Good deal, recommended by dealer friend. Front loaders, high efficiency, 12 years or so. Finally needs new bearings on the washer. Replaced electronic board 5 years ago. High repair costs would be the worst which is related to low-quality construction. I expect my next pair to last as long as the last 1. Full size, not stackable but oversized drums. Relatively low water usage, lots of different settings for different loads for washing and drying, automatic water level and wrinkle guard.

We purchased this washer 3/25/15 for $873.77, we also got the matching dryer, for the same amount. This washer, never washed good, it is simply a bad design, I dont know, what type of mind altering products the designer was on at the time, but it must of been some good stuff, since all brands jumped on the wagon. This is a POS, I have contacted Maytag, and they just ignore me. We need a class action lawsuit against them, they think they can take our money, and laugh at us.

I purchased the Maytag metal interior two years ago, the very first year I had to replace the control panel board... Now, the panel went out again, after calling the Maytag executive office, they finally sent me the part, telling me I had to pay to get it fixed. That was just three months ago... Presently, the dishwasher has quit running water in the cycle... I will NEVER purchase another Maytag dishwasher... thinking you get The Best doesnt mean what you think... BEWARE...

Maytag washer, model# mvwp575gw0, which is under warranty. This washer is less than one year old. Within the first couple months the transmission leaked oil and service tech had to replace the transmission. A few months later – another problem, clothes wet after spin cycle - tech told me the agitator base and/or couple parts need replaced. Quality control appears to have been lacking at the factory when this washer was made. This house has only one person presently. The washer was not abused.

I have had it since 2011 and still works as good as it did back then. I love it. Hope it helps people decide when they go shopping for a dryer. I have a dog so I have to keep her clean so I wash a lot of her bedding and she sheds a lot. She also sleeps on the with me so that other bedding that I put for her on my bed between her clothes and mine which I do separate. The dryer works a lot and it is still going strong.

I HATE this washer. It had such good reviews before I bought it, but I have never been so disappointed. Doesnt use NEARLY enough water to get anything clean, even when I try deep water wash, bedding, or power wash. You cant switch modes in the middle of a load, and if you leave it paused too long, it drains on you. Ive tried balling everything up as the manufacturer advised. I tried using less detergent, again as advised. Nothing works. Sometimes the clothes on top dont even get wet. Dont waste your money!! If I can find a way to fix my old washer, Im going to do that and throw this thing to the junk heap.

I bought a Maytag Bravos Quiet Series 300 washer just over two years ago from Home Depot. The control board and sensor went out last week. The service technician seemed rather surprised that a newer machine would have that kind of non-wear-and-tear problem and suggested that I contact Maytag/Whirlpool to see if they could help offset the parts costs, as the repair was going to cost over $600! The customer service agent I spoke with said that there was nothing they could do because the item did not have an extended warranty. I explained to her that we purchased this unit, even though it was out of our price range, because we were told that it would last a lifetime. I would have been happy if it would have just lasted 5 years! She was very detached and it was clear that Maytag/Whirlpool was not going to stand behind their product. I will now take the repair money and go buy a new washer. You can be sure that it absolutely will not have the Maytag/Whirlpool brand!

This is my THIRD dishwasher, and by far the best. The Bosch machine I had before that was a catastrophe: mediocre cleaning, intense filter cleaning required - at least every two days - and, with a pretended noise level of 47 dB, MUCH noisier than the 50 dB announced by Maytag. Somebody is laughing at someone! To sum up: the Maytag MDB4949SHZ cleans dishes incredibly well, is very silent and requires no filter cleaning.

Zero should be a choice on overall experience. I purchased a Maytag Bravo 300 from Lowes in February of 2011. Last week I was doing a load of laundry and the washer stopped in mid-cycle, and it gave an alarm and error code ld. I checked out the manual and it said there was a problem with the drain line. I check the drain line and it was fine, so I called Maytag to have a service man take a look at it. Before he even looked at the washer, he said it was probably the pump, and it is not covered under warranty. And he said that it would cost $140. He obviously sees this all the time. He explained that the pump is too small for the unit and it does not allow anything to go through the pump. Please make sure anyone who may be considering buying one of these units knows right up front that they are going to have issues with the pump, even if a small pebble gets caught in the pump.

This is about my model MFI2569VEB2 refrigerator. It has French doors with bottom pull-out freezer, refrigerator door ice and filtered water dispenser. The delivery person installed the fridge and took off outside plastic and left inside plastic in. It froze everything until I took out the inside plastic. Within the first year, water started shooting out of the top of the fridge. A rubber connector for the icemaker, which was on top of the fridge, had broken. Within 18 months, it freezes everything in the refrigerator, even on the warmest setting. I have to leave it unplugged each night. The icemaker gets big chunks of ice stuck to it and wont let ice out. On top of all of that, the water from the fridge door pours out extremely slowly, this just how they are built.I will have to fix the thing myself and eat the expenses, so to speak. I bought the Maytag because Samsung had poor reviews. No matter how fancy you want your refrigerator to be, and how nice you want it to look in your kitchen, stick to the basics. The fewer bells and whistles, the more reliable.

My Maytag refrigerator was purchased from Home Depot less than 3 years ago. It is a French door, bottom freezer draw model #MFI2569VEA1. Every four days, there is a huge puddle of water at the base of the unit and it is starting to ruin my ceramic tiles. I tried the online video solutions to no avail. Home Depot wont repair it, they told me to contact Maytag. Maytag wants me to purchase a $375 warranty, which is 30% of what I paid for the refrigerator. I will never buy a Maytag refrigerator again, or any Maytag product for that matter. They once stood for solid reliability and peace of mind, now you get a piece of junk instead. I cant even sell it on Craigslist if I wanted to because who would want it? If a class action suit is ever initiated, Ill be on board. I hope Consumer Affairs contacts me.

We bought a new Maytag Bravo series thinking we were buying the best product... not! The washer has been running great. But when it came time to clean the washer on the Affresh cycle, the washer overflowed. It turns out the washer fills up higher on the Affresh cycle than it does on the regular wash cycles. Well, that’s why it overflowed; the plastic tub that hold the water had a freaking crack in it near the top! This washer isnt even 3 months old. I had to get a repairman in here once to check it out, then again to come back and fix it. At least it was under warranty. Im afraid what else will happen. Piece of crap Maytag, great quality checks! Maybe hire some real people that can see what the hell they are doing in quality. I told them about the damages to my basement. They sent me paperwork to fill out. Forget it, the paperwork gives you the runaround!

Maytag is the worst dryer ever purchased. We bought it in 2019 and the heating element broke. When I contacted Maytag directly, they said, nothing they could do. Really?? A major part was defected and there was nothing they could do! Its very sad when a major company that you purchased from shuts you down with a defected piece in their dryer and they chose not to help out the consumer. Shameful! I will NEVER purchase another product from them again...

Top loader Maytag Bravos type 588-03 - This washer is extremely slow and does a very poor job of cleaning. I use the recommended detergent (I use Tide HE) and follow the directions being careful not to overload. I can tolerate the slow operation I guess, but the poor cleaning is a real problem. When I put a plastic shower curtain in it, no clean happens. I just throw them out and but new every time. I will definitely go back to a Kenmore with an agitator.

Very dissatisfied with Maytag Washer Mod MVWB835DW0. This Large Capacity machine does not adequately clean a large capacity of clothes. In order to get a half decent wash performance from this machine, fill the machine only 1/4 full. Even using the recommended manual, I was very dissatisfied with the way my clothes looked after washing them with this machine. While I have been unhappy with the performance of this machine since purchasing it. What motivated me to leave this review is when my pants had the same sand debris on them after the wash as they had before the wash. I will be looking for a new machine this weekend. IT WILL HAVE AN AGITATOR TOWER!

