My wife was in the kitchen and started yelling for me to get in there fast. I could smell smoke and then could see the smoke in the kitchen and sparks coming out of the front top right side of the dishwasher. I shut off the power to the dishwasher at the breaker panel. I then removed the contents and then the dishwasher itself. I threw it outside and then the next day I took apart the door and found that the control board was melted and fried. The model # is MDBH949PAM1. We are trying to locate the receipt for date of purchase. Pictures are attached. This is not safe and my wife is very upset as our 4 year old daughter had been leaning on the door not just 15 or so seconds before this happened.

I purchased this Atlantis dryer several years ago. To this day, I have replaced the rollers and drum three times. What a piece of junk! This will be the last Maytag I ever own.

We purchased our range in May of 2012. It is now November 2014 and the stove has had three brains, three ignitors in the oven and one ignitor in the back of the stove. When I set it to bake at 350 degrees, the oven heats up and I put the food in the oven. When I go to check the food, I find the oven stone cold and the brain is still displaying 350 degrees. According to Home Depot Warranty department, if the oven has been fixed three times for the same problem, then the unit is considered a LEMON. Ok, what about the three brains? What about the three ignitors? The ignitor in the back of the stove controls the oven as well. SEVEN times for a technician to come out and fix my LEMON stove is ridiculous. California has lemon laws. I will file suit against Home Depot, Whirlpool, A&E and Quality Appliance if this stove is not replaced within the next seven days. IT IS A LEMON! I have lost way too much food in this oven because I dont know when it shuts off.

Have been very disappointed. The burners keep going out. The repairman said a bug could crawl on the element and break it. Then the temperature on burner on it works from med to high and any lower no heat. The dual burner is now backwards. The oven handle keeps falling off. Worst range I ever had and I thought it was a step up to Maytag.

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

I have a gas dryer from Maytag that works very well. Very easy to use and economical using it with propane. Im pleased with my purchase. Ive had it now for about 8 months. I would recommend buying another one.

I bought my Maytag dishwasher in February 2011. It seemed like a good model - basic functions, upper spray arm, stainless interior. Well this dishwasher has been all downhill since I got it. First it is cheaply made. The racks and plastic stoppers on the racks immediately started falling apart. The one year after we installed it the front control panel went out, rendering the dishwasher completely useless! The warranty had just run out! To my pleasant surprise, I received an extended warranty offer from Sears. Had the front panel replaced and it started working again.... but apparently it is a bad design and it is likely to happen again. After reading online I am not the only one with this problem.Now another year later we are having a the sprayer on the top and the back hose replaced..... (still waiting for sears to install). It makes grinding sounds, leaves white marks, doesnt clean.... it is a non-stop battle with this product. Upon calling Maytag, they said they could give me advice but cant pay for any parts or even give me a coupon towards a new product! I have tried everything with this dishwasher - fancy soap, cleaning solutions, jet dry... its not me, its Maytag! I will likely be in the market to buy another dishwasher next year because of all the issues, and it for sure will not be a Maytag.

Great stove for the price. The oven bakes good, the self-cleaning oven is awesome, the top is easy to clean up and regulating the temperature is so easy.

I bought the matching Bravos washer and dryer 4 years ago. I always bought Kenmore appliances but decided, based on the then reviews, that I would upgrade to Maytag. Biggest mistake I have made! I am a very tolerant person always looking for the best in anything. But I have to say, I hate both the washer and dryer. My clothes are faded, they shrink in the dryer even on delicate. I really cant say anything good about them. Today I washed 2 twin sheets, one king top sheet, and one very thin blanket. When I opened the washer, one twin sheet was on top and not even wet. So now I get to run another load and have to wait to remake my bed. When I have washed rugs on bulky, they are filled with soap when finished. Half the time, it doesnt spin out the water and I run a second and third spin cycle on a variety of items. I avoid doing laundry because it is so frustrating. I am retired so I cant afford to replace them. I just dont want anyone else to suffer the same frustrations!

I bought a new stainless steel Maytag refrigerator last year. It had a one-year warranty. Wouldnt you know, 14 months after my purchase, the icemaker stopped working. Did not take out the extended warranty, as I thought I had purchased a quality appliance. I contacted the store where I purchased it. Was told it would cost $150 to replace. I have a feeling this appliance wont last very long. Suffice it to say, I will never purchase another Maytag appliance.

I purchased a washer on 8/13/12. I had it installed on 8/20/12. It did not clean clothes properly. I went to Two Guys and they said they dont take returns and told me to call Maytag. I called Maytag and they sent a a service agent to check the machine on 9/10/12. They said the machine codes were imbalanced and over stud. They need to recalibrate the machine. I did laundry the same day and still find clothes do not come clean. I need to return the machine. I called Maytag and was told they dont take returns. This machine is not cleaning clothes as it should be and I want a refund!

Maytag Washer Model#MVWC465HW2, just purchased it 1/30/2019, leaves white stains on dark colored clothes. I use liquid soap. I don’t use softener nor bleach. I use OxiClean on my whites and sheet softener in the dryer. Someone please out there help, I can’t return it, it’s past 30 days. I have extended warranty but they can’t help. It’s not broken. I hear a lot of bad reviews/complaints, but no answer if it’s been solved or how to solve it. Please someone help???

This machine is awful and a waste of money. Don’t trust the reviews with “workarounds.” That’s crazy! Doing laundry is difficult enough in my house so I need to add extra work? And they don’t work anyway. Water is barely 1-2 inches deep. But the real issue is the clothes don’t come out clean. Of course, they smell clean because all the soap hasn’t rinsed out but they are not. I spilled coffee on a white tee. Dabbed it up with a wet napkin. Threw it in the laundry. Did whites and added extra bleach and extra water because I know how much this machine sucks. Not only are my clothes yellow but the coffee stain is still there. I can’t imagine how it will wash tough stains like blood and wine and grease. I cannot even believe they are allowed to rip people off with this product.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in 2014. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within warranty. Then another valve got stuck about a year ago and the third one got stuck about a month ago. I am going to replace these two valves now. My friend, who is helping me replace, has similar gas range. He also needs to replace a valve. His range is about a year old.

Purchased a Maytag washer and dryer 6 years ago and everything was fine until 3 weeks ago when the washer stopped spinning. We knew we were out of the 1 year warranty and contacted a repair service, who told us the bearing was no good. Contacted Maytag who offered in goodwill to pay for the parts and we would pay for the labor. A different repair person came in and told us the washer has no bearings but a transmission, which went bad. They ordered the transmission and today the repair person was in to install it. He installed the transmission, but while trying to take out the old one he dented the drum. According to my husband the repair person banged so hard that it sounded as if something could have been damaged, sure enough it was the drum. Contacted Maytag to see if anything can be done as now we still have no washer, and the repair person was their selection not ours. All we got from Maytag was they are not responsible and there is not much more they can do. I cannot believe the last Maytag product we had lasted over 20 years and this one is less than 6 years with problems. Will not purchase another of their products again.

