MDB7749SBW - Purchased a new dishwasher from Home Depot & had them install it. It worked for 6 1/2 months & the control panel blinked & went dead. I did some research & found there were a lot of problems with the control panels & even a class action lawsuit. I went to Home Depot & they said contact Maytag & brushed me off. I set up a repair per warranty & all was fine for 10 months & same problem has happened again. I told them at Home Depot to replace the unit since nearly every repair job on the control panels prematurely fail again every time. I am going back to the Home Depot again. I do have older Maytag appliances that perform as required & I do know Lowes would have replaced the defective dishwasher.

Purchased Maytag Centennial Washer and Dryer (MODEL MVC300VWI) at Home Depot 3 yrs ago. After 6 months, washer started to rust. Maytag told us It was not their problem. A 6-month old washer should not rust! Poor quality + poor customer service. Dont buy!

I built a new house in 2006. As part of a builders package, we had all new stainless steel Maytag appliances installed. The side by side refrigerator compressor stopped after 26 months (of course, passed any warranty). No customer support through Maytag and as previously posted very scripted responses. Maytag microwave handle has broken off several times, the glass seal in the oven door was compromised and the inside glass is stained - most recently the on-going issue with my Maytag dishwasher model mdb5601. Ive already replaced the handle /door latch assembly twice and am confronted with the current dilemma if I should replace the control panel that now appears not to be working. It goes without saying that I will never purchase Maytag products again. However, I am not in a position to replace what are fairly new products. That being said, I am reluctant to purchase costly replacement parts given their poor performance and ratings as mentioned in this thread.

I have a Maytag dishwasher MDBH980AWQ10, within the 1st month of owning it there were issues. Now the electronic control panel is shot, dishwasher wont turn on. To replace it...almost the cost of what I paid, warranty has run out. In the last 7 years we have had problems with 5 various Maytag products, replaced our Maytag dishwasher which lasted 20 yrs and Maytag washer & dryer that lasted 30+ years and ran without a hitch. Maytag has not been helpful at all and their authorized service repair. A&E Repair Service is a bigger scam than they are. It is a waste of my finances and time to buy major appliances every 5 years. Each and every one of their new appliances has died shortly after all the warranties have run out. Im beyond frustrated, disgusted, and financially drained. It does not pay to be brand loyal to Maytag for they are no longer respectful nor appreciative of their customers. I would love to give corporate the opportunity to enjoy the same products that are in my home...in their homes...as well as the experience of their customer service. Last Maytag purchase for me! Is there anything that I can do in the meantime so Im not stuck with their lemons?

I bought a Maytag Bravo washer 11 months ago, and I have had nothing but trouble with it. I have had it worked on twice, and now, Sears is sending me a new one, because it is broken again. I would rather have my money back, go somewhere else, and get a new washer. I will never buy anything from Sears again. They could not send a person out for other repairs for 1 week. Then they would have to send out for parts, because the drum is peeling on the tops. So that means more time to wait for parts to come in, and the machine is not spinning out. The cycles are not washing right; sometimes, they wash a cycle 2 times.Sears does nothing but give you a runaround. And the Morrisville Vt. store manager is so rude. He was talking to me like I was stupid. Now, I have to wait 3 more days before a washer comes in from the warehouse after Sears told me it was coming on 4/24 between 9:45-11:45. Then the manager told me I could take the floor model if I want it today, which has scratches on it. I was hoping someday to buy the dryer to match the washer. But now, I do not want anything to do with the brand. I bought a Maytag refrigerator also last year. Its beautiful. Everything is in my kitchen, and I have been working on getting everything to match. I am raising my 2 grandchildren and am on a fixed income. They treat people awfully at Sears, and it is too bad Maytag works with them.

What a disappointment. I guess this is why we no longer see that commercial about the Maytag repairman being bored. Because now, he is out fixing these pieces of shirt. Im trying to fix my washer (Model: MAH8700AWW), what a sweet pain in the **. Dont do it. Throw it away if it starts making noise like an aircraft landing.

The control panel and the electronic control box had to be replaced after only two years of use. It cost almost as much as a new dishwasher (492 dollars). The model of the Maytag dishwasher is MDB77479SBM3. This dishwasher looks good from the outside and runs quite but the electronics are cheap and cant stand heat without melting. My wife and I are retired and only used this washer about twice per week. It looks good, cost 650 bucks and it is a pile of junk. No more Maytag in our house. We had this machine installed in July of 2014... It crapped out in July of 2016.

Maytag 6.2 Induction Freestanding Range Model MIR8890AS0 F47 - I am a very careful shopper. I spent many, many hours researching and searching for the best value. It took me over 2 weeks of research to find an induction oven we could afford. We are a family of 3. Normally, we use just one burner for dinner. We bought the range in Feb 2013. On August 5. 2014, we had company over for dinner. I used more than 2 burners and the oven at the same time and the right 2 burners quit working; I now have the dreaded F47 code. I have had numerous Maytag Authorized repairmen out. They ordered every part except for the one that was necessary to fix my stove. I purchased in Feb 2013, burners went out 8/5/14. This is only 18 months old and is JUNK. Arent our landfills full enough?Maytag customer service is awful. I spent hours on the phone, mainly on hold, in efforts to get help. Maytag claims to have such a great 10 year limited warranty but they wont warranty this F47 issue. Thank God I bought insurance with an outside company. The wrong parts that were ordered were at least covered by my own insurance policy; no thanks to Maytag. I am angry that I have to search all over again to try and find the right stove. I am now fearful of induction. I invested in a lot of induction cookware which was an added expense and burden! They need to stand behind their appliances!People cannot afford to waste thousands of dollars every 1.5 years to cook their meals! This has been an extremely unpleasant issue. It has cost me many hours of waiting for repairmen, waiting on hold, getting and storing many wrong parts ordered by repairmen. I calculate this cost me over 50 hours of my life on the F47 problem. Not to mention the time it took me to shop for this junk to begin with!I think they need to recall this issue as it is clearly a design flaw. I researched this and found many other owners had similar problems. The F47 means that the user interface isnt communicating with the range (the circuit board). They placed the circuit board under the burner surface area, sandwiched between the burners and the oven. It was just a matter of too much heat before this board shorted out. The cost to replace this board is over $600. I am afraid of investing another dime into this machine. I wasted time, energy and A LOT of money on this inferior product.

We bought a Maytag range Nov 2013. My daughter has maytag appliance and stand by maytag. We grew up with maytag. But those days are no longer. It is not about quality, it is about how many did we make, how many did we sell. I am very disappointed with my range. I tried several times to use my upper oven, in disbelief my lower oven was heating. This happened so much that I touch to make sure that the Correct oven is on. I also have problems with my knobs for my burners. I could not turn off burner after finished cooking. We had to unplug range and turn off gas, if we did not do that the burner would have remain burning. This very uncomfortable for us.I still believe in maytag. I am sure we have not talk to the right person. There is too much at stake for the company, too many complaints are bad for any business. I too am a victim, very disappointed, I wont give up. I have a warranty with home depot and they have been great. It is not their product but they sold it. I hope everyone with a lemon will get problems solved. We only want what we pay for, even manufacturer when they buy other products they want quality as well, we all do. Hoping everyone will be able to get justice. Thank you.

