I bought a new stainless steel Maytag refrigerator last year. It had a one-year warranty. Wouldnt you know, 14 months after my purchase, the icemaker stopped working. Did not take out the extended warranty, as I thought I had purchased a quality appliance. I contacted the store where I purchased it. Was told it would cost $150 to replace. I have a feeling this appliance wont last very long. Suffice it to say, I will never purchase another Maytag appliance.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

Maytag Washer 2016 HE top loader. This washer is horrible to use. I hate everything about it. After your clothes are put into the drum and you close lid to start here is what happens EVEN though I select deep water: it puts small amount of water in and then it agitates the whole big load. This is so stupid! Can you imagine a large load of your clothes agitating with a very small amount of water in the drum?So to get around that problem, you have to push pause button and shut the lid after your soap, softener and then listen until that first amount of water fills and agitates, then you have to push pause and quickly put in your clothes. Then you shut the lid and again push the start button so it will fill with more water. Then if youre lucky in at least an hour your load is finally finished. I hate this washer. My boyfriend bought it and I asked him several times to PLEASE return it. He didnt so now were stuck with it for God knows how long. The one good thing about this is I will know to never buy one of these for my house.

I own my oven for 10 years. It still looks brand new. The bottom oven went out and they do not sell the replacement parts anymore. I think its terrible that I had to go and buy a new oven when mine still looks brand new.

Low water level resulting in poor cleaning. Very poor design. Requires 2 rinses so the water savings of the wash cycle is a joke! Im very disappointed with the so-called Maytag quality. If doing very very small or handwash loads it work somewhat ok! Would never buy Maytag again!!

July 2011, I bought a top loader Maytag washer from Best Buy. In October, after I had the washer just a little over 3 months, it quit working. Dead. I called Best Buy that said they only stand behind a product for 3 months and since mine was about 3 months and 2 weeks old, I had to contact Maytag to fix it. When I contacted Maytag, it took them 3 long, angry, upsetting phone calls before they finally made an appointment for someone to come look at it the next week. I was without a washer for 9 days and when the man came, he said it was too new for parts. He would order a new latch (apparently, he thought it was not latched and so would not run), but it would take a while to get it in. Hed call me. 3 weeks later it and he showed up. He said apparently, the latches were bad because the new one didnt work either. He would order one more and if it didnt work, he would have to order a new back panel and it could take a few months, instead of weeks, for it to come in. The second new latch finally came in and the washer still did not work! However, he reprogrammed its computer to accept the new part and it finally worked. By now, it was the end of January 2012! My new washer I had paid for in 3 payments had been broken down longer than it had run! Best Buy said basically, you buy it, its your problem. Maytag said basically the same thing. They were hateful and it took over 10 phone calls to get anything done! I was not reimbursed for any laundromat usage, gas or phone minutes, of course! I was treated like I was expecting something that I had no right to have, a working product. Once I bought the product, it was my problem and not theirs. The end. I will never buy another Maytag product!

I have a Maytag Centennial washing machine which is about 3 years old. In the past 6 months I have to replace the actuator twice. I have had Maytag washers for about 40 years. I will never purchase another one unless it is the old style. That would mean that it would be a used one. This machine is a bad purchase. Maytag use to stand for quality, but not anymore.

First bought a nice looking Samsung. Didn’t last 6 months. Upgraded to a nice Maytag with steam and have never regretted it. It’s been years of worry free and trouble free use. My Samsung dryer is on the way out the door and to be replaced with a Maytag too.

A lot of repairs in 6 years from belts. It leaks water around seal on door. Only part of the cycles work. I would not recommend the Maytag washer to anyone. When I got it I expected or hoped it would last 10 years or more.

Has anyone talked to an attorney to see if a class action can be filed? My fridge is leaking, sheets of ice on floor of freezer, and ice maker doesn’t work. Looks like it’s the norm for these. Please post if you have spoken with an attorney. If no one has, I am going to.

The Maytag range was purchased locally in 2012. The racks kept falling as the oven cavity warped in a convex making the rack supports too wide. The racks fell at the best position to cook a turkey. This could be dangerous when lifting something like a turkey or pie with filling! I was told that the oven cavity is NOT replaceable and I needed to purchase a new range! $1,600.00 plus taxes were spent just three years ago and now Im being told it cannot be repaired, no parts are available and needs to be replaced! Im sorry but I feel cheated and hurt because Maytag will not give any concession despite my pleading. What a dirty way to conduct business! No concession except an offer to cancel the service charges so far if I replaced it with another Maytag range from Delhi Radio Ltd. Are you serious?Why cant wider racks be provided for in these cases? Just what kind of engineer would compromise the thickness of a ranges oven cavity? Then build the range in such manner that the defective part is not available and cannot be replaced? Its a sad day for Maytag! Shame on you! Ive seen Maytag washers built in Newton last 35 years of hard family type washes! Whirlpool has purchased the name, stamped their own products with the Maytag name, and rested on the fine reputation of the name brand. Everything else is different! The Newton plant is in mothballs leaving hundreds of proud faithful employees stranded. Its a sad day for me and many others who were duped by a brand name and got something completely different.

Consumers be aware! Anyone who’s considering purchasing a Maytag Appliance I would highly suggest reconsidering! I bought a $2000+ Maytag fridge Model # MFT2776FEZ00 in March of 2017 and have had numerous repair calls on it: Several for ice maker not make ice, ice freezing in the bucket into 1 big CHUNK, water running down front of door on the inside and outside, to not working at all and ice maker needing to be replaced. Several calls for fridge not properly cooling (temperature was set at 37 degrees F but the temperature in the fridge is 55 degrees F - per 2 thermometers), food is spoiling. The back inside of “Temp Controlled Pantry” is freezing everything and whole back wall behind the drawer is frozen with 1-2” of frost and ice. Defroster is not working and again parts being ordered to repair an obvious issue with this model.I contacted Maytag and their response was “sorry, we can document the problem.” They will do nothing more! These Appliance companies are ripping off the consumers! Everyone passes the buck! Repairman says, contact the Appliance store you purchased it from, Appliance store says, contact Maytag, Maytag says it’s the repair companys issue.

I purchased the Maytag MDB7749SBM dishwasher just over 2 years ago. After owning for 1.5 years, the control board malfunctioned. After discussions with Maytag customer service that began in late December 2014, it was finally repaired in February 2015, with the control board being completely replaced. Within just a few months the dishwasher again fails. The first time, it would not stop running. This time, it will not run at all. I called customer service today (August 1, 2015) and they expect me to pay for the repair.It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue, as the customer service rep indicated today (she said her information showed no recalls). Within two years I am now faced with paying $600+ for a dishwasher for a second time. This is terrible customer service on Maytags part. They have lost my business and I am warning consumers on every platform I have.

