maytag was a good brand, it must have just been the style of machines, so I purchased these in January. After over six months of usage, I am amazed at how many times I have to wash a single load of clothing to get the items clean. Who cares if the machine saves water? What was wrong with having an agitator? I literally have to remove freshly laundered clothing, turn it over and run the wash again to get the top of the laundry clean. I have had a blanket finish for the fourth time to get it clean, only to have to hang it outside because it is so full of water, the weight keeps it from spinning properly. And why would you remove a timer feature which permits very busy, working people, to wash their items while they are on the way home or in the middle of the night so that there is no waiting to pop the clothes in the dryer? None of the cycles takes less than 80 minutes to complete. Who has 80 minutes to wait on the washer to do its job? I am so upset about the amount of money I spent on all of these machines. Just think, I could have brought the over 50 years old set home from my step-mothers and had a washer and dryer do what they were supposed to do -- clean the clothes.

Wish I had reviewed Consumer Affairs reports. When our old Maytag stove required repairs we decided to upgrade old stove instead of putting money into old unit. Looks like a huge mistake. Not only was there a delay in receiving unit after placing order but oven will not preheat. Two weeks before Thanksgiving we were promised a working unit. Now we are only 2 days from Thanksgiving, 2 repair companies have been at home to repair. Requires new circuit board and a new regulator to repair and no promise we can obtain parts. Now I have to figure out how to feed my family for holiday. I am pretty well done and after reading other reports that they are better in junkyard I think I will try to make them take back this defective Model 8800 product. Sitting in our kitchen unusable for the holidays. Dont buy Maytag as customer service does not exist.

I give the product lowest and poor rating. The bearing in our washer went bad 4 months after we bought it. For the fourth time, they are coming out to repair the washer on 01/11/2012.

I bought the washer dryer combo. Dryer already broken. Washer is very loud when it changes gears. Would not recommend the washer or dryer.

I believe the Maytag Bravo washer and dryer was manufactured so the Maytag man would have something to do once again! Buyers Beware! My $800 washer broke down 1 week after warranty costing me $400 to repair!!! Half the cost of a new one... now the dryer is making horrible noises. I fear calling for repair... or should I just buy a new different one?? My last washer and dryer lasted 30 years!!! Bravo certainly did not have all the kinks out of them before marketing them! The cost is to the consumer who trusted the name! You cannot return a 2 year old appliance! The laundromat would have been less costly than this washer and dryer! Maytag should be made to recall these defective machines or at least repair for free. Do not buy!

Bravos washer, a year old machine, needs new main electronics board $220.00 plus $125.00 labor to install. Repair guy said humidity makes them go out. Go figure a part sensitive to dampness on a wash machine. Why don’t they seal it better? By the way, this machine does not wash, worth a crap. I am getting something new.

Maytag washing machine exploded sending glass shrapnel everywhere. At this point I believe Maytag should replace the machine. I appreciate after MANY hours on hold and being transferred that you are sending a repair person out, but there is tiny glass shrapnel all over inside. This is crazy, and a MAJOR safety concern.??? Update - can’t find parts or an eta. Replace the machine!

I really love my front loader and it has no agitator to rip pockets and tear off buttons. The tub is very large and I can wash king quilts. I do miss being able to fill the tub and put in additives and then add the clothes to soak.

I love the way it can really handle large loads. The dryer is the best though. It actually dries your load without you having to turn it on more. There are many different choices that handle drying. So, no more to the bone drying.

My dishwasher is two years old and it just stopped working. I called the store I purchased it from and they sent out a repair man. He told me that the control panel was damaged and that he would have to replace it. The cost is $145.00 plus the $50.00 service call. He said something must have spilled and got into the control panel. It is a built-in dishwasher underneath a kitchen counter. I think it should somehow be protected against spills and/or moisture getting into the control panel as it is underneath the kitchen counter. I do not remember spilling anything that ran down the front on the dishwasher. But even if something spilled, if it was made properly it should still be working. I will not recommend a Maytag to anyone and will also spread the word about what happened. Unhappy in Pennsylvania.

The brackets that make the door open and close are just screwed Into the plastic lining with no kind of anchors. If you use the freezer a lot the screws come loose. Can’t close the door. And then 300 dollars later a service call. All to replace a screw. That’s just fine but the hole is stripped because no one could install a 50 cent anchor on installation at the factory. No more Maytag for me.

