Purchased Maytag dishwasher model # MDB4709PAB3 8/2012 @ Lowes in NY with extended warranty. After a while, noticed wood floor warping in front of appliance. Called repair and after several tries, they couldnt repair leak under door. After many complaints to Lowes and Maytag, was finally issued a new dishwasher 8/2013 same model #. Person that hooked it up couldnt wait around to see if all was okay. Ran dishwasher after he left and as usual for this model it leaks worse than before. Called Maytag complaint dept and they said they would issue me another dishwasher of my choice and same price through Lowes. But they never spoke to Lowes and Maytag will not call me back. I would think there must be a leak problem with this model. Do not buy. It is not worth the trouble!

Hate my Maytag Centennial Commercial Technology washer. It takes well over an hour per load. Clothes come out very wrinkled, and my knits get holes very quickly. I would not recommend this machine to anyone. In fact, I warn people against it as I have been frustrated every single time Ive used it. Model # W10420382A.

I bought a Maytag washer 6 years ago. Energy saver. Less water. Nothing ever seemed clean. Always white streaks and I used liquid detergent. So we went out and bought another Maytag with agitator June 2017. Never drains properly. I will never ever buy another Maytag product.

Hello, My recently purchased dishwasher has leaked water within less than half an hour of the fifth time to be used and showed error: F8E4, dishwasher model and SN are: Model: MDB4949SKZ. Serial # : FA3003347. Registered: 09/11/2021, Ive been calling Home Depot who in turn asked the installer to check the connection, and the latter advised and reported its a manufacturer issue. And calling Maytag for several times but no response or action. On-line service scheduling of Maytag is not working!!! And the live chat is not helping, as well. Now my dishwasher is not working since more than two weeks, knowing that it has been installed only a month ago.

Bravos MCT maytag commercial technology washer - Bought this washer a year ago. Will not complete cycles. Will not agitate. Never buy Maytag.

Freezer does not freeze well. Causes most our food to get freezer burned. We tried turning it up and down but made no difference. Actually went and bought a separate freezer for meats.

Maytag washer Model #: MVWX655DW - I purchased this machine at Lowes in May of 2016. Always was a loud machine but seemed to work ok. In April 2018 the machine stopped working correctly. The spin cycle would lock up and not finish leaving clothes soaked. Called Lowes and waited for their repairman. He came and said it was the clutch and drive motor. Repair is over $400. Machine is worthless. Huge mistake. Never buy a Maytag. I called Maytag to see if they would warranty it. They basically said, Sorry only a one-year warranty on it. I told them the reason I bought it was it had 10-year warranty on it. They said only certain parts but its the drive motor that is clearly marked on the machine that has the 10-year warranty. I was told, No sorry. What huge waste of money. I am out close to $600 and Lowes only give you a store credit with their protection plan.The credit is not enough to purchase another machine without more out of pocket expenses. I will never buy another Maytag and I would not recommend anyone else does. Their warranty is a huge joke. Their customer service is terrible. Maytag should not even bother sticking the 10-year drive motor warranty on their machines. They do not honor it. My advice do not even consider buying one. You will be out the money and be purchasing a new machine within two years.

Purchased this machine to replace the recalled Samsung washer that was exploding. I should have kept my Samsung. I loved it and had no complaints, but since there were reports of it exploding I took the rebate and purchased the Maytag Bravo Nightmare. Everything you have read or will read here is true. I would spend hours, I mean hours trying to do a load of laundry. If the cycle would complete itself, the clothes would be soaking wet, and they never smelled clean. I would try rinsing again and the cycle would start out with 18 minutes and I would return to the machine 1 hour later and it would be still running water and still have 18 minutes or more left. I watched it complete the spin cycle and start the rinse cycle again. We had the service guy out several times - he would call the techs and they would test the machine and say nothing was wrong other than it was off balance. They said I was using the wrong detergent - when proving that I was using an HE detergent, they counseled me on how to lay the laundry into the machine, and said I was using too much laundry detergent. After babysitting this machine for more than a year, and being told by Lowes Customer Service that the techs say there is nothing wrong with the it, I was fed up. I called Lowes and told them to send their techs to my house to do the laundry. I threatened to call for service every week until my extended warranty was exhausted. They finally gave me a merchandise card valued worth the purchase of the machine. Now, I have the painful decision of deciding what to buy next - It wont be a Maytag!

Bravo XL - This is the worst washing machine I have ever purchased! Loved it at first but after a year or so we couldnt wash a full load without error messages. Then we couldnt even wash one pair of jeans without an error message. Called to have it repaired and $300. Later the bearing was replaced and the washer worked wonderfully once again. Less than a year later and we are back to having a non functional washer. Cannot wash anything without the error message. Customer service is absolutely no help. For such an expensive washer and supposedly a good brand, this machine is a real disappointment.

The Maytag Washer Model # MVWB835DW is the worst I have EVER had!! I have 6 kids, my husband and myself who I do laundry for and this was supposed to be a XL washer so I can do large loads! It does not do anything to stains and all my clothes come out with clumps of powder and if I use liquid it leaves greasy residue on them! Everyone in our home has had rashes from the washing powder not getting rinsed out and my husband who gets grease and oil on his clothes has all stained clothing because of this washer that does NOT clean anything! I used to be able to get every single grease and oil stain out until I purchased this washer! My 9 yr old now has a scalded skin from the washing powder not getting rinsed no matter how much I use!! I even tried using vinegar to make it dissolve and it does not help! No matter what we do it does not fill up nor wash the clothing properly!! This washer needs to be discontinued immediately and anyone who has it have the option of exchanging it with a better washer! It is absolutely ridiculous that they know this washer does this yet keep selling it!

I purchased a Maytag dryer several years ago, not a fancy one but just a plain simple dryer (model number MDE2706AYW). Thank goodness from the other complaints I have read I didn’t buy one that is computer controlled. The heating element has burned out twice, main thermostat and limit thermostat has burned out, and if you look close, it seems the wires are trying to melt or at least the insulation. Well, the insulation is melting. And the venting system is cleaned regularly so they can’t blame that. The last dryer I had lasted well over ten years with zero problems. I should have just fixed it. I’m sure I wouldn’t have spent as much money on repairs as I have with this one. You remember that lazy Maytag repairman that was on TV for so many years, you know why you don’t see him any longer? He is at my house repairing my ** dryer! You never, never hear me say this but the next dryer I buy will be made overseas. My last appliance purchase with any of these name brands on them: Maytag, Jenn-Air, Amana, Admiral, Crosley, Magic Chef, Performa by Maytag, and Norge.

The steam/heat produced by the oven has made the electronic (digital) control panel buckle. Yes! This is a thousand-dollar (plus) stove, and it has warped, through no fault of mine. When I want to cook something, I press the keypad to enter the number of cooking degrees that I want. The problem is, the control board is not working correctly. Regardless of my typing in 350, it will default to 100 degrees and stay at 100.As a teacher, I do not have a huge income. I was disgusted with my recent repair estimate of $80 for a service call, and a quote of over $600 for the replacement part, plus some not-yet-determined labor installation costs. Calling the 800 phone number for Maytag connected me to some local people working as independent and overpriced contractors in Los Angeles, California. They are not MAYTAG employees, so they are not well-informed about the product.I miss the time when manufacturers stood by their products, and had factory-trained and authorized employees available to make repairs. I bought this monster Maytag stove from Lowes. I am disgusted with both companies. I have gone online to research buying my own part and hiring a local yokel to put it in. Most everyone I have encountered has been a rip-off artist. I am teaching your kids and grand kids to read and write, and you dont want to help me repair my stove without price-gouging. I can use the burners to some stove-top cooking. Life has become a hassle without being able to cook.

I am very dissatisfied with this washer (Maytag Washer Bravos XL), it doesnt use enough water to cover the clothes. No matter which cycle you use, the clothes dont come clean. Who cares about water sensing if your laundry isnt clean. I will not buy another water sensing machine, I think the consumer should make that call on how full to fill the washer. Even on power wash the small agitator turns slowly. Not happy with this machine at all.