I have been on the chatline with Maytag customer service for two days, trying to enforce my warranty, which expires next week. My washer flooded my kitchen over the weekend, and I contacted Maytag to schedule the repair under the warranty. First, the woman, Aisha, looked up my registration, and confirmed that I was who I said I was, that my address and phone number had not changed, and told me that according to the records, the washer was purchased on 2/7/2011. Whats the problem? First, they wanted the model and serial numbers. I realized that this is important information in determining what machine needs what repairs, except there was not one sticker anywhere on my washer! Aisha said that the technician would not perform the repair, if the manufacturer did not install the model information properly on the machine. As if I had any control over the placement, or lack thereof, of proper ID for the washer. This was followed by a request for proof of purchase. I explained that I moved, and misplaced it, but I would have it emailed to me from the original purchaser. I was told that unless she could verify the proof of purchase, and the date of purchase, she could not schedule the repair under the warranty. This is despite the fact that not 5 minutes ago, she had just read this information from her computer! I asked her why would I register someone elses washer under my name and address? She didnt care. I told her I would have the receipt emailed the next day, and she stated that regardless of the date I requested, and scheduled the repair, if the actual repair took place after the expiration date of the warranty, it still would not be covered! I told her that makes no sense. I have no control over your scheduling issues. If you cant honor the warranty if the repair is made after the expiration date, then I need a date prior to that. I am entitled to the terms of the warranty, and intend to use them. Aisha said again that, without proper proof of purchase and purchase date, without proper tags on the washer, and if the repair takes after the expiration date, it would not be covered. I disconnected from her, and reconnected with another rep, who told me that some of the information Aisha gave was incorrect. I can schedule the repair, get the receipt and email it, or submit it through the chat, and regardless of when the repair was actually done, the warranty would still be honored. This person couldnt be sure what effect the lack of proper tags would have on that. My third re-entry into the chat was no better. I located a copy of the receipt in my email, and contacted the chat again. An almost amazing thing happened! This woman again confirmed all of the information Aisha recited last night, and was prepared to schedule the repair, without even asking about proof of purchase. This woman, Jennifer, was willing to schedule the repair, verify that it would be covered under the warranty, even if it was after the expiration date, because I had called and arranged the appointment before the expiration date, and she was willing to have the missing manufacture tags replaced. I had to ask her three times to review the email, and confirm that I had the correct receipt for the technician. I asked if the technician in the course of repairing the washer, had to remove the drainage hose, could he either replace it with a longer one, or add an extension, because according to Lowes at the time of installation, the hose they installed was supplied by the manufacturer, not them. Jennifer stated that since he was only there to repair the leak, and installation is not covered under the warranty, I would have to pay for him to replace the wrong hose, with the correct hose myself, even if he removes it! I told her that she needed to ensure that the technician absolutely did not remove the drainage hose from the back of the washer during his repair, because if he removes a part that is obviously the wrong part, and then replaces the wrong part after his repair, I would file a complaint every single place I possibly could. Why would a repair technician remove a part, determine that it is the wrong part, and then put it back! That is like a mechanic repairing the axle of a car, and discovering the brakes are bad, but since he is only there to repair the axle, he replaces the bad brakes after fixing the axle! He was going to be able to replace the missing manufacturer tags, though! This entire process took at least 3 hours and two days. To date, Maytag/Whirlpool is absolutely the worst company I have had to deal with, right after Sears, and ahead of AT&T. The consequences are that so far, Maytag refuses to have the technician replace the wrong hose with the correct hose, if he removes it in the course of repairing my washer.

I bought a refrigerator from Home Depot in July 2013. In late November 2014, I noticed water on the floor in front of the fridge. I called the Maytag customer service and reported the problem.. The customer service rep explained to me that Maytag discovered a design flaw in the part that allows the water to drain when going through the defrost cycle. I also called Home Depot. Their response was it was my problem because the fridge was out of warranty and I did not buy an extended warranty plan. After two more calls to Maytag, they scheduled a service appointment. The service repairman told me the same thing about the design flaw. I have the old part and the package the new part was in. The two parts are completely different. I requested that Maytag or Home Depot replace the fridge or give me credit for the amount I spent. Maytag is now saying there was not a design flaw and because of that, Home Depot refuses to replace the appliance. I will never buy another Maytag product or shop at Home Depot. The extended warranty is a way to place the responsibility directly on the consumer and eliminating the responsibility of the manufacturer and the store.

It does not matter what mode you select, every single piece of clothing comes out a scrunched up wrinkled mess. I have to wash all clothing in bulky sheets mode because it is the only mode where the clothing actually gets submerged in the water. This washing machine is extremely loud and it is without a doubt, the worst purchase I have ever made. I have never written a review before, but this product is so horrible and frustrating. If I can persuade one person not to purchase one, I feel that I have done a good deed.

Because it is the high efficiency model, need to leave the lid open so interior will dry and not smell musty. Also, recommend using a washer cleaner such as Affresh or Tide tablet every now and then. But works great!

350.00 dollars for repair on a 3 1/2 year old washing machine. Machine wont finish spinning and lid lock keeps flashing on and off and sometimes stays off. Never finishes spinning. A lot of complaints on this! This should be recalled! Always was a Maytag customer but no more!

I contacted Maytag, and they claimed to know of NO issues with this fridge. I told them its all over the internet, many others with the same fridge and same problem. Anybody up for a class action?

I bought the Maytag Bravos XL HE washing machine because I needed a machine that could handle large loads to save me time doing multiple loads for everyday items like jeans to towels, blankets as well as delicates. This machine is a COMPLETE disappointment. It does NOT get anything clean unless I wash it 4 times with bleach and pre-stain 4 times. You know what bleach does to your clothes! The water level is so low I can only wash 4 things at a time and I still have to wash additional times. It doesnt get the smell or food stains out. Not a good choice for an active family or person. Ive had clothes come out with suds still on them after washing three times. I use less than the recommended amount of HE detergent. There was a $250 agitator washer by GE at Lowes but it was smaller - how I wish I bought it. These impeller HE machines dont work. My advice steer clear of this Maytag product unless you like to waste your time re-doing loads of laundry.

There was a maytag dishwasher in the house we bought 11 yrs ago. The only problem we have had is a recall on the rinse aid dispenser which was replaced by a service man but never worked again. We are completely satisfied with the operation of the unit, our only disappointment is the wire racks. The original racks plastic coating broke at the end nubs and became rusty and swollen. We found someone selling a unit and we just took the racks and left the unit for him to resell rackless. Unfortunately not two yrs later the same thing has happened to those racks. Even tried these little plastic covers that are made specifically for this problem. They were virtually impossible to get on and didn’t last more than a few months.

Bought a Maytag refrigerator/freezer 18 months ago. The freezer went bad. The first repair guy said it needed a new computer board which wasnt covered. Called Maytag, they wanted another repair service to look at it. He said it needed a new evaporator. We have now spent $250 to be told the repair will cost another $500. Maytag will make a goodwill gesture because we are a nonprofit business to cover the part only so we will still be out another $300. This is unacceptable for a relatively new Maytag. Obviously they can no longer be counted on to back their equipment. Very disappointing.

This washer stops every 10 minutes, sometimes taking 3 to 4 hours to complete one spin cycle if it is completed at all. All troubles began shortly after warranty expired. NEVER EVER will I ever buy Maytag again. I make certain that I tell everyone I come in contact with about the pathetic quality of Maytag.

I purchased Maytag dishwasher (model # MDBH979AWW3) in June of 2010. Trouble started on washer after 18 months. Touch pad buttons dont all seem to be working. Occasionally gets to run after slamming door multiple times, but dispenser doesnt function properly. After trying to diagnose myself with door switches, connectors, etc., I caved in and called service. Service quoted $470 parts and labor to fix the problems, including control touch panel, dispenser, and control board (seems common from what I read here). Wish I had seen this string of posts before I called Maytag/Whirlpool customer service to see if they would help before I did any repairs. The responses I got from the service rep were rigid and scripted. Only time she varied from the script was to explain that modern high-efficiency appliances dont tend to last as long as ones 20 years ago. 18 months? Really? I might buy that if it was a mechanical durability design issue. Supervisors responses were also scripted, pointing back to the 12-month warranty. She said she did a warranty search on my model and that there was no warranty concern for this problem (really?). If there was, she might be able to help me. I guess there is no warranty history because most failures are between 12-24 months and the consumer has to pay for replacement outside of warranty. No semblance of customer service or customer care, just repeating what is on their website. Response was: I am sorry you are dissatisfied with the product and my response, but there is nothing I am authorized do. Sent an email to Maytag customer service regarding the problem and customer service interaction. They called back saying they stand by the original customer reps response, but offered to have someone else come out to give a second opinion on the problem. From what I read here, that doesnt seem necessary. Wish Maytag/Whirlpool would at least acknowledge that there is a problem, even the auto industry seems to have figured out a way to equip the service industry with known recurring problem history (TSB) and offer token help to keep customer loyalty. Apparently another quality organization fallen victim to short-sighted methods of maintaining shareholder value.