I also purchased a Maytag dishwasher a few years ago. It has never worked that well. We had a repairman come out once to replace the control board but the problem soon returned. Interestingly, we found that if we wait long enough until the control panel is in the mood, the dishwasher works again and the control panel responds to button pushes, until the problem returns.I dont recall what model I purchased but it seems to be irrelevant. From reading the other customer complaints, its quite obvious that all Maytag dishwashers inherently have problems with their control panels and Maytag intends on doing nothing about it. I guess the extra repair costs that their customers have to pay for their defective products brings in some additional revenue to Maytag, so theres no real motivation for them to fix their ** products.

I am online now because we have the same problem. Our refrigerator is less than 2 years old. Watched a video on YouTube how to fix problem and repairman said engineers who created design must have been on drugs. I think hes right. Very common problem. Have to call repairman!!

Oven is not even 2 yrs old but, the bottom oven floor lining is crackled & flaking. Although they say the cavity is covered under the 10 yr warranty, they say its not covered. Basically told me theres nothing they can do for it. I bought all Maytag appliances for my new home because they claim they stand behind their product. The 10 yr plaques on the appliances are a joke. So disappoint.

MVWC565FWO Maytag Top Load - Bought a new washing machine less than six months ago... extremely noisy: Clank, Clank, Clank, Clank, etc. Reviews said it was just noisy, nothing wrong with it. Last week it would not spin the clothes dry. Now when it is plugged in, it does nothing but run the pump! No lights, no water. Also the deep wash was never deep at all - barely covered a modest load of laundry. Repair coming today. Wish I could return it.

Purchased a Maytag top load HE washer in November of 2011 & by Feb. of 2012, Maytag had to bring me a new one after a service call to fix lasted only one week. So at the end of Feb. 2012 they brought me a new Maytag Centennial HE Model# MVWC400XW3 & this one lasted till January of 2014, less than 2 years old & quit working. Had a service man come out to look at it & was told not only it would need a $400 repair but it was made by Samsung, but Maytag had their nameplate on it!! Called Maytag customer service line which took about 30 minutes of hold time to get through & was told, SORRY, LADY, we cant help you. Youre just out of $613 after less than 2 years of service & we WONT help you!! This company should be shut down, they are liars, frauds, cheaters, producers of poor quality products, uncaring, & sellers of the worst products on the US market & I hope the Consumer Affairs will see enough of these complaints about Maytag products & shut them down!!!

It seems to be a broken record with other reviews. I had a 2 year old microwave and the door doesnt recognize that its closed. Which means it wont turn on when I close the door. So you have to open and close it maybe 30-50 times and sometimes it works. I call Maytag who schedules a company but doesnt disclose anything about the warranty or service cost. I was thinking it would be a nominal fee since it falls under a 10 year warranty. The company calls and confirms the cost and I recheck with Maytag who said that the warranty only covers parts. So I buy a $300 microwave and have to pay $160 for a service visit because your company made inferior parts. Absolute sham of a company. Buyer Beware...

We have had washer/dryer Bravo Series and been nothing but horror stories. Washer bounces all over room to point hoses come out and flooded my laundry room and foyer and garage. It takes over 1hour 45 minutes to do loads sheets which is 2 sheets 2 pillowcases. The repair man told me that takes that long due to MY sheets are dirty. I have been married 46 years and never heard that ever!!! The dryer is just as bad, takes over hour and half to dry sheets and towels almost 2 hours to dry. DO NOT BUY MAYTAG ANYTHING. The person who said needed hurricane straps to hold washer is something I agree with. Just a horror.

I bought a Maytag commercial washer - it was pricey but I loved the fact that it had dial knobs and only one feature was electronic as I find the electronics to be what fails the most. It holds a lot of clothes and gets them really clean. I absolutely love it!!