MAYTAG HAS ALWAYS BEEN MY W&D MACHINES OF CHOICE! In my opinion they are the most reliable, dependable machines on the market - for years! I would NEVER by another brand of either washer and/or dryer.

I purchased this washer two years ago. It is supposed to be high efficiency so I was using cold water with the Water level sensor. The first load of dark clothes I washed came out with soap streaks all over them. This happened every time I washed dark clothes and sometimes they were barely wet. I emailed Maytag but they didn’t reply, so I called customer service and was told I should always use warm water and when washing dark clothes select a deep water wash. How is this HE?? When I wash towels or sheets everything comes out tangled and I am only putting in one set of queen size sheets. I will never buy another Maytag.

My brand new top of the line Maytag Bravo washing machine lid was broken and locked and would not open. I had clothes in there getting moldy. Three days in Pacific Sales trying to get help. The washer, of course, is under warranty (about 90 days). Finally a repairman came out from Appliance Doctor. He had no clue what he was doing. The company was rude. Then Maytag said High Tech was coming out yesterday, Monday, Dec 16, 2013 between 8 and noon. It never happened and when I called High Tech, he was rude and said it was not on his calendar.Maytag will not give my money back or a new machine or provide a competent repair company to fix it. I will be giving away the 1000.00 washing machine for someone else to fix and buying another brand. I would never buy Maytag anything after this experience. Please note, this is the first time I have ever complained to Consumer Affairs. Thank you for your time.

We have owned a number of dishwashers, some cost a great deal and some were inexpensive. Our current dishwasher is a Maytag and it has proven itself to be the best dishwasher we have ever owned, not only is it quiet, it cost less to operate and cleans all dishes and utensils excellently.

Maytag Bravos XL: I purchased mine Nov. 9 2017. I so wish I had never bought this machine! It leaves soap residue and dog hair on my clothes and bedding. I have to wash everything 2-4 times. It’s beyond disappointing. My husband and I agree our clothes looked better dirty, BEFORE we “washed” them in this machine.

I mistakenly purchased the Bravo XL top load washer. I only wish I could give it a zero rating. I have only tried to wash 3 loads of clothes. It is almost beyond belief that anyone could possibly think this could clean anything. My husband actually watched it “work”, and insists I call Maytag because they must have forgot a part! It does nothing but crumple/wad the middle items together and rub them...and only them...together. There is no movement of the outer items until it spins. Maybe Maytag should enlist people who actually do laundry to “test” the items they put their brand on. I know the government and the energy rules have added to the complex problem of buying something as simple as a washing machine...but this piece of junk is almost laughable to watch as it destroys your laundry. I’m almost embarrassed to let anyone know I bought it. Thankfully, I have 30 days in which to return it.

We purchased a Maytag Bravos X washer 2 years ago. Theres not enough water in there, and the clothes get so tangled that Ive had holes in them. Ive had technicians come out several times and they just say that its the water saving feature of the washer. I put it on the wrinkle control setting and the clothes come out ridiculously wrinkled. All of these problems are due to the water saving feature. I absolutely hate this washer and would never recommend it. I want my old washer back with the agitator and enough water in there to actually wash clothes.

I bought this washer less than 4 years ago and its already broken (leaking from the basket). Maytag refuses to honor their warranty and is charging $400 to send someone out to fix it even though it specifically says in the warranty that the basket is covered. When I mentioned this to the rep, I was told that does not apply to all washers. I expected better service from Maytag and thought it was a reputable company. I will now have to purchase another washer, rather than spend $400 to fix this one. It definitely will not be a Maytag!

I purchased a Maytag energy efficient dishwasher in June of 2010 along with an extended warranty that I keep extending. Cost $ but needed. Issue: Sensor in Panel fails so far every year and needs to be replaced. The repair technician showed me the sensor strip and indicated that this has been a big problem. (At least I have a warranty; however, it is a big pain to have to schedule a service repair person to fix the problem.) Repair (Sears) is EXCELLENT with great customer service. I did contact Maytag and there has been no recall.I own other Maytag appliances such as a washing machine and refrigerator with no issues there. In any case, I needed to replace my clothes dryer and did not select a Maytag. I purchased a GE very simple product with no sensor/bells and whistles. Not sure if I will go back to Maytag in the future - depends upon how they handle problems with their appliances. I would rather pay extra money for quality, durability, and reliability than go through the inconvenience from parts that are not made well enough to hold up.

My husband and I bought a set of Maytag appliance 12/2011 the washer squeaks real bad on spin cycle and now today the dryer started making real real bad squeak sounds to the point I can not use it!!! My appliances are only 4 years old!!! And we wash clothes once a week for just my husband and I. I would not recommend buying any Maytag appliances!!! They are supposed to be the best but are not worth **!!! And I called Maytag, they are not willing to help. Bad service!!!

We purchased a Maytag refrigerator in 2009. The freezer is on the bottom. In the last 3 months weve had to defrost this frost-free refrigerator. The freezer frosts and the refrigerator went into the danger level for foods. A technician said there is a tube from the freezer to the refrigerator that gets blocked with ice and your food is spoiled in no time. I wish I would have read this website before I purchased a Maytag. Hopefully, this will help someone else. I thought that Maytag was a quality name. That was the good ole days and now Im living in the good ole days defrosting a frost-free refrigerator. Beware!

After 9 months, the $850 Maytag Bravos started making extremely loud grinding noises during agitation cycle. We had 5 repair tech visits from A&E Repair, Maytags national repair vendor (and several cancellations + unscheduled visits by same). Each tech said a different part needed to be replaced requiring weeks of waiting for parts deliveries and getting huge boxes delivered to our office and dragging them home since my husband and I work for a living and are not home to accept large parcel deliveries. We had to unpack the washer basket in order to get it into our car and saw it was completely damaged. After 4 months of tech repair visits, using my home as a repair shop, forcing me to take days off from work and still no resolution to the problem, I was finally able to get Maytag to replace the machine. Our previous washer was original to our 25 year old house before it died. Unbelievably, the new Maytag has the very same problems and we are back on the same merry-go-round. This has become a part time job and super headache. I have never had such a horrible experience with a purchase or company. This is not a case of heavy usage either. We are ready to dump this machine! Do not buy a Maytag or affiliate product - Maytag is the worst!

My husband and I bought a Bravo XL washer in the fall of 2015. I certainly wish we had read the reviews on this site of this product. We would have saved ourselves a lot of money and grief. This machine does not clean clothes and actually damages them during the spin cycle as reported by others. This low water no agitator technology does not work on a top loader. Stuff doesnt come clean! Im not sure what we are going to do but we learned a valuable lesson the hard way. We purchased this machine in September of 2015 and are unhappy with it!

When I bought Maytag Neptune top-load washer, it lasted three months. I had to have the rockers replaced. Three months later, the lock switches went bad. Six months later, the main circuit board went out. Thank God it was under warranty. Ive had this ** washer four years and it broke down once again. I dont have any warranty and the money. They want to fix it. Im going to go out and buy something else. Piece of junk. It makes no sense. And when the first situation arose, I did ask if it had been recalled and of course, they said no.