I am extremely disappointed with Maytag and the representatives I spoke with this evening. One laughed after I told her I was 7 months pregnant and without a fridge for a week after owning it less than a year. I was repeatedly and curtly told, We dont cover that, when I asked only to replace the recent food I had purchased. After having to request a manager several times, I was put on the phone with Dana ID ** who said she would not be able to help with any food despite the delay of a week for repairs to our fridge. However, she could extend our warranty for 6 months.The only reason we were able to get someone out as early as we did was because we knew a licensed Maytag service repair company. Otherwise, we would still be waiting for someone to come out to tell us it would be another week before repairs. The originally assigned service repair company by Maytag did not return our call. There was no concern or empathy from the Maytag representatives that I was pregnant and could have eaten food that was not cooled to prevent bacteria growth that would harm me and my baby.Even their service repair technician recommended to contact them about the spoiled food since it was impossible for the repairs to be completed before the end of the week. We will never purchase Maytag again. The appliance failed with no warning in less than a year, and the representatives made no effort to resolve our issue of being without food for a week.

Bought a Maytag refrigerator from Home Depot about 2 years ago. Like everyone else we are having leaking problems from the freezer drawers. I wonder if anyone has had it repaired and whether it was repaired

Called Maytag to set up service call at around 9am for my washer, was given a rate of $129.00. Thought it was High but it was my only off day and felt confident that it would be a reputable company. If Maytag Priority Service would refer A&E Factory Service to me for service they must be a reputable company. I was sadly disappointed after numerous calls to A&E Factory service, a 5 hour window was not met and they were not concerned other than they would document it. Then I find out that A&E Factory Service has a Rating of 1 1/2 Star rating out of 5 and thousands of complaints to BBB and Consumer Affairs, dropped by Lowes for horrible customer service but Maytag Priority Service recommends them to service their product, says Volume on how Maytag takes care of their Valued customer after the sale. Maytag has lost a customer for life. A product without customer service and trust is nothing but a piece of metal!!!! I will be picking another Brand that doesnt use A&E. Maytag you have lost my trust and you cant buy that back.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

Although we have always had Maytags, this was the first time we purchased a front load washer. The Maytag Neptune washer smells and your clothes stink. We have purchased the most expensive laundry products, washed and rewashed clothes and have no other recourse but to buy new machines again. We will not be purchasing Maytag or Whirlpool. I would give it a minus 5 stars.

We purchased this machine (Bravos XL top load washer) in August and its been nothing short of a disaster. It doesnt clean anything. Within two washes my cloth diapers were unusable, loaded with ammonia and stains. Our camping clothes wreaked of smoke. I tried multiple cycles, more detergent, less detergent, larger loads, smaller loads. Doesnt matter. It doesnt clean. I called customer service within a week and waited 6 weeks for a service call. Into third trimester of pregnancy and recovering from an MVA, I was washing soiled clothing by hand in bathtub desperate for help. I only wish Id known about their 30 day money back guarantee. After many calls, no shows and cancelled appointments, the first tech comes. He tells me the machine is fine. They just dont clean well. Hes not surprised. I call the appliance shop, they said the same thing. That they wouldnt have sold me the machine if they knew I had dirty laundry to wash. (Who washes clean laundry?). They wont help us. We call Maytag back. They send another tech. He says the same thing. Tells us to keep complaining to Maytag. I call again and they tell me that if I want a service tech, I have to pay. Theyve deleted all my feedback from their social media site and refuse to provide any assistance. The machine is nice looking and makes big promises but thats where it ends. Save your money. Youll get better results with your grandmas washboard.

I purchased a Maytag Bravo xl washer & dryer for $1600 in May 2017. Sunday, the user interface panel went out in the washer. After an $85 diagnostic visit, we were told it would be $500 to repair and take an additional 5 days. My husband is recovering from major knee surgery so I was short on choices. I elected to purchase a new speed queen and will never purchase Maytag again. The 10 yr warranty tag on the front is useless!

I purchased a Maytag Bravos HE top loading washing machine two years ago. The clothes hardly get wet enough to get clean. It leaves a residue on dark clothes and the basket goes unbalanced at the drop of a hat. Whatever you save in water, you spend on electricity because a cycle takes twice as long as a conventional washer. It goes out of balance and bangs the machine enough to walk it across a room. I purchased this machine from an appliance store, not some discount house. I have had machines last 20 years and this one is shot in 2. I will never, ever purchase another Maytag, Whirlpool or KitchenAid product again ever.

We purchased a Maytag dishwasher MDB7609AWS2 in October of 2010. It first stopped working about 2 years ago. Since it was only 2 years old, we were disgusted and decided to let it sit and do dishes by hand. About 2 months after it had stopped, we tried it on a fluke and it worked. It stayed working for about 2 years. It finally stopped again, so we did the same thing, just let it sit. Every once in a while we try it to see if it works. It just recently started working again. We are wondering, what is up with this. We are not sure why or how the sitting works, and it is ridiculous that you have to have an appliance that you cant use periodically. We were too stubborn to have it fixed or buy a new one at this level of newness. We will get by in this manner for at least another few years, so as not to have lost all of our investment in a dishwasher, but we have sworn off Maytag appliances forever.

We went to Home Depot and bought a Maytag front load dishwasher and dryer and microwave 3-1/2 years ago. The washer and dryer were put in right away. The dishwasher and microwave stayed in their box for another year due to us remodelling the house room by room and the kitchen wasn’t done for a year. We put the appliances in and the dishwasher panel went out in October 2011. The washer in April 2012 started having a failure 8 when it gets to the last spin and rinse in which takes a lot of shuffling clothes to get it to finish its cycle. Then last night, May 14th, 2012, the microwave caught fire and all I was doing was brew tea in a glass Pyrex measuring cup not to mention the fan didnt work from day one. The whole house was full of smoke and it melted the plastic. So the most I got out of 3 of these products is 3 years at the most. This is very sad that we spent this much money and it lasted less than 5 years. I am writing this to warn consumers not to buy Maytag appliances. They should last longer than 3 years and are not cheap to buy. This makes me very angry and I hope someone takes this seriously and work on the problems before someone burns up due to these appliances catching fire. Our dishwasher had a recall shortly after we installed it due to the element catching fire and we had your repair man replace it.

The microwave does everything I need and want it to do perfectly. It has never needed to be repaired or replaced in five years. We bought it on sale from Best Buy and consider it one of the best bargains we have ever made. Easy to operate, easy to clean, sleek and, for an appliance, quite personable. I find it refreshing to say something nice about an inanimate object.

My husband and I just purchased on 4/8/17 a BRAND NEW MAYTAG 4.3 CUBIC FEET CAPACITY FRONT LOADING WASHER WITH STEAM AFTER OUR PREVIOUS 15 year old washer that we both used just finally started having issues. So we decided to go new and with front loader with good brand. How sadly I was wrong! We brought our washer home, hooked it up and turned it on with 1/2 load of tiny laundry. It didnt even make it through one load! This POS started throwing error codes E1, E2, F8, F9, Suds and wouldnt drain any water. We reviewed the manual again, checked the filter hoses and detergent. All was fine but washer wouldnt work! I called Maytag 2 days later on Monday and after repairman came to look at it Thursday said it needs new drain pump and today now power wont turn on and nothing will work on front of machine, mind you this machine is brand new! I am so disgusted and angry that any company would sell this quality to anybody and at the prices they charge! NEVER AGAIN WILL I PURCHASE ANOTHER MAYTAG!