We have reported the first time use of New Gas Range using the oven and range top at the same time is impossible because of BURN HAZARD AND the response was soft with no explanations. The range arrived March 26, 2015. We were impressed with first baking only. Family arrived at our vacation home for Easter celebration. Our first meal on Good Friday using both oven and range top was a disaster and the cook was burned on the stainless steel knobs. The oven vents below the knobs were about the temperature of the 380 degree setting of the oven!We rendered the unit unusable and called Maytag customer care department during the late table dinner. I explained on the 45 min call we were having this event and would be all leaving Thursday and their solution was 8 to 10 day shipping of Fake composite stainless looking knobs. These knobs will have to be sent to our Ohio home 500 miles west of the Range location?? If they could ship that day why not overnight??THE SOLUTION OF WEARING OVEN MITTS FOR STOVETOP COOKING IS NOTHING SHORT of silly to conduct meals for our guest. And other members of our family that we permit occasional use of the home open to burns using this Range until we drive 1000 miles round trip to drive the knobs back to NJ from Ohio??? Customer Care fails to listen. We will not be returning until May. To illustrate my concerns about the logistical issues I asked if Maytag would pay for the mileage and tolls for me to replace BURN proof knobs. Oh and will it work or melt? Furthermore who will pay for the takeout needed to feed our family? He did not get it and consulted with supervisors for most of the call therefore 45 min of wasted call. No solution, self installation on an $800 Range. Dissatisfied CUSTOMER with an unusable Gas Range Burn HAZARD!! Poor Design oven vents less than 2 inches below stove knobs! See Photos.

Quiet, well priced and reliable technology which makes owning this dishwasher an easy buying and owning experience. Having the brand backed with great reliability and if needed excellent service makes the buying decision easy for the consumer.

Maytag Dishwasher Model MDB6759AWS3 Does Not Start - If you are having the following problem, here is what I did to fix it. All of the lights on the touch pad would light-up when pressed but the dishwasher would not start. It appears to be a corrosion problem on the connector from the touch pad to the control panel. 1. Turn off power to the dishwasher. 2. Remove the inside cover to the dishwasher door - approximately 10 screws. 3. Disconnect the electrical connections from the inside cover to the control panel still attached to the door. These are snap connectors. Always a good idea to label the connections before disconnecting in order to make sure everything goes back together properly. 4. Remove the black cover on the control panel. There are 3 screws. 5. Find the green conductor tape that connects the touch pad to the control panel. 6. You will remove the green conductor tape from the control panel. DONT just pull on it. There is a white piece of plastic that slides away from the control panel and toward the green conductor tape. It will remove pressure from the conductor tape and the conductor tape can then be disconnected from the control panel. 7. Get a good pencil eraser and clean off the exposed copper connectors in the conductor tape. 8. Place the conductor tape back into the control panel and slide the white plastic piece over it to reconnect the conductor tape to the control panel. 9. Replace cover on the control panel. 10. Reconnect the electrical connections from the inside cover to the control panel. 11. Place inside cover of the dishwasher over the proper screw holes - make sure the bottom of the inside cover is overlapping the bottom of the door - or the door wont shut properly. 12. Replace screws.13. Turn on power and check.It worked for me and saved me time waiting for a repairman and expense of the repair.

Purchased Maytag Dishwasher MDB8959SFH4 as part of a kitchen renovation with hardwood floors. Realized that the dishwasher was leaking intermittently. Appeared that the door wouldnt latch properly. Called Whirlpool (parent company). Technician came out to assess the situation - couldnt recreate the problem so suggested replacing door seal. I try to explain to him that in my opinion it wasnt the door seal but a failure to latch because the top rack was not retracting completely on an intermittent basis. He also suggesting replacing the latch. Repair was carried out and same issue arose three days later. I systematically removed one dish at a time and then tried closing the door - after removing about the 6th item the door closed. Called the repair company today and they told me he had just received a recall from Whirlpool - apparently an issue with the tracks not allowing the rack to retract properly - what I have been saying all along. I called Whirlpool but they insisted the notice was sent out some time ago. I called Home Depot where I bought the appliance and they confirmed that they were not aware of this issue. I suggested they should not be selling this dishwasher until Whirlpool remedy the manufacturing defect. I will follow up with Whirlpool to let him know I have spoken with Home Depot and they were not aware of the issue.

We purchased a bottom freezer refrigerator from the Home Depot in 2013 and I am sorry to say this refrigerator does not deserve any stars. Immediately after the warranty was up our refrigerator started leaking all over the floor. The drain clogged and freezes up on the bottom under the freezer. When it becomes full, it leaks all over my hardwood floor. I have now become a slave to this refrigerator. Each week I have to open the freezer and get down on my hands and knees to break up the ice, scoop it out, toss it in the sink. I have spread the word and I hope anyone who reads this does as well. Never buy a Maytag product because not only do they make defective products, they wont own up to it and recall it.