Bought this machine with the intention of having at LEAST 10 problem free years with it. Its a Maytag after all. Not an unreasonable expectation. Within the first 2 years, the machine sounded like the bearings were going out (heavy, grinding noises when it shifted gears). Repairman came, replaced the entire drum (only way to get to the gears, I guess). Didnt fix a thing. Then the rinse and spin cycle on ANY wash cycle randomly quits. Just stops. Full load of wet, soapy clothes, sitting in the tub while an LD error code quietly flashes.Its not uncommon for it to take two full days of screwing around with this machine to get one load of clothes done. Have to UNPLUG the machine, let it sit for about an hour, and try again. It is the biggest waste of money ever and I will NEVER buy another Maytag nothing. Contacted Maytag and they recommended I call a repairman...REALLY? REALLY? Gee, I wish I had thought of that. Repair guy has been to my house so damn many times for this machine, we are now friends on Facebook. Dont waste your money on this machine.

We purchased all new appliances 3 years ago including a Maytag dishwasher. Same problem as a lot of others. We had the control board fail three times in just four months. Now today the repairman came and while he was here contacted other Sears technicians and Whirlpool technicians. They came up with the idea to replace the detergent dispenser which they said is causing the main control board to fail. However, while the tech was on the line with Sears and Whirlpool they done troubleshooting on the detergent dispenser and found that it was all within specifications. In fact, that was not a problem because it worked as it should. But in their wisdom they decided to replace the detergent dispenser. We now have to wait another ten days for the part to arrive and reschedule another appointment to have the detergent dispenser that works replaced. The serviceman that was at our house said that they are making him replace a part that is working and that this does not need to be done but he has to take instructions from Sears technicians. Our service person said that he doesnt anticipate that replacing the detergent dispenser will make the dishwasher work but he said if it does it will only last a few weeks as before and then fail once again. We have the dishwasher on extended warranty and there are about 22 months. I suspect that this one will be going to court to get resolved. Never Maytag again or Whirlpool.

I moved into my home in July 2013. My kitchen came with all stainless appliances that appeared and seemed to be in excellent shape. I have been using the Whirlpool Microwave oven to heat foods (all in microwave safe) containers and dishes. This morning, I was heating a muffin, when suddenly I hear popping. When I looked through the glass into the inside of the microwave I saw sparks then flames. I immediately stopped the microwave. The fire apparently started in the area of one clip that holds the metal rack inside. In researching this issue online, I found hundreds of complaints from people who have experienced the same issue, and Whirlpool refused to replace the unit because it is out of warranty.

DO NOT PURCHASE UNLESS you want dirty clothes that smell.... Water level not correct, binding laundry together and replaced the same parts with cheap parts over and over... just wanted clean clothes in a no frills washer. NOT with this washer. Owned it 3 yrs and disliked it the first half washed load... $869.00 heap of junk.

Never liked this machine. No flexibility in settings, ruins clothes, noisy and often shuts down. But main concern in the fact the whole top is rusting by the bleach dispenser and it leaks from the top all over. It is only 3 or 4 years old. Can not believe an expensive product like this can be so bad.

I purchased the Bravos X washer approximately 13 mos ago. Washer was noisy and has deteriorated since installation. I questioned the ability of a non agitator appliance getting close clean but was assured it would. Not the best if clothes are just moving against clothes. The machine had a difficult time in between adjusting to wash balancing a 3x event upon starting. It leaked intermittently during spin cycles and stopped due to unbalanced loads, sometimes refilling and stopping again. Now it wont spin at all, circuit board problems! This is my first and last Maytag. The company will most likely not balance/compensate on the purchase price (like the Bravos X) because it is beyond the 12 mos warranty.

Model MFT2776FE200 worst purchase of my life! We purchased the Maytag French Door Refrigerator last year. Within a few months, freezer failed and we had to have a retrofit done. Less than one year it has failed again. No refrig for over one month and still no parts. Hundreds of dollars of wasted food and I’m asked by Maytag Service if I have an extended Warranty. I didn’t realized that a new refrig needed to have an extended warranty. Will NEVER purchase another Maytag product again. We are devastated that spending 3k on a fridge means you might as well throw your money to the wind.

I have trusted Maytag for many years, more than 60 years, my parents and then myself. My Dad always told me I could trust Maytag over any other brand and that has always been true until I bought a new Centennial Econoserve Washer. This is without question the worst machine ever made. I should have asked every question in the book concerning this machine but, oh no, I just trusted the name MAYTAG. I am so sorry. I cant trust it to clean anything that shows it needs cleaning so you have to wonder what does it clean that you cant see. Im sorry people, I just dont know what to do. I cant afford to buy a new machine and the store I purchased are basically telling me, Sorry, you bought a stripped down model. Too bad! I will never buy another appliance from that store nor will I recommend them to anyone. Too bad since they are locally owned. Anyway, Maytag, you blew it badly to turn out this terrible machine. Thats my story and Im sticking to it. Better product next time.

No problem with retailer. Problem is this top of the line Maytag dishwasher, Model# MD8895lAWW. Stinks all around. Takes long to wash and load, times are far apart and too few so holds few dishes. Dishes and glasses break because of the tine spaces. Horrible dishwasher for high price. I hate it so much it upsets me daily. All I get is a sorry from Maytag. Its not that old, only a year and a half. Why no satisfaction? I will avoid all Maytag products for life.

I have an MFD2560HEB refrigerator that I purchased 6 years ago. I paid a premium price for what I thought was a quality product. It has had issues with the ice maker from the beginning, yet I was always able to get it fixed with unplugging the unit for a while. The fan inside the unit stopped working last year. I took apart the entire inside to replace it, and now, 4 months later, the water is completely frozen. Unfortunately, I purchased a Maytag induction stove in May and less than a month later, it is not working either. Maytag quality is not! I asked if I could return the stove, but was told I had to let them fix it. Im still waiting to use my $2,000 stove!

We purchased the Bravos XL washer just over a year ago. It is being replaced 1/10/2017. Simply put this is the worst product I think I have ever encountered. Extremely noisy wash cycles leave residue on the clothes, clothes do not get wet in some spots. This washer is so noisy you can hear it from outside. What an embarrassment. You have to run the clothes twice first with detergent and again without detergent to remove the residue left over from the first wash cycle (not energy efficient at all). If I could give a minus score like minus 10 I would.

It went bad, then I called a technician who replaced the compressor. After a few months, it broke down again after I had bought new parts for it. I was very dissatisfied with how the refrigerator was built. I spent lots of money on it, and it wasnt worth it.

This washer was the biggest disappointment I have ever had. When I looked at it in the store I was excited that the tub was so big and the Maytag Label has always been trustworthy to me and my family. This machine certainly has disillusioned me against Maytag. I can only wash clothes on the bulky sheet cycle because even with deep water wash it only puts about 2 of water to wash clothes. Clothes on top dont even get wet! It doesnt take an engineer to figure out that you cant wash clothes without water. Big mistake! Would never recommend this washer to anyone! I complained directly to Maytag and never received a response. I have had to rewash clothes because they did not get clean. Even with an extra rinse the clothes still have enough soap in them to make my skin irritated. My whites are not white even though I use hot water and follow all of the directions provided with the machine. If there was any way I could afford it, I would throw this machine out to the garbage and get one that actually cleans the clothes. I will never buy another Maytag machine in my life. 