We purchased the washer and dryer pair...beautiful looking, no agitator, water efficient. Load sensing feature. TERRIBLE, TERRIBLE, TERRIBLE. WORST APPLIANCE WE HAVE EVER PURCHASED. Used it 3 times. Clothes would not rinse, left white soap residue in the folds of the black clothes, even after a second wash. Home Depot was just the GREATEST, they replaced it for us. We went with a less expensive model GE. With the agitator and full water load...save yourself A LOT OF TROUBLE, stay away from Maytag Bravos XL.

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

Well, my washer is 2 years old, yes thats right - 2 years old. And it only goes to the wash cycle, washes once and stops, wont complete a full cycle. Yes, the brand with the commercial with the repairman just sitting around because their products are so great you never have to work on them. Yeah right. And Ive seen videos on YouTube on the problem with the Maytags. So Maytag may want to look into it!

We bought a Maytag range Nov 2013. My daughter has maytag appliance and stand by maytag. We grew up with maytag. But those days are no longer. It is not about quality, it is about how many did we make, how many did we sell. I am very disappointed with my range. I tried several times to use my upper oven, in disbelief my lower oven was heating. This happened so much that I touch to make sure that the Correct oven is on. I also have problems with my knobs for my burners. I could not turn off burner after finished cooking. We had to unplug range and turn off gas, if we did not do that the burner would have remain burning. This very uncomfortable for us.I still believe in maytag. I am sure we have not talk to the right person. There is too much at stake for the company, too many complaints are bad for any business. I too am a victim, very disappointed, I wont give up. I have a warranty with home depot and they have been great. It is not their product but they sold it. I hope everyone with a lemon will get problems solved. We only want what we pay for, even manufacturer when they buy other products they want quality as well, we all do. Hoping everyone will be able to get justice. Thank you.

Not only does the water not drain properly causing an insane amount of stench of moldy water being trapped, but this washer has had nothing but problems since we got it. Error code after error code, problem after problem. So disappointed. My husband wanted an LG and I said it had to be Maytag because Maytag was the best. Thanks for making me a liar Maytag!

MVWC565FWO Maytag Top Load - Bought a new washing machine less than six months ago... extremely noisy: Clank, Clank, Clank, Clank, etc. Reviews said it was just noisy, nothing wrong with it. Last week it would not spin the clothes dry. Now when it is plugged in, it does nothing but run the pump! No lights, no water. Also the deep wash was never deep at all - barely covered a modest load of laundry. Repair coming today. Wish I could return it.

Had the washer for less than 3 months just a week before the 90 warranty was up and it stopped spinning. Called service dept. What a joke for this company that keep yessing you. Took a week before someone came out. Said washer needed a new motherboard and they would only cover it once but there seems to be a ongoing issue with their motherboard. Had to wait over 2 1/2 weeks before they would have one in stock. The tech installed it however now when it spins seems she left the top loose.

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

I purchased a Maytag dishwasher at Home Depot in October 2009. Recently, it made noises for a few months of laboring, and finally would not start.Maytag said it’s out of warranty and wanted $125 just to diagnose. Took it to my shop for $60 to diagnose and they found a faulty control panel.

Our washer, still under 5 year parts and labor warranty, wasnt functioning properly. We went through proper procedure having repair personnel first attempt to repair; waited over allotted time for replacement parts, wanted to attempt to repair again, then to replace with sub-standard model. We are now in our 5th month of being told 3-5 business days, 10-14 business days, and I was just told it will be weeks (after waiting 19 days) that replacement will return our call as they are 4 to 6 weeks behind. I have pages documenting dates, times, names, departments and excuses. What can I do at this point? What are my options?

I live alone and bought this unit for long life. After a few short not-used-much years, my washer sounded like a 747 was landing in my laundry room. I am a maintenance person, so I did a bit of troubleshooting and narrowed it down to the bearings installed in plastic on the outer tub that failed. My cost was $600.00 to $750.00, parts alone. It still worked, just very noisy on high spin.I emailed Maytag (now Whirlpool) and was phoned by Lee Ann. I told her I had all Maytag appliances in my home and was laid off and that if after the use this washer has had and it will cost this much if I do the work, I was not impressed with this company. She apologized and told me she will issue me an extended warranty for $299.00 that will cover it. I told her that without a job, I cannot make a decision so fast. She gave me the next business day to decide. I concluded it was cheaper than the part, so I called her back. I was scheduled for a repair, and the man opened the front and looked at it and said it was an outer tub bearing. He went to his laptop in his truck and returned to tell me that they would not authorize that expense and that all they would authorize was $350.00. He put the front of the washer on, then as if he forgot something, took it back off and reached way in the back and did something. Then, he reinstalled the front. I was livid! They charged me $299.00 for a warranty and would not repair! So I called back and was hung up on. Next, I called my credit card and disputed the charge. I tried to use the washer, and it made funny sounds and then filled up my home with smoke and stopped working. I called Maytag again, and he denied the repairman would tell me how much they would authorize to repair it and told me good news that they would issue a $174.00 check. I gave $299.00, and a few days later, they give me $174.00? This is why Whirlpool is destined to fail. I will never buy again, and I will wash in my laundry tub first! This is exactly why imports will rule! So Whirlpool, you got me for the last time!

Purchased Maytag Double Range MGT8720DH00 in March 2015. Within 2 months had to call gas company due to leak and service came out to fix it. Now anytime my house is closed up during a vacation or extended period away I come home to a locked range with a warning message to check to make sure that the knobs are off. Had gas company (who also called fire department) to come out tonight after returning from vacation with same issue again. They tested and said CO2 was ok, but to check reviews for similar ranges and I have seen repeated issues in reviews for Maytag products. The firemen all commented when they saw that it was a Maytag so it seemed like they have seen these issues before. Very scary to think we could be exposed to a constant low level gas leak in our home. Keeping windows open at all times is not a realistic option.

The Maytag Centennial (Model MVWC6ESWW1) washer was purchased in September 2009 and within 18 months no longer provided water at the temperature selected on the control panel. The problem started after we used a spin setting to remove water from a cycle that did not complete itself. Somehow selecting a spin cycle disturbed the water temperature control mechanism. We were advised by Sears to unplug and then reattach the electrical connection (similar to rebooting a computer), but this was not successful in water being delivered to the washer at the temperature indicated on the control panel. While there was minor damage to clothing and a waste of hot water before we realized what was happening, the real inconvenience is not being able to rely on the water temperature setting. Based upon reading comments on the internet (including Consumer Reports) concerning this washer, the public should be warned not to purchase this machine. Better still the machine needs to be recalled in order to protect the consumer.

We bought a new top of the line Maytag MGD7000XW dryer about 2 years ago. It worked great for about 6 months, thing started acting funny. All of the front console lights stay on all of the time and it ONLY dries on high heat now. This all happened after the warranty period. So fine, I was going to buy a new complete front console (CONSOLE Part Number: W10388467 $300.) as the online repairman suggested. Guess what, Maytag no longer offers the part to fix my dryer. So now I have a 2 year old top of the line P.O.S. MAYTAG dryer that cant be fixed. I will never buy from this company again (Maytag).

MER8700DH - Within 6 months, left rear burner stopped working and Maytag repaired it under warranty. Within next 6 months, and just before end of warranty, right front burner stopped working and again Maytag covered it under warranty. Within the second year of ownership, the oven was not working correctly and Maytag refused to cover it because it was off warranty. So I called a local appliance repair company who gave me an estimate of over $300 to repair it and basically advised against repair stating that this stove was a piece of junk. So I replaced it with a GE and junked the old one before it was even two years old. I filed a complaint with Maytag. At first they said they would go half on the labor, but then they said I should have bought the extended warranty and refused all further help.