Not only does the water not drain properly causing an insane amount of stench of moldy water being trapped, but this washer has had nothing but problems since we got it. Error code after error code, problem after problem. So disappointed. My husband wanted an LG and I said it had to be Maytag because Maytag was the best. Thanks for making me a liar Maytag!

Purchased new about 3 years ago, doesnt clean, ties clothes in knots, leaves white spots from softener that doesnt get wet sometimes after cycle, some areas are still dry after untying. Now error code 51 keeps appearing, service man 4 times replaced rps sensor as directed, nothing changes. Need a chain to drag behind truck, no technical support from Maytag or whirlpool. Old ones of 20 years still worked good, gave to niece. Lucky her.

We purchased a dishwasher (Maytag) two or three years ago. We have had nothing but trouble with it. The welds on the upper rack broke. The wheels on the low rack keep falling off. Water leak happened recently. The start button broke. My wife and I decided to just get a new one rather than keep sinking maintenance costs which are going to keep adding up.

I purchased this washer January 2020. Bravos XL model# MVWB830DW5 is the worst washing machine ever. Does not clean your clothes, leaves soap residue on your clothes. Clothes aren’t fully submerged in water for the wash or rinse cycles. Do not waste your money. You will be highly disappointed.

Had our house built in 2009 and the builder carry Maytag Appliances. After 3 years every single appliances start giving us problems. First the refrigerator not getting cold, got it fixed. Then the dishwasher panel, then the built-in microwave, then washing machine. Just the other day the refrigerator broke down again and I was told the compressor was bad. Really? Whats going with this company? All the appliances from this maker dont have longevity. I have 20 year older refrigerator from GE and its still working. Please do not buy this garbage... Its a waste of your hard-earned money.

We bought a Maytag dishwasher (Model: MDBH979AWS3) in January 2010. In April 2012, the control panel stopped working. A local repairman came out to see it for $160, diagnosed it, and suggested that we call Maytag to see if they would give us the part because it was only a two-year old machine. He did say that the control panel was not a part that was troublesome!Maytag offered an extended warranty for only $287 that would cover the part! The total repair cost was almost equal to the cost of a new machine. Home Depot, when consulted, acted as if they know nothing. After reading about other peoples experiences with this company, I feel that it is no longer an honorable company standing behind its products. In fact, the whole repair process is set up to rip off the consumer.We will now look to purchase the best and cheapest non-Maytag product, not from Home Depot, and throw it away when it gives out, which more than likely will be soon. These companies have finally convinced me to do what I am sure what they have always wanted every consumer to do. Throw it away when it breaks down.

I bought the Maytag Bravo XL MVWB725W washing machine and dryer pair in August of 2015. 2 months after I bought the pair the thermostat went out on the dryer. It was under warranty so it was fixed and no problems after that. In July of 2016 I have my first stainless steel hose break at the fitting because of corrosion flooding my laundry room. I thought it was a fluke so I put another one. The next hose started to corrode in September 2016. We thought there was some weird chemical reaction going on between the hose and the filter on the back of the machine. So we changed to rubber hoses in September. Since then we have gone through 6 sets of rubber hoses. We have had the water company out, they say our water is fine. A plumber out, our new water heater is fine as is our plumbing. An electrician, who changed an outlet and put a grounding wire on our house water line. And an appliance repair man, he found the problem so he called Whirlpool who makes Maytag. There is corrosion on the water temp control. However nobody has EVER seen this problem and doesnt know how to fix it. Not even Whirlpool. And Whirlpool says its my house. Im at a dead end with a washer that is constantly going through hoses. It really doesnt wash clothes very well either unless you put a lot of stain remover on the clothing before and wash it in hot water. And yes it is noisy. Dont buy this product.

Maytag front loader 5000 series error codes - After using my washing machine for 3.5 years, under light duty, I have an error code of SUD and F35 indicating that the pressure switch has failed and needs replacement. I will need to buy a new pressure switch out of pocket and replace.