Original owner of $800 HE top loader washer since 2010. We heard a grinding noise for months, then finally it seized up. Repairman quoted me $300 to replace bearings. The repair guy seemed a bit too eager for the job, so I knew it must have been easier than expected. I Googled the heck out of it, and used this forum heavily for guidance. Seems the bearing failure is a pattern issue. It also seemed ridiculously involved and no one had posted a how to video matching my model’s layout. I took a peek with my own eyes and noticed a sock had gotten under the basket. The sock got caught in the drive belt and knocked everything loose. I removed the debris, tightened the pulley and everything worked. Cost me $0 to fix myself. So buyers beware before repair. And check the error codes yourself when in doubt! The first thing I did was check error codes. Found a great video here **.

Maytag Bravos top load washing machine - This is the worst washing machine I have ever used. Like some of the other complaints it leaves lint on your clothing. It does not put enough water in the machine. The so called smart technology that senses your load does a terrible job. Your clothing is halfway out of the water, with dry spots, even after 10 minutes of agitation. I am constantly adding 3 to 5 gallons of water to my loads to get things in the water. And if I want to let thing soak for a while you have to unplug the machine, because after 10 minutes it will automatically drain the water out. 2 years of dissatisfaction. I cant wait for it to die. I should have come to this site first. Never buy a machine without an agitator!

Everything in my house is Maytag. I assumed they were the best. My dishwasher went out after three years, and I replaced it with a Maytag. Now, my over the range microwave is not working. I will not replace it with Maytag. I expect my washer and dryer to be next.

I purchased a Maytag Washer and Dryer about 3 years ago, they were under warranty for two years. Two years and 10 later the dryer breaks down, repair 310.00, two months later the washer breaks down again, 331.00, while I’m waiting for repair appointment the dryer breaks down, 130.00. Then I’m finally able to do laundry, turn on the washer for the first time since paying 331.00 and IT DOESNT WORK AGAIN, another SEVICE CALL!!! $$$ IM EXTREMELY DISAPPOINTED IN MAYTAG, ESPECIALLY AFTER VIEWING YOUR COMMERCIALS!!!

I bought the Maytag MVWX700XL1 (Bravos X) model in 2012 from Home Depot. I paid over $800 for this washer. I knew I was in trouble when I found dry spots on clothes after the washing completed. I started using the Bulky cycle. So much for saving water. It has not been overused, its only two of us. Today the spin cycle sounds like a train. The washing cycle has stopped working completely. Im very dissatisfied with this washer.

I bought a Maytag front loader washer and dryer, plus the pedestals for each. In last August of this year the washer just stopped in the middle of a wash cycle. I placed a call to the customer service. The tech diagnosed and placed an order for a part and set an appointment for two weeks later, with a time window 1 to 5 pm. The person called at 5:30 to tell me he had an job before he could get to me. I had taken the day off to wait for him. I called and they ended up rescheduling, for two more weeks.. Tech came ordered different parts, tech did not show up. Tech came out again ordered new parts. Next week he arrived wrong parts. Washer still not extracting. New tech, new parts, new appointment, this was what happened throughout September and October. Tech was not happy with his job, stated that to me, would not do anything but install part, even if it didnt work. He took parts with him. The washer still not extracting. Last Thursday he didnt even have all the parts, made the decision to replace machine without discussing it with me. Told me Sears would call me in 48 hours. Received call today Tuesday. Go to Sears to have it replaced. None of the machines they offered are compatible with mine. I will have to purchase the pedestal for the new machine, plus pay the overage to get the comparable machine. Service appointment people were horrible, cold and rude. Sear store at the mall where I purchased my washer said that it was not their problem. Once we sell it you are in their hands. Have had Maytag for over 30 years. Will never buy it again. Will never buy at Sears again. Too bad I have to replace my washer with something from Sears. Not enough space to write everything I have gone through, the lost workdays, the extra expense of having to go to the laundromat, the stress of dealing with incompetent people and techs.

Absolutely the worst washer I’ve ever had! Do not buy this washer. Even after a double rinse there is white matter left all over everything! I’ve taken photographs of my laundry after two rinses and it’s disgusting. I will be quite happy to submit the photographs at any time.

I purchased a Maytag Bravo Washer and Dryer about 2 years ago; dissatisfied with the products. Washer continues to smell. I clean it all the time with the Affresh tablets. Usually, I have to use 2 bags just to get it not to smell for at least 2 weeks. Now, the glass front dryer is rusting out around the window.

Just got a Bravos Maytag commercial washer. Washed two throw blankets and the washer has a see-through window on top, and I could see that the blankets didnt move on top. How are clothes supposed to get clean if they dont move? It also took an hour and a half for one load. What you are saving on water you are wasting on electricity. I personally dont like them for those reasons. I appreciate the company in my town (little known), they let me return and get the old agitator type with NO sensors. Just love the agitator, might wear on clothes a little more but at least I know theyre clean!

In a way, l feel fortunate and you will read why in a minute. l have been reading Maytag complaints specifically looking to see if what happened to me has happened to others. Apparently, it has. We purchased our Maytag range, model MER57750AB, in 2005. We too have had some repairs done under warranty. Unfortunately, we live in a day and age where technology isnt always our friend. The old appliances that were not electronically driven lasted forever; todays appliances do not. However, when something with potentially serious consequences happens that is not technology related, it rates in the who is the idiot who designed that? category. I am talking about the exploding exterior glass oven doors.Two weeks ago, the oven door handle on our range came unscrewed on one side. I continued using the appliance, planning on repairing it myself when l found the time. (I used to tinker around the garage with my dad when I was little and therefore, I have great repair skills in several areas.) Last week, I was standing in front of the stove when all of a sudden, the glass panel dropped from the door! It landed straight up on the floor and fell forward so the top edge of the glass landed on my toes (the toes that I had surgery on for six hammertoes last November and are still sore!). Needless to say, l was shocked that this happened, and even more so, I was grateful that it did not break or either of my two grandbabies were around at the time. Then, I looked at the glass and saw that it was attached to the door using only eight small pieces of double sided sticky mounting foam. I mean small! As I said before, idiot! Did they not think that the heat from the oven would eventually wear out the ability of the tape to do its job? I gave up reading after I found enough complaints about the mishaps with the glass on the oven doors to realize that there is a definite problem here. I did not see where the glass fell intact, as mine did. Therefore, I am suggesting that the exploding glass panels more than likely gave way, as mine did, and shattered when they hit the floor. Should there be a product recall for this? Absolutely! The question is how does a recall get put in motion? As others have stated, this could have been a horrible disaster had little ones been around. I pray that doesnt happen to anyone.

It is not worth the money. I paid $2500.00 for a Maytag refrigerator that I had for two months. Two service calls were made to Maytag as of 07/07/2014, the problem no ice and the refrigerator stays warm. The problem has not been resolve and Maytag refuses to replace the item.

Purchased the Neptune washer & dryer in 2002. Did not purchase any additional warranty. I have had Frigidaire, Kenmore and Speed Queen washers previously and used them until they quit. I have not had any problems with either the washer or dryer. No mold, no smell, nothing. I did laundry for 2 children and 2 adults, 6 to 8 loads per week with half being heavily soiled work clothes. I still wash 3-4 times a week. I was able to wash & dry king size blankets and comforters for the first time with this set. Washer and dryer are located on the main floor of house and are the quietest units I have ever owned. They may quit tomorrow, but they have done the job that they were designed to do. I am well satisfied with the quality and performance of both units and would not hesitate to purchase Maytag appliances again.

