I bought the washer/dryer a few years ago. I did not realize how they do not own up to their reputation. Rather expensive. My clothes are always twisted together when finished washing. Parts of them feel dry. My dryer seems to be ok. Comforters are a pain as the load always gets unbalanced. Lately it wont finish a load. I get LD all the time. Have to unplug the washer and wait for it to cut off before cutting it back on. Then I cannot just rinse or spin. It fills back up with water and I get the same LD again. If I had seen all these reviews before I bought this set I WOULD NOT have bought them in the first place.

Model MDB7749AWB2 Dishwasher - we purchased this dishwasher 3 years ago on 12/23/2011 and it appears to be falling apart. We have replaced two thermo fuses, one door latch/switch and now need the front control panel and handle because two mounting locations for the six screws have broken off. I truly expected a much longer product life than three years when I purchased a Maytag. So much plastic in crucial high stress areas must have slipped by the engineering folks. Or was it just cost cuts. I believe it will be a long time before I consider a Maytag product again based on this one. Thank you.

Purchased a Maytag based on previous models that worked. Now when I do a load of wash, no matter how large or small, the clothes are still wet after the full spin cycle is finished. This has been going on for a few months. There are only two adults so the machine is not in constant use. We have had the machine 9 years and frankly would never buy Maytag again.

I bought a Maytag Bravos XL washer in 2017 for around $800 which suddenly stopped working about 1.5 weeks ago. The console wont turn on. I filed a service request on Maytags website which results in Maytag subcontracting the job to a local appliance servicing company. About 10 days later the appliance tech shows up to my house. I had to pay $125 to the service company for the technician just to show up. After, he tinkers with the machine and 5 minutes later gives me a quote totaling $789.07. Of that amount the parts component was $482.09. He told me that the computer was bad. I was appalled. This was a 2.5 year old well kept washer. I called Maytag company next day to see if they could at least cover the parts cost. Especially as I have a large family with 3 kids plus elderly family members. After waiting 33 minutes on the phone, the CSR took all the appliance info and tried to see if she could get Maytag to cover the parts cost, given my situation. After about 5 minutes, she told me that Maytag declined my request- quoting that my appliance did not have any warranty and that the notes on the computer regarding my appliance indicated that it was field scrap. Field scrap?? Really? This was an appliance that was bought at Home Depot.This is the lowest of lows that this company (Maytag/Whirpool) can stoop. For a billion dollar company, that are advertising their products as Made in America, they have no heart and no empathy for their customers. They build sub-standard products comprising of cheap parts so that their products only last a few months, then they try to sell you their sub-prime warranty services that are full of holes. And for those poor souls that dont sign up for their warranty services, God help them if their appliance breaks down. They are then left to deal with Maytag/Whirpools appliance service vulture contractors which in tandem with Maytag conspire to squeeze every last cent out of hard working Americans (Especially during these trying times).Just to compare my situation. My parents bought LG washers and dryers in 2008 which remain in full working operation to this day (12 years in operation). The Maytag Bravos broke down in 2.5 years. Use my experience as a lesson. Do yourself a favor and save yourself the headache and heartache. DO NOT, I mean DO NOT purchase or support Maytag/Whirpool appliances. You are better off spending your money with LG or Samsung.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

I own a 2004 Neptune front end washer that Ive dealt with the terrible smell of stagnant water since I got it. Now the motor went and I was told I need a new washer even though the product warranty information clearly states the motor is covered for up to 10 years. The repairman told us that the motor thats in my machine is no longer being manufactured. How is that my fault? I do not have another $800.00 for a new one, which is now not even a lot of money for a washer. Ive already bought 2 washers since I built my home 14 years ago. Its just not right!

I almost didnt write this review because it is just a repetitive representation of this machine. I AM SO DISAPPOINTED with this machine! I had a Neptune and after a few years, it started to spew oil onto the laundry WHILE it was washing! It ruined so much clothing before I figured out what was happening. Came to find out, it was a glitch with the machine that the company SUPPOSEDLY, sent out notices about but I never received. Now the Bravos X... Bought to replace the Neptune, as it was advertised to replace Front loaders. Would accommodate a KING SIZE COMFORTER with no problem... Got out of one problem to get into another!!!From the beginning, I wondered how does this machine get the clothes clean? How would it was a king size comforter? It doesnt agitate like the other top loaders. I figured it was a new top of the line kind of technology. My clothes started to tangle up really bad even though I was not filling the machine over excessively. The clothes were staying dripping wet over and over again. It doesnt matter how much clothing is being washed, they stay super wet. I have to go through the Drain & Spin cycle to finish the cycle. IT GETS OLD!!!! I HATE THIS MACHINE!!!! Doing laundry is a HORRIFIC CHORE for me. This machine is TERRIBLE. NEEDLESS TO SAY, I CANNOT WASH ANY SIZE COMFORTER!!!After reading all these reviews, seeing how Im NOT the only one who is going through all these problems with this machine, I refuse to call any repair company! I wont spend another penny on this monster!!!! I WILL NEVER BUY ANOTHER MAYTAG ANYTHING AGAIN!!! Reason for this review... So anyone who is considering buying a Bravos X washer, think again. Hopefully you are doing your homework and will not make the same mistake we did!!!! Thank you for your time and attention to this matter.

Purchased a Maytag OTR microwave in May of 2017. Started having issues with the Open/Close Door malfunction by September. Repair came out and essentially told us to keep opening and closing until it worked. It is January 2018 and the issue has gotten worse. My question is, since Maytag is keenly aware of the problem and has for years, based on other reviewers on here, why hasnt a class action lawsuit been filed? These appliances are expensive and it sounds like many of us have been taken to the cleaners!