I have had nothing except trouble with my new Maytag Bravos washer! I first had a suspension arm or something like that replaced along with the agitator. My water cycle has never worked correctly since it was new. I take out the clothes and half are still dry. My daughter washed her kids’ clothes in the washer while she was living with us and the stains did not come out. She thought that is really unusual since they werent stains that normally you would see left on the clothes. I went to my father-in-law’s house (they have a front loading Bosch), took her detergent with her that she used here and guess what? It’s just one washing and the stain was gone. She had washed the clothes in our washer at least 7 times trying to get out the stain. Now, we have such a loud noise that it sounds like it is going to take off. Then, the bottom of the washer started to leak. We took it out and checked it and we cant find the leak. The clothes smell awful when they come out of the wash. I dont know if it is bacteria build up. I use the cycle cleaner when I am supposed to. This is so sad. This is the first time I have had matching washer and dryer and I wish I would have kept my old Sears model that worked great. I havent decided if we want to fix it. With the price to fix it, I can buy one I might like. Never will I buy Maytag again or another Whirlpool without checking out the reports.

Dryer delivered nonfunctional. Tech showed up the following Tuesday. Diagnosis main board and one sensor dead. Tech returns following Thursday. Replacement board DOA. New dryer still nonfunctional. Awaiting new board with no functional $1100 dryer. This dryer replaced my three year old Maximus which was deemed too expensive to repair after three repairs. Please do not buy a Maytag/Whirlpool product.

I bought this Maytag Dryer in May 23, 2015. I had nothing but problems. I had 4 techs come out and say different reasons why it does not work. I had the vent exhaust clean out. Still not working, the one tech said there was not enough clothes for the dryer to sense it wet. I did a huge load, still doesn’t work. The sensor for the vent keeps popping up and it’s cleaned. I have to pull it out and in to get the signal light out. Cant turn on the machine. It still does not work. I tried contacting Lowe’s, since I bought an additional services plan. They said I have to call every thirty days for three months. That means I have to take my time out of work and wait for a tech for three months to get make a complaint and TRY to get new one. I really disappointed with Maytag and Lowe’s. I have a tech coming out this Monday, 11/23/2015 for another services call. I will never buy at Lowe’s or Maytag again. How many times does a certified tech from Maytag have to come out check a brand new dryer?

I bought a complete kitchen: stove, fridge, dishwasher microwave. Suppose to be stainless steel. All have rusted out within 6 months. Maytag does not stand behind their products. They sent me cleaners and all my appliances rusted more using their cleaners.

Washer Model MVWC555DWO. I dont like this machine. I thought Maytag is a good brand name, but I dont think so anymore. The engineers who designed these new machines with the water level saver dont do laundry. In order to get the cloth covered with water, I have to use the bulky sheet level. I have 2 jeans and a sheet that got holes in them, because the water level was not right. I would have my old machine repaired, if I have know how my new one would do. Im stuck with this machine. I dreaming that this machine breaks down soon and I can buy a new that has a better water level. My old one had water saver level too, but did a great job with the water level.

So we bought the whole Maytag kitchen appliance FZ (fingerprint resistant) series suite. That was such a mistake! Id give the part numbers but I think this applies to Maytag in general as it sounds like all of their appliances suck. Ours are 1½ year old and I already want new ones. Over $3,600 for junk. We knew it was no Viking or Sub Zero but didnt expect to flush $4k down the toilet either.The microwave is an over the range type and we have it vented to the outside of the house. The vent works like crap to remove the steam when you have a large pot of water boiling on the stove top. I can put the fan on high and barely any steam goes up the vent, most of it ends up soaking the microwave door to the point where I have to towel it off. The vent will hold up a paper towel so I know its pulling air but the location of the vent in relationship to the large front burners makes it useless. And the self cleaning is as others have already stated - A joke.We bought the fingerprint resistant SS and I would rather have the fingerprints than all of the scratches. Today, and this is no BS, I had a lottery ticket on the fridge under a magnet and I pulled the ticket because I wanted to check the numbers, well I slid the paper about 4 inches while it was still on the fridge under the magnet and now we have these fine scratches everywhere I did this. It wasnt the magnet because it has a felt backer on it, I took the paper off and slid the magnet all over the place, no scratching. I cant believe a piece of paper would even leave a mark at all. This is aside from some larger scratches that someone in the house must have used a feather duster on it or something.The French door fridge is loud and the ice maker is huge! The slide out basket in the freezer always gets cockeyed and stuck like its coming off the track. To line up the door tops you have to adjust the feet on the bottom of the fridge. I have to put ours out of level to get the door tops to line up, well this makes it look terrible in the cabinet space so you have to make a choice of what is uglier - thats just bad engineering. Our old fridge (GE) you could adjust the doors right on the bottom of the door. Its like they forgot this and said, Well you can just tip it one way or another to get them to line up, ya lets put that in the manual. The dishwasher sucks, plan on rinsing everything, even the silverware doesnt come clean. No its not our water.We are so disappointed in this brand which used to be considered very good, what the heck happened? Ship manufacturing over to China? And another thing, I highly doubt this is stainless steel. I know there is ferritic and martensitic stainless that are magnetic but Id bet all of my appliances that this is just regular carbon sheet steel with some coating on it to give a stainless steel look. All except for the range, that is different and doesnt scratch like the fridge, microwave, and dishwasher. Not sure why but probably has to do with the heat so they couldnt use this junk coating, just a guess though. Anyway it doesnt matter, all of the appliances are a complete waste of money. Poor design, poor performance, poor durability, pure junk!

Bravos XL washing machine is the worst washer I have ever used. IT DOESNT GET THE CLOTHES CLEAN! There is not enough water when filling up, and you cant control it. I put a load of dog blankets in the washer and at the end, they were in the same order as I put them in; they hadnt moved! All the stains were still there and there was soap scum everywhere. Also, while I appreciate a large drum, it is so large that I cant even reach down to get the clothes on the bottom, I have to use a stick to get them up. I am so irritated that I spent $1636 for the washer and dryer (dryer works fine but same trouble with the huge drum). I got mine from Sears online after checking the Consumer Reports which put it in the top 5 washers!!! Dont buy this washer. Waste of money. Will probably just have to throw it out and its brand new.

Failed after only 13 months with light use. I have a Whirlpool extended warranty which I had to fight to get them to honor. Then someone came to fix my washer and needed part was ordered, but part isnt available and company wont tell me when it will be. I have received 6 part availability dates so far. Whirlpool wont help. Over two months now without a washer. Ive asked them to replace machine or give me my money back, but they refused. The Whirlpool Extended Warranty group doesnt answer their phones, was put on hold for a long period.

I bought a Maytag 4452BDW stove, the more button is not working. I did my research and was not happy to see this is a common and reoccurring issue with Maytag Stoves. The expensive of the part that too often fails again along with the cost of the service man to repair it places the Maytag as low quality at a high price. I am hoping to see a company that stands behind its product by addressing this correctly and promptly. It would be a pleasure to have my faith restored as it should be by Maytag.

I purchased a gas range from Lowes - Maytag- Model #MGR8880AS in 2012. The range has been repaired on multiple occasions 11/2016; 3/2017; 5/2017. All three times they replaced the igniter and burner. On one occasion they replaced the computer board as well. (Each time they have informed me that this part was a recalled problem and under warranty). The stove is now out of warranty and having same issue. The stove fills with gas and the igniter does not ignite and does so intermittently. Maytag only wants to send repair company out at my expense. They need to replace the stove, because someone somewhere will die because of their product. I will purchase a new stove and not from Maytag. (All my appliances are Maytag). I also have a copy of my receipt and will provide if needed; I used my extended warranty through Lowes each time. I urge everyone not to purchase Maytag appliances.