We had the same problem that everyone is complaining about re: frozen water in bottom of freezer dripping out onto floor. Swore when I got rid of the Maytag smooth top stove that broke after 5 years that I would never get another Maytag but broke down and bought this fridge. Maytag rep made it clear that the Fridge had a NOTE on file about the drain, but it was NOT a product recall. So after virtually taking the freezer apart before the repairman came, we ended up paying $120.00 for the repair, not the part. Yippee. Please note that the repairman told us we saved a lot of money by taking apart the freezer so most repairs probably cost a lot more than ours.

We have had this washing machine almost 1 year and the small problems have grown enormous. In addition to the constant soap residue left on the dark clothes (my guess is its on the light clothes too, but you just cant see it) the washer goes out of balance frequently (they are replacing the suspension, after they said its all working great). The repair man said Im not loading the clothes properly, I need to roll each item of clothing into a ball and then place it in the washer. Are you kidding me, my new machine has special needs? And dont put in too large of loads. What!!! Its an XL capacity but I cant do an extra large load, because half the clothes wont get wet or clean. Maytag blew it big time with these models, I could talk about the dryer too. Maybe next time.

Bought refrigerator 2012 from Home Depot (model something like MBF1953YEB - how sad is it that I now have this number memorized?). Freezer too cold, refrigerator way too warm. Freezer air ducts frozen over. Tried manual defrosting twice per YouTube suggestions. Finally got repair for $400!!! Thats about half what I paid for it! One proponent repairman stopped me mid-sentence when I said Maytag saying, I know what it is. The computer (Jazz?) board needed to be replaced for $217. I just looked up Maytag to see it was bought in 2006 by Whirlpool. So I wont be purchasing any more Maytag or Whirlpool appliances.

Worst washing machine I have ever owned. Read all the other reviews and concur with them. We get pin sized holes all the time. Brand new shirts yesterday and they have black stains all over them - not the first time either. Inside of stainless steel tub looks clean. Where do the black marks come from? Last Maytag I will ever buy!!

My dishwasher is 3-4 years old and the control panel is malfunctioning. Cant push a button to choose what cycle I want, it doesnt respond. I went to the Maytag website to see if there have been others with this problem. It appears that there are many other people having this problem. Parts are not available and it seems that Maytag wont do a recall on this product due to the control panel malfunctioning. I have been dealing with this problem for the past few months. I dont think Maytag is worth the money. They want if you only get a few years out of them.

In 2003, I purchased a brand new Maytag washer and dryer set, I chose Maytag because of their reputation. Within the first 6 months, I had a bearing go bad on it and that had to be fixed. It has become noisier and noisier throughout the years and now it is leaking all over the floor when I do a load. I am single, I live alone, I do laundry very seldom and do not do large loads. I am so disappointed with Maytag. When the repairman came out initially to fix it, he said that the brand he fixes most often is Maytag. Expensive lesson learned, Ill never buy any type of Maytag product again.

Maytag is a reputable brand name for a washer & dryer. However, they have done very well in the oven/range industry as well! I own a oven/range for over 4 years now and it works great???! Food is cooked to perfection and cleaning???? And self-cleaning is a snap!

I purchased Maytag Bravos XL Steam Washer brand new from Lowe’s in January 2018. HORRIBLE washer! Does not get clothes clean and leaves soap and scum all over clothes. I have to wash everything on power wash with an additional rinse cycle (takes about 2 hours per load) and clothes still don’t come out clean. I often have to wash a load 2 or 3 times to get it clean. Will NEVER PURCHASE another Maytag product! What is even worse is that I also bought the Maytag “commercial technology” washer at the same time. It’s an even more TERRIBLE washer. Cannot get through one cycle without getting an LF (low flow) error & the cycle shuts off and machine drains & quits. Absolutely the two WORST washers I’ve ever owned in the past 40 years!!!

I purchased a Maytag electric slide in stove, in stainless steel. The aqua clean is a joke, ran it for three cycles after cooking one roast and it does not work. Then to add insult to injury I had to get on my knees using a turkey baster to remove what was left of the two cups of water. The finish on the front is coming off. Not at all what I expected from a 1500.00 range. Poor quality. Now there is the sound of a fan running and I am not using convection.

I purchased a Top Loading Maytag January 2019 (High Efficiency Washer) and I have had problems with it every time I do laundry. It doesnt matter what cycle I have it on. It doesnt fill properly when I put it on deep full. It tangles my clothes so I have to untwist them when I take them out. It has torn some of my things due to twisting. Some areas of the clothes dont even get wet. Some areas also do not get rinsed properly and I have to repeat the cycle. I have had repair people come out and they cant find anything wrong. I am so unhappy with the washing machine and Maytag just ignores the issues I am having. Im going to have to give it away and get some other brand. I am just devastated that I spent all of this money and clothes are getting ruined.

Maytag Dishwasher model #MDB7759SAW3 continues the Whirlpool company legacy of subpar control panels in all of their dishwashers. It is telling that they have been allowed to market the exact same failing parts for well over a decade without any accountability. They had one recall circa 2007-2010 and pushed customers into purchasing the model I have which suffers from the exact same control panel design.To further frustrate the consumer experience, Maytag customer service reps and supervisors allege that they have never heard of a customer having issues with their dishwasher control panel before. The panel beeps endlessly and refuses user input regardless of whether the door is opened or closed. After a power disconnect it will reset and sometimes allow one load to be washed before resuming the non stop beeping. If opened and closed during the beeping it will cycle through a completely new wash cycle on its own and resume beeping. Maytag customer service response this morning was, “thank you for being a Maytag customer”.We will my be purchasing their replacement control panels as they are of poor quality and it is well documented that the new ones fail annually as well. These are “high end” appliances and are not inexpensive. We will simply cease to use whirlpool, Maytag, Kenmore, Kitchenaid, etc. brands in our home and will advise everyone we know to protect themselves the same way.

Weve only had the machines for about a year, but so far they operate perfectly. However, the washing machine seems to take much longer to operate than my prior machine and is much noisier. But, the cleanliness of our clothes is great!

Not only does dryer come with missing parts and are told by Maytag 1 to 2 weeks for delivery or drive 25 miles to pick up one. You do not qualify for rebate even though you do not receive washer and dryer for 5 days after rebate starts. Should have kept my old GE was faster and got clothes cleaner. Was looking at a Maytag refrigerator not anymore with their service.

Seems a little ** one of a small child crawled into the washer and a sibling turned it on. We have been married 35 years and seen a lot of washers and this is by far the worst wash machine Ive ever seen. How would you rather do my wash in an old fashioned mangler? Very unsatisfied customer.

I am PISSED off at Maytag products in general. First I buy a washer and dryer from a Maytag store-buy a 12 year warranty. Call in for repairs - Maytag and A & E say I have no coverage. Now I am getting bills to pay for coverage on both because the form says my coverage ends this December 2011. I buy a Maytag dishwasher and its the one that catches fire. I get the rebate of 250 for buying the more expensive one - but am still out 500 dollars. Installation was bad by contractors from Lowes - just called that in to have it reinstalled. AND THE MOST RECENT IS THE FRENCH DOOR REFRIGERATOR I BOUGHT 9/4/2010. IT STARTED ACTING UP AROUND CHRISTMAS TIME - WEIRD NOISES, WOULDNT MAKE ICE - I AM SO BUSY WITH MY MOM I DONT CALL IT IN UNTIL JUN 25TH AND THE REPAIR PERSON SAYS IT IS UNREPAIRABLE AND HAS INTERNAL DAMAGE TO THE WIRES.