I purchased this range from a Maytag outlet in Nov. 2006. No problems with it until Nov 2015. The oven igniter failed. This was serviced locally and replaced in an efficient manner by the local service tech. All is good until 2 days later when I decided it is time for an oven cleaning cycle. I set the cycle for Medium Soil (3hrs). After the conclusion of the clean cycle, the oven (bake) would not work. Called Maytag service, the service tech replaced burned up oven wiring as well as the igniter again. However, the cleaning cycle had taken out the gas safety valve control as well. I am now told there is no replacement oven gas safety valve unit available anywhere. I even called Maytags 1-800 number and searched online only to find the part on backorder and not available.I find this particularly frustrating in light that I spent over $1200 on a Maytag product I thought would bring way more than 9 years of service before it is deemed unrepairable. The average gas range lifetime is 18 years. In my opinion, not a good return for the investment. Its a shame because the rest of the range works and looks fine, which is now destined for the dump. I am replacing the Maytag with a $550. Frigidaire with manual cleaning. Will never buy another Maytag appliance or a self cleaning oven again. If the self cleaning feature has the potential to fry the controls, why would they offer such a feature, or why couldnt they warn one of the potential failure.

This is not about a Bravo but Maytag is the biggest piece of junk Ive ever owned. Have not had the washer but a couple of years and is leaking somewhere inside of the machine. Have to turn the water on and off just to wash clothes and still laundry room floor soaked. The dryer I have to run for 70 mins. on high heat at least twice to dry clothes, 3 times for your towels. Of course it lasted long enough so the warranty had run out. Never ever again would I buy this crap.

Bought a Maytag Bravos XL washing machine because I thought it was a dependable brand. We have had it 14 months and the lid (upper left corner) will not stay connected. I called Maytag and the rep states to me Is it broken in the upper left corner and I replied yes. He continued he is just the parts guy, but every bravos has the same problem. I asked for the replacement part ($302), but he said the part is on back order for 60 days. He continued that maybe I should buy two because it will happen again. I only paid $700 for the washer, but it should never break down after 14 months. I highly recommend a different brand.

I thought it was just my machine that sounded like an airplane taking off in my laundry room. Upon reading these reviews I see there is a real problem with this machine. My parents and grandparents trusted and swore by Maytag products. Maybe then, but certainly not now. Maytag for me stands for landfill. I have had 2 Maytag certified service companies come to repair my washer that is only 6 years old and its the same part both times which I am told by these service providers has been a problem and Maytag knows about it. But when I call Maytag all I get is some sound bite advising me there has been no recall and since I have an extended warranty I will have to take it up with them since that is who my contract is with. Of course they are only obligated to make a repair and cannot replace a defective unit. Of course not.Far be it for Maytag to step up and really stand behind the promises they are making all over our television channels with the new Maytag man. The top of the washer is also all rusted out around the soap, bleach, and softener openings. It is a poorly made machine with known issues by a manufacturer that I will never buy from again. Its a sad day that manufacturers are not held accountable for inferior products and even sadder that this Maytag manufacturer boasts its made in the USA for this machine. So is it back to China we go??? If you want America back you better support your product to your buyers.

I have a stainless steel dishwasher, model MDBH985AWS10. Its about 5 years old. The control panel works intermittently -- Ive replaced and ruled out the door latch -- now Ive got the problem narrowed down to either the control panel or the circuit board. Ive read about this diagnostic cycle I could run to try to help diagnose the problem. I emailed Maytag for the code and waited a week and didnt get a response.I called them today and they said they cant give me the code--they only give that to their technicians. My dishwasher is not brand new, but I paid good money for it, and Id prefer to not have to guess what to buy when Im trying to repair it. Each of these parts costs about $150. Im not sure what the policy is for other dishwasher manufacturers, but for the next washer I buy, Ill find a company that either 1) has more reliable products or 2) at least tries to help the customer repair his own equipment.

I bought a Maytag dishwasher (Model: MDBH949AWS2) from Home Depot on 07 April 11 and it died 24 August 11. I called Maytag to set up an appointment for repair. The repair person showed up and stated that the control panel needed to be replaced. Apparently, if moisture gets into the panel it shorts it out. One would think that when designing an appliance that utilizes water and creates steam, it would be sealed. Anyway, the repairman explained that because the dishwasher was in a residential program, the warranty was null and void. I wish that someone would have explained this before I purchased it. I went online to AppliancePartsPro.com and ordered the part for $100.75 including the shipping cost. Then, I went back online to look up how to install the panel. The repair person said that they are charging $133.00 for the part and $129.00 to install. A small star tip screwdriver and 15 minutes was all it took to fix. From what I have read, this will not be the last control panel but, at least, I know how to fix it. Another thing that I know is that Maytag is off my list of future appliance purchases regardless of where Im using them.

I share the complaints of others about the Maytag Bravos washer (model MVWB300WQO), which I purchased in October of 2009.Besides being overpriced, its a washer that doesnt soak clothes, develops a bad odor, has silly things like unnecessary lights and music, and you cant add an item once the wash cycle has begun without the cycle starting over from the beginning. It also leaves washed items in twisted wads and the lid locks so you cant see whats going on inside. In addition, it damages items. Ill have to replace a full-sized blanket that it recently destroyed and now I cant trust that itll wash things safely, which is a problem. The person I spoke with at the companys customer service department simply said that I shouldve used the bulky item option instead of the regular cycle. I explained that Id used the bulky item cycle before and the same thing happened. The washer leaves larger items stretched very tightly across the tub and I suspect that is how my lightweight cotton blanket was destroyed. She offered to schedule someone to service the washer. But its not broken, its a poor design, so sending someone here would be a waste of time.

Sears washing machine model # mvwx500xwo - This machine is the worst. My mother who is 87 years old smells like mold every day due to the smell that comes from this machine. Im not sure whats going on but the plumber told us there is something very wrong with this machine. Its not the hot or cold water that smells, its the machine. I am now concerned about my mothers health. Please advise if you will allow us to purchase another machine with some kind of a credit due to the serious issue this machine has.

Purchased this maytag oven from home depot November 2011. Oven has been working properly since install. The top burner controls do operate too easy and you can just brush up against the stove and turn the gas on which I seen here was mentioned. My major issue is the stainless steel finish that was applied. It appears that this metal was not properly prepared prior to applying the finish. The oven door is with rust blisters. The metal under the coating is causing this problem. The finish in the other areas is with no problems... No chemicals have been used to clean this oven.Customer service of maytag stated that this stove only has a one year warranty... so if you buy any maytag just remember one year and when it breaks down the cost to fix will be more than a new defective maytag stove. I will not purchase another maytag product and I do not recommend that this manufacturer be considered when purchasing any appliance.

We loved the YMMV4206 microwave - at first. After the warranty was over, we started having issues where we would put the food in the microwave and try to enter the time, wed get the message to open door and close door. Wed try that and for the next few months it would work. At the 18 month mark, thats all it would do, was tell us to open/close door. We ended up unplugging it and it has been unusable since before Christmas. When I call Maytag and related to the support staff our problem, they were of the attitude that it is out of warranty and we can send someone out to take a look at it - for $130 + HST without even repairing it, that would be to diagnose the problem that we already know, then we would have to wait for them to order the part and come back. Do Not Buy this product.

The engineering of all these new machines are totally useless. Bring back the old tech. They DRY wash, NO WATER, they take forever to finish, wasting energy, clothing not cleaned. They are very noisy, doing nothing. Time to recall all of these units. They are totally useless.