Maytag French door, bottom freezer - Water accumulating on the freezer drawer gasket. After a short period of time, mold forms which is a potential health hazard. We asked Maytag to look at the problem. So far, 3 service people have come around - each one with a solution, but none have been successful. I called Maytag again and left messages on two different occasions, and they have yet to get back to me. Am I on the blacklist? This I know for sure - this is the last Maytag product to ever get in to my house again. If anyone has a solution to our problem, we would love to hear from you.

Washer breaks after 2 years. I purchased a Maytag Bravos XL washer from Lowes just 2 years ago. One of the main driving factors for the purchase was the Maytag brand. The repair tech just told us the bearing was bad and we need to replace this and the drum. The service call was $100 and the repair will be over $500. I can purchase a new washer for this. I strongly recommend not buying any Maytag product. The brand used to stand for quality but not now. I dont think the Maytag repair is still the lonely tech they used to be.

The Maytag Commercial Technology wash machine, the one with the clear top, leaves soap residue on our clothes. We have tried different detergents, always high efficiency, using the extra rinse, using the deep fill and nothing works. We have tried cleaning with vinegar and using the clean washer cycle. We had 2 technicians look at it, one tore the machine apart, both said nothing is wrong with the machine. So, we are left to believe that we are stuck with a machine the leaves soap residue on our clothes as Maytag will do nothing for us because of the assessments of the technicians.

We purchased a Maytag washing machine top load (#MVWX550XW) on 12-20-2010. The switch on the machine that starts it running when you close the cover went out under warranty. They put a new switch in and it only lasted a while. I had to pay this time, $240.00 for repair. Now again, 1-2-2013, the switch is not working. I think that it is a lemon. I called the company and they will not cover the cost. Instead they want to sell a warranty for over $300.00 for one year and then if I purchased it, then they would fix it.If I did that, I would have more money into the repairs then what the machine cost ($583.44). Isnt there a lemon law? It looks like I will have to get rid of this machine and buy a different brand. Yes, Maytag has let me down. I cannot recommend their products because of the quality and answers that they give. I cannot afford an attorney, which leaves me upset when somebody wont cover the cost of the third repair.

My Bravo washer does NOT clean my clothes. I have tried many detergents. I have to pre-treat all spots with dish soap and run hot water over and then rub the spots out. This was the only recommendation given after consulting with Maytag. I have to pre-soak my clothes in a pail of water with detergent. The water is brown. My clothes are dingy, spotted and have bleach spots. I am very careful so this is not from pouring into the bleach dispenser. Maytag was the reason I purchased this washer. Never again.

We purchased this dryer a Maytag Model MEDC200XW3 about 10 months ago. The dryer slowly over time began to take longer to dry our clothes. After watching it work and seeing that the airflow in the tube was not flowing well, I noticed the lint trap was not functioning well enough and over 50% of the lint was escaping the lint trap and plugging up the exhaust vent. I asked Maytag for a service to repair my dryer and explained my findings. The service person on the phone wanted to send me a lint brush. I told her to send a repairman. The repairman said that all lint traps let lint by and said it was my problem. Well today theyre closed and I cant even leave a message. Now I know why the Maytag repairman is the loneliest man in town...

Purchased a new stainless Maytag dishwasher model # MDB4949SDMO ser # F54240259 on 10-20-2015. Installed about three weeks after purchase. This unit is terrible -- has not properly operated or cleaned our dishes since installed. First service came shortly after install. Complaint was unit leaves white film on all dishes. (Soap used is cascade which was recommended by Maytag in owners manual.) Technician installed a new water fill valve because unit wasnt getting enough water. After that unit still no good as unit became noisier and noisier and still leaving white film on all dishes. Second service call: the technician indicated entire noisy pump assembly would have to be replaced and would need to order it. Third service call: the technician arrived and replaced entire pump assembly, taking the old one away with him. The technician said it will be good now. It wasnt, but at least it was quiet. That was in January 2016. This unit still does not clean dishes properly -- continues to leave a white film on everything requiring hand scrubbing to remove. All dishes are hand rinsed with hot water before loading them in dishwasher, but actually dishes are more dirty three hours later after the cleaning cycle has finished than before they were put in. After having to buy new glasses and plastic ware because stubborn white film will not come off and looks disgusting. Tried various different soaps and rinsing products to no avail.Finally contacted service department for the fourth time and today technician arrived and found the unit to be mechanically functioning as it should and can do no more to help. Said to try a product called lemi-shine. Maybe my water is too hard also he said, even though we are on city water! This is our third dishwasher at this home and have never had hard water associated issues. All I want is my full refund for this defective product and I only get the run around from Maytag. Stay away from this machine.

Love my washing machine. It is so big I need a step stool to reach down to the bottom. It cleans my wash well and I have dirty clothes. I hang my clothes on the line outdoors. My clothes have never looked and smell so good.

I wished I researched more before I purchased, but like most people, I believed in the reputation of Maytag. Like many others - my control panel started to go out 19 months after install: Had my first event with the washer; it would not allow me to select normal wash. A high-end machine shouldnt have electrical connection problems within 19 months, just 7 months after the warranty expires.When the repairman pulled apart our machine, he found a similarly burned looking touchpad ribbon cable, that was burned in exactly the same position as the photos shown on Maytags website under the review referred to. Maytag/Whirlpool has set up a special phone number to deal with this problem: I dialed 1-866-931-7384... Been on hold for over an hour Of course - NO answer! Ill try later but I am very angry that this has been a known issue BEFORE I purchased mine at Home Depot. What a piece of junk. This is the last Maytag Ill ever buy again. The service is horrible, the product is junk.