I have the Maytag Bravos washer and dryer. The machine has broken several times every year, and every year, Maytag makes me feel like it is my fault. They built a machine, and they do not stand behind it. And I cannot get a local machinist to work on it. I have asked Maytag to replace it from the start, and they refused, telling me its out of warranty. The only thing out of warranty is the frame--all parts are new. Here is the history:On 1/04/2008, I purchased it from Home Depot, and it cost $815. Then in 4/2009, there was an F51 code, and Maytag replaced the mother board after long hold times and much pleading to help me. They said they could do nothing, because it was out of warranty. It took manager to manager to manager to get the agreement to extend the warranty. (I then found that this was a regular Maytag issue.)From 9/2010 to 10/2010, an ld code occurred. The approved Maytag scheduled service had to come out 4 different times to attempt to fix the issue. One time, they said it was broken wires for the drain pump. The next, it was off balance; and the next, it was a sensor. Then the next time, they replaced the mother board again, and again after much argument that the part was less than a year old. Each time, they get more and more difficult to deal with and made me feel more and more like I am asking them for something unreasonable. The service guys said the washer was like new.... All new parts and I would never have a problem again. It cost $80 after argument, and Maytag covered the parts.Last 2/2011, problems include a fast spin, ld code, and off balance; and it stopped working. It needed new suspension rods which cost $250. Maytag paid nothing. Then in 8/2011, ld code started again, and I would have to turn off to drain and then restart to spin. Maytag called in a service call, and they never showed up. Every time, they said they read over my file and that theres nothing they can do to help me. And no one else for me to speak to.In 10/2011, the ld code came on permanently. The Maytag call I made this time again said there was nothing they could do to help me.I am so frustrated; I dont know what to do next. I threw away an older set working washer and dryer, thinking I made a great decision to upgrade to this new set. Now my family of 5 cannot wash our clothes. No one will work on the washers locally, and Maytag treats me like Im complaining for nothing and I should just spend endless dollars to fix this machine. And Im at a loss. I had to get a part for the dryer the other day, and the parts store person told me that this washer is one of Maytags mistakes. if that is so, why wont they help me?

Magtag Bravos Washer top load Model MVWX700XW1 - I purchased my washer in June 2011 with the understanding that this was the best washer for my money and needs. I have family of 4, and laundry is a continual cycle at our home. I had the washer delivered and installed by the store where it was purchased. I was pleased with the machine even though the clothes were extremely wrinkled after each cycle, but the salesman was kind enough to tell me this would be so. 21 months into use, I had a water leak from the internal cold water valve. It’s not covered by warranty; I had the valve replaced. Within 2 weeks, the machine would not spin out the clothes; if it did, they were still wet, or would stop mid-spin cycle and start rinsing again. It took 2 hours to wash a 37 minute hand washables load this past Saturday, 4/6/2013, not to mention the other 4 hours washing to regular loads just to get the machine to rinse and spin. The service technician has spent the past 2 days at my home trying to repair my machine to tell me today that it is not the lid lock, but the master control panel which is still not covered under the manufacturer’s warranty. To say the least, I now have to purchase a new washer as I have invested $250.00 for a valve and the control panel is $275.55 plus labor.This machine is the biggest waste of money that I have ever spent. I have been a loyal Whirlpool customer having owned two other Whirlpool machines, each lasting 17-18 years each. I do not abuse my appliances, overload or in any other manner try to destroy a machine for personal gain. I do, however, feel that Whirlpool/Maytag needs to recall these washers or cover the parts beyond what is written. I have read numerous accounts of these and similar issues by others, yet the company will not stand behind their appliances. Really!

First I would like to thank the salesman who has worked diligently to solve the problem I am having. The first load of dark clothes I washed came out with what looked like lint on them. It has to be scraped off. Yes I am using HE detergent. Yes I am using the minimum amount recommended by the manufacturer. & yes to all the other questions I have asked. The solution was to wash the dark clothes on power wash with an extra rinse. Very energy efficient! This was NOT the answer so I was given a 1-800 # to call. After giving all the necessary information & answering all of the questions about detergent etc. the conversation became a little more in depth. Does it happen with dark clothes? Do you dry your clothes outside or in a drier? It was becoming obvious to me that Maytag is aware of this problem. By this point I was even unhappier as no solutions were being offered. Finally after several would you mind holding the line again for just a minute he said he couldnt tell me to do this but some of his friends add a cup of vinegar to their wash. At this point I told him I was sorry I had ever bought this machine. He then said he would have a technician arrange an appointment. He arrived & declared I was using too much detergent even though by then I was using half on the manufacturers recommended amount. Buying an energy efficient washer where I have to use POWER WASH, EXTRA RINSE, VINEGAR & DRIER is not a good answer for a problem Maytag must be aware of as I read the reviews today. I have just done 2 loads of dark laundry with no detergent & the pants are marked so I WANT AN ANSWER.