I absolutely love this Maytag Bravos XL washing machine... I bought this machine before doing any research because of a sale and then after reading multitudes of reviews... positive and negative... I thought I had made a mistake. The absolutely most important thing with this machine is to load it properly and select the proper wash cycles. You must stack your clothes around the outside of the drum leaving the center open. You must use HE detergent. This is a Commercial grade washer and is meant to be loaded. The twisting and wringing of clothes is because of the high speed nature of the spin cycle (commercial). If you have never been to a public laundromat then you should try it and see what those machines do to your clothes. I too was apprehensive about the water levels at first... So I stood there for an entire cycle multiple time and on diff settings.The machine is constantly adding water as needed and each time after about 10 min... no matter the size load I put in. The clothes eventually were covered by water. Have had no issues with clothes that come out dry in spots. I suspect this is due to improper loading. Again my info on using this machine... loading techniques etc.. all came from positive reviewers stressing the importance of these key factors. This machine was not designed or intended for light or delicate use. So if you do a lot of those type loads perhaps this machine is not for you. As for the loudness and banging I have read about I have not experienced that. I have read reviews that the problem in some case ended up being metal or plastic drip pans used under the machine. Mine sits on concrete. Anyway hope this helps someone out.

Maytag Bravos XL MVWB980BGO. To start, I live on an acreage so some problems may be related to being on well water. The most annoying part is the washer doesn’t have a drain & spin without rinse. So, when my well pump started acting up, I had no way to just drain & spin off the load, so I had to try to lift thoroughly soaked clothes and try to dry them...which took about four hours. Another aspect that is a pain is uneven loads. It keeps trying to fill, instead of just stopping & letting me adjust the load myself. Then the damn thing won’t reset. I often have to resort to unplugging the machine and starting over. High efficiency is a joke. I’ve had the machine about five years now and it goes low flow error, even though the flow is fine. I’ve tried running cleaners through the water line and it’s still doing the same thing. The only thing left to try is take the machine out and try and manually go through the lines. For the amount of money we spent on this machine, I am thoroughly disgusted with how it runs. It is the first & last Maytag washer that I will ever buy. Next time, I’m buying as cheap & basic a machine as I can buy. On the upside, the dryer works perfectly.

My washing machine is 2 1/2 years old. It is not overused, just 2 people in the household. Maytag wanted to sell me a contract for $320, I declined. After research I see that this machine has many complaints against it. I bought Maytag because they never need repair. I would like Maytag to fix this machine without charge or recall the machine. From what I have read, these machines are defective. The electronics are failing at 2 to 3 years.

The stove functions are excellent and the temperature of the burners and oven causes the food to cook even. However after about 6 months the heat from the burners causes the coating on the stovetop to burn like its baking and it cant be cleaned. Now the coating around the burners is horrible and burnt.

We purchased a Maytag refrigerator and right away had a loud noise. Found out the ice maker was on even though we dont have it hooked up. Now our freezer isnt working. Food is defrosting and ruined. Bottom half of refrigerator is freezing everything. Our fruit and pop and water and lettuce all frozen. 4th time they came which is today. Now says our freon is low so well see what happens. The repairman was so rude he was yelling. We said our Popsicles turned to slush so he said, Dont buy any. He was so nasty. No more Maytag for us – waste of money. Even had the compressor replaced. Wasted 1100.00.

The refrigerator is not keeping cold. The freezer is full of frost/ice. I had this fridge looked at twice in the past. Its about 6-7 years old.In the past, Maytag was considered a high end product. I wonder where the manufacturing is taking place for most of the parts. Could be it was cheaper to go overseas and now we are all paying for unacceptable products.I will never purchase Maytag. Maytag should be selling products they can stand behind! Products that are made in the USA, where our standards are higher and we expect products that work!

I will never buy a Maytag dishwasher again. I purchased it on 05/05/07 for $500.00. It’s quiet series 300 MDB6601AWQ. After 3 years of use, the control panel is completely dead. It was only working on one setting for the last year.

The ice maker in my Maytag French door refrigerator quit working 11 months after purchase. It was replaced under warranty, but again quit working 12 months later. That one was replaced at my cost, and lasted another year. It was again replaced at my expense and that lasted two years. I am now back to the dark ages of filling ice cube trays. I have been reading reviews, and find I am not the only one who has had problems. My letter to customer service was responded with a sorry about your luck letter. I would never purchase another Maytag appliance.

Original owner of $800 HE top loader washer since 2010. We heard a grinding noise for months, then finally it seized up. Repairman quoted me $300 to replace bearings. The repair guy seemed a bit too eager for the job, so I knew it must have been easier than expected. I Googled the heck out of it, and used this forum heavily for guidance. Seems the bearing failure is a pattern issue. It also seemed ridiculously involved and no one had posted a how to video matching my model’s layout. I took a peek with my own eyes and noticed a sock had gotten under the basket. The sock got caught in the drive belt and knocked everything loose. I removed the debris, tightened the pulley and everything worked. Cost me $0 to fix myself. So buyers beware before repair. And check the error codes yourself when in doubt! The first thing I did was check error codes. Found a great video here **.

I bought a Maytag washer and dryer at Lowe's when I bought my home-the price was great and I have not been disappointed in them-have had them over 3 years now. My washer has a stainless steel tup and is a top loader. The combo of the two was less than $1,000. The washing machine has deep clean, heavy load or light load, hot, warm or cool water settings, a hand wash setting and many other features that I think most consumers can appreciate.

My Daughter got me a Maytag oven with the AquaLift technology and is a piece of Junk. Half the time the Water is still there when the cycle is over. The water has made it between the front glass pieces and the finish on the top of the stove looks horrible, it just looks dirty. The knobs are cheap and the fake chrome finish is flaking off. Unfortunately Im stuck with it because I cant afford a new one... this was a gift to me because Im disabled and it was to make my life easier.

We received a MayTag Microwave on Saturday May 10, 2014. There was a minor ding in its case, but it did not show any other damage. After installation I tried to use the microwave. It did not work. So on Monday the 12th I called 800-688-9900 for service. A service appointment was scheduled for Wed May 14th. The service man told us the microwave could not be fixed and had to be replaced. I asked who should replace it. He told me to take it back to the place of purchase.I took it back to the dealer and after a lot of discussion it turned out that MayTag had to replace it. I was given a case number. I called Maytag and was told replacement could take 4 -3 weeks. I could purchase a new microwave and have it by Friday may 16th much sooner than Maytag could do.

Within 1 month Maytag sent 2 repairmen to repair my microwave. I paid $271.20 for the repair and part. The same 2 parts used the first 2 times were ordered again and I was told that Maytag could not get them again. The service and parts are supposed to be guaranteed for 3 months. Maytag refuses to refund me; offering me 15% off a new purchase. I would not buy from Maytag. They lost a customer.

I have called this company several times. Most of the time, they tell you that you need to call another department...which means you spend even more time on hold. This washing machine is only 3 years old. I will never buy another Maytag/Whirlpool product again!

I will never buy another Maytag product, and moreover, will tell everyone I possibly can, not to do so either. Like many others, I have a two-year-old dishwasher that needs a control board already, and from what Ive read this wont be the first time. It would cost $150 for the part, plus the service calls make it around a $350 experience. The only choice is to pull the machine out, or buy a 5-year warranty for another $318.56. Grand total for your marvelous high quality Maytag that lasts only 7 years? Around $1,000. I am so sad, the company used to symbolize quality but now when I see the logo, I think of landfills.

I bought my maytag stove model MGR7662WS on January 30, 2011 and have had it serviced 3 times... same problem. I set oven to 350 degrees, put food in oven and later check on food only to find the temperature reads 350 but the oven is cold. Food is not cooked and it smells like gas. I turn it off and turn it back on and it does not turn on most of the time. Service guy keeps replacing parts and says he will replace the same part he just replaced last week. He says sometimes the part comes out defective. I think the stove is defective and I have thrown away so much food because it does not finish cooking and smells like gas. Its so frustrating because my Thanksgiving was ruined two years in a row due to turkey not cooking.

My new Maytag washing machine does NOT CLEAN clothes or anything else. Waste of money. I have soft water, use bleach, hot water, Tide. I have even tried adding some baking soda. No use. I cannot wait until I can find a washing machine that works.

Absolutely the worst washer I’ve ever had! Do not buy this washer. Even after a double rinse there is white matter left all over everything! I’ve taken photographs of my laundry after two rinses and it’s disgusting. I will be quite happy to submit the photographs at any time.