My Maytag dishwasher model MDB7749SBM2 was two months out of one year warranty and the Whirlpool control panel went out. We replaced it for 80.00. 3 months later same issue. We had that replaced for free. 4 months later same issue. We had to fight but got that replaced for free. Now 2 months later same problem. It cleaned wonderful when it worked. I will never buy another Maytag or Whirlpool. I used to buy nothing but Maytag. We threw it out tonight. Tired of a dishwasher that is only part time.

I purchased a Maytag dishwasher (Model MDB7809AWWI) in Sept. of 2009. In 2010 and 2011, it had dead control panels. The first time, it was under warranty. The second time, it was not, and I purchased a costly service plan to have it repaired. Now, 2012, its dead a third time. Maytag tried to tell me that I could purchase another plan for $289. I informed them that for that cost, I can replace it with a dishwasher that doesnt require costly service plans and yearly repairs. They informed me that their parts only have a 30-day warranty. If theyre not willing to stand behind their products enough to admit that one is faulty, then Im not willing to stand behind them as a company.

Purchased the Maytag MMV405DS Microwave and matching refrigerator from Best Buy in 2016, they were exactly what we had been looking for. Little did we know of the problems we would have with the microwave. At the one year mark the infamous open/close door problem begin. Luckily we were still within the warranty period since it was repaired at no charge. However six month later the problem re-occurred, we are now out of warranty and have little recourse. Maytag should have by now have come up with a fix. I find it hard to believe they are still manufacturing this microwave and selling this product knowing it will fail. We have little choice but to replace it with another brand which will not match. Suggest anyone looking for appliances stay away from Maytag.

I purchased a Maytag refrigerator from Home Depot 2 years ago and the first year I already had problems. The second year there was ice on the bottom freezer I called Maytag. They claim a technician needs to come out but cant tell me how much it is to come out for an estimate. After they come out they tell me how much it was. Everyday I have ice or water from the freezer. I had also purchased my stove which very easily has been all scratched and considering that I hardly ever cook, I figured it would look new for years. I will never buy another Maytag appliance!!!

When my husband surprised me with a double oven stove I was leery. First Thanksgiving my thoughts were concurred as the 20lb turkey fell from the chinsey rack.....even a cookie tray with almonds fell down.... Unfortunately the lower oven is off by 1/2, no racks work in there. My biggest gripe is that the seller did not exchange it, just tried more racks. Now Maytag will not do anything but allow me to order more racks. This item is a huge piece of junk.

I love this washer. You can fill all the way or energy setting but either way it does the job. I paid 1200 for a Whirlpool. it was broken within 6 moand couldnt get service repair. With the Maytag it was on sale for 550 cash. It stop spinning. I called for service. They were there in 2 days on time and 20 minutes it was working. It was a needle stopped it. Just reprogrammed and wa-lah!

Maytag Maxima 9000 washer not working since day 1: I have placed a call on Friday, June 14, about my Maytag washer not working. The service man came in on Friday, June 15, 2012, and stated that a UI board needs to be replaced. I have called Whirlpool to ask for the part to be ordered so it is faster, could not do anything. Then, I have not heard from Whirlpool since. I called them again on Wednesday, June 20th, and I was told that the part was ordered and it will take up to 10 days for it to arrive. Once it arrives, the technician will call to set up an appointment. So, according to Maytag (Whirlpool), I can be without a washer for at least 2 weeks (as 10 days are 10 business days) and it is all good.

The freezer will frost up and the shelves will not move. Repairman has been out three times, once to clean the drain. The second time he installed new tracks for 250.00. Two hours later they still wont move. The third time out he said it was repaired, but two hours later they didnt move again. We are very disappointed with Maytag.

13 months after purchasing MDB7749SBM3 dishwasher this lights started making no sense. For me the buttons still work, but it seems like only a matter of time until they stop working too. Like many others, I opened up the door and found the corroded ribbon connector (see photo). It wasnt damp so since the corrosion happened at the point where a ridge of plastic presses the ribbon against the hot handle, I suspect heat. Obviously a design flaw. Come on Maytag. Recall?

Maytag MVW823OHC SLATE washing machine, $1050 plus warranty $169.95 on 05/27/21 not delivered until 06/25/21, error code on 09/19/21. It is 11/03/21, machine is not working and no part available. Sad.

My Maytag (MER7662XQ) oven has stopped working after barely 6 months of use. I filed a warranty-repair complaint and reported the error codes shown: F1 (faulty touchpad) and F3 (faulty temp sensor). Although Maytag promptly sent a repairman, he arrived without parts and left within 5 minutes without fixing anything. He said he would order parts. Whenever they were delivered to us, by mail, we should call again to schedule another repair. But he warned he was prohibited from coming out for another 7 days. So far, Ive been without an oven for almost 3 weeks and there has been no action or information. My calls to Maytag produced nothing, except confirmation they show the repair as open since they do not actually distribute parts, and the repairman is with an outside company. A terrible product and a worse service! I would not ever buy another Maytag product and recommend that no one else does either.

Model MDB4949SDZ0. 7/10/2018 Purchased from Costco. 7/23/2018 Installed by company arranged by Costco. 6/18/2019 A burning smell was coming from front control panel area of dishwasher when it was turned on. 6/25/2019 & 7/3/2019 Repair technician came to fix but could not find anything wrong so burning smell continued whenever dishwasher was one hour into cycle. 7/12/2019 Repair tech changed out front control panel because burning smell was still coming from handle area. 8/9/2019 Dishwasher does not drain completely when wash cycle is complete. Sometimes there is sudsy water left, sometimes it is clear. The water level is above the heating element at bottom of dishwasher.We only run the machine 2-3 times a week and have been using different cycles to see if the draining issue is with one cycle or all of them. No matter which cycle is used, water remains at the bottom of the dishwasher above the heating element. This seems like way too much residual water. Repair technician is scheduled to come for the 4th time to look at dishwasher but we just received a message that we will have to pay $129 service fee because dishwasher is now out of warranty. Maytag, fool me once, shame on you. Fool me twice, shame on me. Therefore, know that we will not be purchasing a Maytag product ever again.

They are coming for the 7th time to fix the ice maker. Three full replacements. The bottom of the freezer had a buildup of ice, another call to repair. I know where the Maytag repairman is, hes at my house.

Washer is noisy and water does not saturate clothes on normal wash. Have to use sheet setting for small or large load. Washer changes gears and it is so loud and clanks like something is falling apart.

I bought the Maytag Bravos XL 5.3 washer because it was advertised to conserve water and it was a good brand, but it was a horrible mistake to buy this washer. The washer barely uses any water to clean properly and it hardly moves any of the clothing. The only thing that does move is the clothes at the bottom while the clothes on the top stays still. After using it for a day, I decided to return it back to Home Depot where I bought it, but they did not accept it and told me to call Maytag to return it. I called and the person who answered gave me different numbers to call. After going through ten different numbers, I finally received someone that could help me and they told me that I could not return the washer. They told me that the only way to return it was if there was a mechanical problem with the washer. It is extremely frustrating because I paid over $800 on this washer and now Im stuck with this garbage because I cant return it. I recommend everyone to not buy this washer otherwise youll get the same problems I am getting. I have to manually stop the washer and move the clothes by hand.

Maytag Dishwasher MDB7749SBW03 - We purchased this dishwasher in 2013. About 1.5 years after purchase the control panel started to get flaky and different settings wouldnt work. Not long after that it stopped working at all. I did some troubleshooting and found that the ribbon cable that connects the control panel to the control board was corroded due to water/steam getting to it. Since we were past the one year warranty I bought a new control panel and things worked fine for about a year, now the panel is going bad again. I contacted Maytag and they said they cant do anything to help me. This machine is not even 3 years old and going on its second control panel. I would recommend staying away from all Maytag products.