We have a model MF12269VEMS. Approx 3 years old. Ice maker and water dispenser work great. Fridge works well. We have experienced over the last 6 months a buildup of ice that forms inside the freezer under the drawers. If we dont catch it every 4-5 days we cannot open the drawers as the ice catches the bottom plastic drawers. I called Maytag directly and the pleasant young lady told me after checking that it did not seem to be an issue...clearly after looking into the internet I am not alone! Maybe someone can email me a fix?

Unless you’re doing laundry for an army don’t buy the Maytag commercial washer MVWP575GW. I should have gone with my original choice but my husband was concerned with the durability and warranty hence why we purchased this washer. It’s just the 2 of us and I frequently use the delicate cycle. Unknown to me at the time you can not adjust your water level so if you’re washing delicates plan on wasting a lot of water unless you only wash your delicates once a month. In my opinion delicates are undergarments, blouses, etc. delicate cycle in “deep water wash” only. As far as we can tell the wash cycle at its longest is 8 minutes which I guess for commercial grade is probably correct. However there is a presoak option that I don’t the believe does the work of a longer wash cycle. If you have to do a quick scrub on a piece of clothing as the washer is filling up you can not do this as everything stops once the lid is up.Last but not least the washer is loud it sounds like it’s going to break down at any minute. I’m sure many of the issues people have with products today are due to government regulations. I’ve tried contacting Maytag customer service on numerous occasions to see if I’ve been doing something wrong even though I’ve read through the operating manual several times, I’m currently on hold for 20 minutes. Doing the laundry has never been the highlight of my day but I never minded it until now. I absolutely dread it now. My suggestion would be if you like the features on your current washer, spend what you need to to get it working properly which is what I wish I had done with my 23 yr old washer. Worst purchase I’ve ever made!

Turned the oven on, and it failed to light. A little while later, it started leaking gas into the house. Im lucky the house didnt explode!

My husband and I are very disappointed and upset about our new Maytag Dishwasher model MDB8949SBM. We only have had this dishwasher a little over a year! We purchased in May of 2014 and in June 2015 the control panel lights were acting crazy. Actually I even think it started earlier but just thought it was me pushing buttons wrong and wasnt that bad. Then in June any button you push on would not even light up!! I have stopped using dishwasher since June and now it is October! I was so done trying to push the right cycle that I wanted! I will never purchase another Maytag ever!! Just saw there is a Lawsuit here California. Yes!! But I have not seen any information yet on this lawsuit. I am calling Maytag!

I bought my first centennial washer less than four years ago, warrantied that machine out. It was replaced by best buy because of the warranty that I purchased. We are a family of four, with that in mind the replacement machine was a model year newer and it last just over a year and quit. I bought the machine anticipating that it will last me the next 10 years. With two children at home now that is not working, all I have to do on replace a new machine. The repair shop has told me that they get more of the Maytag centennial machines and then any other washing machine is going to cost me more to repair it than to buy a new machine because I had faith in the Maytag products for many many years. This particular machines are extremely hard to diagnose as to what causes the problem or what the problem is and could take a long time to get it fixed as well as the expense of getting it fixed. I would not recommend another Maytag product nor will Maytag ever get any more money from us. This particular product has become a piece of junk that I cant even get rid of to recycling. Maytag has become a joke and this machine has become a 500 dollar hunk of junk in my opinion.

The frontload washer 4000 series began making a very loud noise on spin. I called Maytag and requested service. The technician came and made a diagnostic evaluation, stating this has been a bearing defect affecting several of these models. I called Maytag, and the representative agreed to ship the parts at no charge. A week later, we received the parts, only for the technician to find one of the parts damaged in shipping perhaps. So another part was sent directly to the Maytag dealer. Upon my research, this appears to be a known issue with the Maytag/Whirlpool corporation, and I found where customers had requested Maytag to also be responsible for the service/labor costs, which were also covered by Maytag. I made the call today and was advised no and to be happy that Maytag paid for the parts due to a known defect and that no service or labor charges would be covered. I understand my machine is out of warranty, but this is a known defect; its nothing caused by my self.

I bought a Maytag Bravo washer with the new stainless tub and the bottom agitator. It also has a clear glass lid. Mistake. I can see the action of the washer thru the glass lid and it definitely doesnt wash the clothes very well. They just stay in the same position and the bottom clothes get agitation but the tops ones just sit there. The towels especially smell musty after they have been washed. Probably because they dont get agitation. The water level is so low that the clothes barely get wet. It was a good idea of the company to save water and electricity. But they must not have thought about getting the clothes clean. If I could I would get rid of this machine but I wouldnt want to subject anyone else to this type of washing machine. I would feel badly selling it knowing that it doesnt get the clothes clean. So I would never suggest getting a Maytag washer with a glass lid because you dont want to see what it is not doing.

Our less than five yr old washer finally died. It had been making awful sounds. Started in only very small loads but then started in bigger loads too. It finally stopped altogether. Model number MVWC400XW4. I would NOT recommend this washer.

Yesterday I was using my washer (small load of clothes), I was with my baby in the laundry room when suddenly there was a horrible noise and the door of the washer opened, he hit my back, something fatal could have happened. I do not know how it happened but a piece of concrete was inside the drum. I do not want to imagine what would have happened if that piece came out and hurt my baby. I spoke to the company and explained what had happened to me, but they do not want to be responsible for what happened because the washer is in Tijuana (border with San Diego), I bought the washer in Pirch San Diego California in 2015. Maytag United States is responsible for this defect. Dont buy this model:mhw8100dc extra large capacity washer with steam and powerwash® system-4.5 cu. Ft.