I have a French door fridge Maytag like everyone else. The bottom freezes over and I have to de-ice it. Now the freezer doesnt want to cool. Its 3 years old. Total piece of junk.

I own a 2004 Neptune front end washer that Ive dealt with the terrible smell of stagnant water since I got it. Now the motor went and I was told I need a new washer even though the product warranty information clearly states the motor is covered for up to 10 years. The repairman told us that the motor thats in my machine is no longer being manufactured. How is that my fault? I do not have another $800.00 for a new one, which is now not even a lot of money for a washer. Ive already bought 2 washers since I built my home 14 years ago. Its just not right!

Maytag washer mvwc565fw: You have heard about how noisy they are & dont fill up enough water unless you set it on deep water wash. I cant get the right water temp. Its cold, cold warm. No hot at all. Sorry I ever bought the piece of junk. Only have had it a month too. The last washer I had it at least lasted 4 years. Wouldnt recommend it to my worst enemy.

I bought this machine a year and a half ago. The entire drum and spin motor need to be replaced. Maytags warranty only lasted 1 year. I bought it at Home Depot, and also purchased the extended 5 year warranty. The extended warranty is as bad as the washing machine. I am now just 2 days shy of 4 weeks of trying to deal with both parties. Ive had to take my laundry in to have it done. The cost of the laundry, the cost of the machine, and the cost of the warranty is more than $200 more than what Home Depots Extended Protection Plan is willing to reimburse/refund. Home Depot does as much as Maytag when it comes to standing behind what they sell. An $800 washing machine only good for 18 months, really???

Our Maytag refrigerator is leaking water all over my kitchen floor to the point that my floor tile has lifted. The ref. is a French door with water and ice in the door and freezer on the bottom. We have been cleaning up puddles of water at least several times a day. I see that this is not an isolated problem, as others have complained about this defect doing the same thing with their Maytag refs. Why hasnt ConsumerAffairs demanded a recall on these expensive defective refrigerators to date? I am truly disgusted.

I wrote the below to Maytag on their FaceBook page, of course havent heard anything back from them. Adding this on since I forgot about it, I have dogs and wash their blankets often, not that theyre dirty just for the dog smell. I have to wash them on the sanitize cycle which is an 1.5 hours long because if I use the normal cycle which is only 43 minutes they come out smelling exactly the same way they went in. I saw someone else post that their mothers front loader doesnt put in enough water so Im wondering if thats what happens to mine. So wish I would have checked the reviews before buying, thought I was getting a great washer buying Maytag.This is what I wrote on their FB page: I bought a Maytag front loading washer on 5/10/16 which was delivered and set up on 5/13/16. On Wednesday 10/19/16 it stopped working, so just over 5 months from the day it was installed. I called your company on 10/20/16 for repairs, they couldnt get here until today, 10/24, so 5 days with no washer. The customer service rep had all the details on what happened and Im sure passed them along to the repair company. He ran diagnostics, said it was the drain pump which was obvious even to me, but claimed to not have one with him even though they were in stock. Cant make it back until Wednesday, so two more days with no washer. He then proceeded to tell me that the dryer had to come off (stacked on top since the washer is a front loader) before he got back, that the warranty wouldnt cover two people coming out. So Im supposed to spend more money to hire someone to come out, take off the dryer and then pay them again to come back and put it back on. I called the customer service department again and was told they dont cover installation which stacking is. She said the warranty doesnt cover stacked units, as far as I can find that isnt stated in the warranty so please let me know where that is stated in writing. So I have a just over 5-month-old washer that needs repair already (bodes well for the future doesnt it??), will be without a washer for almost a week because the repairman didnt bring the most obvious part with him (maybe wanted to be paid for two calls?) and have to pay someone else for installation so it can be fixed. So wheres the Maytag man? I am not a happy customer and will be letting as many people know as possible. Ill be in the market for other new appliances soon, will sure as hell make sure theyre not made by Maytag, Whirlpool et all.

After only 3 yrs of normal 2 person family use my Maytag washing machine completely failed. The ball bearings in the transmission seized requiring the replacement of the transmission. At the same time the control panel failed yielding the machine completely unusable. The repair cost was more than originally payed for the machine, forcing me to purchase a new one (not a Maytag). Maytag said since there was no recall on this model that they could not help me. I bought the Maytag because of their claim of quality. This was not my experience either with the product, or the customer service.

We purchased a TOP of the line Maytag dishwasher with the expectation that we were also purchasing high quality. Boy, were we wrong. Continuous problems with the controls since out of warranty. The controls are in the door and operate pushbutton from top. This is electronic pushbutton not actual pushbuttons.MDB89595SBS.

We have owned the dryer (Maytag Bravos) since Dec. 2010 and are now on our 4th service call. Upon the second delivery of the part that was ordered last week - we will be on the 5th service call. I finally asked Maytag if I could get a trade in since this dryer is obviously crap. They said they could only handle the problem at hand, which is the same problem over and over and over. The flywheel was left off all together. The pulley belt for the dryer pops off about every 4 to 6 months. Ridiculous. Its a crap dryer, dont buy one!

My fiancee and I purchased a Maytag washing machine from our local Sears. We got it home and it worked fine, but after the first month it wasnt switching over from cycle to cycle. We called Sears and they stated that they didnt provide service to the washing machines, so we would have to call Maytag. We called Maytag and they sent servicemen from B & B Appliance to our home. We were told that they needed to order a piece and would be back at another time to fix the washing machine. They came back and said it was fixed. I went to start a load of laundry the following morning and the basement flooded. The hose had become dislodged when they were working on it. To add insult to injury, the washing machine was still broken. I called Maytag to request a different service company come to our home. Maytag said that they couldnt send a different company. They also couldnt replace our still broken washing machine and they could not accept a return. At this point we are out an almost $800 for the washing machine, over $5000 (which we have submitted to insurance) for the damage to our home, and almost $600 for a WORKING washing machine that was a different brand. We will never use Maytag ever again.

Maytag Bravo was making loud noise in the Spin cycle. Ordered new bearing, shaft and parts from Amazon. Also had to order the Bearing tool, cost more than the bearing parts. Total cost $145. Watch a youtube video on replacement, took about 3.5 hrs by myself. Biggest problem I had was lifting the washer up over the drain pan it is in. Washer is on the 2nd floor.

This is not a complaint but a love-letter. I know that todays Maytag Neptune is not the Maytag of old. But Im here to report that Im still using a Maytag washer that was built in 1982! The only thing wrong with my machine is that it occasionally goes off-balance when I wash heavy towels or blankets. Note: We inherited this machine with the purchase of a home in 1991. We were a family of 6, so this machine has done many heavy loads! Im looking forward to celebrating my Maytags 30th birthday, come Jan. 1, 2012. And I would love advice on how to replace it, eventually, with another machine that has just the basics - no bells and whistles, computerized control panels, etc.

I purchased this washer on 5-25-15. It was delivered on 6-2-15. It worked for 11 days. On the 13th, I called Maytag and made an appointment for it to be fixed. They said a technician would be out on the 16th to fix it. I got a call on the 15th saying the part they needed was not released yet so they would be out on the 23rd. The guy comes on the 23rd and diagnoses the problem. He says the machine has a bad motor and shock of all shocks. He doesnt have the part to repair it. They originally assumed it was something else and were wrong. Fantastic. He said he would be back on the 30th. I got a call on the 29th saying that, once again, the part needed to fix it was not released and that they would call me to make another appointment when it was available. I had enough. I originally purchased with Home Depot and called my original salesman. He told me he would replace the washer with any brand I wanted (I paid the difference in cost of course) but I was still relieved that he was willing to work with me. I ended up going with an LG. Lets hope that one works. I have 2 kids and have been having to go to the laundromat. I have to say that I loved the machine for the 11 days it worked! I would probably still have it if they had better customer service but Im not going to continue to put up with them not having whats needed to fix this thing.

I bought as a pair the Maytag Heavy Duty Washer and Gas Dryer 30+ years ago The pair are like a Timex watch --takes a licking and keeps on ticking. They have never failed me and I have never had to call the Maytag repairman.