My Maytag washer and dryer (5000 Series) is about 2 years old. Just as soon as the warranty ran out, I started getting F35 and suds error messages. Information found on the internet tells me that many Maytag customers have experienced the same problem. Whats up with this Maytag? Since many of your customers have experienced the same problems, are you willing to meet the consumer in the middle by repairing the product at no cost or are you building the appliances to last as long as the warranty?

Purchased a Maytag dishwasher 1 1/2 years ago and the panel went out. I paid $550.00 for this item, wanted to get a nicer one hoping it would last. Of course they only have a year guarantee for parts and Labor. Will not buy another Maytag appliance again!!!

Maytag MHWE450 washer - Purchased this front load washer/Dryer and pedestals 12-1-2011. The bearings are so loud when it spins that you cant hear anything. You have to replace the whole tub to fix it with no directions anywhere on how to do it. I had a Maytag top load washer for 15 years before this. They worked perfectly when I sold them. I thought these would be a great purchase for a lot longer than 2 years.

It is actually an older model Maytag set that I bought used 4.5 yrs ago. I am very impressed how its held up and how fresh our clothes are still. I have always loved Maytag and will buy again if needed.

I had another Maytag washer. It lasted 21 months. BB got me the BravosXL to replace it. I have had it 6 years. It is a piece of junk. Goes out of balance all the time. We are 2 ladies and don’t have heavy clothes to wash. I am washing now. I have put It through a wash cycle. The soap is still on the clothes. I am on my THIRD rinse cycle and there is still soap on the clothes. And I used less soap. Never again MAYTAG.

We bought the Maytag 2000 series washer and dryer stackable set in 2012 from Home Depot. My husband was smart enough to buy an extended warranty and year after year we renewed it. Guess what?? Year after year the dang washer broke. This machine was a nightmare! Now that the drum spider is broken they will not honor our warranty but want to give us $300 and guess what? I cant find a replacement for my good working dryer. We bought this set because we live in tiny space and needed them stacked. Maytag really put us in a corner and we have no money to replace both appliances. Horrible customer service. Horrible machines. Just a horrible situation. We dont know what to do.

RE: 5.2 CU Ft Top Load Washer, Model # MVWB865GW0, Serial # C84370937 - Purchased Jan 2019. The clothes come out terribly tangled and severely wrinkled, even when using the Wrinkle Control or Delicate cycle and occurs in every load size. Ive tried every cycle, including the deep fill and low spin speed but items are so wrinkled that whether I lay flat or hang or put them in the dryer, I have to iron them, which I never did before.

Maytag Cenntenial Washer - We traded our super capacity for the ex-large Maytag washer and we have great regrets. We posted it on Craigslist about 4 months after we bought the unit and NO ONE would buy it for $300.00 even though we paid close to $600, and only 4 months old? What does that tell you? I have had to add 5 gallons (bucket) with each wash to make sure all the soap washes out. Very loud, takes a long time to wash and just worthless. This last weekend, we tried to trade it for a used $150 agitator washer with a used appliance store and they said theyd never be able to sell it and refused the trade. What does that tell you about the washer?

The lid on this washer cracked twice. It is made out of plastic and is now discontinued. The lid cracks no matter how gentle you are with it. It is just over a year old and will have been serviced twice. The lid has to be ordered and you have to wait for a week. Maytag will not offer a new machine.

Like the other poor reviews here- this Bravos top load washer is the worst. So wish we had returned it!!! There is never enough water in the machine on normal cycle to get all the clothes wet so how in the world would anyone expect the clothes to get clean? Just ridiculous - and whoever invented this machine, plus those who tested it, need to have their head examined! Hate it so much.

Had this front loading washer 13 months when the circuit board failed. I pitched a huge fit as Maytag wanted to charge me 75% of a new washer for the circuit board replacement. Fortunately they caved. I like how well it spins out and washes well. The door gasket is hard to keep clean. Has fresh setting so clothes do not get moldy if you leave them too long.

I bought my Maytag Refrigerator about 7 years ago and the night mares have not stopped. The ice maker has broken down so many times, I forgot to count. The drip from the ice maker lands on the floor of the freezer and drips out to the floor. The cold part of refrigerator end up freezing the fruits and veggie and milk.

I purchased an LG (white) washer last year, but my husband upgraded all appliances to stainless, including Maytag washer and dryer. The washer does not fill with enough water to cover the clothes. It barely agitates them to wash. Some clothes even come out with dry spots on them at times! They smell and are still dirty when done. I have tried every setting hoping that was the issue. Normal, power wash, none work any better! Had to resort to the soak function which does not add fabric softener or drain the water completely. Thankfully I didnt sell or get rid of the LG. Putting the LG back in asap. Nevermind the mixed color finishes of white and stainless between the washer and dryer. Clean clothes most important! Piece of garbage and complete rip off!

I was having similar issues with my Maytag model MD dishwasher. The unit was operating, and then the start/resume light began flashing. Didnt think much about it since the machine continued to run. But the machine wouldnt cycle off, or rinse or dry. It continued to run, with the start/resume light flashing. When I opened the door and hit cancel, the unit turned off. Several minutes later, the normal light and heated dry lights came on, and soon after, the unit started up by itself (Twilight Zone music is going off in my head). I let it continue to see what it was going to do. It ran, and ran, and ran some more. I stopped it and secured the power to it, left the power off for a very long time. Started it up, no joy.I began reading the blogs sent in by other frustrated Maytag owners, we are numerous. I went back and re-read some of the posts that dealt with resetting the control panel. The one that mentioned; press Hi Temp. then Start/Resume about 3 times consecutively, that did the trick. Thank you for that useful piece of info. Saved me 143.00 plus tax and shipping for the new control panel (for now). I found some very helpful MOs (Maytag owners). I also found something very frustrating, with so many unhappy customers dealing with the similar issue. I would think that Maytag would put out a technical alert that deals with these problems. Instead, we get these so-called Maytag experts that magically appear on your computer screen. They ask you, what seems to be the problem. So after I described the issue, I asked the Pro, how to prove that the issue is with the control panel, or the elect. control board, both parts are 143.00 ea. (Just trying to limit my pain.) They send me to a page that wants to charge me 28.00 for the answer. What an insult. We pay 500-800 dollars for these units that should last more than 4 yrs. and some doofus is charging you for answers that saves you the consumer money and frustration. I, like many in the Maytag blog, will never purchase a Maytag product again.

I have owned this washer for three years and the smell in the entire area of my home is getting unbearable. I have used vinegar, clorox, and washer cleaner and I always leave the door open when the washer is not in use. My other complaint is that even a small amount of bleach cannot be used on clothes without causing bleach stains because it runs directly on the clothes before enough water is in the washer. The receptacle for softener also does not dispense the softener properly. I am very disappointed in this machine.

Overall I am satisfied with my Maytag Model MDB8859AWW2. I purchased the dishwasher 06/05/201. However, the door spring squeaks. It is a grating sound.

I purchased a Maytag Bravo HE washer and dryer! The biggest mistake I ever made! Three inches of water is max for a load of clothes! This is max full or actually empty. The washer was a third full of clothes and only the bottom layer was wet when it went into rinse! After pulling a calf I really wanted the top pants washed. Nope. Went in dirty and dry to the rinse cycle to spread the bacteria throughout the load. The soap was still laying on the dry clothes on top. Repair guy spent two hours and couldnt get enough water to at least dampen all the clothes in the wash cycle. I would like to see how much cow afterbirth bacteria was still in clothes. I didnt buy a machine to dry wash my clothes! I have asked for my money back on the pair through the performance warranty. Well see! I am not giving it a star as it doesnt earn one!