Horrible machine. Purchased on 02/28/2014. I am 63 y/o retired housewife now. Machine used only for light washing, occasional king size sheets and weekly towels. I bought into the Maytag name, am so very angry that I did. Started a load at 1215 pm today... it is still sensing, washing, rinsing, spinning and then it starts all over again. Just unplugged from the power source, hopefully I can get the clothes spun out enough to dry!! Call and live chats to Maytag were frustrating to say the least. $400 plus Maytag service call to check out the machine not fix check out repairing would be extra. (I do not live in rural area, live 5 minutes from downtown Jacksonville FL!!!) Independent Repairmen will not touch this Maytag Model (cannot say I blame them!!). DO NOT PURCHASE A MAYTAG PRODUCT. This is a horrible company lacking in integrity, honesty and fairness. They sell shoddy, inferior products based upon past history.

DO NOT BUY THIS MAYTAG REFRIGERATOR. Purchased 9-30-19. Delivered 10-4-19. 12-9-19 - Not Cooling, Called Whirlpool on hold for exactly 1 hour. 12-11-19 - Repair service here - ordered new Control Panel. 12-17-19 - New Control Panel Replaced. 1-6-20 - Freezer is not freezing. Control Panel going up and down and blinking constantly. Called Whirlpool - on hold for exactly 1 hour. They called service repair. 1-8-20 - Service Repair here and ordered 2 thermostats: 1 for freezer and 1 for refrigerator. 1-15-20 - Service Repair here to install 2 thermostats - At this time I purchased the extended warranty for $119.30 for 3 years.3-1-21 - Control Panel completely went out again. I called Whirlpool - on hold exactly 1 hour before they answer phone. I am so pissed. They call Service Repair. 3-3-21 - Service Repair here. They order new Control Panel. States these panels are continuously going out and they are having to replace them everywhere. 3-12-21 - I called Service Repair since we havent heard anything. ETA on control panel from Whirlpool is not scheduled until 3-19. I am really pissed by now.In the meantime I have been on hold with Whirlpool for 47 minutes. At exactly 1 hour being on hold, they answer my call. Im told I have to wait. There is nothing they can do. I told her we were buying ice every other day at $10.07 for 2 20# bags and they wont replace money. Told me to throw my items away and they would replace all the food for $250.00 one time during the 3 year contract period. The service is Customer service on their contract is terrible. Waiting for parts is even worse. This is a piece of crap appliance and we will never buy another Maytag.

I purchased a Maytag refrigerator, stove, dishwasher and microwave in 2006. Like another commenter, I also insisted on all Maytag appliances. What a huge disappointment. About four months into owning the microwave, a computer module had to be replaced. The microwave stopped working about six weeks out of warranty. It just stopped working, period. I was told by Maytag that they consider microwave a disposable product and they would not cover the repairs. It was cheaper to buy a new one than repair the old one so I replaced it with another brand. The dishwasher failed after 4.5 years (would not drain) and again it was cheaper to replace it than fix it. The oven range handle broke off (normal use) in August 2011 and that cost me approximately $200 for the part and the service call. The refrigerator has had two service calls for the ice maker to replace the motor. The first was covered by Maytag, the second by me. This occurred when the unit was approximately three years old. In August 2011, I had another $90 repair because the ice maker drain (?) was plugged and had to be cleared fixed. I have never been able to pay what I paid for these appliances. Prior to this, we always purchased a middle-range appliance and we never had problems like this.I will never purchase another Maytag product again. This is so disappointing. I live in MI and I wanted to support a MI business. Unfortunately, I wont be able to help out this particular company any longer. Dont buy Maytag appliances. It is a waste of money.

This machine (Top-Loading High Efficiency MVWB755DWO) does not clean, it only leaves soap and moldy residue on clothes. The Whirlpool company refuses to assist even though it was delivered less than a year ago. So much for warranties! Wrinkles clothes, wrings incorrectly and does not give you freedom to manage independent of technological controls.

We bought a Maytag Centennial Washer in 2011. 6 months ago the control board went bad. Maytag has an exorbitant replacement price! I went to Ebay and bought a NEW board for 1/7th of the price Maytag wanted. The old board was marked revision B. The new board is revision F! That indicates to me that the board was defective when it was new and they have made 5 attempts since then to fix it! No recalls however. Now the motor is shot. I found out the motor from Australia is also inferior! So this 5 year 3 month old POS Maytag is going to the dump! We will shop for something made outside the US. No not a Samsung. I think there should be a class action suit against Maytag.

I bought a Maytag dishwasher (model MDBH945AWB3) in March 27, 2010 to replace a Kitchen Aid dishwasher that was only six years old and no longer serviceable. After a little over a year, its dead. When I try to turn it on, nothing happens. If I press the delay button, the lights come on, but in about a minute, they go off.

I purchased this washer because of Maytags reputation of the repairman who was supposed to be needed less. Ha! Was that a joke? Ive only had this washer 5 years, repaired once and now it sounds like its gonna blow up. Please dont buy one… Maytag has a one year warranty, but unfortunately I didnt take one out due to their reputation. Plus its hard on the working class to come up with the extra for the extended warranty! I dont normally write reviews but thought maybe I could save someone else a little cash!

My refrigerator is a lemon! We bought a Maytag bottom freezer French door refrigerator model #MFD2561HEW in May of 2007. Less than a year later, it stopped working and ruined all the food inside. I cant remember the problem that time, but it was fixed by Maytag and we were reimbursed for a portion of the food we lost. Two years later, the temperature got warm in the refrigerator and freezer sections, and we were gone for a couple of days, so when we got home, all of our food was spoiled. This time we had an extended warranty in effect and they replaced a circuit board, but we were out the food. A few months later, the same thing happened. This time we were home and saved most of the food. The compressor was replaced, again under warranty, but it took 2 weeks to get the part. Now, less than a year later, the freezer and refrigerator compartments are getting too warm and frost is forming in the back of the freezer. When it finally does get cool, it freezes the food in the refrigerator section. It also makes loud bumping sounds. I paid $80 to a repairman today to tell me that theres nothing wrong with it, thats just the way it runs! He suggested I put a gallon of milk jugs filled with water in the freezer to hold the temperature when it starts to rise! This piece of junk is just 5 years old! When I complained, I was told to call Maytag and discuss it with them. This refrigerator was not cheap and I see that many others have had similar problems. How do they get away with selling an inferior product?

After a year or so my Maytag fridge is leaking, I followed instructions on how to remove ice clogging the drain pipe and fixed the problem. I see that this problem is going to repeat over and over again for the life of this unit, because of a poor design.The design fix will be to add a small heater (at the location where the ice creates the clog) actuated periodically by the control board, or at least with a manual push button for the user can easily remove press the button to melt the ice clogging the pipe. This is a cheap design which did not go through design validation and qualification.

RE: 5.2 CU Ft Top Load Washer, Model # MVWB865GW0, Serial # C84370937 - Purchased Jan 2019. The clothes come out terribly tangled and severely wrinkled, even when using the Wrinkle Control or Delicate cycle and occurs in every load size. Ive tried every cycle, including the deep fill and low spin speed but items are so wrinkled that whether I lay flat or hang or put them in the dryer, I have to iron them, which I never did before.