Washer Model MVWC555DWO. I dont like this machine. I thought Maytag is a good brand name, but I dont think so anymore. The engineers who designed these new machines with the water level saver dont do laundry. In order to get the cloth covered with water, I have to use the bulky sheet level. I have 2 jeans and a sheet that got holes in them, because the water level was not right. I would have my old machine repaired, if I have know how my new one would do. Im stuck with this machine. I dreaming that this machine breaks down soon and I can buy a new that has a better water level. My old one had water saver level too, but did a great job with the water level.

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

Bought this because of the load capacity and it seemed like it would be a good purchase to help save on water. But worst mistake ever. The water level barely touches the clothes on top. It barely has any water whatsoever. All my dark colored clothes come out with residue. It’s disgusting and cleaning with Affresh does no good either. Very disappointed with the company.

We bought a Maytag Refrigerator, Model MSB27C2XAMSS from BrandsMart on 2/4/2015. Today, I made my 4th Service Call for the Ice Maker not making ice. The service department has replaced the icemaker, repaired it and still does not work. When I call for service I usually have to wait 5-7 days before I can have a technician come to my home. Also, the refrigerator door does not close unless you push it completely to the refrigerator, unlike most refrigerators that I have had. I would never buy another Maytag refrigerator and certainly will make an informed and researched decision before buying another refrigerator. I am truly dissatisfied with this refrigerator and would suggest looking for other brands.

The Maytag Bravos Washer we bought had a stinky odor we couldnt get rid of. We found that clothes had gone over the basket and lodged in the filter above the pump; end of stinky smell. Later, we found that pennies and other small items had slipped into the fins of the drain pump and ground them off. The filter does not keep out of the pump and is not made right to stop damage. I called a local Maytag dealer who said he had a lot of similar complaints. I called Maytag who stated they have no registered complaints of this type and had no fix for it. Avoid the Bravos line of washers - they are not made right and Maytag will not admit it or help you. Bravo for Maytag who are obviously not going to act on it. Make a formal complaint and find if someone has a lawsuit you can join!

DO NOT BUY THIS MAYTAG REFRIGERATOR. Purchased 9-30-19. Delivered 10-4-19. 12-9-19 - Not Cooling, Called Whirlpool on hold for exactly 1 hour. 12-11-19 - Repair service here - ordered new Control Panel. 12-17-19 - New Control Panel Replaced. 1-6-20 - Freezer is not freezing. Control Panel going up and down and blinking constantly. Called Whirlpool - on hold for exactly 1 hour. They called service repair. 1-8-20 - Service Repair here and ordered 2 thermostats: 1 for freezer and 1 for refrigerator. 1-15-20 - Service Repair here to install 2 thermostats - At this time I purchased the extended warranty for $119.30 for 3 years.3-1-21 - Control Panel completely went out again. I called Whirlpool - on hold exactly 1 hour before they answer phone. I am so pissed. They call Service Repair. 3-3-21 - Service Repair here. They order new Control Panel. States these panels are continuously going out and they are having to replace them everywhere. 3-12-21 - I called Service Repair since we havent heard anything. ETA on control panel from Whirlpool is not scheduled until 3-19. I am really pissed by now.In the meantime I have been on hold with Whirlpool for 47 minutes. At exactly 1 hour being on hold, they answer my call. Im told I have to wait. There is nothing they can do. I told her we were buying ice every other day at $10.07 for 2 20# bags and they wont replace money. Told me to throw my items away and they would replace all the food for $250.00 one time during the 3 year contract period. The service is Customer service on their contract is terrible. Waiting for parts is even worse. This is a piece of crap appliance and we will never buy another Maytag.

We bought our Maytag Bravo top loader on May 5, 2010. The machine was working fine. Then last week with no warning, the F51 error code popped up. We called Sears and they sent a repairman out. The result was the sensors work independently from each other (tested correct in the Ohms range). It made it through an entire diagnostic test, but will not complete a wash cycle. The repair guy concluded that the control board was bad. Estimated cost to fix was upwards of $400. I cannot afford to fix. Our issue with this product is that it is apparent, from reading all the forums, that this is a known issue. And we believe Maytag should be reimbursing consumers for this repair or they should recall the washer. Our washer is used on the weekends and it should have lasted us for minimally five years. All we wanted was to make it through one military overseas tour with it, not asking much. Instead, this machine lasted two years. Unacceptable.