Currently own model MTB1504ARW, serial number 12541413GT refrigerator. The defrost thermostat broke and it is causing the device to frost over and not cool. Maytag is trying to replace the part with part number 63001051 and that part does not match the part that came with the machine. I spoke with a supervisor, Mr. ** who certainly was not a problem solver or any help, in other words, lacks customer service. I explained the installation of the wrong part may be dangerous and could cause a potential fire or hazard. He assured me this was the part available, but also said it was discontinued and I would have to find it with an outside vendor. I explained I compared the part removed and the part they are suggestion, per the part list, and its the wrong part. As a supervisor, Mr. ** failed to provide true customer service for myself and future customers who may be in the same situation, with the potential of causing a hazard for customers. The Maytag supervisor should learn to provide customer service and prevent possible hazards for customers, taking the next necessary steps or research the issue with other departments within Maytag. The parts below are evidence of the issue, the suggested part has two wires, the one from the refrigerator has three... poor customer service, at best with potential hazards to families and children. It may because their appliances dont break, according to their commercials, they just have too much time on their hands and cant provide the assistance that is needed.

Have had problems with the set since day one. Bought brand new from Home Depot. Got a great deal and now know why. Never cleaned the clothes properly, water marks on so many items, musty smelling regardless of how many times we cleaned it, horrible at removing stains, and finally not even 5 yo the motor stopped worked. The dryer has been repaired too and hasnt ever done a stellar job. Will never buy another Maytag product again!

I purchased this machine (Maytag washing machine model MVWB700VQ0) from Home Depot in December of 2008. When purchasing it I decided to spend a bit more money on the machine, thinking I would get a quality product. For the last two years and 5 months it has only been me and my wife in the house as the kids are in college. Hence, the washer has not been used as much as some would use it. Within the last two and one half weeks the machine started making a horrible growling noise (probably the tub bearing going bad) and then started to leak yesterday. I noticed this morning that there was a large puddle of bleach water coming from under the machine. I called Maytag, which is just a fancy name for Whirlpool, and they basically told me too bad. It is inconceivable that a machine that used to last 20-plus years barely lasted three with only two adults using it. When I owned my previous home in another town the house came with Whirlpool appliances which literally fell apart within 5 years. I wanted to stay away from Whirlpool; however, I did not know that Maytag was owned by Whirlpool. I have received no assistance from Maytag. I am absolutely disgusted with the fact that an American iconic company such as Maytag is producing such garbage. I am going to be forced to figure out and fix what is wrong with the machine myself. However, I do believe this subject should be looked into further and possibly a class action law suit against Maytag for bad customer service since there seems to be quite a few people with issues surrounding this machine.

If the control panel light on your Ice2O refrigerator starts flashing you will learn about the Non-Customer Service of Maytag. The problem is the High Voltage Control Board. Maytag has been aware of this defective part since 2007. At one time Maytag was fixing these at no cost to the customer via a recall. Then conveniently in 2011 the Japanese tsunami wiped out the only plant in the universe that manufactures the part.Now out of the goodness of Maytag’s corporate heart they offer the customer $300 off of a $2300 replacement (Oh, I am so grateful). It is time for Maytag (Whirlpool) to accept responsibility for a defective product and recall this refrigerator with a replacement. In the meantime if you have this problem, my advice is to go out a buy a non-Maytag/Whirlpool product since Maytag/Whirlpool cannot be trusted to stand behind their products. Please share this post with family and friends to prevent others from experiencing Non-Customer Service.

My Maytag model MMV4205BAB microwave turns on and heats when the door is closed. We paid a lot of $$ for this overhead microwave and it has not been a satisfactory product. The turntable broke within a couple of months and now this. Im afraid it will burn my house down. This is a defective product and in my opinion it should be recalled. I have read several other posts about this exact model and problem. We purchased all Maytag appliances for our new home and we have had problems with all of them. The auger on the ice maker on the freezer broke within a couple of months. The handle on the oven door broke off while the builder was installing the appliances, and the top of the line dishwasher doesnt clean the dishes. It leave deposits on everything, no matter the detergent used. Ill never purchase Maytag again!

In January 2006, we bought a Neptune washer and dryer, model# MAH5500BWW, because we thought they were superior to any other at the time. In January 2012, the washer started making a very loud noise in the spin cycle. It just kept getting louder and a technician was called in check out the problem. We were told that the bearing was going out and he found a hole in the back of the tub. He said it was not cost effective to replace the bearing and the tub and suggested that we continue to use it until we could no longer tolerate the noise. We are very unhappy with the durability of this washer, with the amount of money we paid to be going out only after 6 years of service. We have been a Maytag customer for 15 years and will never buy another Maytag appliance. We are going to replace the washer and dryer to keep a matching set and it certainly will not be a Maytag.

I bought a Maytag washer January 2016. We recently had a issue with it so I logged onto the Maytag website and found a service provider to come see what was wrong. I had to pay a $100 fee for them to come out and look at it. I was told that the transition went bad. The parts were under warranty however I would have to pay for labor, which would be $325. Called Maytag and was told because I did not purchase an extended warranty there was nothing they could do about the labor. I can buy a new washer for $500 why would I spend $325 to fix? Already lost a $100 for them to come out to tell me what was wrong. Completely not right. A washer should last more then 4 years! Do not buy any Maytag produces. Will not last!

Purchased Maytag dishwasher Model Number MDB7749AWM1 in June 2011. With a two person household, we need a new control panel in Sept 2014. Total cost of service call, repair and part is $325. This unit was a poor value for us. I see the trend is to discontinue a model after a short period of time, making it impossible for anyone to get a review of other peoples experiences. I went with Maytag because of this. It was a company with a strong reputation for quality equipment. Not so anymore. I would not purchase another product made by Maytag.

We purchased a Maytag Centennial line washer (Model # MVWC400XW0) and paid a little more hoping that it will last longer than a normal washer. After just 14 months, the washer breaks and we are forced to buy an extended warranty from Maytag for $300. The warranty price seemed a little high; however, the only other option was to buy a new washer. The repair guys showed and said it should be fixed.After just three weeks, the washer broke again with the exact same symptom. Since I had the extended warranty, I called in another ticket. A different repair guy showed up and he said the first guy messed up. He said the guy misread the diagnostic code and didnt even put in the part that he said he replaced. The repair guy checked with Maytag and they told him it was no longer cost effective to fix our washer. Really? They overcharged for the warranty and wont even repair it when it breaks. The only reason I can think Maytag would do this is that they know the washers are junk.

We purchased a Maytag Neptune series washer/dryer set approximately 5 years ago. This is the 2nd time in 5 years that we were told by our local repair person that the drum of the dryer got bent out of shape. This is from normal use and due to a bad design on their end. Maytag refuses to foot the bill (about $350-$400) as it is out of warranty.

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

Bought this (Maytag Washer MVWB955FC1) on 1/8/18, was delivered late in January as it was on back-order. On 4/30/18, during a cycle, the washer made a pop sound. There was glass everywhere. The glass had shattered and exploded onto the floor and washer. The glass is on the inside of the drum and all over the clothes. Contacted Maytag and they sent out a repairman the next day. Repair said there is a point of impact indicated I dropped something on it. NOTHING was dropped on it. There is a point of impact, from the inside. The glass is pushed up and out indicating pressure from INSIDE the washer.Repairman says its not covered under warranty and that I had to pay for his time as well. He also said there are no known issues with this lid and washer. The lid is out of stock and wont be available for a while. I called Maytag and they gave me the same response, never heard of this.. and lid is out of stock. I found SEVERAL reviews/complaints in which, for the exact same model, this has happened to other people. This glass lid is dangerous and poses a serious safety risk to households that contain it. If they replace the lid, there is no guarantee this will not happen again. A child could walk by the washer and at any moment the glass lid could explode, send tiny shards of glass everywhere. I want a refund for this dangerous washer.