Maytag Bravos XL washer and dryer. Best washer and dryer I have ever owned. I have owned about every major brand and these are by far the best. My husband is a hog farmer and the washer does a great job. I will always purchase Maytag appliances.

As with most other owners I am dissatisfied with the cleaning action of the machine. I suspect, that in an attempt to garner green bonus points, the engineers have tweaked the cleaning water amount to the absolute minimum that may do the job and lengthened the wash cycle to the point that laundry for two average adults is an all day affair. Only get a decent washing job if you make very small loads. If you put a set of king cotton sheet in the machine, you will find that the machine manipulates them into the shape of your compact spare tire, and when you take them out... you will find many sections where the water did not reach... bone dry! Reload, rewash, ground hog day with each load. Cant wait for it to throw a bearing so I can get something else.

I am grateful I dont have to beat my clothes on a rock. Absolutely the worst dryer Ive ever had!!! Previous Kenmore washer was my favorite! This Maytag does not allow me options to stop, soak & freely open & close as I choose. Even my adult children who occasionally use it say its the worst!

I purchase my Maytag electric glass top stove 9 years ago. 2 years ago, one of the burners went out and had to be replaced. Now, in the past 2 days, my oven is taking FOREVER to preheat from 0 to 455 degrees. So far, its been 78 minutes waiting for it to go from 0 degrees to 425! Apparently the heating element is defective. As far as the self cleaning oven, it is absolutely worthless, and does NOT work! Needless to say that Im very disappointed, and looking at another repair expense!

We bought the Maytag Bravos Washer and Dryer set in 2013 after extensive reviews as well as the brand recognition to replace my at least 20 year old Kenmore washer/dryer. At first we were very pleased. The ability to do bulky loads was great and the high spin cycle left the clothes almost dry. In 2018 (keep in mind, just 5 years!) we started to hear a grinding sound in the washer when on rinse cycle and the dryer would randomly turn itself on! Strange but true. I called Maytag Canada and they sent someone right away. They had to replace the motherboard on both the washer and dryer as well as the drum and gears on the washer. Fortunately this was covered under warranty.Fast forward 1.5 years. Same issues with washer...technician came and could not identify the problem, although I did tell him it was the same as 1.5 years ago. I ended up recording the sound and asked them to resend technician to the house. After further diagnostics, yup...same problem. Two days went by and I received a call back advising me that the cost to repair would be over 700.00, not covered by warranty! I escalated to management, to no avail although they did offer me 15% off my next Maytag purchase! Needless to say I have ordered a brand new GE from Costco, arriving tomorrow for basically the same price to repair the Maytag. I will NEVER purchase another Maytag product and will advise anyone who cares to listen to me to do the same. Huge disappointment in the Maytag product, brand name and customer service. 10 year warranty? Not likely...stay away.

Purchased a Maytag - MDB7749AWM1 dishwasher in 2011 from Home Depot. The door seal has failed several times and been replaced by a serviceman. The warranty has since run out but the seal continues to fall out every time you run the dishwasher and open the door. Has anyone else had a similar problem? I have considered gluing the seal in place but cant find a glue that will handle the temperature. Im sure that Maytag will say they have never seen this problem before. Maytag is off my purchase list forever!!!

My complaint sounds just like the others listed here. Purchased Maytag dishwasher MDBH979SAB1 at Home Depot 2/2013. In June 2014, the control panel started to malfunction. When I called Maytag, these were the options given: 1--have it serviced out of warranty at $89-$150 for repairmans trip & diagnostic, which doesnt include parts & labor or 2--obtain something called Repair plus one, which covers the cost of repair and reinstates the warranty for one year at the low cost of $264.95. So either way, Im going to have to pay almost 1/2 of the original purchase price. Ridiculous! We had our previous dishwasher (not a Maytag) for over 13 years, with only minor repairs. We purchased a Maytag because we thought it was a reputable company that stands behind their products---well dont believe it! I would NEVER recommend any of their products.

Model # MF12269VEQ1 French doors with bottom freezer - This refrigerator was purchased March 2011 and it is forming a sheet of ice on the bottom of the freezer. We tried unplugging it overnight to see if it would correct itself and it hadnt. I googled this complaint and called the manufacturer to see if there was a recall. It seems a lot of people are having this problem. Several comments are to pour hot water in the drain plug or use a blow dryer to to the plug; however, you have to disassemble the whole bottom freezer, then unscrew the back to get to the drain plug. I feel this is a defect in this refrigerator.This unit was approx. $1600.00 and should not be having this type of problem. Who knows if I could actually get to it to try these things, that it could keep recurring. Im very upset as my husband and I are seniors on a fixed budget. We bought the name Maytag because we thought they built good products.

My Maytag AquaLift Range MGR8880AS0 was given to me in September 2014. While the range top was excellent and gave me no problem, the so-called self-cleaning is a total joke. I do not do a lot of grease baking or broiling so I have not needed to clean the oven only twice. The first time was a total surprising astonishment. When I opened the oven immediately after the cycle was completed, the oven was not even 350 degrees, most of the water was still in the oven! This happened shortly after a family crisis (my husband became ill and died), so I did not do any inquiries regarding the cleaning failure. Today, January 24, 2018 I decided I would do my second cleaning. Wow, it was a total and complete failure. The oven was barely warm.I always had a Maytag washer, way back in the 1970/1980. My four children grew up with the Maytag, So, I think when one of my children decided to gift me with a new range after a change in location, the Maytag name was at the top of the list. Unfortunately, in 2014 Maytag was no longer what it had been way back in the olden days. The name Maytag does not stand for what it used to stand. End of my story. Thank you for giving me the opportunity to get this off my chest. Since this was a gift, I do not have a receipt. However, I have an insurance renewal due advice (coverage expires 05/24/2018).