I have always hated soft touch control panels so I purchased a Maytag Dishwasher with old style push buttons. IT DID NOT CLEAN THE DISHES, so Lowes took it back and I was convinced to UPGRADE to an MDB7749SBB0 and was told this machine was top of the line, although it was VERY temperamental from the start. I guess I should have done my homework. I see now several complaints about the control panels not working. I was told that MAYTAG was a very reputable company and that they stand behind their product. WRONG!. The company KNOWS these panels have problems and should replace them free of charge as it is obviously a defect. Nope, first they offer to send someone out (In a week) to repair it at $80 just to look at it and the panel is over $100 to replace, and when I complained they tried to sell me extra coverage for $250. REALLY? What is the purpose of purchasing a QUALITY dishwasher? I might as well purchase a cheap dishwasher and replace it when it breaks. I think you should be responsible for your product when you have several complaints on a specific part.

I bought my fridge (Maytag French Door Fridge MFF2258VEW) in September 2009. It took forever to get it and when it was delivered, the door was dented so I had to wait for a new door to be replaced. The fridge stopped cooling just before Thanksgiving 2011. I had to throw out a lot of food. It was the circuit board and that was covered under the warranty. I noticed a couple of months later that the freezer was freezing up again and was worried that the fridge would go out again and in February 2012, they came out again and it turned out that the freezer had been put back incorrectly and the freezer gasket didnt fit right and thus, the freezing up on the circuit board. Now it is May 21, 2012, and I came home for lunch to find the fridge not working again! I cant get anyone out to fix it until Wednesday, the 23rd. Now we are in warm weather and I just went to the store and had a full fridge. I still have the warranty and will for another 14 months. I think if this continues to happen and when the warranty is up, we will have to replace this fridge. I can tell you for sure that it will not be another Maytag! What a piece of junk!

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

Do NOT buy a Magtag washer. I purchased a brand new washer from Lowes in 2017. The washer gets stuck in the wash cycle. When I called Lowes, they said to call Maytag, who sent a service person out. The service person recalibrated the machine never ran a cycle and left. We had to call two more times after this for the same reason with the same result where the serviceman left without running a cycle. This was all while the product was under warranty. Since I had three service calls, I called Maytag frustrated that this kept happening to a new product. I was told there was nothing they could do, but if it happens again to have the service guy come back out. When the warranty runs out, I will have to pay for the service tech. Unbelievable. Save your time, money and frustration and buy a Whirlpool! I dont know how Maytag gets away with selling defective products.

Purchased a new stainless Maytag dishwasher model # MDB4949SDMO ser # F54240259 on 10-20-2015. Installed about three weeks after purchase. This unit is terrible -- has not properly operated or cleaned our dishes since installed. First service came shortly after install. Complaint was unit leaves white film on all dishes. (Soap used is cascade which was recommended by Maytag in owners manual.) Technician installed a new water fill valve because unit wasnt getting enough water. After that unit still no good as unit became noisier and noisier and still leaving white film on all dishes. Second service call: the technician indicated entire noisy pump assembly would have to be replaced and would need to order it. Third service call: the technician arrived and replaced entire pump assembly, taking the old one away with him. The technician said it will be good now. It wasnt, but at least it was quiet. That was in January 2016. This unit still does not clean dishes properly -- continues to leave a white film on everything requiring hand scrubbing to remove. All dishes are hand rinsed with hot water before loading them in dishwasher, but actually dishes are more dirty three hours later after the cleaning cycle has finished than before they were put in. After having to buy new glasses and plastic ware because stubborn white film will not come off and looks disgusting. Tried various different soaps and rinsing products to no avail.Finally contacted service department for the fourth time and today technician arrived and found the unit to be mechanically functioning as it should and can do no more to help. Said to try a product called lemi-shine. Maybe my water is too hard also he said, even though we are on city water! This is our third dishwasher at this home and have never had hard water associated issues. All I want is my full refund for this defective product and I only get the run around from Maytag. Stay away from this machine.