I think that I finally figured out a way around the piece of junk Maytag sold me. I bought a Maytag french door, stainless, yada, yada refrigerator in 2006. When it broke down, see later description, the first several times it was ok because of the warranty. This POS has failed 7 times requiring $300+ to fix every time. When contacted about the issue, the people at Maytag seem happy. The business model is working perfectly. There goes another sucker. The refrigerator begins its eventual breakdown with the door alarm light and sound beeping constantly. Beeping that continues for days and weeks. The next progression to failure continues with it not beeping anymore but now the interior lights do not light when the refrigerator is opened. Finally, the refrigerator stops cooling entirely and it is dead.Now, Maytag no longer wants anything to do with it so you need to call a repair man. When the repair man arrives, the entire time he talks about what a piece of junk Maytag is. They, every time, at first think it is the switches and replace them. This NEVER fixes the issue. Next, they have to replace the computer brain. $400 to fix. EVERY TIME. Now, at least every year. If you buy Maytag and have a similar experience, get your wallet out. Sell you junk then dont stand behind it.

Maytag Centennial 3.4 top-loader was purchased at Home Depot. It has never worked yet. On 4/28/12, the third weekend, I sat home for the servicemen to fix this junk machine. The first two times, the machine didn’t work ten minutes after they left and today they went to the wrong address. I have much more important things to do than to sit around and wait for someone to figure out what is wrong with this machine. It would have been cheaper for me to junk this brand new machine and buy a washer from a company that makes washers that work!

To begin with, the Bravos 300 washer was bought because we owned a Maytag previously and it was with us for 25 years. It was still running when we gave it away and the only problem was a small oil leak starting at the drive. The new washer has no agitator, just the new style flat thing at the bottom of the tub. You cannot wash a set of fitted sheets without it turning into a tangled mess. The washer quit working after about 5 years and all indications pointed to the control. The control would reset after unplugging, but would freeze immediately when you tried to enter a command. We live in an isolated place and it is not feasible to fly in a service person. I ordered a new control, but there was no change in function. After several hours of detective work, it turns out that the mickey mouse plug for the electrical connection at the pump had broken inside. Because the pump would not work, the whole control would freeze. We will never buy another Maytag.

Maytag Bravo Quiet Series 300 - I purchased the set 2.5 years ago and after 2 years, it started making a rubbing sound. I kept using it with having a family of 5 and this is why I purchased it in the first place; with 3 boys, I do a lot of laundry. It then quit working on me all together and wouldnt spin the clothes. I had a technician come out and it was the barriens that spun the drum so I had them fix it and it cost me $400. Then about a month later, it was flashing code F51 and not spinning. I had them come back out thinking it would be covered since it just got fixed but no, it cost me another $100. Now, 6 months later and here I am again unable to do laundry because its flashing F51 and wont drain or spin. I called Maytag and they tried selling me a warranty and said it wasnt recalled because there wasnt enough complaints. We need to all call and raise a ruckus. This is ridiculous. Sorry to hear everyone going through as I am.

Ive had my washer and dryer since 2007. We purchased a new vacation home and it was included. I used the HD washing machines at my daughters, though hers was a front loader from a different company. Im unhappy with mine. Would not purchase one again. I find my clothes arent clean and my kitchen clothes and towels always have a residue on them. I now wash everything on warm, use the proper amount of soap and have to do heavy load cycle. Im still not happy, but it beats buying a new one.

Purchased a Maytag Bravos washing machine. DO NOT BUY THIS MACHINE. Disaster as the cycling is hit and miss. The clothes can take 4 hours or more to wash a load. And even then the clothes may still be soaking wet. Grandmas old wringer washer was better. DO NOT BUY MAYTAG. DO NOT BUY MAYTAG BRAVOS.

Maytag Bravos washer MVWB750WQO frame assembly and cabinet rust - I sent letter of internal and external rust issues to Jeff Fettig (Whirlpool CEO) and received no response. Then, I sent letter a second time with an attached signed receipt. Then, I finally received a call from corporate staff member stating they would replace parts but not labor. Labor costs would cost between $350 - $500.00. This is without the initial service call and diagnosis cost between $100 - $125.00. The determined parts list cost would be $700 - 50% for Whirlpool internal cost + shipping be approximately $425.00. This is more than the cost of a new unit or the value of three-year depreciation value of the existing unit. This does not make any financial sense. Whirlpool should provide a new replacement unit at their costs. It has been three months and with no successful outcome. Also, via web research, there are many complaints about Maytag/Whirlpool and I am not the first in regards to rust issue. Therefore, Whirlpool is attempting to limit their financial exposure by only offering parts that they have to agree upon because the labor costs will not support this additional investment in a three-year unit. It makes more financial sense to purchase new or be offered a replacement unit.

My dishwasher is less than 2 years old - has only been used a total of less than 12 months as I am seasonal in Florida. The control panel has failed. It will cost $275 parts and labor to fix.

My husband and I purchased the Bravos XL washer and dryer set about a year ago as our first big washer/dryer purchase for our new home. We spent about $1200 on the set from Home Depot. I very much regret this purchase as the washer never gets our clothing clean! The washer never puts enough water in the basin and the clothing comes out with strange white smudges EVERY. SINGLE. TIME.I have tried changing detergent, I have tried skipping fabric softener, Ive tried rinsing out the dispenser thinking it was residue from old soap. I dont know what it is, but what I DO know is that the clothes go in without the white smudges and come back out with them for every load. I have to run a second rinse cycle just to get it off, which means Im washing for at least an hour and a half. I DESPISE this machine and its costing me more on my water bill.Additionally, the dryer isnt much better. It constantly shuts itself off even when its not on energy saver mode, with the little red light going on for air flow. Ive checked the connection and dont see what the issue is. If I have a big load such as blankets in there, I have to dry them all individually for almost an hour just to dry my bedding! It simply wont stay on to dry a full load. I very much regret my purchase and wish Id gone with something simpler and cheaper as it would have done a much better job with my laundry. Lesson learned. Dont waste your money on Maytag.

Approx four months ago we got new stainless steel Maytag fridge, stove and dishwasher. Terrible, terrible, terrible. The dishwasher rack was broken, and the parts are plastic and hardly any room on the racks. The fridge had the wrong hinges and doors on them. We have been waiting for four months to have them replaced. Today we checked with Maytag and still not coming. The fridge makes a very loud humming noise it almost shakes the floor. This was some sort of compressor problem. Now the fridge is having problems with the freezer. It is freezing up with frost everywhere. The stove is terrible. I waited an extra month to get a convection oven which I have had before and this one is terrible. The double oven is a great feature if they work. They take forever to heat and if you do anything with the food you have reset the temperature? The top is the worst for cooking as the only one that works fast is the boost but then it slows down and you have a hard time cooking the food. The black top is very very hard to clean. I have owned a Maytag washer and dryer for the last 34 years. They have been excellent. Since Whirlpool took over Maytag they seem to have run the name into the ground and all the good service and products they had built up are now ruined. I told my neighbor a few years ago to buy a Maytag washer and dryer and they did. They have had nothing but trouble and are now having to buy new ones but not Maytag. It is a shame that with all the technology that Maytag has built up over the years is now gone. If you look at all the terrible reviews I dont think Whirlpool will be in business much longer with products and service like this. I still have a fifties fridge for pop and beer and it is the best fridge ever with no problems and my last fridge in my garage, that I replaced with this Maytag is still better than this new fridge. The service man that came to fix the fridge said we had to build in the fridge to keep the noise down. How come they never had problems with Maytag products years ago. I feel its all about the almighty dollar. They only last a few years and you have to buy expensive warranty. If you made them properly you would not need warranty and they would last for years like before. If anyone knows if there is a class action suit against these companies let me know since all of us should not be ripped off and costing us time and money.