I saw something on your website about Maytag Neptune class action suit back in late 2005. I have owned one, never was notified of the settlement, and saw this since I have a mildew problem also in my washer. They are not willing to do anything about the repair on my machine, but send out someone and make me pay for it. Since I bought it in 2002, I would want to know why was I not included in the repairs and why wont they honor me in this since I am the machines original owner. Help, I worry that I am not having clean clothes and it is contributing to illness due to mold spores!

Maytag in general has gone from being reputable in the early 70s to being the epitome of a rip-off company that sells junk, then refuses to stand behind it. I have a Maytag Washer and dryer. The washer continually goes out of balance and spins across the floor. Repair people tell us that our floor is not strong enough - funny, our new Samsung washer has no apparent issues with the floor or anything else. Our Maytag Gemini is a piece of crap. The ovens do not work or heat up most days. Maytag pushes replacing an EOC board at $800.00, but then the part is not available. Stove is not even six years old. Maytag is a synonym for junk.

You would be better off going to the river and washing your clothes with rocks. Piece of junk. Maytag will have you believe that the six inches of water this washer uses to clean a comforter is enough. I would like to know which individuals in the dept of energy thought this water saving feature was a novel idea. What use is a giant washer tub if it doesn’t have enough water. Sorry Maytag, my clothes used to come out clean with your old model, now I spend hours trying to figure out ways to get this washer to clean. Currently I am using the clean washer cycle for my comforters and then using the deep water cycle. So it takes about four hours to do a load of clothes. Thanks Maytag! This Maytag Bravos XL washer stinks.

Our Maytag microwave, which we bought based on Maytags supposed quality, is nothing but a piece of junk. In two years it has had or needs repairs that nearly double the original cost! Thats ridiculous. We are done with Maytag and are not going to get suckered into their Whirlpool/KitchenAid or other brands. So long.

I purchased a Maytag dishwasher less than 2 years ago through Home Depot and did not purchase the extended warranty. The start button has stopped working and is not lighting up. I was referred by Pacific Sales, the appliance sales company at Home Depot, directly to Maytag to schedule repairs which I am willing to pay for. After a nearly hour long call between hold times and conversations I was told the service would be scheduled for Thursday or Friday of this week. As we were scheduling the appointment, I was told the computer for scheduling had gone down and to call the next day to schedule. I called next day and spoke with a customer service rep who said there was no record of my call the day before. I gave her all of my information, then she transferred me to another service person who then had no record of my two prior conversations. After giving my info to the this 3rd customer service representative, I learned that a repair could not be scheduled for over a week. I asked to speak with someone about my complaints and was told there was no one I could speak with but that she would pass on the complaint. I asked for a return call or email to confirm that my complaint was received and she said that I would not get that. I then asked for a free service call because of their poor customer service. This was of course denied. The dishwasher has been fine for the short period of time I have owned it but I wont buy another Maytag because of their poor customer service and because the dishwasher has a problem in less than two years. I am just writing this as a warning for other potential Maytag customers.

On May 11, 2010, I purchased a Maytag washing machine from Lowes. On June 22, 2011, the machine wouldnt empty out on the rinse cycle. Lowes was called as the machine was only one month out of warranty. They dispatched Appliance Plus for a service call which would be $80.00 just to diagnose the problem. It turns out the machine needs three parts - a timer, an ATC switch, and a rinse switch. All totaled, this will add up to over $300.00, plus the $80.00 for the service call.Appliance Plus tried to contact Whirlpool to see if Whirlpool would at least pay for parts, being it was only one month out of warranty. The answer took 5 days and the request was denied. I was told I should contact Lowes Service Advantage and maybe they could contact Whirlpool for a special consideration, again, being it was only one month out of warranty. I made the call and they said to give them two business days turn-around for an answer. On June 30th, Lowes said Whirlpool was looking for the serial number and I provided it. They told me to give them another 2 business days turn-around. On July 3rd, I again called Lowes and they informed me that they still hadnt heard from Whirlpool. Finally, on July 7th, I received a call from Lowes saying Whirlpool denied the request.

I purchase my first glass top stove; a Maytag. It came with a 10 year warranty on all elements and the glass top. As this is a first glass top I read through all instructions, there appeared no real warnings on what to do to maintain the glass; or rather what would damage or void a warranty. I simmered some maple syrup, and as it so often does when reaching the proper temperature, it boiled over. On a regular burner, one just uses a little elbow grease and your stove is returned its previous state. This actually pitted the glass, and as the warranty people at Maytag informed me voided the warranty, and seriously weakened the glass top suggesting it would be likely to break. Seriously?????? All of us boil stuff over on the stove top from time to time, and this damages the glass top and voids a warranty??? VERY DISAPPOINTED in Maytags product and their warranty.

Wow, I bought a Maytag Bravo 300 series washer and dryer three years ago. They have been a complete piece of crap. I spent nearly $2k on the set at Home Depot. During that time, they have been serviced four times and I am now out of warranty and the washer is constantly breaking with LD and F51 errors. The heavy dryer door with light as hell hinges fell off on my wifes foot when she was loading it. I cannot get it back on. It is rigged so it will work. I contacted Maytag and they were not helpful at all. Pretty much sorry about your luck. I will never buy another Maytag product again. I agree with other posters. Too bad you cant chose zero stars!

Just a year after purchase, this Maytag Bravos Washer stopped spinning the clothes. It never washed worth a damn anyway. I paid extra money for a quality product from a known brand name and I was taken to the cleaners. Never buy a Maytag product unless you want to replace it in a year.

Side by side refrigerator model #msd255oveu01. I bought this refrigerator Apr. 2011... The 1st year, the ice kept sticking in machine or freezing up. Now they have had to replace the modules 3 times. Once fall of 2012 and and again yesterday, 3/19/14 and they had to come back today to replace that one. I have called Maytag and they wont stand behind it since the warranty is over. I have told them that this is an ongoing thing with the ice maker and I have had to have it serviced ever since I have bought it. I told them from the git go that the ice maker needed replace. The ice dispenser also drops an ice cube on the floor on occasion and if I use crushed ice it jams up. This product is defective and is not a good product.

I have a Maytag Performa washing machine (model no. PAVT234AWW) and called the Maytag parts department to order a plastic pulley for the main drive motor. I was told I would have to purchase the 189 dollar motor just to get the plastic pulley. After two days web searching and calling local appliance stores I found that Whirlpool who uses the same drive motor sells the pulley (part no. 21001108) for 9 dollars. The Whirlpool pulley is even made out of stronger plastic. I just wonder how many Maytag customers have had to purchase a drive motor like I was told I had to by Maytag just to fix a 9 dollar pulley. I got lucky and my problem was solved, but only because a local store happened to have this particular problem so frequently that they were able to help me out when Maytag should be the ones helping out their customers better. Thank you for your time.