My Bravo washer will not wash a set of sheets without dancing across the floor. So irritating to have to run in and separate the sheets that have ended up in a ball. The dryer is ok. Except my old Maytag had a loud buzzer that went off when the cycle was done. My new dryer has a dainty little chime that cant be heard if the washer is going. Wish I had my old set back!

Have had problems with the set since day one. Bought brand new from Home Depot. Got a great deal and now know why. Never cleaned the clothes properly, water marks on so many items, musty smelling regardless of how many times we cleaned it, horrible at removing stains, and finally not even 5 yo the motor stopped worked. The dryer has been repaired too and hasnt ever done a stellar job. Will never buy another Maytag product again!

I am having the same problem with the sheet of ice forming on the bottom of the freezer and leaking water out every week or so. It is getting very frustrating. After reading all these reviews I am realizing it is a manufacturing flaw and think there should be a recall. We have model MF12269VEQ3.

Never buy from Maytag. I and my daughter bought from them two refrigerators of them. After one month my daughter started to fix. I am started after one year or it is leaking. Our freezer destroyed and realize this after one day all my food I throw away. The same was with my daughter refrigerator. My daughter have old refrigerator it is working without problem for 50 year never fixed. Never ever buy from them anything. It is good I was at home. Sometimes I am traveling if it happens this time. I do not want to think about this. For fixing you have to pay lot of money. I hate that I purchased something with them.

Bravos washer, a year old machine, needs new main electronics board $220.00 plus $125.00 labor to install. Repair guy said humidity makes them go out. Go figure a part sensitive to dampness on a wash machine. Why don’t they seal it better? By the way, this machine does not wash, worth a crap. I am getting something new.

In December of 2013 I purchased a Maytag clothes dryer model Neptune. In July of 2014, I was hearing a banging sound as the drum rotated. As a mechanical inclined person that I am I removed the top of the dryer and turned the drum by hand. As I turned the drum I noticed that the stainless steel crimped bead around the drum had separated just enough to hit the side wall of the dryer. I was able to bang down the raised portion of the raised bead. This was a quick fix and there was no more banging as the drum turned around. Then in June of this month it started to make that banging sound again. So I removed the top of the dryer and discovered that the bead separated again and then there was a crack that spread to about 1 1/2 inches. I banged down the raised portion again and this lasted for 2 weeks. That’s when I noticed that the crack spread further apart and actually ripped a hole in the left side wall of the machine and froze in position where it would not turn at all. So I reversed the turn of the drum by hand to allow the drum to turn again. At this point I decided to order a new drum which came to $264.00 which included shipping. When it arrives I will replace the entire drum. Being that Maytag/Whirlpool refused to honor their product because this issue happened after the warranty had just expired and the company didnt want to replace the drum. I have never heard of a dryer drum seal bead coming apart in all my experience with repairing an appliance. No I wouldnt suggest purchasing a Maytag/Whirlpool product to anyone. I feel the company should have done the right thing and replaced the drum. In life if you do the right thing all the time, then there would never be an issue with the consumer and corporation. Always do the right thing and you will never go wrong.

Fridge Model MFF2258VEB6 - Our refrigerator is less that 2 years old and it wont make ice! The bottom of freezer is filled with water that froze. Everyday there is water on the floor. We asked at Home Depot where we purchased it and they said we need to change the filter. What filter? The owners manual is a joke. We cant figure out where the filter is located so it looks like we have to pay money to have someone come look at this. Hey, this is ridiculous. I thought Maytag had a good reputation and thats why we bought ALL Maytag appliances two years ago! Never again!

Purchased my appliance at Lowes in 2012. I have had at least 8 service calls, the unit has NEVER worked as designed. Water leaks inside and out. The ice maker door heater had to be replaced. Fan Motors have gone out on it, broken water tubes. The temperature wont stay consistent, it freezes my refrigerator items, ruptures beverage bottles and cans. This once quiet unit is 3 times as loud than when I bought it. I am so frustrated!!!What a value $2,000 for the appliance, $700 out of pocket for repairs to date, $$ in lost food items, $$ in my time to clean the mildew, water, exploded beverages, cant put a $$ on the embarrassment when family/friends use. What is the potential danger to myself and family when the mildew is in the unit and water leaks into open refrigerator items? Next scheduled repair from my factory authorized repair technician? 10/29/2013.

We are on our 2nd Bravos XL. The first washer lasted 6 years and there was a part going out that kept making it stop in the process. Basically the repair guy said it will just go out one day so it was up to us to repair or replace the machine. The machine didn’t have an agitator and we had been having issues with white residue on the clothes for a long time but thought it was related to the other part. So we bought a new one, with an agitator. It was the new model. We’ve had it around 6 months and we have lots of issues with the white residue. The only success we have with not getting white residue on darks is using deep fill and very little detergent. We use powder because the liquid makes dark spots on our dark clothes. So either way, there’s a problem. So we are using a lot of water when it’s supposed to be water saving. And we are using much less detergent that the company says. I think it’s the machine that has problems. I’ve read a long thread on Facebook and it appears that Maytag tells you to use Affresh regularly. It also says to follow their instructions. But everyone seems to follow instructions but Maytag takes no responsibility for their product. Makes me sad because Maytag was the best on the market at one time and we will never buy again. Our dryer works fine but the washer sucks. And that was a lot of money that I paid. I hope that Maytag decides to make it right and help their “customers” enjoy their products once again.