I have been trying to get my refrigerator repaired for over 5 months through the extended service plan I paid for. They sent out a service repairman. He could not repair the refrigerator without some parts so he ordered parts. We waited months to find out he can not get the part anymore that he ordered. So now Maytag Extended Plans and Service Power said they would have to replace the whole refrigerator but every time I call about it, they give me the runaround and say someone will be calling me back within 48 hours.I never get a call back. I give them a few days, then I call back and get the same runaround again. Im getting nowhere with these people. My refrigerator is a $6,500 refrigerator that Im sure they just dont want to replace or offer me anything for that matter. They should abide by the contract I have with them.

Eight years ago we bought all new top-of-the-line, stainless steel refrigerator, double oven range, dishwasher and microwave. All began malfunctioning within the first year: *The refrigerator began to make a loud rattle and the digital control pad needed to be replaced -twice within the first year. Within the next year the compressor had to be replace. *Dishwasher electronic control board was replaced twice, broke again and is still broken. *Microwave door handle broke off, and turntable motor broke.*Range burner ignition system only works on two burners and the shelf for the top oven does not fit -*Maytag refused to replace. Also, after using self-cleaning feature the lower oven still fills the room with smoke so it has been used very little. So, how much worse could it be? I had faith in Maytag-thats why we bought the brand.

I did not purchase it. This range came with my home. The electric range works great. It is thorough and I dont have to worry about the gas being on and filling the house up. Electric may not be for everyone, but it is the way to go for me. I will look for similar if not the exact same make/model if a replacement is necessary. I dont mind spending a little extra to ensure the product will last. So many products dont last nowadays and it is sad. I am not an avid cooker, actually I tend to mess up a lot of food recipes but the electric range helps me to reduce the number of problems I run across with the durability and accountability of the product. It cooks throughout the entire dish/pan and I have never had a problem with the unit working properly, just the user not working properly. Haha.

I have a top load commercial tech washer with an agitator that is brand new as of September 2019. I have done all of the troubleshooting suggestions and nothing works. I use 1 tsp of liquid cold water detergent, deep fill, extra rinse, and clear liquid oxi and my darks still come out with white stains. I have had a Maytag tech check out the machine and it checks out without issues. I would never recommend this product to anyone!

I have Maytag Model MGT8885XS03 Gas Range. I bought it in Nov 2013. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within first 13 month. Then another valve got stuck about a year ago and the third one got stuck today Nov 19. So far I spent $400.00, just for 2 of them and the last one has not being replaced yet. This is a safety issue, because it always happen when the stove is on and will not turn off. I need Maytag to replace my stove because I am afraid this will burn my house down. I bought Maytag because they always advertise as quality product, and now I have to live with the nightmare of burning my house down.

We purchased the Maytag Bravos MCT in July 2017. Just passed the 1 year warranty and the glass door just shattered. No reason for it really other than it must have been defective. Nothing dropped on it and it wasnt cold or hot in the room. I got nothing. Maytag said they didnt know why it would happen, and would have to send service tech out. A lid for this type of washer alone is $200-$300. Buyer beware. Dont get a glass top loader.

Maytag Centennial Commercial washer - We purchased this washer approx 4 years ago and have never been satisfied with the job it does. Most loads require a second rinse cycle and then perhaps not a good job on the clothes. We have had it repaired twice as it makes a god awful noise and does not do a wash cycle. I believe the repairman has replaced plastic pulleys both times and now it needs the repair job done again. High efficiency has led to high disappointment. We will be looking at getting an older style agitator model as we know they work! Maytag will have to pay us to buy anymore of their products, not impressed at all.

Maytag Bravos XL he Washing Machine - Having owned several Maytag washers in the past, I thought this would be perfect, instead, it is the worst washing machine I have ever had. This machine does not clean well at all, spots on clothes stay put. I have tried different amounts of HE detergent and clothes are twisted and wrinkled terribly and have remaining soap residue on them, even when I use less soap than recommended. I wish I would have returned this machine immediately after a few loads. It doesnt get better with time. It is very loud, but that is the least of its problems.

My husband and I purchased a Maytag Bravos washer and matching dryer in November of 2009. At three or four months old, the dryer quit drying and was emitting a weird smell and smoky air coming out of it. It was under warranty so a technician was called. A fan blade inside it had broken. The repairman replaced it and the motor as a precaution. There was absolutely nothing inside it that could have broken the fan blade and I always check pockets. My hoses were clear also. He told me that it looked poorly designed inside for air flow. He made a box out of sheet metal to fit inside it that he said would help it with air flow on the inside. I still have the dryer but I dont like it very much because it still doesnt do a great job of drying. It has to run too long and at too high a heat to dry laundry. The latch on the door broke a few months ago and had to be replaced too. I havent had problems with the washer as of yet. I like the washer and it washes very well but I will not buy a Maytag washer or dryer again. WHIRLPOOL OWNS MAYTAG NOW AND THEIR PRODUCTS ARE ACTUALLY MADE BY WHIRLPOOL SO I WOULDNT TURN TO THEM.

First off I dont usually spend my time writing complaints; however, I feel Maytag is deserving of my complaint. Purchased dishwasher Model #mdbh979sab1 in 2013 and days before the 1-year warranty was up the front control panel quit responding, rendering the appliance useless. Got that fixed under warranty. Now about 1 year later guess what... Its got the same problem. Began to read others post on this site and found that this is a common issue. One person posted that her dishwasher began to smoke and nearly caught her home on fire. Maytag was kind enough to offer a paid service call and enrollment into their extended warranty program. I think Ill cut the umbilical cord on this one and go get something more reliable and doesnt pose a potential fire hazard.

Bravos WL purchased in May 2015. Terrible product. Last week stained 2 shirts beyond repair. Maytag service repairmen stated these machines were poor quality and the only settings that somewhat work are Deep Wash and Bedding. They recommended I buy something other than Maytag. I am not making this up - it was unbelievable. I got Maytag on the phone while the service techs were here so they could hear the comments. The supervisor, Kimberly, said I could not get resolution unless the technician declared it a functional failure. I asked for the definition, as I would assume the basic function of a washing machine is to clean clothes. Still working the steps to resolution, but I believe there is evidence for a class action lawsuit.

Every 3 months, the freezer compartment needs to be dismantled to unclog the defrost drain hole. When this occurs, it dumps all the defrost all over the base of the freezer which then leaks water out of the freezer door all over the floor. Clearly a design flaw and Maytag will not acknowledge this but appliance repairman says these are notorious for this. A $1700 fridge shouldnt do this. Never will I buy a Maytag again, a complete POS.

Maytag dishwasher MDB7749SBM2 - I purchased this unit from Home Depot. It worked fine when working. In less than two years the control panel had issues. Would not let you start cycle, would randomly start on its own, would light up randomly, would only let one cycle work, would not work at all, etc. I received no help from Maytag. After open up the door panel the problem is obvious. The ribbon cable from touch (control) panel to control board had black spots from corrosion. Poorly insulated or poor design. $150 for part and another $100+ for repairman. As Ive seen from several of these posts it appears to be a common problem now to Maytag, which they choose to ignore in spite of class action lawsuits. Obviously last Maytag product Ill ever buy.