We purchased a Maytag Bravo washing machine and dryer from Home Depot so needless to say, it was not an inexpensive purchase. I absolutely will NEVER purchase another Maytag ANYTHING! The washer will not spin and when it does, it sounds like it is coming through the washroom doors. The heating element has had to be replaced in the dryer and has always had a sour smell inside. I have nothing nice to say about these products and would absolutely NOT recommend them to even my worst enemy!

No matter what we we do we still have soap residue left on clothes, even when we do the 2nd rinse cycle (what a waste of water). We use the correct amount of HE detergent and we use the detergent dispenser but it doesnt helps. The machine just doesnt use enough water. We have removed items that still have DRY SPOTS on them when the cycle is done. Areas that have never gotten wet after a 45 minute cycle. Never once had this happen with an agitator machine. Would not buy this machine again. Model: C80441070. Serial #: MVWX655DW1.

Two years ago I purchased a Maytag Top-Loading HE Low-Water washer. I have always taken great pride in the way my laundry looks and smells but since this purchase, my laundry no longer smells clean and fresh nor does it look clean. I have always used the same detergent and fabric softener (only now I use the HE version) and it served me well. I have read all of the directions and did as I was instructed. I cannot believe that anyone would actually think that you can do laundry with practically no water. Do the decision makers have not common sense at all? I didnt and still dont believe it but what choice did I have when all of the machines are now HE with low water. I think its terrible that consumers dont have a choice. I have come to realize that low water, HE washing machines actually waste more time, energy and money (detergent and fabric softener).My clothes are not clean, nor do they smell good when the wash cycle is finished so I have to wash them again, using more detergent, fabric softener and energy. The super fast spin that supposedly sucks out most of the moisture, also rumples my laundry with semi-permanent wrinkles (even on the low wrinkle setting) so clothes that never had to be ironed before, now need pressing. I find it remarkable that, with all of the detergent ads promoting washing clothes in cold water to save energy, we are told that if our clothes are not sufficiently clean in cold water in our HE washers, that we should try a warmer/hot temperature. Good luck with that because my machine has several temperature settings but only uses one - COLD! I cannot actually believe that with all of the technology that our society holds, we are going backwards in the basics of washing clothes. Terrible product, terrible quality, terrible results, terrible waste of time, resources and money. Why cant you just leave some things alone??

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

I thought I was safe in buying Maytag for all of my appliances in my new kitchen. I bought a double wall oven Maytag MEW6630DDS. I bought it in late 2010 and have had no issues until August of 2018. I rarely use the bottom but used it in August of this year to cook cupcakes. After baking them and leaving the kitchen for a short while I heard a loud explosive, shattering sound. I walked to the kitchen to see that the bottom oven door had shattered into a million pieces. Thank the good Lord that I was not near it. I contacted Maytag to see if there was a reason it would have done this. They said that there had not been a recall. They sent a repairman at no cost to look at it. He came, took it apart and had no reason for why it would have done this. He left it in pieces and said that he was ordering the replacement door. Maytag advised us to turn off the breaker to the oven. After a month without ovens, the repairman called and said that the part had been discontinued. HA! You think?!? It has the potential to explode. It should have been recalled, not just discontinued. Maytag offered us 20% off a new set of $3000 wall ovens or $150 to pick ours up for disposal. Talk about saving the company money and screwing over the unlucky recipient of a defective product. They ought to be ashamed. I am going to have to replace the broken glass with aftermarket glass. What is going to happen when I use the self cleaning option? What happens when the top door explodes. I am scared to use my very expensive wall ovens that I thought would last at least 10 years. Shaneka at Whirlpool said that people have appliances fail all the time and just have to buy replacements. Do all of them have to replace ovens because doors explode for no reason? I am not the only one this has happened to. I have found several other complaints of this on the internet. Why did they discontinue these door? I wonder.

Purchased new stove from Home Depot. Was delivered damaged after I opened it. Called Maytag and they cannot get a service man there to look at it. They keep on telling me I have a 30 day unconditional warranty, yet they cannot live up to their words. Absolutely amazing. Bought the Maytag because of the 10 year warranty. Do not waste your time. Buy locally at an appliance store not big box stores. Do not buy Maytag either - service is just a bunch of well qualified talkers and key punchers. Very poor buying experience.

Purchase a Maytag Bravo XL Washer Model MVWB850YWO from a major Home Improvement store in January 2012 with a 4 year service plan. Since this time I had to replace a motor and 4 (that is right 4) control panels. Although I am covered under a protection plan, the cost of laundry services and an outage of 2 weeks for each event is very costly. This time I call Maytag for support on their product. Looking for someone to say that there is something wrong with this machine. I want to hear that their product should not perform like this. I was told from a supervisor in these words that Mrs. we only care about the machine the 1st year. After that you are on your own. When did Customer Service lose the service part? When did companies stop caring about their products they produce? I never heard I am sorry youre having trouble or even a recommendation. A machine this new should not have 4 control panels replaced. This is the reason no one wants to buy a Made in the USA product anymore because we know the employees working there do not care about keeping customer relations.

Bought a dishwasher about 2 years ago, through Home Depot. After it was installed, contacted Maytag to let them know that it didnt seem to be working correctly. They sent out a repairman, who looked at the machine, and then told us that with the new eco friendly settings, it would be best to let the dishes dry overnight. It seems that the company and its employees dont know [or care] about the product. Contacted their service/helpline to let them know that the screws on the insides of the latch [on the cover] are NOT screwing into anything, they come loose. Person couldnt find same in his system, finally sent screw, but they were the wrong size and didnt work. Just opened the dishwasher this AM, after washing the dishes last night. 12 hours later and they still are not dry. This isnt eco, this is something that is wrong that Maytag doesnt want to address. Buy something else!!!

The ranges are getting great but are more so with digital than buttons and knobs which they should still have, especially for the handicapped and some elderly who prefer them. It would help prevent injuries. It was hard for me to find the knobs.

Didnt even want to put 1 star but that is the lowest you can give. Maytag microwave less than a year old paid $350. Door clasp broke. Took two weeks to send a repairman out, he came out and of course did not have the part -- took another week to get it. Fixed the door and then he crashed and burned the microwave shorted it out and now it is totally dead. That was 2 1/2 weeks ago. Maytag refuses to replace the microwave and insists that the same incompetent service company come out and fix it. Meanwhile I have to call Maytag every other day to find out when the correct part to repair the microwave will be in. Was told it would be in two days ago. Never got a call to schedule the repair, called today to find out they never even ordered the part. Here goes another week without my microwave. Not only does Maytag have horrible customer service, they manage to find unskilled repair techs with equally horrible customer service! Will never ever buy another May useless Tag appliance again.

Maytag Dishwasher control panel is not working again! We have owned dishwasher for less than two years but needed repair twice. This time the warranty has expired. We will not have it repaired again. Its too expensive! We will never go with Maytag again.

Purchased a Maytag washer and dryer 6 years ago and everything was fine until 3 weeks ago when the washer stopped spinning. We knew we were out of the 1 year warranty and contacted a repair service, who told us the bearing was no good. Contacted Maytag who offered in goodwill to pay for the parts and we would pay for the labor. A different repair person came in and told us the washer has no bearings but a transmission, which went bad. They ordered the transmission and today the repair person was in to install it. He installed the transmission, but while trying to take out the old one he dented the drum. According to my husband the repair person banged so hard that it sounded as if something could have been damaged, sure enough it was the drum. Contacted Maytag to see if anything can be done as now we still have no washer, and the repair person was their selection not ours. All we got from Maytag was they are not responsible and there is not much more they can do. I cannot believe the last Maytag product we had lasted over 20 years and this one is less than 6 years with problems. Will not purchase another of their products again.