Save money. I have always had Maytag & loved them until I bought the Bravos xl top load washer. The salesperson insisted it was a large capacity energy efficient w/ great maintenance record -- greatly misleading. The water level does not rise enough to effectively clean or rinse so clothes do not get cleaned or detergent doesnt rinse out thus allowing only 2 to 3 towels or jeans to wash per load. Such ineffective cleaning cycles create the ongoing need for loads to be rewashed and be extremely small, yielding credence to other consumers’ accusations of being mislead and false advertising of xl capacity. As such, it takes hours to wash a family of threes clothes. The machine shakes like crazy and clothes get ruined as they get twisted and tangled into each other ripping, tearing, misshaping and ruining them.

I have a Maytag front load washer, and it has been flashing codes since day one, smells like mold, does not spin water out, and at first, all Maytag could say is, Im using too much soap, the wrong soap, loading too full, and I have it on a stand that is sold with the washer that they dont recommend, after I paid $300.00 for it. Now, it is flashing an E3 code, and will not finish a cycle at all. Maytag wants money to fix the problem that thousands of consumers have, after paying over $1,000 for the machine. I will never purchase another Maytag product, for as long as I live.

We purchased Maytag microwave (MMV4205DH1) less than two years ago. Within the first year, the microwave would not work and we would see an Open and Close Door message. We had it repaired and now 10 months later it is doing the same thing. The cost of repairs is high--the same as a new microwave. We have been inconvenienced throughout the holidays by our broken appliance. Disappointed.

Purchase of what we thought was high quality Maytag dishwasher. Paid $600 and $250 to get it installed, which was really just to take out the old dishwasher we wish now we had kept, and plug in the new one. After 2 years, repairs needed to replace the control panel and key pad must be replaced, cost $340 plus labor. We will never buy Maytag again. Called their hotline, 800-877-6777. They cannot offer any help. Called the co. we bought it from, a Maytag dealer, Haleys Maytag of Antigonish, Nova Scotia. They too offered nothing except to sell us parts... control panel and key pad. Called lawyer who has class action suit now against Maytag, Eppsteiner & Florica. They are not representing customers who live in Canada, only U.S.My recommendation to Maytag dealer who only sells Maytags, Haleys Maytag of Antigonish, Nova Scotia, find another company to represent. Maytag is a real loser. Never again purchase a Maytag, and I told 10 people who will tell 10 people... who will tell 10 people. Our model number... same as all of yours... the loser MDB6709AWW1. Dont waste your money buying this overpriced dishwasher that will then require you to spend more money every 2 years on a Control panel and Key pad that are defective from the factory.

I purchased a Quiet Series 300 E71195 dishwasher in 2011. Its about 3.5 yrs old. I guess misery loves company because like so many other complaints on this site my control board died, and Maytag, while saying they care about customer satisfaction, basically said tough luck pal, youre on your own. Sadly I own 3 other newish Maytag appliances. When will these appliances die without support from Maytag? Im not holding my breath. My next step is to complain to the dept of Consumer Affairs and create a page about nefarious Maytag on social media. Avoid the Maytag brand when shopping for appliances. I know I will.

I purchased a Maytag Bravo washer 2 years ago and it is the worst washer I have ever used. My clothes are never clean. It is always out of balance and is so slow and takes forever to do a load of laundry. It has started stopping on spin and have to unplug it to get it started back then it sounds like a jet coming in for a landing and has to restart the spin about 3 or 4 times before it ever finishes. I have had the repairman to look at it and says there is not anything wrong with it, but something has to be wrong for it to stop on spin and have to unplug it for 5 mins. in order for it to reset itself and start again.

I have been using washing machines for 50 years. This is by far the worse piece of engineering I have ever used! On deep water wash, I would expect my clothes to be covered by water. I actually have to add by hand, four buckets of water and even then the clothes just float on top. The agitator NEVER pulls the clothes down to the bottom of the tub, they just move back and forth. The clothing that sits on top of the water, never gets totally submerged and is still on the top of the pile when the wash cycle is done. I will NEVER buy any MAYTAG product again. Lowes wont help me. I want to sell it, but in all good conscience, I cannot unload this on another person. I cant even feel good about donating it as it does not work...It is Junk!!!! Shame on Maytag for selling a scam. If there was any integrity in this company, someone would contact me and give me a better model.

We purchased our Maytag dryer at Home Depot a couple of months ago. We just called Home Depot for the second time because the dryer handle broke off while opening the front load door. We called Maytag and they tell us to call Home Depot and the only thing they are willing to do again is fix the door handle which will probably break off again while Im in the middle of laundry and cant retrieve clothes from the dryer because there isnt a handle to open it.Im convinced the dryer has a defective handle, and the dryer should be replaced considering what we paid for it. But Maytag or Home Depot doesnt want to do that. I will never buy Maytag products again and thinking of buying products at small appliance stores who stand behind their products, instead of Home Depot who could easily turn our dryer over to the insurance company as defective for the loss.

No matter what we we do we still have soap residue left on clothes, even when we do the 2nd rinse cycle (what a waste of water). We use the correct amount of HE detergent and we use the detergent dispenser but it doesnt helps. The machine just doesnt use enough water. We have removed items that still have DRY SPOTS on them when the cycle is done. Areas that have never gotten wet after a 45 minute cycle. Never once had this happen with an agitator machine. Would not buy this machine again. Model: C80441070. Serial #: MVWX655DW1.