We have a Maytag drying center that is almost 6 years old. It never did a good job drying especially for the money we paid, but it just quit on us two weeks ago. We purchased it from TA Appliances in Barrie, Ontario who recommended that we call B&K Appliance repair to fix it. The owner showed up and said he would be back to us in a few days to fix it, as soon as part arrives. He now wont return calls and it has been two weeks, so we called Maytag customer service. We knew we were in trouble when we received a message telling us Due to higher than normal call volume... (so much for the Maytags that never need repair). Anyway, we finally reached an incompetent, ignorant and anti-customer service representative who proceeded to tell us in an extremely, nasally drawl that the part needed to fix our 6 years old dryer is no longer available and the most they could offer as compensation for this on our $1500 plus tax dryer that should last at least 10 years is $120. This is for a dryer we never used more than 5 times a week.

Holds a lot of laundry. Spins laundry almost dry so its quicker in the dryer. Easy to load. Easy to add wash soap and fabric softener. Only problem is its very deep to reach the laundry at once its done if youre not real tall.

This Maytag Bravos is the worst washing machine I have ever had. Who ever heard of washing with almost no water? Takes way too long. Clothes not clean. Any water savings way offset by ridiculous length of washing time. I can wash and dry a load of clothes in an old stacking washer/dryer before one finishes washing in this thing. I was excited to get it and now cant wait for it to go. Wont make this mistake again.

I purchased Maytag dishwasher (model # MDBH979AWW3) in June of 2010. Trouble started on washer after 18 months. Touch pad buttons dont all seem to be working. Occasionally gets to run after slamming door multiple times, but dispenser doesnt function properly. After trying to diagnose myself with door switches, connectors, etc., I caved in and called service. Service quoted $470 parts and labor to fix the problems, including control touch panel, dispenser, and control board (seems common from what I read here). Wish I had seen this string of posts before I called Maytag/Whirlpool customer service to see if they would help before I did any repairs. The responses I got from the service rep were rigid and scripted. Only time she varied from the script was to explain that modern high-efficiency appliances dont tend to last as long as ones 20 years ago. 18 months? Really? I might buy that if it was a mechanical durability design issue. Supervisors responses were also scripted, pointing back to the 12-month warranty. She said she did a warranty search on my model and that there was no warranty concern for this problem (really?). If there was, she might be able to help me. I guess there is no warranty history because most failures are between 12-24 months and the consumer has to pay for replacement outside of warranty. No semblance of customer service or customer care, just repeating what is on their website. Response was: I am sorry you are dissatisfied with the product and my response, but there is nothing I am authorized do. Sent an email to Maytag customer service regarding the problem and customer service interaction. They called back saying they stand by the original customer reps response, but offered to have someone else come out to give a second opinion on the problem. From what I read here, that doesnt seem necessary. Wish Maytag/Whirlpool would at least acknowledge that there is a problem, even the auto industry seems to have figured out a way to equip the service industry with known recurring problem history (TSB) and offer token help to keep customer loyalty. Apparently another quality organization fallen victim to short-sighted methods of maintaining shareholder value.

On May 11, 2010, I purchased a Maytag washing machine from Lowes. On June 22, 2011, the machine wouldnt empty out on the rinse cycle. Lowes was called as the machine was only one month out of warranty. They dispatched Appliance Plus for a service call which would be $80.00 just to diagnose the problem. It turns out the machine needs three parts - a timer, an ATC switch, and a rinse switch. All totaled, this will add up to over $300.00, plus the $80.00 for the service call.Appliance Plus tried to contact Whirlpool to see if Whirlpool would at least pay for parts, being it was only one month out of warranty. The answer took 5 days and the request was denied. I was told I should contact Lowes Service Advantage and maybe they could contact Whirlpool for a special consideration, again, being it was only one month out of warranty. I made the call and they said to give them two business days turn-around for an answer. On June 30th, Lowes said Whirlpool was looking for the serial number and I provided it. They told me to give them another 2 business days turn-around. On July 3rd, I again called Lowes and they informed me that they still hadnt heard from Whirlpool. Finally, on July 7th, I received a call from Lowes saying Whirlpool denied the request.

Maytag Bravos XL - I have always loved Maytag and never had any problems. In Feb we did some major remodeling with new flooring in our laundry room. Decided to buy a brand new washer and dryer even though our 10-year old Maytag washer and dryer worked perfectly fine. After looking at Home Depot and Lowes we first settled for a Samsung W & D but before it was delivered we shopped some more. After doing some inquiring we decided that we wanted to stick to a long trusted W & D line so we chose this washing mashing and matching dryer. From day one I decided I did not care for it. I found if I put too many clothes in that they did not come out clean. Any dark pants would come out with what looked to be soap or softener stains and would have to rewash 1 or 2 times. Now I can only put in about 4 pairs of pants to wash. I have been cleaning it once a month as the manual says to do but yesterday I noticed a terrible odor coming for the washer. I could smell it out in the hall. I did the cleaning again but still smell it. Now after searching the internet I find a video that shows the problem is mold under the drum. No amount of Affresh or bleach is going to clean something UNDER the drum. It is not my job to have to take this apart every few months and clean out mold and moldy water. Sounds like this problem has been going on for a few years and this should have been fixed long before this. I wish I had my old faithful washer and dryer back. Maybe I should have stuck to the Samsung washer and dryer.

I bought a Neptune Washer in 1999. 6 years later (2005), it started making the 747 landing noise. It was implied that somehow it was our fault, maybe, something from my contractor husbands pocket. After all, it was a Maytag, and surely there could be no design or engineering flaw! (My daughter still has 34-yr.old one.) We were told the repairs would be so expensive. It would be wiser to buy a new one. Foolish me, I bought another Neptune to match my dryer. Of course, now this one has the same bearing problem and again its cheaper to buy a new washer. I am angry and not sure how to proceed. Any washer, but especially a Maytag, should last more than 5 - 6 years. I should not have to buy my 3rd washer in 12 years. And if I do, it certainly wont be a Maytag!

I bought this washer (Maytag HE) almost a year ago, and if I could redo my choice, I would not choose this machine. There is no separate spin cycle. Often items are left with quite a bit of water in at the end of the wash cycle (often literally dripping as you transfer to the dryer), and you cant just rearrange them in the washer and then spin again. The only option on the washer is to both rinse and spin, which almost never helps get out more water. So you then have a heavy load in the dryer, much longer dryer time, and higher utility bills to get some loads dry, especially bath towels, sheets, jeans, etc. The washer is large capacity, but if you fill it more than 1/2 to 2/3 full (depending on the heaviness of your items) the spin cycle definitely will not get nearly enough water out of the clothes. The lid on the washer is SLOPED!The most ridiculous design I have ever seen for a washer, everything you set on top, even for a moment - laundry detergent, folded clothes, wet clothes - ends up on the floor. And the lack of agitator means at the end of the cycle, some loads that contain a sheet or any large flat item (tablecloth, etc.) the rest of the items are captured below the larger flat item that is over them like a mushroom cap. You cant tell how long the items have been like that in the washer, but its hard to imagine they are getting properly cleaned and rinsed. You absolutely cannot use powder stain removers, especially OxiClean, unless you are using the oxi cycle (much longer than regular cycle) because with any other cycle you will have white cloudy patches on all your clothes and items where the powder dissolved in the water but did not rinse out. You have to manually scrub them out, as putting these items through another wash cycle does not remove all the spots.

The Maytag washer is very quiet & economical by filling the amount of water needed per load so actually a money saver. Also got the huge drum to wash quilts & blankets. My old one lasted 10++ years. Hopefully get as many years out of the new one.