A lot of the reviews contain complaints about the Bravos XL MCT top load washer. We purchased one in December, 2015, and so far have not had any problems. We had a 3 yr old Whirlpool side loading washer that we just gave away, as it never got enough water to even dampen a comforter or quilt. This machine works very well, in spite of lower level of water. I was pleasantly surprised when I could see the water level with the first load! The controls are not as intuitive as other machines; e.g. spin only requires you to select Rinse/Spin cycle, and THEN turn OFF extra rinse. Perhaps the proper way is to have a Spin-Only cycle, and then tell the user to click the extra rinse ON. We do probably 1 load a day. Water bill has not been significantly higher than when we had the Whirlpool that hardly used any water. Today, though, a heavy quilt (it WAS distributed evenly around the impeller) was put on Bedding so the water level would be a bit higher to ensure the entire quilt was wet. Fine so far. However, during the Spin Cycle, the unbalance became so violent that the washer stopped for a few seconds and then went BACK to the Rinse cycle. It did this several times before we realized that the time remaining had not gone down in over 30 minutes. My guess was that the sensor believed that maybe some additional water with another Rinse cycle MIGHT even out the load. It didnt. I finally stopped the machine, redistributed the quilt and then ran the Rinse/Spin cycle, choosing NOT to do the extra rinse. All came out fine. There was NOTHING in the manual indicating that this might be needed, except for the instructions to Spin only. If I have any other problems, I will send here.

The washer is designed to use low amounts of water. The top is glass so you can watch what is or is not happening. The manual states there should be clothes above the water after filling. However after the wash cycle with a full or even half full washer, there is still some dry clothes above the water. As a result the clothes are not washed until the rinse cycle. I called Maytag and a repair tech came out to fix it. His solution was to trick the sensors by dumping a pail of water on top of the dry clothes before starting the washer. The sensors think there are more clothes than there really is. Will never buy another Maytag or Whirlpool product again.

I bought a Maytag washing machine September 2017. The lid is cracked. We were told by the repairman today that this is a common problem. The quote for a new lid was over $300. Of course we are not going to spend that much for just a lid. We will be buying a new washing machine and will not be buying a Maytag.

On Nov 1, 2018 - 14 months after purchasing this top of the line refrigerator - the compressor broke and the freezer stopped functioning. I called Maytag Service who said the soonest they could repair it was Nov 12 - 12 days after it broke. Also they said my 10 year warranty didnt apply unless I had proof of purchase. I said I registered my product online when I bought it but they said they had no record. So they had to charge me full cost of service and parts which would be $1000-$1500.I then called LOWES SERVICE ADVANTAGE - I really like Lowes by the way - and they verified my proof of purchase and that in addition to the appliance warranty I have a 5 YEAR mechanical parts repair warranty through LOWES. Thank goodness I purchased the service warranty from LOWES because Maytag was NOT honoring theirs! So then a repair person from FAST APPLIANCE REPAIR INC came to fix the refrigerator and said because it was the compressor he couldnt repair it so I had to wait a few days later for the COMPRESSOR SPECIALIST to come out. The compressor specialist came and said he didnt have any in stock so had to order one.Six days later - Nov 19 - the compressor arrived at my house. I called FAST APPLIANCE REPAIR and asked for someone to schedule an installation. I said Im RETIRED and can do it any time. They said the soonest they could install it is NOVEMBER 28 - ONE MONTH AFTER IT BROKE. So now Ive lost two large drawers of frozen food that spoiled. I have no refrigerator this week for my birthday and for Thanksgiving. I have to wait another 9 days to get it fixed. I am NOT HAPPY. I am sharing this experience so anyone considering buying this or any other MAYTAG product will think very carefully before making their purchase. Also, be sure to buy from Lowes and get the Lowes service plan for any appliance. Ill try to update this if and when my refrigerator gets repaired.

I purchased my Maytag Centennial Commercial Technology MVWC200XW in May 2012. This is the second time in almost 3 years that it breaks down. The basket decided to drop today and by the time I realized that it did, my whole bathroom had flooded, the water spread down the hall into my spare bedroom and soaked through the floor, also flooding my basement. I called customer service. They are sending a repair man next week, but as for all my ceramic tiles that are now cracked in my bathroom and my hardwood in the hall and bedroom that is full of water and are lifting off the ground. Its my responsibility to call my insurances to fix it. Yet it was their washing machine that caused the damage in the first place. When I purchased the washer I didnt expect to have to repair it every year. Not impressed! I do not recommend this washer.

I have had this washer (top loading washer model MVWX550XW0) almost 2 years. It has ruined some of my clothes. It does not properly wash anything. I have tried every possible solution. I cannot use the HE powder detergent - it will not rinse out. I tried using less than required and double rinse, absolutely did not overload. Even using the HE liquid still did not get clothes clean. I used the number one detergent to the cheaper brand - it makes no difference. I still have to double rinse everything. Small throw rugs will not even get totally wet or clean. I took clothes to the laundromat just to make sure it was the washer. It is this washer. I know I have waited too long to register my complaint, but I have basically thrown away $1200. Also, loads of clothes would take up to 1 & 1/2 to 2 hours to wash. Now that is definitely not energy efficient. I would love for you to pick it up and bring me a standard washer and dryer. I work for a research firm and know when companies really care about their customers. I will be interested to see if the Maytag Man really cares. The only reason I did not check angry is because of my delayed response.

I purchased the Maytag Bravos washer and dryer in September 2010, before moving to Washington. After a few months, the washer broke and had to have a repairman out twice to fix. It never would wash a blanket without stopping with error messages. He told these were notorious for problems. Now our dryer is leaking and not drying. I checked the vent hose and water and some wet lent are inside. In moving the dryer, I can hear a piece rattling around inside. From research and other posts, it sounds like its a broken pulley system inside. Maytag is junk. Customer service is terrible! I bought this unit during a veterans day sale at Lowes, using my veteran discount. Obviously, Maytag has no problem ripping off veterans or anyone else based on their horrible customer service. I will be actively posting as many negative online posts and videos about my experience on every forum and veteran site I can. They are horrible! Stay away from Maytag!

Water level is totally inaccurate, if you do get enough water in it, it will not spin clothes dry. This is the worst purchase I have bought in my entire life. This washing machine fails in every aspect period!! AND the matching dryer is a waste of space as well, clothes come out damp regardless of setting or time period. When I was younger, Maytag meant something, not anymore! I have searched to see if there are replacement sensors, or upgraded components to make these machines work properly, that I would even be willing to pay for myself and get them installed to make them functional, but NO they dont even offer that... we are just stuck with them. My water bill is higher and my electric bill is higher too! From these machines. I wouldnt even sell them used to another person. I wouldnt want them to inherit these problems, but as soon as I can save up enough money {being disabled} I will get these hauled off and buy a set of Speed Queen machines. My wife and I are so repeatedly disgusted!! I wish I had the receipt so I could post it for more proof.

We were offered a Maytag microwave with our newly built home two years ago. I do not know if it was a good value for the money compared to other brands as I did not price or feature shop for this oven. But the oven has worked well since we moved in.

This washer ( MHW3505FW) leaks, is crazy loud, water wont drain, clothes smell bad after washing, defective drain pump, defective mother board. Only had 2 1/2 months and it broke. Maytag refused to refund me and Lowes refused as well. Thankfully I paid by credit card. Am disputing the charge. Terrible washer should be recalled. Many complaints on this washer. Very disappointed and upset.

I bought a Maytag washer and dryer at Lowe's when I bought my home-the price was great and I have not been disappointed in them-have had them over 3 years now. My washer has a stainless steel tup and is a top loader. The combo of the two was less than $1,000. The washing machine has deep clean, heavy load or light load, hot, warm or cool water settings, a hand wash setting and many other features that I think most consumers can appreciate.