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

I unfortunately just had the same issue concerning my unit. The unit went berserk, stopped cooling and ruined all my food. I managed to get it outside after leaking spoiled food all over my floor. I washed it out and contacted Maytag after reading the hundreds of complaints. They sent someone out to fix the panel but he couldnt get it to cool. He said many times when a unit goes down that the acidity from produce along with moisture can eat through the aluminum components causing a freon leak. Obviously, this happened to me. I contacted Maytag and they said they would fix that too but once I called back, they said that it was a separate issue. Then I spoke with another person who said they would send a tech to inspect. I took off work and finally got a courtesy call from tech saying he was told not to come. I was amazed I missed work waiting and got no call from Maytag saying they changed their mind. I called back in and was told flat out I would not be covered, even though the fridge was fine before this happened. I suggest everyone read over the Consumer Protection Act which covers defective equipment causing issues by both injury and property damage. A class action lawsuit needs to be organized concerning this also. In the meantime, I implore each of you to file a complaint with the Better Business Bureau in your state along with Michigan where Maytag is headquartered. This will guarantee a response from corporate. Also, make copies of this forum and send it to your State Attorney General explaining how you have been sold a defective item. They say ABC news once did a segment on this fridge issue also, so I suggest contacting them asking for a follow-up story. For those that use social media, go onto their Facebook and Twitter page to post a link to this site and the way you have been treated after spending over $2,000 and a fridge that has lasted 7 years or less. Its time for small voices to unite to form one that is much larger.

Washer has plenty of functions for me to was even my work clothes. These saves me money and time. Washer leaves clothes clean and you can even wash your blankets.

We bought a Maytag Bravos XL MCT Washer from Lowes in Oct of 2016. We had cycle issues with it in Sept of 2018 and called the Appliance Repair Service. IT was determined that the Electronic Control board and UIC was bad and needed to be replaced. Estimated cost - +$700.00. We bought Maytag because we thought it was dependable. Not so. Less than two years of use and repairs are more than we paid for machine ($639.00). Receipt would not upload.

Oven door glass shatters after 6 years of having this oven and the company refuses to cover it. According to them it is not a safety concern. It is actually designed to shatter this way. Wow, thats comforting. Should be 0 stars not 1 star.

I purchased my Maytag Refrigerator in Feb 2013. It is model MFF2558VEW7. It has the French doors w/ freezer at the bottom. This past week, I lost everything in the freezer. I call the Home Depot where I purchased it and they said that I have to call Maytag. I did and they sent a repairman out. It needed a compressor. After only 8 months, the compressor goes out? Why should this fridge be repaired and I not be given a new one? With all the problems with the Maytag, there needs to be one big class action filed. I asked for a loaner because it would take up to five work days for them to order the part. The answer was, We do not provide loaners.

Ive had my washer for about two years and have been disappointed from the get-go. I did a lot of research and found this to be top rated... Wrong! Even though I use the HE detergent and Ive even cut down the amount with no results, it leaves gobs of soap/lint residue on most of my darks and I wind up having to either rewash on clear or rinse by hand to get rid of the stuff.Ive also noticed some snagging on some brand new towels, but I attributed that to possibly the brand. Well, then I had an issue with some very expensive bottom sheets shredding and raveling and still didnt catch on. Today I noticed a different towel with similar problems, which led me here and walah! I see Im not the only one having these issues… Darn! Warranty is expired and Im stuck!

Dishwasher model: MDBH949AWW3. Gradually over a months time lost its control functions and its status display. Ten days ago the last button to fail was the start button and the dishwasher stopped working. Maytag confirmed over the phone that there was no recall on this model. The part costs $190 and is out of stock till end of October 2013. I opened the dishwasher and took a closer look at the keypad. It has the cheapest touch buttons I ever seen. Maytag had provided at purchase time a user guide and a large sheet with a sketchy incomplete drawing (W10142800C) for service use only. I made my own schematics and I built my own keypad for less than $50. You may notice that the info I have on my attached schematics is missing from Maytag/Whirlpool incomplete drawing. My keypad is working fine and will outlast all the remaining parts in that dishwasher. I wish there is an angry lawyer out there with a bad dishwasher like mine that will use this info to sue Maytag. Please give the schematics to any user having troubles with this lousy touch pad.

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

I purchased a Maytag Bravos XL washer mid November 2013. Less than six weeks later it leaked water. The repair person has been to repair it four times. The last visit was yesterday. It now has more problems than it originally had. It still leaked water. Maytag does not stand by what they sell. All they say is they will repair it. My caution to anyone reading this is never buy a Maytag appliance. I hope this review helps someone in their decision making process.

I love it. Laundry as well as horse blankets. It does it all! I have never ever had one problem with it. Love the delay start setting as well as the extra rinse cycle.Easy to clean the gasket and keep the soap dispenser out to air between washes!

Bought top of the line Maytag Commercial Technology washer because it was supposed to be the most advanced on the market. My experience has taught me that advanced does not equate to efficient, effective, and expedient. The washer settings for an average load (sheets or towels or clothing) is about 111 minutes per load (nearly 2 hours!!). To adjust to what would be a quick wash is about 25-30 minutes BUT the washing part of that is only about 5-7 minutes. I feel like a Pioneer Woman because I must spend most of a day to run four (4) loads of laundry (sheets, towels, dark clothing, white clothing). This is extremely frustrating!! I am sorry I purchased this product.