I purchased my dishwasher exactly two years ago. We are empty nesters so it has had light use. Today, when I tried to start it, the control panel would not work. Thanks to what I found in your site. I will not take a day off of work to wait for a repairman only to have it fail a second time. It is hard for me to believe a company that builds its reputation on a bored repairman would produce a product with a faulty control panel and not do something about it. Like your other folks, I will never buy another Maytag product and will not the waste the money to repair it. I am going out tomorrow to buy another dishwasher and throw this one away.

I love my Maytag washing machine. It have different settings for the wash, also a size load for your washing, and I love the rain cycle. You could do single runs with Downy or extra runs which is great. Especially great if you’re doing blankets and towels you need that extra rains. Great reliable machine. Highly recommended.

I bought a Maytag washing machine, model number MHW6630HW2 in January 2021. It works fine on ordinary loads, but it cannot spin the water out of bulky items, not on any setting. I put my machine-washable winter coat in the washer and it left it full of water. I re-tried on 4 different settings, and though the washer spins, it cant spin out the water. I went to the Maytag support site. The sites said my model doesnt exist. The phone number for support does not allow you to get any support other than a service call. The Chat option doesnt give a lot of support either. They said that if I call for a service appointment and the service technician finds that the machine does do a spin cycle, then the appointment is not covered under warranty.

I purchased a Maytag Bravos XL Commercial Technology top loading washer, model # MVWB850YWO, in May 2012 and it was delivered in August 2012 due to a home purchase not being consummated. Anyway, I bought this washer and the matching dryer at Lowes and purchased a 4 year extended warranty with Lowes. This would cover me with a warranty through August 2017. I had some problems with the washer while under warranty and had it repaired at least twice. I have had, and still do, have a water leakage in the washer. The water when dispensing into the detergent compartment splashes over and you would think it would just go into the tub. Someway the water leaks down the inside of the washer and runs out onto the floor also causing rust to the inside of the front panel. The resolution was to turn the water pressure down on the supply lines. When this was done, the washer would quit running due to not enough water being dispersed into the drum. A replacement seal was installed and I still have the same problem. The repairmans final resolution was to put tape over half of the detergent dispenser to hold the water in the detergent dispenser and still allow me to put detergent in the dispenser. So, a towel is in front of the washer to soak up any leakage. Now, just 5 months after the extended warranty expired, the bearings under the wash tub are starting to roar during the spin cycle. I contacted Lowes service again and basically I am out of luck. The repair cost is expensive, the part and requires 2-3 hours of labor. I decided to chuck this washer and buy a new one. My wife found one that has an agitator, unfortunately another Maytag, and wants it as she has said the Bravos washer never seemed to get the clothes clean (due to not having an agitator). When checking online for references on a new washer and any recalls on my current washer, I discovered other Bravos XL owners having the same problem with the bearings in the tub. I contacted a local business to try and sell it to him for cheap and when I told him what was wrong with my washer his reply was, I have one just like it out back with the same problem. Dont need two problems. Cant even get rid of a Maytag washer due to it being junk. Many other reviews have listed problems with Maytag products especially since Whirlpool bought them. The Maytags of today are not your parents Maytag. Used to be the Maytag repairman sat around his office waiting for repair calls. This has changed considerably since Maytag sold out to Whirlpool. After doing some research, it seems Whirlpool has bought just about every company selling washers and dryers and are making them as a disposable item. I would advise not purchasing any product that is under the Whirlpool corporate umbrella as I feel whatever they buy, even a superior product like Maytag, they cheapen the product and try to benefit from the name, as in the case with Maytag. So, no more Maytag or Whirlpool products for me until they have proven they can build a quality product once again. Hello GE!!!!

I purchase my Maytag Bravos washer from Sears in May 2011. In February of 2014, I started to get the UL message, meaning unbalanced load. I would re distribute the clothes and sometimes that did the trick and others not so much. Now every load comes up UL. I tried putting the machine on the drain and spin cycle to at least get the clothes a little bit drier but the UL message still appears and the clothes are still soaking wet. I lifted the washer up and there is an oil/grease type spin pattern under the washing machine. I called Maytag today (which is now Whirlpool I guess) as the washer has a 10 year warranty on the drum and motor. I was told a service call is $129. When I mentioned that I had Googled the product and saw many reviews with the same exact problem, she stated the Bravos has no common complaints. From what Ive read, it seems to me it would be more cost effective to go out and buy a new washing machine and it obviously wont be another Maytag or Whirlpool.

I like my fridge. Its a old one and still works. Its been very reliable and have never had a problem with. I dont think I would ever purchase a different brand for Maytag is the brand for me. They last for years.

The $1,100 Maytag Bravo XL does not have a dedicated spin cycle. Its rinse and spin. When out of balance, you rearrange and it rinses AGAIN - 15 minutes - before you know whether its balanced. By rinsing again, it can redistribute to be out of balance. Repairmen (w/ extra warranty) said you cant wash bath mats, bedspreads or pillows though it had giant capacity! They would charge me if I called again about it (3 strikes). So bought a used Kenmore with no computer panel... Its great! My dealer had the Maytag hauled to a dump, he would not sell it to anybody as he had integrity.

Lets be real and say that people with good experiences dont often end up on websites writing reviews because they are busy enjoying their product! I purchased my set in early 2012 and will admit that initially there was a learning curve with using a washer with no agitator. I enjoy doing laundry and Im really good at it but with this washer I had to change my routine. Always pretreat stains. Deposit clothes loosely around the drum and shake clothes loose before putting them in the dryer. My clothes come out great! I have a child, two dogs and a greasy truck driver man and everyones clothes smell great. I can wash my king bedspread and anything else in my house with no issues. And my washer has never torn any of my clothing, however fragile. I dont iron often and I hand wash nothing.I give 4 stars instead of five for the extra steps to ensure my clothes are clean and wrinkle free. No they dont make things like they used to but thats with all the new stuff. My moms 3000 dollar Samsung set (her washer) isnt working as I write this. Too bad more people with good experiences dont get online and share. Hope this has been helpful.

Do not buy this dishwasher unless you get the extended warranty. We purchased this dishwasher in Jan 2014. The first one delivered was completely busted up (which was probably the delivery companys fault for not handling it correctly). Then we had to wait for the replacement one to come in to get installed. In Sept 2014 the control panel stopped working. It was repaired under the warranty but it took several weeks for the authorized repair shop to be able to come out, diagnose, order part, and then come back to fix it. Now March 2015 (5 months later) we had the same exact problem with the control panel. The repair company was unwilling to order the part to bring with them even though they already had it in their records what we needed due to the previous repair. It was going to $300 to repair it since they only warranty the repair for 90 days. We decided to replace our 14-month old dishwasher rather than put any more money into it. Shame on you Maytag for putting out such a bad product - obviously this is a common problem. It is quiet and does a good job of washing but to have it take several weeks to get a repair done combined with having a problem that cost 50% of the purchase price to replace twice within a year of each other, absolutely not worth the money. Should have just spent the extra on a higher quality product. Will definitely get the extended warranty on whatever we replace it with.

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

I have had nothing but headaches with our washer. We purchased it 4 years ago and after using it for a few months, I took it out because our clothes came out smelly and unclean. Called Maytag and they did nothing. So we went back to a regular washing machine and put this machine in the corner of the basement. I refused to throw away a $1,100.00 machine! So this year our machine quit, so we decided to try using the machine again to save us some money instead of buying another one... Well, that lasted for only a short time. Clothes still smell, came out unclean and just yesterday, the machine stopped rinsing and spinning! This machine has barely been used and its been nothing but trouble. Maytag service just plain sucks. They dont care about their consumers. I will never buy a Maytag again and I always let everyone I know to not buy this type of machine.