This washing machine is good for cleaning clean clothes, like stuff you wear one day at a desk job. But nothing dirty. Its really bad. Dont fill it either, nothing will get clean. 1/2 full or less. If you put too much clothing in there it will leave lint and other debris all over them. Also, dont use granular detergent, it wont dissolve or rinse out. Liquid detergent only. Weve had it for about two years, and its a constant disappointment. A total waste of money. Really annoying. I have to get rid of it. Its almost completely useless.

You can not add water to the fill, blankets dont even get wet when you wash them, you can do double rinse but cant control the fill, have to sit there and lift the lid up and down for 20 minutes to get enough water in the machine! The washing machines have turned into absolute garbage! Wish I would have come here first, whats the difference if I control the load size water or IF I SELECT DOUBLE RINSE? THIS WASHER 200% GUARANTEED I WILL NEVER BUY A MAYTAG AGAIN. ABSOLUTE TRASH FOR $700.

Bought a 2400.00 refrigerator 1 year and 4 months ago. The freezer quit working and we lost everything in the freezer. We called and were out of warranty. The commercial on tv shows the bored repairman who never has any work because Maytag is so reliable. What a crock! We are going to have to pay for the labor which could be as high as 800.00. This is so wrong. This is a high end refrigerator and the fact that it only lasted a little over 1 year is unbelievable. I would dump it if I could afford to. It is a piece of junk. I will never ever buy Maytag again. Make a new commercial, one where the repairman is so busy he works 24/7. We got screwed by Maytag. They do not stand behind their product, they rob you blind.

Bought the Model MZD2766GEW and the MSD2454GRW side by side models of the Maytag side by side and the wide side by side from Home Depot in the year 2002 replacement appliances after a fire. For both units I paid $2526.92 dollars plus tax to put one in my kitchen and one in my basement. I was told by a plumber Maytag was the best, buy Maytag. It seems like from day one things went wrong. The ice maker kept building ice in the bottom of both freezers. The ice maker never worked right and would build up so much ice in the dispensing area, you would open the door and ice would fall all over the floor and you would have to take a knife to the shoot of the ice maker to unclog it. The drawers would freeze, the vegetables and anything in them, you had to keep the refrigerator temp to Zero and things would still freeze. Water eventually would leak all over the floor and I couldnt figure out where it was coming from. The freezers on the left but then water seem to be running to the right and out the refrigerator part. I couldnt afford to call anybody and the warranty was running out. I had 2 year parts and one year labor but at the time couldnt afford the service call charge. Eventually I was sent a recall notice for a compressor or such. I thought, Hurray, It will be fixed. Not at all. He replaced both those parts on both refrigerators and after he left it started leaking again. I called Maytag and they said, did he replace the part that was recalled? I said yes and they said They were not obligated to pay for anything past the recall. I should call and have the units serviced by a technician at my cost. If he says its the recall piece again, to call them back. Again I had no money to call a technician right away but when I did, he came to the house, told me it wasnt the recall and claimed to fix some kind of defrost sensor which cost $180.00 for the parts plus labor, plus service call and this had been a different technician than the first. He left and the problem continued to leak, freeze etc. In fact it seemed worse. I gave up calling and decided to deal with it hoping one day to replace but money problems happen and it is now 2014 I never could afford new refrigerators and have had to put up with the leak for all these years and continue to pick up and replace soaked towels everyday. In 2005 I disabled the ice maker which helped when I opened the door since ice doesnt fall out but both Refrigerators continue to make thick sheets of ice on the bottom and food is frozen into it so I cant use the bottom and when the buildup gets so bad it takes 2 days to defrost by shutting the entire unit off. All I can do is put my food in one freezer and refrigerator while the other defrosts. I also have turned the downstairs one off completely. Now as a second refrigerator I just dont trust keeping it on leaking also. I bought these units after a whole house fire and the last thing I want is another fire because Maytag just doesnt care but I cant afford new Refrigerators because these repairman and Maytag cant figure out whats wrong and fix the problem with this dangerous feature and I call it that because it seems to come with most of their units from when I bought the unit till now.12 years later people are still having the same problem with the same and copy cat units. Maytag, a plea goes out to you to recall and repair these units. The original recall did not work and like me a lot of people need to be redeemed for what you left go on and a lot of repairmen are ripping off people calling this problem what its not and stealing our money when you know what the problem is and can fix it. My plea is recall this problem or be responsible before God or who you believe in for letting it go on so long and the damage it may cost people. Maytag, people use to love you but youve ripped our hearts out and it will cost you in the long run.

We purchased a front-load Maytag washing machine (Model MHW3505FW1) two years ago this month. When the machine is empty, we always leave to door open. We dont allow clothes to stay in it for long, never for more than a day (the load is usually changed as soon as the cycle is over). Right now, the rubber seal on the front has tons of black mold on it, and when I lift the seal to look underneath, its way worse. There have been many problems like this reported on front-loaders. Wish Id known! Maytag will not send a replacement seal.

In December of 2013, I purchased a Middle of the Line Maytag Dishwasher model #MDB8949SBW for $600 plus $200.00 for install and removal of 5 yr old Kenmore. At that time I thought I did my research and saw no major negative flaws on this type of machine or similar machines. This replaced a 5 yr old low line Kenmore that just upped and died. Installed just before the holidays, this Maytag machine seemed to have worked tirelessly until a few days ago August 18/2015. The computer controls went haywire. I was hitting normal start buttons and other buttons on the other side of the control panel were blinking and lighting up. Worse was trying to cancel and the control boards were not responding. Even hitting the start button, the machine would not turn on. Finally looking at the facia, I see the tabs of the flexible plastic frame that hold the control panel popping out from underneath the white facia plate. Snapping the frame back in and applying a lot of pressure got the machine to operate. With a family of four and minimal storage space, this machine is used approx once a day. It appears over the year and 1/2 by pulling on the plastic handle - which also happens to be the computer control board frame, the computer has separated from its mount and has allowed moisture to hit the control board/computer and wreak havoc on the electronics. Looking up this model online NOW, I see I am not the only one with Dishwasher computers failing within a year or two- just out of the one year warranty. A Call to Maytags customer service has the computer control board alone cost $160.00 plus the service tech and his labor fees reaching in excess of $450.00. The CS rep gave me a repair discount to $267.00 and a week wait for the Service Tech for this problem to be fixed. I bought this machine on two premises - one for its price, it was the only machine that offered 3 spin jets that really do a good job in cleaning dishes and 2, I owned a 1984 Maytag dishwasher in another home with computer controls in the handle and to this day, that machine is still running flawlessly! My only issue with the 84 Maytag machine was after 4 years the door gasket went - too much soap - replaced and no issues since! I expected similar performance with this one. I guess I have to spend north of 3 bills for similar performance and quality. What was I thinking?

We purchased a high capacity washer (MVWB835DW), along with the matching dryer, two years ago from Lowes. This review is not about Lowes. They did the best they could to make things right. The review is about the Maytag washer (made and serviced by WhirIpool). It has been nothing short of a debacle. The first two washers did not work and had to be replaced. The third and current washer has been repaired three times, including the drum and motor. We have been without the use of the washer for over a week each time while waiting for parts and Whirlpool to approve the repair. The washer is not high capacity as advertised. Filling the drum even half way results in the washer stopping mid cycle whereupon we have to adjust the contents back into balance. In addition, the machine leaves a lint residue on dark clothing that has to be wiped off by hand. We have asked Maytag/Whirlpool to replace the machine but they say it has to fail for the same issue four times in order to qualify for replacement. We are done and will purchase another washer from a different manufacturer. It’s easy to understand why Samsung and LG have become such a dominate force in the laundry sector. Whirlpool/Maytag does not care about you or the problems with their product. Buyer beware!

Didnt even want to put 1 star but that is the lowest you can give. Maytag microwave less than a year old paid $350. Door clasp broke. Took two weeks to send a repairman out, he came out and of course did not have the part -- took another week to get it. Fixed the door and then he crashed and burned the microwave shorted it out and now it is totally dead. That was 2 1/2 weeks ago. Maytag refuses to replace the microwave and insists that the same incompetent service company come out and fix it. Meanwhile I have to call Maytag every other day to find out when the correct part to repair the microwave will be in. Was told it would be in two days ago. Never got a call to schedule the repair, called today to find out they never even ordered the part. Here goes another week without my microwave. Not only does Maytag have horrible customer service, they manage to find unskilled repair techs with equally horrible customer service! Will never ever buy another May useless Tag appliance again.