Nineteen-month-old dishwasher was repaired once while under warranty; 6 months later, same problem. They said they would send me a new part but I would pay for labor. I wasn’t happy but I agreed. I am being forced to use their people and pay first before the part is received and before the work is done. They said this is their procedure. If I must pay labor, I should be allowed to use whom I want. It is absurd asking for payment before job is done when the part is free. I have since checked the complaints, and there are over 200, with one woman on her fourth control panel – I will be on my second one. I feel this machine should be replaced free of charge. Its obviously a lemon!

Three-year-old top load Bravos. Started doing the LD/SD tango about one year ago. Intermittent fault, but becoming more prevalent. Can spend an entire day attempting to finish one load; sometimes must be unplugged overnight to clear faults. Washer receives heavy use from extended family of five adults and two children but has never been overloaded. Machine is horribly flimsy and constructed of the cheapest possible materials. I wish I had removed the back prior to purchase.Just because it is possible to attach a processor to a piece of equipment doesnt mean its necessarily a great idea. Any geek can tell you that the three things most despised by a digital device are heat, humidity, and vibration. A washing machine by definition is an epicenter, a breeding ground, for those specific environmental factors. Well done, Maytag. You have demolished what was, perhaps, the most respected name in the business. Good luck getting that particular rep back. Purchasing a Speed Queen. The living embodiment of old-school. Electro-mechanical timer. Stainless. Porcelain-enamel. American-made. Not one complained on this site. Might just shoot an Office Space vid centered on the demise of the Bravos. This time, its personal.

Top of the line $1300 Maytag Maxima MGD8100DW probably rusted much earlier before I noticed. After all how many times you check the drum of brand new top of the line dryer?? Manufacturer says not covered. Not sure but already this brand new model has been discontinued, so the manufacturer i.e. Maytag or Whirlpool take your pick found out about the defective design/part but now does not want to honor the warranty ridiculous. And one of the main selling points was made in USA (which turned out to be only assembled in USA), and the consumer reports which gave good rating but they were duped too.

Our Maytag French Door with freezer on Bottom MFF2258VEB quit on us after three and a half years. Called local authorized Maytag dealer. They sent out a repair man. He said the main control board was bad! After much discussion we told him to replace it. After part and labor $261.00 it is running for now. Then called Maytag to see if they could reimburse us for the part $161.00. NO DICE! I have a kitchen full of Maytag products and a washer-dryer set but will not BUY ANY MORE Maytag products. Pass the word to boycott all MAYTAG PRODUCTS!

The dishes need to be washed off to be sure they will be clean. It holds a lot of dishes. You can put it on a short wash or long one. Leaves water on base of glasses sometimes. Holds moisture. Heavy wash, normal wash, light wash, rinse only, auto clean, delay 1-9, heated dry, sanitize, tough scrub, extra rinse. Regular size 24. Beige color. Electronic buttons. Maytag Quiet Series 200: I do not like the racks for putting dishes in. Otherwise it holds a lot. It does not clean dishes if you do not rinse them off first. If you run the dishwasher immediately after putting dishes in it will clean them off. Sometimes it leaves water standing. Even with what I have said I really like this dishwasher. We have had the dishwasher a long time. We use it at least 2 times a week.

HORRIBLE. Dont pay more for substandard machines. Had a Maytag washer and dryer delivered on March 27th 2018 and it has been a nightmare to get it to start up. Now I have clothes stuck in there. I called Home Depot, you should never buy any appliances from them, they wash their hands of all responsibility once you sign for it. Called Maytag. On hold for almost 10 minutes, they only have 2 certified repairmen in the area 0f 600,000 people. Will be 5 days until they come to look at it. I told them I wanted to return it for a GE or something else. They said I had to contact Home Depot yet Home Depot told me it was Maytags problem. SAVE YOUR MONEY!!! MAYTAG IS NOW AN INFERIOR PRODUCT WITH EXTREMELY INFERIOR SERVICE.

Bought new in 2006. From the beginning it shook a little. I could not use high speed without leaning against it and pulling upward on the unit. Maytag service workers came out and at first said they needed to balance it. That was not it. Then they said it was the drawers that I purchased as an option. Finally, one guy just straight up said they had no answer for it. Then came the day, last month, it was spinning and suddenly it started to rock and I ducked out because I thought the tub was coming through. I seen smoke. Yelled for the kids to get outside. With the phone in one hand calling the fire dept, I ran for the electric box & started throwing switches. Fire dept said that is what saved my house. Now it sits in my dining area because of a lawsuit I was never contacted about. No parts are available. Thats what happened when Maytag chose to send the business to China. Now they are back to making them in the USA but why would I buy again from a company that does not make good? Well I love blogging and Facebooking. I know 40% of Central FL because Ive lived here 60 years, plus my husband serve all of Orange County 35 years. This review will go out all over. Anyone need a tall table?

Purchased Maytag dishwasher July 2013, installed August 2013. Stopped working Oct 2, 2014. Called Maytag and they offered to let me buy a service pan for around $300. No thanks, stupid Im not. I also sent an email. Have not heard back but Im sure Im still out of luck. According to the California class action suit regarding the Maytag control panels, Maytag is saying there are no problems with them. Wish we all had some power to make them see otherwise. Will I ever buy a Maytag product again. No. They would be much better off keeping their customers happy rather than spending tons of money on ads trying to get new customers. Since Maytag is owned by Whirlpool, they will not get my money either.

We bought top load washer model # MVWC425BW1 at Lowes brand new 9/22/14 for $493.93. On 11/23/2017 it stopped working and would not even come on after lid locked. Found out it needed new parts that would cost us over $300 to fix and we could buy another new washer for $400. We are very disappointed that this washer with only two people only worked three years when we thought we had bought a reliable product that would last. Sent several messages in November but no response till today 12/13/17 after filing. BBB complaint filed and they decline to do anything. So this company just wants to sell products but has no customer service. They only give a year warranty. Of course if the product is not going to last they want you to buy more.

I write this as the repairman is fixing my Neptune washer. As with many other complaints, I was experiencing the awful mold smell with the only fix being leaving the washer door open when not in use. This works but for the past few years a switch on the front broke which means we have had to leave the top off the washer and rig it every time we used it. Sometimes it would work and sometimes an error code would show and I would have to just turn to spin and finish that way. At the same time in 2005, I purchased all Maytag appliances. First the microwave went out then the ice maker broke and is still broken, then the dishwasher went out and had to be replaced. Washer broke so basically the only thing that has had no issues is the oven and all happened just outside the five-year warranty. Never again will I buy Maytag.

I have a 2-year-and-5-day-old frontloader washing machine. The bearing and axle broke. The repair is over $500.00. It appears to be a known problem, as Maytag knew exactly what was wrong from the description of the noise it makes. They knew all the parts that would be needed. They would send the parts but not help with the labor. Evidently, it is a two-person job requiring several hours. They are not consumer-friendly and do not seem to care that the company reputation is going bad fast.

We bought our Maytag dishwasher less than 2 years ago (model MDB8969SDM0) and we are remodeling our kitchen now January 2018, and when we pulled the dishwasher out we found that the wire (12/2) had melted into the back panel. We won’t be putting this Maytag back in.

Maytag calls peeling paint a cosmetic issue. With a convection oven it could be a toxicity issue. Waiting for an answer to my question as the fan blows the peeling paint onto anything that is not covered. Dont put foil on the bottom as this compromises the paint due to design. Truly sorry to have purchased Maytag as this line is not the Maytag we grew up with! Old school ovens and products had the quality or workmanship to last.