I renovated my kitchen 3 years ago. I decided on purchasing new appliances which included refrigerator, dishwasher, microwave, range, washer and dryer, all of which I got from Maytag. Of course they were always known for dependability but apparently they were not! What happened to this American product? In the last 3 years, I have had my refrigerator (**) serviced 4 times for the same problem. Each time servicing has been a nightmare at the hands of AE service, Preway service and of course at the helm of my nightmare Maytag Customer service. The first mistake I made was purchasing Maytag products followed by the second mistake of purchasing Maytag service contracts. I now have a refrigerator that is not working, waiting on parts since end of august. When I called Maytag customer service, they confirmed the parts were not available and recommended I go online and try to find the part! This added insult to injury. Today, Preway service finally came to install my parts and upon technician’s arrival he opens the part box and realizes he ordered an ice tray cover, when he should have ordered an Interface Control Board. Maytag continues to have their products serviced by incompetent companies and appears to have no interest in keeping you as a customer after you purchase, whatever happen to the dependable people?Maytag had built their reputation on reliable products and dependable service, what happened to this American Made appliance? Here is a prime example of what happened, and why companies like LG and Samsung are gaining more and more customers every day. The best advice I can give someone is avoid Maytag. By the way, I forgot to mention I have 2 small children ages 3 and 4 and Maytag is not concerned about how I would provide food for them with a refrigerator that does not work. Shame! This is not what I expected from what I thought was a reliable company.

Purchased a new Maytag refrigerator in January 2013. In September 2013, the ice maker stopped working and Maytag sent out a repairman to replace the ice maker. In February 2014, the ice maker stopped working again. I contacted Maytag and was told the refrigerator was no longer in warranty. I told them that since the ice maker was replaced in September the warranty should have covered me for a year from that date. The Maytag representative told me that was not had it worked and asked if I wanted them to repair the item for a fee. I bought a non-Maytag ice maker and replaced it myself. It is now July 2015 and the ice maker is still working fine. I am not a repairman.

If I could rate it lower than 1 star, I would. We bought ours new in 2005. Within 6 months, the main pulley for spinning the drum fell off not once but thrice. The repair tech said that the shaft was machined incorrectly at the factory and the bolt that would normally hold it on was backing out. The 3rd time it happened was close to the end of the warranty and the tech could not make it out before the warranty date. When he did show up, they wanted to charge us. I wound up putting the part in myself. Two months later, the suds alarm came on, which caused the water valve to open. The pump kicked out and the water valve stayed on flooding my basement and the electronics in the washer. This happened twice. The second time was a week ago and I tossed the ** out to the curb. We also have a Maytag Gemini double stove which does not work either. This is the second and last Maytag appliance that I will ever own. They are junk!

Purchased a Maytag Centennial Washer from Lowes. This is the NOISIEST WASHER I HAVE EVER HAD. Self Balancing, pretty much the way it is, YOU lift that heavy wet laundry and re-arrange to balance. It just slams around even moving the washer, until you do. This washer also doubles as a BLENDER. It SHREDS laundry. The agitator does not go all the way down and thus, clothing, towels, rugs... get stuck under the agitator, wind around and RIP. Have had hundreds of dollars worth of laundry shredded such as: shirts, towels, new rugs and it even ripped the waist off a pair of my jeans! The other laundry gets tied up on the stuck laundry and you end up with a twisted, ripped, tied up Laundry Ball. It will not wash or rinse well when it does this, naturally. Lowes: The salesman knew about all this, and sold it anyway! He had one and got rid of it. Gee thanks Lowes and Maytag, for the worst washer I have ever had the misfortune of owning.

It’s a front loader, very quiet, and uses less water. The clothes come out clean and less wrinkled if you take advantage of the settings. l like the extra rinse and the drawer underneath. The capacity is able to accommodate enough clothes so I only need to do a load of darks and a load of whites each week.

MER8700DH - Within 6 months, left rear burner stopped working and Maytag repaired it under warranty. Within next 6 months, and just before end of warranty, right front burner stopped working and again Maytag covered it under warranty. Within the second year of ownership, the oven was not working correctly and Maytag refused to cover it because it was off warranty. So I called a local appliance repair company who gave me an estimate of over $300 to repair it and basically advised against repair stating that this stove was a piece of junk. So I replaced it with a GE and junked the old one before it was even two years old. I filed a complaint with Maytag. At first they said they would go half on the labor, but then they said I should have bought the extended warranty and refused all further help.