Purchased new Maytag washing machine July 17, 2011. Have had several problems with it over the past three years. Most of the time it would not complete a load of laundry and would get stuck before the drain and spin cycle. Last week, the spin cycle became extremely loud. Had a repair person come out and was told the motor bearings were bad. Estimated repair cost $700. Purchased this unit new for $569.00. Called Maytag, was told that 10-year warranty on drive motor and wash basket did NOT include the bearings. Asked if they could help out with repair cost, was told no. Will never purchase another Maytag product again as they do not stand behind their products. Household has 4 people in it so use of this machine was light to medium.

I bought this Maytag Dryer in May 23, 2015. I had nothing but problems. I had 4 techs come out and say different reasons why it does not work. I had the vent exhaust clean out. Still not working, the one tech said there was not enough clothes for the dryer to sense it wet. I did a huge load, still doesn’t work. The sensor for the vent keeps popping up and it’s cleaned. I have to pull it out and in to get the signal light out. Cant turn on the machine. It still does not work. I tried contacting Lowe’s, since I bought an additional services plan. They said I have to call every thirty days for three months. That means I have to take my time out of work and wait for a tech for three months to get make a complaint and TRY to get new one. I really disappointed with Maytag and Lowe’s. I have a tech coming out this Monday, 11/23/2015 for another services call. I will never buy at Lowe’s or Maytag again. How many times does a certified tech from Maytag have to come out check a brand new dryer?

It just keeps going. Still looks great. We have had our Maytag Neptune analog dryer for over 20 years. It has dried a usual 3 loads a day, with very little maintenance. We have replaced the motor, blower, and support rollers, but these are parts that were just wear and tear items, after years of extraordinary use. It has outlasted 3 or 4 washing machines.

I have a top load commercial tech washer with an agitator that is brand new as of September 2019. I have done all of the troubleshooting suggestions and nothing works. I use 1 tsp of liquid cold water detergent, deep fill, extra rinse, and clear liquid oxi and my darks still come out with white stains. I have had a Maytag tech check out the machine and it checks out without issues. I would never recommend this product to anyone!

The brackets that make the door open and close are just screwed Into the plastic lining with no kind of anchors. If you use the freezer a lot the screws come loose. Can’t close the door. And then 300 dollars later a service call. All to replace a screw. That’s just fine but the hole is stripped because no one could install a 50 cent anchor on installation at the factory. No more Maytag for me.

We purchased the Bravos X washing machine on Feb. 9, 2012. I had a Maytag for 30 years before this one and did not have any problems. My model # is MVWX700X. I have given it sufficient time to get used to it. I have tried all cycles for my whites and am not satisfied. I use Clorox in the receptacle and I have only used Tide HE. I spot treat all of our underwear, which is changed every day, and it always comes out unacceptable. I am so disappointed since I was so fond of my old one and only thought I wanted another Maytag. At this point, I would never recommend this machine.

We purchased a Bravo HE washer about a year ago after our old Maytag finally died after 17 years. Our new one is more quiet, does a good job with less water although the cycle times are a bit longer.

On 12/09/12, I purchased a Maytag washer, model mvwc200xw, from our local Menards store. About 6 months ago, the washer started making a slight banging noise, and would occasionally move in the spin cycle. Now, when washing a small to medium size load, the banging noise is very loud and does a lot of moving. I found nothing in the troubleshooting guide to help me on this, so I looked on-line and found several websites discussing this same problem. They stated that the problem was a snubber assembly and the replacement part would cost $4.55. They also said the washer would have to be taken apart to change out this $4.55 part.I watched a you-tube video of someone changing this part and quickly came to the conclusion that I would need help in doing this. A comment was left in the video from a Maytag repairman saying that the person changing this part was not doing it in a safe manner. The repairman stated that changing it in the way this person described in the video was DANGEROUS! I wrote an email to Maytag customer service explaining the problem and asked if there was anything they could do to help me on this 1 1/2 year old washer. I received an immediate email stating they would get back to me in 3 days. Ten days later, I finally received a reply. I was told there was nothing they could or would do even though I was a valued customer and that they understand and appreciate my feelings of disappointment.I worked for a large department store from 1970 to 1990 and sold appliances, one of them being the Maytag brand. At that time, they were considered to be a top of the line brand. This was why I purchased Maytag appliances for over 40 years. I am surprised and saddened to see a lot of on-line complaints against Maytag appliances and also that this 1 1/2 year washer needs to be repaired so soon. Obviously, times have changed. I figured it would cost me at least $100.00 to have this washer repaired. Rather than do that, I am going to take this in need of repair to a scrape recycling center and then go out and buy a new washer, but it will not be Maytag! Maytag will never disappoint me again!

Maytag Top Loading Washer-We bought this machine a little over a year ago and it is one of the worst products weve ever purchased. More often than not clothes barely get wet and then wad up into a twisted mess which stops the machine. Ive had to restart a load over and over. And, the clothes are not as clean as they were from our former Maytag washer which lasted 14 years. The new washer has to be cleaned at least once a month or it smells. We purchased this washer from HHGregg and they are no longer in business or I would complain to them about selling faulty products. I dont know why the manufacturer decided to remove the agitator from new models. What a mistake! We have decided to get rid of this washer and buy another brand. No more Maytag (or Whirlpool) products... ever!

Sounds wonderful. Thats what I thought when I let my son have my 20-year-old, still running older washer. I wanted a new one. It worked good for 3 years and then one night I went to throw the clothes in the dryer and its full of water. After the last rinse and spin, it filled again and stopped. So I tried it on every cycle and got the same results. I thought, No problem. We have a great, honest repairman. Ill call him the next day and hell fix it. When I called and told him what type of washer it was, he was surprised it was working at all. Seems they had a problem with water leaking into the transmission. Apparently, I was lucky that mine had worked for as long as it did. Like I said, Im lucky to have an honest repairman. He told me he could charge me to put in a new timer and solve that problem, but I shouldnt waste my money since it is just a matter of time before it goes bad. Seems they were all bad and Maytag never made good on them. Told me the smartest thing to do would just to go ahead, bite the bullet and get another. It will be here Tuesday morning. Hopefully, this will be the last one I have to buy (keeping my fingers crossed since I had hoped the Maytag was going to be the last). My old machine is still running great for my son. Over 30 years my repairman has had to fix quite a few things for me - ice makers, dishwashers and even a timer on my old washer. Thank goodness he was honest enough to not fix my washer. I dont know if there are even any Maytag products around now, but if there are, they will never get my business. I spent a fortune on a machine that should have lasted the rest of my life. Ive had childs toys that lasted longer. My advice is do not buy Maytag.

I bought my Maytag in 2013. It worked fine at first but for the last year it isnt getting clothes clean. In fact, some look like theyve never been washed. I have to run the rinse cycle 2-3 times and they still seem somewhat soapy. The washer still leaves clothes drippy after running the spin cycle. It takes 2-3 hours to complete a small load. I wish I had my old Kenmore back. It worked fine for nearly 20 years!

Maytag Bravos 300 Washer - Dont buy this washer! This expensive washer has been the worst household appliance Ive ever owned. We bought Maytag thinking we were getting the best. NOT SO! We could have spent half the money and got a better washer. Maytag is a brand of the past. Ive had this machine about 4 years and its been a problem since day 1. There is no soak cycle but I knew that from the beginning. The problems Ive had so far are: Not enough water so items dont get wet and have to wash again, Terrible wrinkles, torn sheets and garments, items still dirty, getting louder & louder, and the most recent problem is the plastic from the top edge of the tub is now shredding and getting sharp plastic pieces in my clothes.

We bought a Maytag refrigerator about 3 years and have had so much trouble. The freezer section which is on the bottom half leaks water periodically on the floor unless, we take the bottom rack out and pry the ice from the shelf about every week. It started doing this about 6 months ago and well need to get a repair man out here. The doors on the refrigerator are also a problem. They often dont close properly, so one is partially open, but unless you look directly at it, it isnt noticeable.