Does a good job of cleaning but takes much longer to complete. Pretty much standard features. Has rinse only cycle, air dry only cycle, and cycle for pots and pans. Top rack had special holders for long stemmed glasses which I dont need. Standard size. Same size as my Kitchen Aid. White, front load, no special appearance. It takes much longer than my old dishwasher. Also the soap dispenser broke after 2 months and had to be replaced. It requires that two buttons have to be pushed to start. My old one only required one. It does a good job of cleaning.

We bought this washer in February of 2010. We had the pump replaced under warranty in January of 2011, and the pump appeared to have a hole in it from some type of hard object that had gotten inside the pump and damaged it. We then replaced the L-shaped hose between the tank and the pump because it had a small hole in it - very thin rubber. Last week, the washer was leaking again and the service technician said that the pump housing was cracked due to a penny rattling around inside the pump.This washer performs very well when it is working but it seems to be too fragile to handle on normal usage. The Whirlpool washer we replaced with this one ran for 23 years with no problems before it finally went out. From all appearances, it seems that every failure we have had with this washer has been due to damage from foreign objects getting trapped in the pump. Is there no screening mechanism to prevent hard objects from entering the pump? This seems to be a design flaw more than anything.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

I have a Maytag refrigerator that is about 6 years old. I like the fridge, but the icemaker no longer works and water constantly drips from the door. They will not fix it, even though we have an extended warranty that they have provided. I have waited for months and I am told an icemaker is not important and the fridge is still working, so why am I complaining? When you pay for a fridge with an icemaker and water dispenser, I believe it is part of the refrigerator I paid for and it should be fixed, but Maytag doesnt seem to think so.

I have a front loader dryer, model number MAH5500BWW, serial number A9147862ec. All of a sudden, I found water on the floor and after opening up the front door, I see where around the part that sticks of on the inside of the door, there is a big piece of plastic that has broken off and cracked all the way across the bottom of the door and is missing. It is allowing the water to leak down the front of the bottom of the washer and onto the floor.

First failed after 16 months. Second twice in 15 months. They are lucky to last 16-24 months. Stupid for a microwave that normally last 5 plus years for every other brand I ever bought.

To begin with, the Bravos 300 washer was bought because we owned a Maytag previously and it was with us for 25 years. It was still running when we gave it away and the only problem was a small oil leak starting at the drive. The new washer has no agitator, just the new style flat thing at the bottom of the tub. You cannot wash a set of fitted sheets without it turning into a tangled mess. The washer quit working after about 5 years and all indications pointed to the control. The control would reset after unplugging, but would freeze immediately when you tried to enter a command. We live in an isolated place and it is not feasible to fly in a service person. I ordered a new control, but there was no change in function. After several hours of detective work, it turns out that the mickey mouse plug for the electrical connection at the pump had broken inside. Because the pump would not work, the whole control would freeze. We will never buy another Maytag.

I purchased a Maytag dryer (MDE2400AZW) 2 years ago, but have only been using it for the last year - and fairly infrequently, as this is a dryer that my guests use. I called Home Depot where I bought the dryer (along with the washer). I thought I had purchased an extra warranty, but turns out I only had it on the washer - what was I thinking. I wish I had read these reviews before I made my purchase. My local repair man charged me $192.00 for a new heater and his time. Theres a whole 90-day warranty on the new heater!! I sure hope this one lasts more than a year otherwise Ill be buying a new dryer and it wont be Maytag.

I purchased this washer on 5-25-15. It was delivered on 6-2-15. It worked for 11 days. On the 13th, I called Maytag and made an appointment for it to be fixed. They said a technician would be out on the 16th to fix it. I got a call on the 15th saying the part they needed was not released yet so they would be out on the 23rd. The guy comes on the 23rd and diagnoses the problem. He says the machine has a bad motor and shock of all shocks. He doesnt have the part to repair it. They originally assumed it was something else and were wrong. Fantastic. He said he would be back on the 30th. I got a call on the 29th saying that, once again, the part needed to fix it was not released and that they would call me to make another appointment when it was available. I had enough. I originally purchased with Home Depot and called my original salesman. He told me he would replace the washer with any brand I wanted (I paid the difference in cost of course) but I was still relieved that he was willing to work with me. I ended up going with an LG. Lets hope that one works. I have 2 kids and have been having to go to the laundromat. I have to say that I loved the machine for the 11 days it worked! I would probably still have it if they had better customer service but Im not going to continue to put up with them not having whats needed to fix this thing.

Bought the xl about 14 months ago. NO LIE! Exactly 2 days after the 1-year warranty was up, the xl went down. Drive shaft and bearings. Did Maytag honor the warranty since it was only 48 hours past the expiration? Not just a no but a why are you bothering attitude. My brother and I are above average machine builders. Well fix it ourselves because we could buy a new one to have it repaired. After many hours scouring the web we found the parts. Maytag didnt make a repair kit available to the public. 7 hours plus over $200 to tear it down and to clean the muck trapped at the drain. Then sand-smooth the burnt on metal where the bearings sit. All for a washing machine that sucks at washing clothes in the first place. Never ever again will I buy a Maytag.

We purchased a new Maytag Bravos Washer and Dryer in April 2012. The dryer has been nothing but a piece of trash. It has been serviced 4 times for the same problem. The first time, a thermo element failed and dryer wouldnt heat. Second time, thermo element failed and was replaced. Third time, thermo element was replaced and flame scoop was replaced. Service man called the factory to find out what could be causing this problem. Factory service recommended replacing gas valve. The valve was ordered and replaced. A couple weeks later, the thermo element has failed again, and of course, the failure happens on a weekend. We are a retired couple, so we might only have a couple loads of clothes per week. All of the repairs have been covered under the first year warranty. When you spend $900 for a dryer, you would think it will work for at least the first year!

Purchased an over the cooktop microwave 3 years ago, it came with a 20 year warranty. It stopped working and I promptly emailed Maytag customer service. It took them over 3 weeks before they responded. That is not acceptable. Did they think I had a back-up microwave to take its place until they finally got around to reply to me? Well we could not wait, and we just threw that piece of junk out and had it replaced with a competitors unit. We will never buy Maytag again and will inform anyone we know about the poor operation of Maytag products and lousy customer service. My suggestion to anyone considering Maytag products is to not waste your time and money and look to another manufacturer.

Maytag Bravos Quiet Series 300 - Our motherboard on the washer went out after 2 years from purchase - just out of warranty. Motherboard was $550 so we bought a Samsung. Now our dryer has gone out for the second time. First time was the pulley assembly came apart. We self-repaired after watching YouTube. Now the motherboard has gone out on the dryer! I will NEVER buy another Maytag product. They are a waste of hard-earned money and have left me with piles of laundry numerous times. Maytag, you need a class action suit filed against you!