Well Maytag, I have to say that I am very disappointed with your washer. When I put it on the bedding setting and try to wash a big load, it barely moves the load around. If you have a regular agitator to replace this useless one that is in this new washer I would like to have one. My laundry is barely getting washed and when you look inside the washer everything that is on the top stays on the top, not like the older washers where you could see that the laundry was getting sucked down with the proper agitator.

Refrigerator 1F122269VEM7 not making ice, shelves broke, freezer drawers stuck, and motor running like an automobile. Refrigerator only 2 years old. Paid 4000 dollars and this is not acceptable. Reviews online very disappointing. Other reviews on this product not good. People having all kinds of products with not resolve.

If I can rate the AquaLift Technology oven cleaning system that my Maytag oven has as a “Zero”, I would. This technology only removes some of the spills on the bottom of the oven. It does not clean the sides or top of the oven. I’m back to the olden days of using a lot of elbow grease to remove splatters and spills. They say you cannot use any cleaners in the oven either. At least with the old ovens you can spray an oven cleaner and wipe it clean. This product has taken us back before there were spray oven cleaners!

The worst washer I have ever purchased. Clothes DO NOT come out clean, smell musty after washing. Have even decreased the amount of clothing per wash. Cant use bulk load function: throws LF Code - Bad water valve. I will NEVER buy or suggest anyone buy this piece of JUNK! Then to top it off you have to constantly chase the machine around due to wash load becoming unbalanced. Now today have to contend with a burnt smell...

I purchased a Maytag Bravos washer in 2009. I have had nothing but problems. Since, it seems that this washer was never tested nor perfected but just put on the market to sell to us, the consumers, the company does not care that this washer breaks down constantly. First the pump had to be replaced, then the tub was replaced. These were nothing compared to coins falling through to get caught in the pump and cause the washer not to drain. When I bought my washer, I also purchased an extended warranty not knowing that if the washer were to breakdown to many times, Maytag would refuse to repair under the service plan that I purchased because now they are telling me that by letting the coins fall through is abuse of the washer. Really so what they are saying is accidents will not be covered, I thought thats why we purchase insurance.Thank You, Maytag. I will never buy your product again.

Big mistake. Worst purchase ever!! These high-efficiency washers (Maytag Washer Bravos XL) are the worst especially this one! I wash and wipe down the washer drum more than I was my clothes. I purchased it because it had a huge drum so I can wash my blankets and comforters. This washer leaves soap scum marks/residue on clothes and leaves it on the drum as well. I basically have to wash my clothes twice once with soap and then run again with just wash and rinse without soap, you tell me how efficient is that! Why not make a washer that put more water so the clothes can get washed properly. Dont worry about my water and electric bill. MAKE A WASHER THAT WORKS!I called customer service she asked me if I use the deep water, now you tell me why am I going to use the deep water, if that is the only way the washer is going to clean the clothes then do NOT give me 11 other options the washer to use. ONLY HAVE DEEP WASH OPTION. I dont care about the bells and whistles, I do not need a different tune when I turn it on and a different tune when its done washing my clothes. Make the washer the way it used to be WASHES CLOTHES WITH WATER AND LOTS OF IT. I will pay my bill not to worry. So I called customer service all they said was they will document my call! Well... like thats going to do me any good while I am stuck with your POS washer!

I bought a Maytag washer 1 year and 1 month ago (MVWB835DW1), Hated this washer since day one. It does not wash clothes very well, does not even cover them fully with water. The mini agitator at the bottom does not move he close it just spins on the bottom of them. Now it started making a very high pitch squeal when it spins and of course it is one month past the manufacture warranty so I call a repairman and the first thing he says to me is Im sorry for your purchase, it was a bad one and it will cost me 600$ to repair because the bearing is bad. And my bad for not getting an extended warranty but I have never had a washing machine work this bad and break within the first 13 month of owning it??? Lesson learned I guess!

I bought a Maytag MMV1153BAW Microwave. Within a year, the electronic key pad started cracking from normal use. After two years, the microwave intermittently starts then just stops, with the key pad showing 0000. We must unplug the device, or turn the breaker off and on. I called Maytag about the key pad and they said it wasnt covered, and a replacement key pad cost more than the microwave. After two and a half years, we purchased a new microwave, and have sworn never to buy Maytag again.

You cannot go wrong with Maytag, even if there were issues they are reliable in repair, and parts are available so you arent forced to purchase new like some technology. I have been pleased with the front load washer dryer since 1998.

I purchased a Neptune washer/dryer front loader. All Neptune washers have basic design flaw over which the company should be sued. Since the bulk of the weight is in the front of the horizontal wash-drum, the entire assembly is suspended by a rear mounted bearing allowing the drum to spin. That bearing assembly is woefully under-designed and not able to support the unequally distributed weight that is inherent in any front load design.Since the forces of gravity cause a loading of the rear bearing on the front of the bearing raceway only, the machine is doomed to catastrophic failure of the entire drum system--and they all do this. When the washer goes into spin mode, it sounds like a jet engine taking off and that is a symptom of the bearing design beginning to fail which begins on the first use of the machine. The cost of the drum assembly/bearing and the labor is far more expensive than buying a new machine and therefore, not worth it. Avoid Maytag products at all costs.

The Maytag Bravo is a big waste of money. Get a less expensive machine. You will have no problems and save money. This is my experience: SETTINGSYou cannot control the settings completely. Every setting is preset. For example, if you choose the Bulky setting, you cannot choose the water save spray rinse. Those two cannot be selected together. Certain settings can only be selected with certain temperatures. This will however be the least of your problems. WASHINGIt does not get clothes clean. I have had instances of items coming out with still stuff stuck to them, not just stains, but actual solid material stuck to it. My cat threw up in his bed and when I got it out, it still had small pieces of vomit stuck to it. I have always only used the Bulky setting which fills up the whole drum, so there is sufficient water to wash. I cannot imagine what it would be like if I used the Normal setting. Many times I had to wash thing twice. If you use the normal setting, you will get hardly any water. It will be a moist bundle of clothes moving like a big lump. You need water and some degree of friction to eliminate the dirt. SPINNINGIt is constantly stopping, beeping and showing me the UL sign (uneven load). You have to unravel the items and reposition them Around the drum. If you are an old lady like me, this is a real chore because the items are now soaking wet and very heavy. Also, because there is no agitator, the items come out in knots (tied to one another) and you have to separate them. DURABILITYThe lid is loose. It looks like it may be missing a screw on one side. It still locks, but it moves sideways when you close it and open it. BOTTOM LINEThe whole thing is a disaster. Get an old fashion type. It will work better and you can save your money. I honestly think there should be a class action suit against Maytag.

Purchased this washing machine 4 years ago and every time I do towels, blankets, linens etc. all ends up in the middle of the washer in an unbalanced situation. Cannot clear the balance even when rearranged. I assume this is what happens with all the upright washers now that the center agitation unit has been removed. I have to ask the question of who made this decision to remove the center part? A man who never does laundry?