We purchased our Maytag through Sears. We wanted a very basic machine, and thats what we found at Sears, yay! Fast forward eight years and it suddenly quit agitating. We tried fixing it ourselves by replacing a plastic gear part, which, later on our appliance technician said was totally logical, but it still wouldnt work. We got our appliance repairman out here and he took it into the shop and fixed the problem, which turned out to be part of the motor or something like that. The thing that bothers me the most is that he asked if we had bought a refurbished washer, but we hadnt, it was brand new. He gave us a part that was swapped out that wasnt made for the machine and also said the safety guard for the cord was missing. This keeps it from pulling out of the machine in case it gets jerked. I feel deceived and just wanted to vent because there really isnt anything I can do about it now. Buyer beware, yes, but I know we have to be our own technician sleuths to be sure were getting what we paid for?

We are on our 2nd Bravos XL. The first washer lasted 6 years and there was a part going out that kept making it stop in the process. Basically the repair guy said it will just go out one day so it was up to us to repair or replace the machine. The machine didn’t have an agitator and we had been having issues with white residue on the clothes for a long time but thought it was related to the other part. So we bought a new one, with an agitator. It was the new model. We’ve had it around 6 months and we have lots of issues with the white residue. The only success we have with not getting white residue on darks is using deep fill and very little detergent. We use powder because the liquid makes dark spots on our dark clothes. So either way, there’s a problem. So we are using a lot of water when it’s supposed to be water saving. And we are using much less detergent that the company says. I think it’s the machine that has problems. I’ve read a long thread on Facebook and it appears that Maytag tells you to use Affresh regularly. It also says to follow their instructions. But everyone seems to follow instructions but Maytag takes no responsibility for their product. Makes me sad because Maytag was the best on the market at one time and we will never buy again. Our dryer works fine but the washer sucks. And that was a lot of money that I paid. I hope that Maytag decides to make it right and help their “customers” enjoy their products once again.

I bought a new Maytag dishwasher 9 months ago from Costco - Maytag 24 in. Built-in Dishwasher with PowerBlast Cycle, White. This dishwasher needs a new motor - Please do not buy this dishwasher. It is garbage.

MODEL: MFI2265XEM1 - ice maker dispenser leaked water while under warranty; took two separate technician trips to repair. Several months later, called Maytag regarding leak and ice at bottom. Technician replaced w/ grommet w/ larger dia drain tube extension; smaller dia causing backup of water & ice. Now, ice maker quit working completely, ice buildup in bottom part of refrigerator and freezer building up frost which means air is getting into the freezer, and yes, the freezer door is completely shut! Please advise if there is a class action suit. Will contact California Attorney Generals office.

My dishwasher was bought December 2013. The control panel just started going crazy and cant control anything. Unless you have bought extended warranty Maytag isnt doing anything. This is obviously a manufacture defect and no one is doing anything about it. Will no longer buy Maytag products if they cant stand behind their product.

I purchased this oven in April 2015. I have had nothing but problems with the unit. The temperature is off. I have had the probe replaced in July and will be done again next week (January 26, 2016). The AquaLift self-cleaning feature does not work. I ran the self-cleaning feature about 8 times and back to back on several occasions. The service providers stated that it really doesnt work and there is nothing they can do about it. The front of my oven, above the vent, is stained from the oven exhaust. They said there is nothing they can do about that either. The last service company that came out for a service call to check the oven temperature came without the proper tool to check the temperature and ended up snapping the propane line. I was given 6 month of a free extended warranty for my inconvenience and told that the company does not replace models. They will continue to come out and repair them. I will never buy another Maytag appliance again.

We purchased a bottom freezer refrigerator from the Home Depot in 2013 and I am sorry to say this refrigerator does not deserve any stars. Immediately after the warranty was up our refrigerator started leaking all over the floor. The drain clogged and freezes up on the bottom under the freezer. When it becomes full, it leaks all over my hardwood floor. I have now become a slave to this refrigerator. Each week I have to open the freezer and get down on my hands and knees to break up the ice, scoop it out, toss it in the sink. I have spread the word and I hope anyone who reads this does as well. Never buy a Maytag product because not only do they make defective products, they wont own up to it and recall it.

Horrible washing machine. Cannot get clothes clean. It simply does not supply enough water to wash. Have tried everything. I want my money back. How do you start a class action lawsuit. Thousands of people are dissatisfied also.

I recently bought a home that had a Maytag Neptune set. While they were newer than mine, I sold my Kenmore set, dirt cheap. Last night when I opened the washer door to take the load out, smoke billowed out. Im sick about this. There should be a recall on these washers!

Range is at least 20 years old and everything still works w/o issues. Our model has an upper level and a larger lower level that is a convection oven also. The top one heats up real fast which is great for quickly cooking and reheating. The lower one is large enough for everything else.

The performance of the refrigerator is disappointing. It was difficult to find someone to repair it when the freezer fan motor went out. It makes noise, shelf space is insufficient. Temperature mechanism often doesnt work properly.

Bought Maytag dishwasher 2007 at Lowes. Model mdbtt60aww-37837606ll manufactured in Benton harbor, Michigan. First got a recall that something was faulty, could cause fire, needed replacement. Took 2/3 weeks to get repaired. So couldnt use. Never quite cleaned good - many times had to rewash silverware, glasses. Never took off food unless very well rinsed. Today the control panel went. Called a local repair he said, Dont even fix. Toss and get a new one because its too costly to repair. I asked what should I get. He said no GE, they are getting out of appliances, no Samsung. Hes got whirlpool so guess Ill give that a try. In the past Ive had dishwashers 20 years, appliances 20 years. This junk lasts a year or two. Plastic cracks. None of these appliances are great anymore. Doesnt matter who you buy. Someone needs to get some quality control on what these companies are peddling .

Purchased top of the line Gemini oven a few years ago. Lower oven stopped working. Maytag repair said igniter not installed properly at factory. I contact Maytag customer service to see if they would help with repair cost. Rude response from them... basically saying anything fails after 12 months not our fault. Rejected my request without even asking details about product which model etc. Unilateral rejection. Horrible customer service. I will never purchase Maytag appliance again. Horrible, horrible, horrible. Avoid this company and their products. They do not a good product and they provide terrible customer service.

Bravos washer purchased Sept. 2016. I purchased the Maytag washer based on experience and reputation. I am so disappointed in this washer. I have had the control board replaced after only 3 months and it vibrates, shakes and is very noisy. It does not fill with enough water and the clothes are tangled at the end of the wash. I will never buy another Maytag.

In 2011, I purchased 2 Maytag dishwashers, one for my tenant and one for myself. In 2014, the circuit board on my tenants dishwasher failed, when the unit was only 3 years old and of course out of warranty. I first contacted a local repair person, and he informed me that the repair plus service would be close to $300. When I contacted the company, after about an hour on the phone, they agreed to send their authorized repair service person and after his evaluation, would repair the unit with no charge to me, as a courtesy. This whole process took about 2-3 weeks. I felt that was fair. It is now 2015, and my unit, which I purchased at the same time and the same type, now is not working due to a faulty circuit board. My tenant uses her dishwasher more frequently, and that is most likely why her circuit board went first. This is a design flaw, or perhaps planned obsolescence. At any rate, Im not happy with this, and my model is mdb7809awb2, and serial # is FO4205659. Do you know if there have been any other complaints on this? Thank you for your help.Updated on 07/30/2015: After I wrote my review, I contacted Maytag about the problem. After considerable wait times, I spoke to someone who set up a diagnostic repair call, giving me the impression that Maytag would cover it. When the repair company called, they told me that I would be charged $104.95 just for diagnostics. Labor and parts would be additional. I called Maytag again, and they agreed to let the repair company charge back the diagnostic fee. After diagnosing the problem, it was determined the problem was the control panel and not the circuit board. The cost to repair with tax came to $315.85 and it was only this low because the repair company waived the return service trip. I can get a new dishwasher for a little over $400.00. I am very disappointed in Maytag, because I remember the commercials where the Maytag repair man was bored because the products were so dependable they never broke. My unit is only 4 years old, and its sad that it costs so much to repair it.

Maytag has always been my choice with appliances. Ive purchased others and always dissatisfied. This dishwasher has been a trooper and lasted forever. Its been overworked with 4+ children and yet still going strong. I recommend Maytag????