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

My original GE dishwasher that came with our house finally crapped out after about 8 years of use in 2007. Bought a Maytag from Home Depot for around $400. Dont remember the model number. It worked okay but then in the middle of 2010 we got a letter in the mail saying our machine was being recalled because the heating element might catch fire (!!!). The recall gave us the option of getting it fixed or getting a $150 rebate. We chose the rebate option so we trashed this dishwasher and went back to Home Depot to buy another one.We found a very nice Maytag with the stainless steel tub and the racks with the lifetime warranty against corrosion (which was good because our previous Maytag had started to leave rust on our dishes because the plastic on the tips of the rack tines was starting to come off), model #MDBA979AWB1, serial #FY2501885. The one we found was a no-box display model but it had all the accessories with it and still had the factory warranty. We got it for just over $300 and with our rebate applied we were out the door for under $200 including tax. I installed it myself and didnt have any issues for quite some time. My wife and I were both very happy with how clean the dishes got!Now, last night the dishwasher wouldnt start. I checked it out this morning, made sure it had power and was able to get some lights on the control panel to light up but still couldnt get it to start. Looks like Ive been victimized by the control board as most of these complaints have said. I guess I should consider us lucky since ours seems to have lasted longer than the average 18 months to 2 years. Will be contacting Maytag and Home Depot to see what they can do but after reading all these negative reviews Im not hopeful.

How can any company with a reputation that we all have grown up with MAYTAG pull such a DESPICABLE act on its customers of 20, 30, 40 plus years ??? $500+ repairs for each of 2 boards in nothing better than a BOAT ANCHOR... I would give anything to have my 15 yr or even 20+ yr old pair back! Worst purchase of our 50 years of life! Its overdue time for a Class Action Lawsuit! Also has no one had your washer jump and dent your dryer? Imagine a child in a room with something as Vicious as MAYTAG BRAVOS! Just as well have them play in the STREET! Lets all join together and show MAYTAG the consumer does count. Thank you...

Maytag Centennial - It came with the house. I think its a line made special for rent-to-own kind of places. I cannot stand the washer. It will not take fabric softener unless its in the ball and if you use extra rinse you dont get to use fab softener at all. (I like liquid fab softener on some things). Why it doesnt have a dispenser is beyond me. And the bleach dispenser is poorly designed, too close to the tub and splashes every time. Ive had this six months and would get rid of it in a heartbeat if I could afford to. Plus it snags towels. The washer is crap. And its a Maytag. I wish it would break so I could justify buying one that has some decent features like fab soft dispenser, bleach dispenser that doesnt splash, drum that doesnt snag.

We have had our Maytag dishwasher MDB9100AWQ only 5 years and now it keeps shutting off. I see there is plenty of this complaint. I will not purchase another Maytag product after reading all these reviews and experiencing it.

Purchased a pair washer/dryer Maytag Bravo XL module from Home Depot, Brentwood, CA #1076 branch. The first day I received my machines, the dryer had a defect. I called them within 24 hours to report the issue and requesting a return. Home Depot wont take it back; they said I have to go though the factory warranty to fix any problems. Its like buying a car, once you drive it off the lot its yours they said. 3 weeks after the washer started making noise. Home Depot kept delaying my claim for more than six month so I couldnt dispute the charges with the credit card company and avoid the California lemon law. I consider this a loss of money and time. Worst appliance purchase experience ever.

Model mdb7749sbm. Unit is just over 1 year old and fails in the same way everybody else in complaining about. Here is my question, this failure mode is obviously a designed in feature providing planned obsolescence to the device. Why is this company not being held to account for the damages in this case? Are all the judges that bought that no suit can be brought?Have all of you contacted your state consumer protection organizations regarding this issue? I would also recommend that you write both your state senator, the state consumer protection organization and any media outlets you can think of. High rate of control panel failure, devices activating by themselves when people are potentially away from the house, risk of fire or flooding... these are serious things and I would think a story that some news organization would surely be interested in digging into. Now that would serve to light a little fire under the Maytag organization if something like that was to occur.This sure seems to me to be a defrauding of the consumer - selling them a product at the top end of the price range that has such a significant design flaw that in the end can only be considered not fit for purpose. I havent yet contacted Maytag and Home Depot (who I believe are fully complicit in this as well), but I will be doing so to give them a chance to make this right, which I fully expect them to decline to do. Then I will begin writing letters. Am also considering small claims court. But above all, do not just accept this and move on! Companies like this need to be held to account, and they need to be reported so that others purchasing new devices in the future know to stay away from them.

I bought a full kitchen of Maytag appliances when I bought a new house in 2009. I thought it was a reliable company. Id always gone with GE before. I couldnt get the packing sticker off the oven after trying everything to remove it, so the oven bottom is virtually ruined. The timer on the oven dings once and stops; dinner burns if Im not right there to hear it. I was told by customer service thats the way it works, so I had to buy a separate timer. I am now replacing my 2 ½-year-old dishwasher because the control panel has once again stopped working. It cost me $275 to fix the first time and it lasted less than 3 months. I will never buy Maytag again! I got over 20 years of service from my GE appliances.

Bought new glass top Maytag electric range. Only used oven 7 or 8 times when I was unable to close the door. Had to wait 12 days for Maytag repairman. Has to order new parts. Still without use of oven. Says its a known problem the hinges holding the door arent strong enough. Last stove 24 years old. Never had a problem.

My Neptune dryer purchased in November 2005 had the drum crack at about three years old. I complained so much that they finally agreed to send a replacement drum for free. Now, two years later, the drum has cracked again and tore through the housing on the front of the dryer. The repairman said it would be too expensive to repair. Consumers, beware.

I purchased our Maytag dishwasher last November. Last week, the control panel went out. I called customer service and they were actually polite and helpful, except for the fact that I had to wait an entire week to have a technician come to my house. Being that I live in the Balt/DC Metro area, I would have thought they would have enough people in the area to come over faster. Anyhow, we finally had the technician come today and tell us that the control panel needs replaced and that he highly recommends an extended warranty, which costs $200 for 5 years. He let my husband know that the repair itself would cost $500 if not covered by warranty!!! What a ripoff! I purchased this dishwasher because I grew up believing in the Maytag brand. Sounds like this is an extremely common issue and if Maytag wants to make things right, they should discontinue sale of their crap product and provide those of us who are stuck with it, a complimentary 5 year warranty. I shouldnt have to pay $200 in extended warranty to make up for the fact that my control panel is likely to go out again in another year, when Ill be forced to buy a new dishwasher.

This machine (Top-Loading High Efficiency MVWB755DWO) does not clean, it only leaves soap and moldy residue on clothes. The Whirlpool company refuses to assist even though it was delivered less than a year ago. So much for warranties! Wrinkles clothes, wrings incorrectly and does not give you freedom to manage independent of technological controls.

Received new washer & dryer on Oct 2nd, 2015. The dryer has been acceptable, but the washer has been one problem after another. First of all the washer is so noisy beyond belief. The engineering is one dreadful design. At first attempted use, washer would not begin cycle. Sensor would say lock, unlock, lock, unlock for so long, I would cancel & begin again. It became such an annoyance that I placed start of cycle on a timer (it sat at sensor mode for 20 min.) then I restarted next time sat for 15 minutes without starting. After beginning from start position it would start OR NOT. First repairmen told me timer might be off a bit. As days passed with same issue, second repairmen arrived and found that door was off (not completely closing). Repairmen would place an order for new seal. Upon repairmen arriving for third time (new seal did not solve issue) he believes that lid is uneven, & he will order a new lid & return in a few days to repair. I must admit that service has been quick, but the issue is still a headache. I would NEVER recommend this model to anyone and would like for Maytag to replace washer with a different model. The noise is a factor that no one should have to endure. The grinding noise can be heard from three rooms away from laundry area with laundry room door closed! Im absolutely a very very unhappy customer.