I bought this range (Gemini Double gas range) in 2010 but was not installed in my house until 2011 due to time delays in kitchen re-model. I paid $1310.00. It was serviced 3 times once under warranty. About a year ago the igniter went in one of the ovens for the second time and one of the stove burners wouldnt light. Since the other oven and 3 other burners worked we didnt call for repair, then a second burner stopped working and we called our Maytag dealer. 2 different service techs came one with more experience and both said the same thing the stove wasnt worth fixing due to cost of parts. One of the problems was the screws in the burners couldnt be removed due to rust and deterioration of the screws. They would break and cost other components also to be needed. So after 7 years of use and already having repairs done I have to buy a new stove. It will not be a Maytag. I also bought a top of the line Maytag dishwasher and one month past the 5 year warranty the electronic panel burned out. After calling Maytag and complaining they did agree to pay for the part close to $300 but I still paid for labor. When I looked at reviews for the oven before purchasing they werent too good but wanted a double oven at the time and always had good luck with Maytag in the past. I thought buying a higher priced model would be better quality. Not so. After calling Maytag today the best they could offer was to buy an extended warranty for $380, I declined. My advice - Listen to the reviews. The Maytag repairman isnt sitting around idly anymore!

Maytag Bravo X-We bought this washing machine not even 4 years (February 2013) ago from Lowes. We had this issue before the warranty went up a couple of times and then it stopped and started working fine. We contacted Maytag before... But of course beings the issue resolved there was no way to send someone out here to troubleshoot the problem. Now it is doing it all the time. A few months ago it went out of warranty. We are having issues with it going into the spin cycle and it will stop there and it will not spin out my clothes and finish draining. Contacted them and they want to charge money for a service tech to come out just to look at it. Lord only knows how much it would cost to fix.

We currently have had our Maytag washing machine for approximately 15 years. The first thing we noticed was how user friendly it was. Also, the options that came with our washing machine met all of our needs. The second thing that we were excited about was how quiet it was. Our previous washing machine could be heard at the back of the house and was constantly out of balance. The third thing we noticed was how much cleaner our clothes were. Our clothes smelled better and had less wear thus saving us money. Speaking of which, the machine is an energy saver. One of the most significant attributes I can attest to is how reliable it is. There has never been an issue that required repair services. I am sure our Maytag will be in service for years to come. c

I purchased a Maytag Bravos washer and dryer pair in 2009. Over those 5 years I have had at least 8 shirts come out of the washer with tears in the armpits. First I thought it was my armpits destroying the cloth. Then I thought it was cheap cotton (all my shirts are 100% cotton) from foreign manufacturers. Ive had two shirts destroyed this week, this mornings was really thick material. Usually when I remove clothes from the washer, they are entwined and twisted. Consistently when I wash any load including a towel or two, the washer becomes unbalanced. My clothes often have a foul odor after washing. My theory is that the lack of a center agitating spindle is allowing the clothes to tangle, and not really cleaning them. I have to use the extra rinse setting or the clothes come out covered with soap suds. In summary, Im not happy with this washer and will never buy another Maytag appliance. Im also not sure the high-efficiency technology has had all the kinks ironed out.

I purchased a stainless steel (freezer bottom) Maytag refrigerator Model # MFI2670XEM0 in Oct 2012. Since then its been a nightmare. The repairman has been out four times, once being a week after I purchased it. It leaked and ruined my kitchen floor. Call Maytag, they didnt want to hear about it. As of this moment, I have three more things broken on the unit. My ice maker literally takes 3 days to make ice, the alarm on the door is broken, and the plastic crisper cracked and now will not stay in. Called Maytag again and they stated that they will not replace the item with one of equal value. They just keep repairing it. I will NEVER EVER buy another Maytag product again. I spent $1700 on this product and had faith in the Maytag product. That will never happen again. Shame on Maytag for not standing behind their products.

We bought this washer before Christmas. I was very excited. However my clothes don’t come out clean. I am actually washing my white uniform with hands because each time I wash, dark scums remain on my clothes. I think that the machine sensor does not sense how much clothes are in there and how much water is required. This machine is very disappointing, it needs to be recalled. See pictures below.

Bought this (Maytag Washer MVWB955FC1) on 1/8/18, was delivered late in January as it was on back-order. On 4/30/18, during a cycle, the washer made a pop sound. There was glass everywhere. The glass had shattered and exploded onto the floor and washer. The glass is on the inside of the drum and all over the clothes. Contacted Maytag and they sent out a repairman the next day. Repair said there is a point of impact indicated I dropped something on it. NOTHING was dropped on it. There is a point of impact, from the inside. The glass is pushed up and out indicating pressure from INSIDE the washer.Repairman says its not covered under warranty and that I had to pay for his time as well. He also said there are no known issues with this lid and washer. The lid is out of stock and wont be available for a while. I called Maytag and they gave me the same response, never heard of this.. and lid is out of stock. I found SEVERAL reviews/complaints in which, for the exact same model, this has happened to other people. This glass lid is dangerous and poses a serious safety risk to households that contain it. If they replace the lid, there is no guarantee this will not happen again. A child could walk by the washer and at any moment the glass lid could explode, send tiny shards of glass everywhere. I want a refund for this dangerous washer.

On 11-10-10 I purchased a top of the line Maytag fridge. All had been great till we needed a part in Nov. of 2014! After nearly 3 months of searching they tell us that they no longer make parts for this unit and I am out of luck! Fridge works great but the center seal is broken (french door - Mullin) they quit making the part???? I am beyond angry! Will never buy Maytag again!!!

Maytag washer, dryer, oven, microwave over-the-range - all crapped out in four years. I will never buy or recommend Maytag. I believed them to be one of the best brands but apparently theyve learned a few too many shortcuts.

I love my Maytag. It does a good job, however, it takes almost an hour to run one load. Also, if you have a heavy load, it doesn’t spin long enough so your clothes are dripping when you take them out.

Maytag/Whirlpool dishwasher control panel FAILURE MDB7749SAM - Just like all the above comments about this dishwasher... I too have been a victim. Control panel stopped working after 1 1/2 years. Turned on by itself like other have commented and will not let you push any buttons. Maytag/Whirlpool refuses to do anything about this at all and will cost me over $250 to fix an appliance I purchased at $499. How disgraceful of a company to not stand by their product... A huge shame on you Maytag/Whirlpool for not standing behind your product. If anyone knows of a way to get involved with a class action suit against this company I would like to get in on it.

I purchased a Maytag Gemini gas range in July 2006. Rust has appeared on the bottom of both oven doors. I called Maytag customer service, realizing that my range was no longer covered by warranty. However, I feel the paint on a range, costing over $1,000, should last longer than 5 years. Customer service told me to call a repair technician. When I asked who would pay for this service call, they didnt even bother to respond to me. As I have read other reviews of dissatisfied Maytag Range owners, Im glad I didnt waste money calling a repair tech who would do nothing to help, but charge a $100 plus fee. The paint on a car, which is subjected to all kinds of weather, lasts much longer than 5 years. You would think the paint on an appliance inside a home should last much longer. This rust is becoming very unsightly. I will certainly not purchase a Maytag product again, as the company has proved they do not stand behind their product line.

We bought a Maytag appliance package when we built our house in 2015. So far the exchange Fan burned out in the fridge. The element burned out on the range. The wheels broke off inside the dishwasher on the racks inside and the outside of the white dishwasher is rusting worse than 1959 Edsel. 3.5 years old. Broken and rusty. I called and emailed Maytag customer service and all they say is it’s out of warranty and they’re sorry. Things break I get it but if they said on the box when I purchased it that it would rust in 3.5 years I would have looked at and purchased another brand. Beware of the cheaply made poor customer service of the new Maytag.