I bought a Maytag front load washing machine. We paid $1,100 for this machine. About a month ago, it was making a loud noise. I called them and they said were going to come out and fix it. However, our washing machine did not have a serial number. It had the model number/purchase date, etc, but no serial number. Our drier had it, but not our washing machine. All Appliances stated they could not help us until we had a serial number. We spent around 3 hours on the phone with Maytag, trying to get a serial number. Melinda informed us that we were out of luck, and that there was nothing they could do for us. She stated to call Nebraska Furniture Mart, to get the serial number. We did. NFM does not keep serial numbers. They keep model numbers, and purchase dates, but not the serial number. I called Maytag back, and spoke with Arthur. Within 10 minutes, he gave me a serial number to use. Interesting. In the meantime, I have been without a washing machine for 2 days. I have a load of wash in the machine, because now the wash machine has gotten so bad it is shorting the breaker, and not allowing electricity to the machine. This caused the front door to lock and shut down. Inside the washing machine is a load of clothes. All Appliances now has the serial number to order the parts. The parts were supposed to be here yesterday, Jan. 9th. Surprise, they are on back order until Jan. 13th. I called Maytag to see what they could do regarding me without a washing machine for over 5 days, which could turn into 2 weeks. They simply replied that it takes time to order parts, and there is nothing they can do and apologized. I asked what about me having to go to a laundromat and sit for hours, doing laundry. What about sending me out a loaner, to do laundry until you can get the parts. They again replied; there is nothing they can do.I also stated I spent $1,100 for this front load top of the line, Maytag washing machine, because of its name, and supposedly good quality. They again said there was nothing they could do. They did tell me that the washing tub, the part that we needed, was on back order until January 28th. This puts me at about a month without a washing machine. They stated they would try and locate the part, and have it sent out to my house, not the appliance company that is supposed to fix it, but my house, so that once I did receive it, I could call All Appliances, and set up the time/fixing of the machine. This has been pure hell! Maytag is a joke. I paid a good price for a supposedly good company/machine. They are doing nothing to expedite the parts. They are doing nothing to back their products. They are not even offering compensation for my inconvenience of having to go to a laundromat, or being without a washing machine for over a week, and potentially up to a month.I have been without a washing machine for over a week. I have had a load of laundry locked in the washing machine. I have had to drive to a laundromat to do laundry, which includes time and mileage. I have been informed that the parts are on back order, and now could be up to a month without a washing machine. Maytag is not offering any compensation, no loaner machine, no replacement. Instead, they are just saying, sorry, you have to wait for the parts. I would really like the VPs. and Presidents of Maytag to go without a washing machine for a week, or their families to go without a washing machine for a week, possibly a month, and see what they have to say about that company.

I bought this Maytag dishwasher model # MDB7749SBM2 and of course it ran great until the warranty was up and then the touch pad started acting up where if you would press normal every other thing would light up. I replaced the keypad and then the controller and its working at this point again. The keypad ribbon cable had a big burn mark in it and by all these complaints it seems like an issue Maytag has and does not want to address. Luckily I work on electrical and was able to do this myself and I had no labor but over $300.00 in parts. What upsets me is I bought because of the reputation and the Made in America on it and it was replacing a 20 yr old Kenmore that was still working great when I took it out. With all the complaints about the same issue Maytag which is Whirlpool would step up to the plate and fix this. No more Maytags/Whirlpool for me again.

We bought a new Maytag Bravo washing machine last spring. It was easy to understand the instructions, but that is all that was good about it. Like everyone is saying. It doesnt wash the clothes completely. On every dark load I have what looks like streaks of lint. I contacted Maytag. They gave me suggestions for solutions. None of them worked. I have put the clothes on for a second rinse and spin and it got out some of the lint. Also. they are evidently spun so hard in the washer, after they come out of the dryer they are a wrinkled mess. All the wash and wear, which is almost everything we own, is wrinkled. I have to iron every item. Never again a Maytag for us. If there is a class action suit, I want in on it.

In July 2006, we purchased a Neptune Washer. The only problem we had with it is it does NOT spin the water out of the clothes after the wash cycle. This has been going on for about 4 years. In February 2012, we had a service person to examine the washer. According to the service person, there is nothing wrong with the washer. He said to put in clothing of the same type: All towels, all jeans, all pillowcases, etc. This is not the real world. This cost me a service call with no solution. On June 10, I called Maytag on my issues. They have no recalls or issues with this washer. They recommended another service call which I refused. I even offered the washer free of charge to the person I was talking to, but did not get a response. Never again will I purchase a product from this company.

Fridge model # MSF25D2EAB00. I have had the fridge 3 years and 2/3 shelves have crumbled to pieces, the compressor has gone, the ice bucket crumbled, the ice maker stopped working, once ice maker was fixed it got stuck on crush, and now I am trying to order another shelf because it has also crumbled like the rest and this is in a household of 1 person! I am just getting the run around... I have been redirected to 3 different numbers now (800-344-1274, 866-368-6478, and 877-468-2371) and now I had a rude customer service rep so I asked if I could speak with someone else and I am now on eternal rot on hold. Pretty sure he didnt even transfer me and Im just sitting on hold on his line while he is laughing. Time to hang up and try again another day. #un**believableI was also told that if I purchased the extended warranty plan that it would cover the crappy shelves in the future so I did and now they are telling me it doesnt cover them and it only gives me a discount on them. MAYTAG YOU OWE ME A NEW FRIDGE... THIS ONE IS A LEMON! I have no clue what my order number is or where my receipt is at the moment but I could get a copy Im sure because I purchased it on my HomeDepot credit card so if you want it let me know and I will provide it to you then.

We bought a new Whirlpool dishwasher, and it was a nightmare. So after four years of that we tried their sister company Maytags dishwasher. I have to say that I think these two old American brands have been ruined. This Maytag dishwasher is always making my dishes smell like rotten fish or a dead animal. I have to dump bleach and or vinegar down in the bottom constantly to keep the stink down. And I have looked and there is no food laying in the grinder. Then we started to lose wash cycles, and the buttons (not real buttons but a cheapo control panel) started to malfunction after 2 years. Now, 3 years into it the plastic adjusters in the top rack are broken, control panel has gone totally haywire, and still smells terrible. I remember when American appliances were sturdy and reliable because they were designed by engineers. Now they must be designed by accountants and shareholders. Goodbye Maytag and Whirlpool.

Bought new glass top Maytag electric range. Only used oven 7 or 8 times when I was unable to close the door. Had to wait 12 days for Maytag repairman. Has to order new parts. Still without use of oven. Says its a known problem the hinges holding the door arent strong enough. Last stove 24 years old. Never had a problem.

Like all of the other reviews, I have had this microwave less than two years and it won’t run and reads “door open”. I am filing with the Better Business Bureau as the product advertises “partS” under 10 year under warranty when in reality it is one part with a VERY limited warranty. In order to determine if my issue was covered under warranty I would need to pay $189 not including parts in labor. I called several times and customer service indicated that they had never heard of this issue (which upon looking at this site seems hard to believe) and I would need to gamble the $189 to see if it was covered. Terrible product, terrible customer service.

I have been Maytag customers for 40+ years. I purchased a new Maytag washer and dryer at Home Depot last year. The paint is coming off and the top is starting to rust. We have had Maytag washers and dryers for as much as 17 years that did not rust. The reason we bought Maytag was quality. Rusting in one year is not quality. Please contact us ASAP. Home Depot said there was nothing they could do.

I purchased a Maytag refrigerator (MBF2258XEB), stove (MER8674AB) and dishwasher (MDB7749SBB) on May 26, 2013. So far all three have been worked on. First, the dishwasher would not fill up with water after the trial run. Called the repairman out. A tag was placed in a position that was preventing the dishwasher from loading up with water. Granted, we should have taken the tag off, however, it stated not to. Lucky for me, I am still under warranty. Second, the refrigerator, which is a freezer at the bottom, started to leak. I thought that maybe we were dropping ice. However, I finally called and had the repairman back out. He knew exactly what the problem was because Maytag knew about it. There was a faulty plug. So in a matter of mins the problem was fixed. Lucky me still under warranty. Those two things happen within six months of purchasing these items. Now, the oven does not work. It heats up to the desire temperature but then cuts off. Called the repairman and he thought it might be the lower baking element. Unlucky for me, warranty has expired. So, $90.00 for service call. Received a called from the repairman, $120.00 for labor and $70.00 for the baking element. I purchased the baking element myself, $58.08 and installed it. Still does the same thing. Now I have another appointment for him to come back out and see what is wrong. Another $90.00! So far I have spent $238.08 on a $699.99 stove. I will never buy Maytag again. Depending on the amount to repair will depend on whether or not I go back to Sears and buy Kenmore. I had Kenmore for 10 years with no problems. I should have gone back to Sears for my upgrade. I did contact Maytag via email. I am still waiting for a reply. Live and learn!