I purchased a Maytag (as Maytag was always rated the Best) and from the start was not happy with the product. I contacted Maytag (Whirlpool, the makers of Maytag) and was told to get stains out, you had to pre-soak and scrub the area... really? Then I might as well just hand wash all of my clothes and hang to dry. I would not need a washer. My clothes do not come clean at all. DO NOT PURCHASE A MAYTAG (or I think any washer Whirlpool makes as they do not back their products).Prior to this, I had a Whirlpool washer with agitator and loved the washer. Clothes were always clean, and I did not have to pre-soak stains for them to come clean. Go Figure! I have never been so disappointed in a washer or company. I am now looking to purchase a new washer as I have had it with this one... and it wont be a product made by Whirlpool.

So wife and I purchased a Maytag dishwasher in late 2012. A year and a month later it turns into Hal 9000 from 2001 Space Odyssey. I press normal, it shows light rinse. I press heated dry, it tries turning off the life support and blowing me out the air lock. Finally, in March it dies. No power, no nothing. $500+ for an appliance that lasts 2 years. So for the past few months, while we wavered over buying a new brand or spending $250+ on a repair, we were washing dishes by hand. It was as bad as my grandma used to say it was. Then, by chance I ran across a web blog talking about this being a common problem, and there are hundreds of complaints, and its a problem with a $4.00 part on the control panel that can be fixed with a Q-tip, rubbing alcohol, and silicone... Im not a handyman by any stretch of the imagination, but even this I could do. Unplug or switch off the breaker. After unscrewing all the screws, (not your standard or Phillips head either) unplug the control panel from the control box and remove the control panel. On the back, youll notice a flat cable (pictured below) that will have dark marks on the opposite side of the part sticker. Gently clean this with a Q-tip and rubbing alcohol. I then covered the back (side without sticker) with silicone, (you can get at hardware store or Target) let dry, and put everything back together again and now its working better than new. Im regarded as a master handyman in my house, and I didnt even have to hear the dishwasher sing Daisy Bell as I disconnected it. With such a simple fix, Im amazed Maytag didnt just own up to it and get it addressed. The millions it will end up costing them in the long run, by this frustrating experience shared by us all will have them thinking twice in the future (hopefully). It is a shame they seem to be adopting the business model of American auto manufacturers of the late 80s. Ill update this in a year and a month to let you know how the fix worked, and you owe me a beer for saving you $150 - $600 for a repair or replacement. One word... VICTORIOUS!!

On June 17, 2013, we purchased this over the stove microwave for my elderly parents. They use it daily to heat their lunches. In December 2014, it would stop turning and finally in January 2015 it completely died... no heating and no turning. The technician quoted a repair at $200 when we only paid a little more to purchase it. I emailed Maytag to tell them that it was manufactured and purchased in 2013 with light use and that it should never have died in such a short period of time. An e-Solutions Specialist contacted me to tell me that they certainly understand my frustration, but that occasionally failures occur and that there was nothing they could do. I replied back that they could DO something because they were customer service and that was there job. No reply back yet, but after seeing so many of the same issues here, Im not holding my breath and I would never buy or recommend a Maytag product of any kind to anyone. I dont expect 15 years from an appliance, but I certainly think 18 months is just wrong.

I have a Maytag Bravos XL and have white residue on all the clothes that get washed in this machine since I purchased it. I have always used HE Detergent and have followed all Maytags recommendations to reduce the white residue to no avail. I had to wash my clothes 5 times to get the residue off of my clothing and 4 of those were without any detergent and on all temperatures and wash cycles. Model # MVWB835DW.

Original owner of $800 HE top loader washer since 2010. We heard a grinding noise for months, then finally it seized up. Repairman quoted me $300 to replace bearings. The repair guy seemed a bit too eager for the job, so I knew it must have been easier than expected. I Googled the heck out of it, and used this forum heavily for guidance. Seems the bearing failure is a pattern issue. It also seemed ridiculously involved and no one had posted a how to video matching my model’s layout. I took a peek with my own eyes and noticed a sock had gotten under the basket. The sock got caught in the drive belt and knocked everything loose. I removed the debris, tightened the pulley and everything worked. Cost me $0 to fix myself. So buyers beware before repair. And check the error codes yourself when in doubt! The first thing I did was check error codes. Found a great video here **.

I purchased this machine (MVWB765FW0) because I had a good experiences with Maytag in the past. There is a manufacture defect in this particular machine. If I were you, I would not buy it. I’ve lost two sets of bedsheets and my wife had a dress that she loved that got ripped up at the bottom between the agitator and the base of the machine. Maytag knows about the problem and does not have a solution.

We bought a Maytag refrigerator bottom freezer at Home Depot in 2012/10/15. A few months ago, a sheet of ice formed on the bottom of the freezer. Since the warranty expired, I decided to look at the problem. Now, I am a mechanical person who usually can fix just about anything mechanical. I used a hair dryer to defrost the freezer and saw that the drainage hole was frozen over. I took the entire freezer apart, cleaned the drainage channel, the drainage hole and reassembled the freezer. No more than 24 hours later, the drainage hole was covered with 1/4-1/3 thick ice, the drainage hose and the tray were dry, and the bottom of the freezer was coated with ice. This one problem that I could not solve. The design is so poor, the draining water freezes over the hole before it drains. I read some of the consumers complaints and I just want to add that do NOT waste your money on repairmen, or parts from Maytag, the refrigerator is NOT repairable. I will write off my loss of $900 and look for a new refrigerator, but Maytag will never see my money again.

We purchased a front-load Maytag washing machine (Model MHW3505FW1) two years ago this month. When the machine is empty, we always leave to door open. We dont allow clothes to stay in it for long, never for more than a day (the load is usually changed as soon as the cycle is over). Right now, the rubber seal on the front has tons of black mold on it, and when I lift the seal to look underneath, its way worse. There have been many problems like this reported on front-loaders. Wish Id known! Maytag will not send a replacement seal.

I purchased a Maytag Bravos XL washer mid November 2013. Less than six weeks later it leaked water. The repair person has been to repair it four times. The last visit was yesterday. It now has more problems than it originally had. It still leaked water. Maytag does not stand by what they sell. All they say is they will repair it. My caution to anyone reading this is never buy a Maytag appliance. I hope this review helps someone in their decision making process.

Great when it works properly and doesnt leak! Quietness, cycles. Everything that had to go in went in, well laid out. Stainless steel, clean, good looking. Anything with the Maytag name doesnt last any more than a couple of years. Gone through a washer and dryer with no help from Maytag. The dishwasher was replaced by Maytag because the main circuit board was on backorder for more than 5 months. Washer was replaced with a Samsung. If I had to replace the dishwasher out of pocket I would go to Korea or Europe to do so. Maytag, what a huge fall in quality and reliability!

I had the washer repaired twice in January, once in April and again in August, the same repair wire coming out of harness. I had to pay a second time before Willie, the repairman, finally put a longer wire on the harness. Maytag told me they would send a new repairman after I called to complain. All 4 times, its been the same man and it cost me money. It seems like a bait and switch with the repairman. I called both A& E and Maytag. Both refused to refund the $129 second charge because it was more than 90 days. I say its been the same issue, repairman is a scam when they dont fix it right and charge again. I had another man there who knows about repairs and finally told the repairman to change out the wire or it wouldnt have been done this time either. I do want an attorney to contact me about this as this is wrong. Im going to file a complaint with BBB.

We have had a Maytag Bravos XL top load washer less than a year. Big Mistake. It was JUNKYARD ready when it came out of the box. Does NOT wash clean. Weve tried everything.The agitator looks and acts like a toy. Will not run enough water to wash anything. We had a LG front load before and its hard to get use to having dirty clothes. NEVER AGAIN.

I have a Maytag Performa washing machine (model no. PAVT234AWW) and called the Maytag parts department to order a plastic pulley for the main drive motor. I was told I would have to purchase the 189 dollar motor just to get the plastic pulley. After two days web searching and calling local appliance stores I found that Whirlpool who uses the same drive motor sells the pulley (part no. 21001108) for 9 dollars. The Whirlpool pulley is even made out of stronger plastic. I just wonder how many Maytag customers have had to purchase a drive motor like I was told I had to by Maytag just to fix a 9 dollar pulley. I got lucky and my problem was solved, but only because a local store happened to have this particular problem so frequently that they were able to help me out when Maytag should be the ones helping out their customers better. Thank you for your time.

I would like Maytag to repair or replace this dishwasher. It has only been installed since November 2014. The only button that works is the auto clean. None of the buttons work. I thought Maytag was a reputable business.

I purchased a Maytag dishwasher because they are supposed to be known to be a good brand. But my dishwasher is 3 years old and it started rusting around a steam vent on the outside of the door! This issue has been ongoing but as Ive been busy, I havent had the time to address the problem with Maytag since its out of warranty anyway. But I feel like this should not be a warranty issue to begin with, it should be a recall issue. I had a plumber look at this, and he said that it was caused because the vent was not properly sealed during manufacturing. Now it looks as though mold spores are growing inside the steam vent! Maytag will not stand behind their product, so why should I invest anymore money into it?! I would rather purchase another dishwasher (OTHER THAN THIS BRAND) than dump another penny into this garbage dishwasher!

I bought this machine because it has a (deep water wash), which means there is a lot of water, enough to cover the clothes, at least I thought so, the salesman seemed to think so as well! But no, it does not come close to covering the clothes, false advertising! I must put my clothes in a large bucket, soak the clothes with water, then bring the bucket to the washer and empty it into it, because of the weight of the water, the machine adds almost enough water to cover the clothes.Another big problem with this washer is the fact that if I lift the top in mid-wash, while I do something, not wanting to listen to the irritating sound it makes in my apartment, after 10 minutes it starts to drain and there is no way to stop it, I must wait until it completely drains and restart the machine. This machine has the stench of government on it!!! My advice, keep your old machine.

We purchased a Maytag gas range, only to have the paint wash off the front trim of the oven door. The digital panel went out in the second year of use and is apparently expensive to replace. After going through reviews by other owners and discussions with repairmen, it was determined that these panels only last about a year and are defective. This problem is extensive with Maytag. My brother was a repairman for them and dropped them due to poor quality of workmanship in appliances and their dishonest approach to warranties. I should have known better. Dont ever buy Maytag!!!

Maytag Model #MGR7662 range - We inherited this oven when we bought my mother-in-laws house 2 years ago. We had to get a thermometer to keep in the oven since the temperature is never consistent and is usually 50-100 degrees lower than the digital readout. We will be replacing this oven as soon as we can and it will NOT be a Maytag.

These machines have lots of service problems, although Im not familiar with the newer models. The function and the features are adequate, and typical. And overall, again, I have no complaints other than shortly after purchasing, there was a circuit board recall for these machines, and fortunately, I had a repairman who knew of the issue, and guided me to a cost free fix. Overall, it has served the purpose well of cleaning my clothes in a decent fashion.

I like most others have experienced the same issues with the new Maytag top load WM. In addition my new machine dances across the floor like a drunk leprechaun. After Lowes told me that with my extended warranty Id have to miss work and pay 100 bucks for a service call I emailed Maytag. Needless to say they didnt even respond. Ive have learned a few valuable lessons. Dont assume that more money means better merchandise. Made in America doesnt say much. And please dont buy Maytag.

Maytag Centennial - It came with the house. I think its a line made special for rent-to-own kind of places. I cannot stand the washer. It will not take fabric softener unless its in the ball and if you use extra rinse you dont get to use fab softener at all. (I like liquid fab softener on some things). Why it doesnt have a dispenser is beyond me. And the bleach dispenser is poorly designed, too close to the tub and splashes every time. Ive had this six months and would get rid of it in a heartbeat if I could afford to. Plus it snags towels. The washer is crap. And its a Maytag. I wish it would break so I could justify buying one that has some decent features like fab soft dispenser, bleach dispenser that doesnt splash, drum that doesnt snag.

My Maytag Front Load Washer Model MHWE200XW purchased from Sears had a malfunctioning spin cycle. The authorized Maytag repairman from Landers, with support from a Maytag technician by phone, did not know how to repair it. The machine had light use over the past 15 months, and hence was not covered under warranty. So I am out $650 for the machine and $200 for the repair that resulted in continued and even worse malfunctioning. Unfortunately for me, the tests did not show any errors and the machine did not state any error. It just would not spin and then would not allow the door to open. It is a lemon and I do not recommend its purchase.

We bought the combo Maytag Bravo 300. The issues with the dryer are that it doesnt heat right, have to run the thing twice, after the first 50 minutes the clothes are still damp and it sounds like its going to take off. We had a service man tell us that it was the fan blower rubbing. Now for the washer. It sounds like a b-52 taking off in spin cycle. I know that its the bearings, bearing kit 80 some dollars plus the bearing tool another 80 some bucks. Dont think Im going to invest in Maytags game. If there is ever a class action lawsuit please put me down or notify me.

Maytag washer model MVWC416FW1. This is the worst washer ever. I only had this washer for 1 year and 2 months. Oil leaks from the bottom all over my floor. The washer is soooooooo loud you can probably hear it down the street when it is on spin cycle and the start button works when it wants. I called Maytag and they told me if a service man come it may not be covered and I will have to pay out of pocket. The 10 year warranty listed on top of the washer and dryer only covers the parts not the labor. Very disappointed. Its a good thing I purchased an extended warranty but I dont know what will they do. 1 year and may be buying another washer. It DEFINITELY wont be a Maytag. If I could rate this a 0 I would.

MFI2568AES - Last night we woke up because of a noise coming due to continuous snapping of the waterline against the walls of the refrigerator as well as a wall of the house structure itself. Very loud noise. I pulled the refrigerator, went behind it, and shut off the waterline. That stopped the noise and allowed me to go back to sleep. However, need your help to resolve this issue. I will appreciate if you can offer me pointers and guidance.

This is undoubtedly the worst washer I have ever owned or used! I have never before felt compelled to write a review on a product, but I wanted to make other buyers aware. There is not enough water to clean the clothes - the water level doesnt even cover the top of the clothes, so the top of the clothes are dry as they are agitating! After drying (dryer doesnt dry either) the clothes do not smell fresh or clean. Ive put up with it for 3 years and am disgusted every time I use it. Im just about ready to buy another set.

Rust on two year old Maytag Bravos washing machine - I noticed some rust along the inside lip of the washing machine lid and along the seam near the top of the machine about a week ago. I contacted Sears where we had purchased an extended service agreement. However, the agreement does not cover rust. I contacted Maytag and there is nothing that they can do either. The machine is kept inside the house in the laundry area. We have had two washers in the past 21 years that my husband and I have lived at this house that were much less expensive than the Maytag Bravo. They did not rust. This will be the last Maytag product we will purchase.

When I went to whip down the small shelve under the knobs, I cut my finger on the sharp metal. Was told that is the oven vent. Checked out your instruction book and found NO mention on that being a danger and to take care when cleaning. If I had been informed of that sharp metal piece I dont think I would have looked at your stove. The metal has razor sharp edges on both sides making it almost impossible to get too close to cleaning it. That shelf is a nice place to collect dust, grease and food boil overs and now I have to be extremely careful about cleaning. Thanks to someones not thinking in their designing. The stove is what I wanted other than that one fault.