We have had this washer for 1 year. I noticed right away my clothes would come out extremely wrinkled. Now not only are they wrinkled, they also smell musty. After researching I find others have the same issue, even finding a video of horrible mold under the drum. We called to have it serviced since we have a 5-year warranty. The service man recommended using Afresh. WELL, we do faithfully every month. He said they would not pay to have it cleaned, and even if he cleaned it, that the mold would come back. This to me is a major design flaw, one that could potentially make people sick. IF there is that much mold growing in the machine, with no way of cleaning it, and now the clothes are smelling, there is a HUGE issue!

I purchased a Maytag side-by-side, model MSD2656DEQ, in June 2000. First service call within a couple of months was for a very noisy ice dispenser, which the tech said was normal. Other than the noise, the dispenser has worked fine. Aug. 2005, the freezer frosted up and the tech replaced the defrost timer and defrost thermostat. May 2010, I had the same problem again and again these two parts were replaced. This morning, I found the food thawing in the freezer, 3 1/2 yrs since last repair. It is Sunday so will have to call tech tomorrow. Third repair in 13 years for a $1500 (2000 year dollars) Maytag. I have never had an appliance with so many problems and it was the most money I ever spent on an appliance. I am done buying Maytag products.

I bought this Maytag MCT washer and dryer set brand new from Lowes October 31st, 2016. When I washed the first load it made so much noise I thought it was broken. Called Lowes and they said it is just noisier than the older ones. This is the water/load sensing model, supposed to be great. I am usually here by myself, so at most I wash one load of clothes a week. I have a queen size mattress pad in there washing right now. This pad fills up the drum pretty much, I have it on deep water but that only gives me maybe 1/4 of the drum that has water in it. The pad is wet from wicking, NOT from the water covering it. How is this supposed to clean anything when the water is not covering the items?When it spins out, it gets off balance easily. The manual says to not worry about balancing load as you put it in there, but doesnt make any sense to just cram on one side as the water isnt going to float the cloth around to balance. The settings for Bulky does nothing more than the setting for Deep Water, you still do not get enough water to wash your clothes.It also does not do any good to add fabric softener to the machine, as it seems to just take it all out, you cannot smell any fabric softener on your laundry when you are transferring it to the dryer. And the laundry when dry isnt soft like it was with the old machines. I will be 62 in December 2017. My parents always had Maytags, never a problem. This is the 4th set of Maytags I have had. And bought a set for my daughter in 2013 also. And this by far is the worst. Their quality is completely gone now. Nothing but cheap made products that are predestined to fail. Friend across the street said she had looked at this set when she was in market to get a new set. She has an friend who works on appliances and who works for stores selling these models and he told her, they were not worth buying. Wish I had known that. Do not waste your money.

We have had washer/dryer Bravo Series and been nothing but horror stories. Washer bounces all over room to point hoses come out and flooded my laundry room and foyer and garage. It takes over 1hour 45 minutes to do loads sheets which is 2 sheets 2 pillowcases. The repair man told me that takes that long due to MY sheets are dirty. I have been married 46 years and never heard that ever!!! The dryer is just as bad, takes over hour and half to dry sheets and towels almost 2 hours to dry. DO NOT BUY MAYTAG ANYTHING. The person who said needed hurricane straps to hold washer is something I agree with. Just a horror.

My new fridge iced over top to bottom. It started making horrible noise then ice maker stopped working. Called MY repairman. Thats when I found out about all the ice. He told me to thaw out and hed be back. It thawed out and then freezer went out. ALL my freaking meats and frozen food had to be thrown out. Now water keeps Flowing out on my NEW tile! Called my repairman back. He came back then informed me it was junk! He said several other customers having same issue. My daughter has the same refrigerator and it broke down just like mine! My repairman also said a big issue with your junk was you used parts from other brands to fix!After reading all these complaints I can see no sense in calling to get it repaired. Its obvious we are all having the same issue. Maybe someone from your ** company could check them out. I dont have the money to buy another fridge! My 85 year old uncle with Alzheimers lives with me and I dont want him to slip on that water and hurt himself! I think all of these complaints need to go to BBB. Thats my next step. I believe you need to recall this junk or give us our money back! I need you to respond or Im going on blast to let everyone know how you treat your customers.

Wow, I bought a Maytag Bravo 300 series washer and dryer three years ago. They have been a complete piece of crap. I spent nearly $2k on the set at Home Depot. During that time, they have been serviced four times and I am now out of warranty and the washer is constantly breaking with LD and F51 errors. The heavy dryer door with light as hell hinges fell off on my wifes foot when she was loading it. I cannot get it back on. It is rigged so it will work. I contacted Maytag and they were not helpful at all. Pretty much sorry about your luck. I will never buy another Maytag product again. I agree with other posters. Too bad you cant chose zero stars!

I bought a Maytag dishwasher, stove and refrigerator and the dishwasher was a problem from the beginning. Repaired out twice and replaced the control panel. Seasonal residence, so the start of year 2 (this week) the control panel goes a third time. Its going to cost $387 to repair (told my elderly mother) and it turns out it was a warranty program that she purchased, not a repair estimate. She was misled as she called Maytag and they transferred her to a warranty company, and once again Maytag says theres nothing they will do. Now, Im hassled with cancelling that as well. I called Maytag and they dont stand behind their lemon of a product and said there is nothing they can do because its out of warranty (even though theyve been out twice to fix it). Do not buy a Maytag product. This is the first complaint Ive every written and I am just shocked that Maytag doesnt stand behind their product. Im informing 100s of people to not purchase Maytag and they will pass along my negative experience as well, for that, I am sure.

I purchased my first Maytag dishwasher and it was recalled as being a fire hazard. I was offered to have it repaired or pay for an upgrade (approximately $200). I chose to pay and upgrade because I dont want a fire hazard in my home. After my paid replacement, I received a recall on the new dishwasher regarding the same issue (different model) and I chose once again to pay and upgrade (thinking that if I spent $700, I wouldnt have a problem). In less than two months of installation, the dishwasher died in the middle of a cycle. Filled with water, I bailed it out and called Maytag. I told them that I wanted a new one and they told me that I was past the replacement period. They sent a service man out and he stated that it was a problem with model # MDB7709AWB2 and serial # F03002958. He said that it was easy to fix and said he had done it several times. So now, within less than 1 month before my warranty is expired, the dishwasher did the same thing--it died in the middle of the cycle and wont turn on. I called Maytag and they told me that they would send out a third party repair company (JD Appliance) but I would have to wait for four days. I contacted Maytag and said that I was concerned about the dishwasher breaking down again for the same problem (bi metal unit blew). This is the second time it happened. Jeremy, the repair man, said that the first replacement was not installed properly and they should have replaced the entire unit. He stated that it was a common problem with that model, as did the first repairman in Dec 2010. When I spoke to a supervisor named Kia at 800-344-1274, she stated that they had no known issues with this model. I said that it was not what the repairman told me as well as the Maytag dispatcher. They both said that the heat sensor (Bi Metal Thermal Unit Part No. W10258275) goes up and has to be replaced because it is overly sensitive. If you are out of warranty, it costs around $200 to have it fixed. I told Kia and she said that it was not documented in her file, therefore, it never happened. I want to know my consumer rights to address this issue. I have paid for (on 3 occasions) a new dishwasher and have continuous issues that cost me money. I want an assurance like an extended warranty, free of charge, for the dishwasher that has already been repaired twice for the same exact problem. I have the original part that was improperly replaced to prove that it wasnt replaced to specifications, therefore, blowing it again. I was told by Kia that Maytag does not compensate or replace their products unless deemed not repairable by the technician. It doesnt matter how many time the same problem occurs. I would appreciate your attention to this matter.