Purchased Bravos 300 quiet series wash and dryer 3 1/2 yrs ago new. 18 months ago the washer gives me f51 and ul codes. To repair this USA made washer will cost over 250 dollars. I see why the Maytag repairman is not busy. Cause after 2 years you gotta buy a new one. All these digital controls are made in China - junk. Ill buy LG or Samsung next.

My husband purchased the Maytag Bravo December 2013. We immediately started noticing clothes been destroyed and stains still in clothes. We immediately contacted Whirlpool and shared our concerns and they sent out technician. He stated that the motherboard was gone. After repairing the motherboard, that do not stop our clothes from being destroyed and making them clean. I have wrote numerous letter to the CEO of whirlpool and sent pictures. When they decide to call you back months have passed and still they do not want to help you. Whirlpool have refused to take responsibility for a bad product they invented. They do not stand by their mission. Someone please help the consumer, because this big corporation refuse.

Have had nothing but trouble with this fridge! Ice forms at bottom of freezer with frost all over top shelf. Ice maker no longer works. 3 years old for goodness sake. Had repairman replaced all lines, and still have the problem. Heard you have to unplug fridge for 24 hours to solve problem EVERY 2 Months! I Guess the Maytag repairman stays lonely because they dont stand behind their product! Hate it!!

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

We bought a washer & dryer from Home Depot 2 1/2 years ago. The control board went out on my washer. I called Maytag and they wanted $109 for a diagnostic fee and wouldnt tell me how much the labor would be. A control board costs $350. So by the time all is said and done... the money would be better spent buying a new one. Maytags slogan of dependability lasts is a bunch of hooey. Washers should last more than 2 1/2 years and Maytag should back up their appliances. They just lost a customer.

My wife and I purchased new Maytag dishwasher in 2011. Worked well for 9 months and then control panel went out. We bought a Sears with 1 year warranty. Sears fixed but then 2 more repairs followed with blown fuse and pump motor went out. We knew this was a lemon so we purchased an extended 3-year warranty through Maytag. Well the unit only works for a month or two then we are constantly calling for repairs. We just had the pump replaced a 3rd time and yep you guessed it the unit is loud again so here comes repair 15. The warranty contract states that if the same part fails 3 times, Maytag will replace the unit new one time and voids any further repairs. My wife and I are very frustrated and lost all confidence with the Maytag company. Our old one lasted 14 years and this new one is a piece of junk. The company reviewed my request of unit replacement but was denied for whatever stupid reason. This unit has over 5000 dollars worth of repairs not counting the lost time of appointments waiting for the repair. My wife has had to stay home and wait for 4 to 8 hours an appointment. She has many other obligations to do with her time. Its sad that Maytag does not stand behind their product. Its my conclusion that this company does not want to sell good product, they only want to sell extended warranties. Your products are not reliable if you have to offer warranties. I would like to see if I can get to repair 30 before my warranty expires by March of 2015. Maybe I could then see if 30 repairs would make the Guinness Book of Records on the most repairs done on a dishwasher with extended warranty. That would be something the company could be proud of dont ya think.

This is the worse washing machine ever. Wish Id never have bought it. Clothes come out unclean, washer cleaner cycle doesnt work, water level is almost none, etc etc. I could go on and on, you get the picture. Coming here and seeing 100s of negative reviews and complaints many of which I suffer from as well, just clarifies how bad this machine really is. There has got to be a way to bring a class action lawsuit or arbitrary suit against them. Im pretty confident that there are probably 100s more who are dealing with this shoddy washing machine as we all are.

WE bought all new Maytag kitchen appliances and the extended best service contract. Cost 1/2 of the cost of the appliances. This was 3 years ago. Recently dishwasher went blank. Service call was a factory neutral wire. Then ice maker replaced with a reman unit. Then we thought something was wrong with the oven cleaning system aqua lift. So after many hours and calls two service techs told us the system will not clean the oven and after many cycles it will not and the bad part is they are still selling this system to the public. Criminal. I think they should own up to the public when they do this kind of thing. On top of this I would go buy the self cleaning oven but the tech even said he will not use it because it will break and need replacement. It is no better other than you can use oven cleaner to clean the finish without the heating element and you cannot use anything that works on the aqua lift finish. Bad deal.

Control panel is defective on my Maytag dishwasher. Found a phone number that was created to deal with this problem. I only had to hold for a few minutes but the first person I spoke to was rude and unhelpful so I asked to speak to someone else. When another agent came on the line I told her that only the normal and rinse button light up but do nothing when pressed. She arranged for a repairman to come to my house and determine if my control panel is defective at their cost. When he arrived he asked me what the problem was and I said, The touch pad control panel is not working. He stated, Your control panel needs to be replaced. I have to order the part and come back to fix it. He was there for about five minutes and he never laid a finger on the dishwasher. When I asked if the control panel design has been fixed he said, No, you will probably have to replace it again.There is a video on the internet that shows how to seal the electronics with silicone. The repairman said that they cannot seal the electronics unless Whirlpool provides a kit to do it. I guess the Maytag repairmen may have to come out of retirement. My husband will seal ours after it is replaced so we hopefully dont have to deal with this problem again. So now I am waiting to see if he returns in a reasonable time frame and gets my dishwasher going. There is a class action suit about this issue filed in 2013 about this defect.Updated on 09/23/2015: A repairman came to my home on August 20, 2015, at Whirlpools cost, and he determined my touch pad did not work. He informed me that Maytag would provide the part, free of charge, but it would cost me 85.00 for them to come back and install it in 2-3 days. As of today I am still waiting for the part to come in, apparently due to high demand Maytag was out of touch pads, which were out of stock. No idea of when that would be, the repairmans company said, dont call us, we will call you when the part arrives. So I began to look for the part myself, found a couple on an auction site, but most companies that sold parts were on backorder. Until I found a company that said their inventory was out of stock but they had five, stashed in the back. The price of 105.00 was not that much more than the 85.00 cost for the service call. Got it in two (2) days, installed (in about five minutes), sealed by my husband and I loaded it and washed my dishes. I was so overcome with relief, tears came to my eyes and I almost fell out. I give five star to the fella that had the part stashed until I needed it.The Maytag repairman is still waiting for the part so he can fix my dishwasher.

We bought a Maytag refrigerator Model # MBF 2254HEW, Serial # 14560744NG. It worked for 7 years and now its dead. Well it does blow warm air. We are told it cost so much to fix one that we would be better off to buy new. I bought an extended warranty but of course all is out of warranty and Maytag is sorry for the inconvenience and that parts do fail. I am going back to using the old style refrigerators that last rather than paying an enormous amount of money to buy something new and looks nice but will only last a few years. When is a recall in order? When are companies required to do better for the customer? We are told that the compressor might be OK but it could be low on coolant but it is very difficult to find a leak.

I purchased this set of Maytag Centennial Washer and Dryer from my local Home Depot in Dec. 2011. I havent had a repairman come out yet, but I am extremely dissatisfied with them. The washer is a problem because it doesnt seem to fill up with enough water to wash the clothes. Also if you want to add something to the washer that you forgot you stop it, and go to restart it again, and it starts removing all of your soap and water again. This is a waste of money, if you cannot stop it and start it again without it filling up again. I would not recommend anyone buying this HE washer & dryer. Also the dryer seems to heat up too hot to me.