Oven racks falling down and theres appears to be no solution because the interior liner of the oven has warped. The 3rd party repair guys tell me the interior liner needs to be replaced, its not worth the repair cost, Im better off shopping for a new set. Its so unfortunately that this happened (we moved into this house with existing appliances that we cannot use...) and it seems to be a common problem, yet Maytag claims they have NOT received any complaints about this.

I bought a Maytag dishwasher MDB7749AWM1 in May of 2011. Yesterday, the on button would not work, so I called a serviceman out from Maytag. He said the whole panel needs to be replaced, parts and service will cost me $240.00. What a shame. 2 months out of warranty. I had two previous Maytag dishwashers, lasted for years with no problem. The newer models are junk, do not buy them! I can see by the other complaints that they had the same problem. They do not stand behind their product. I wonder how long the new panel will last? Im done with Maytag products!

Purchased a Maytag Electric Range on Jan/9/2016 and delivered Jan 12/2016. To start the Aqua Steam clean is for the birds. Does not clean worth a darn. Model MER8600DH cost $823.33 and I thought this unit was awesome until December 2018. The oven makes loud bangs and it’s not metal contracting or whatever. I stopped using my oven. Tonight my top burner started snapping like an arc or short. Yup that’s it for me. I was thinking of buying a Maytag Gas Range as I was brought up on gas and I have a plumber coming this weekend to plumb for Natural Gas but after reading all the negativity on the gas ranges as well I absolutely will not be buying a Maytag now or ever! I expected more from Maytag. :(

I bought an off-white or light cream color gas Maytag stove about three years ago. When I first used it to boil some water for tea, the light colored grills turned black. And this is without cooking a full meal, merely boiling water. After a few more uses with light cooking, and a few spills on the cooktop, I discovered that it was simply impossible to clean. The glass on the oven door became discolored with the first use, and is also impossible to clean. I purchased several types of cleaning items and sponges, and nothing works. This is a disgusting stove. I hate it and I wish I never bought it. I will never purchase a Maytag anything ever again. Its the poorest and cheapest no-quality item - a total waste of money.

My dishwasher is less than 2 years old. Dishwasher will go on when we are not in the house. Cant control the panel. The control panel lights all come, have to cancel to stop the machine. This could be a fire hazard.

I purchased a Maytag self-cleaning stove in early 2009. Right away, the oven floor finish started to bubble up. I called Maytag service and was told the part wasnt covered. I let it go since it wasnt interfering with the function of the oven. However, in Feb 2012, the oven started turning off in temps above 350. I called Maytag service again and was told that since I didnt purchase an extended warranty, I would have to pay for the service call, parts and labor. I complained that I never expected their product to break down in less than three years.I had a private oven service look at it and was told the computer part was the problem and would cost almost $300 to replace; or I could just live with an oven that didnt go above 350 and buy a new one when it broke completely. You can be sure I will never, never purchase another Maytag product or any other product they involved with like Whirlpool. I am done with them and their inferior workmanship.

Same issue as everyone else. Bought the French door with middle deli drawer fridge November 2012 at Home Depot. After 2 1/2 years freezer drain froze up leaking water into the floor. Spent 6 hours fixing it. Now still less than 3 years old the ice maker is not working. Not a jam or water supply issue. Just dead. Looking into replacing the ice maker. Such a disappointment. Only thing this fridge is good for is its looks. Obviously common repeated defects. Wake up Maytag and accept some responsibility.

I bought this dishwasher from Sears on Tuesday July 15, 2014. It was delivered on Friday July 18, 2014. On Friday July 25, 2014 two plastic clips that hold the top rack on broke, and one whole side of the top rack fell down. I called the 1-800 # in the book. Then I called the repairman they recommended. He came out on the Monday July 28, 2014. By the time he got here, the clip on the other side broke. Now the rack was hanging by one plastic clip. While waiting for these parts, the last clip broke and the rack was completely detached. So he received the parts on Friday Aug. 1, 2014. When he arrived, lo and behold, they sent the wrong parts. He had the side tracks that hold the rack, not the cheap plastic clips that attach it to the racks. So I have had my new dishwasher 14 days, and have been able to use it a total of 4 times before it failed. I am now awaiting the new parts. The parts that broke are made from a cheap thin plastic, and this is expected to hold up the entire top rack and the dishes its holding.

I bought the Maytag Bravos XL HE washing machine because I needed a machine that could handle large loads to save me time doing multiple loads for everyday items like jeans to towels, blankets as well as delicates. This machine is a COMPLETE disappointment. It does NOT get anything clean unless I wash it 4 times with bleach and pre-stain 4 times. You know what bleach does to your clothes! The water level is so low I can only wash 4 things at a time and I still have to wash additional times. It doesnt get the smell or food stains out. Not a good choice for an active family or person. Ive had clothes come out with suds still on them after washing three times. I use less than the recommended amount of HE detergent. There was a $250 agitator washer by GE at Lowes but it was smaller - how I wish I bought it. These impeller HE machines dont work. My advice steer clear of this Maytag product unless you like to waste your time re-doing loads of laundry.

Worst washer ever. My clothes I have to wash a few times before they all get wet. Not a good washer at all. Has all the bells and whistles. Lets me know when the washer is done or its unbalanced... my washer is crap. Ive had it maybe a year now. I now have to buy another one. Why? Because this one sucks literally... its Maytag commercial technology.

I purchased a very expensive set of Maytag washer & dryer (topload washer) and heavy duty larger capacity. Firstly- I purchased this through Home Depot on Labor Day weekend and did not receive this set until December 2020. This set has all the electronics and Im going to tell you NOT to purchase either one. The dryer MUST have a metal solid vent. This sets your dryer out into the walkway of a laundry room. If you use a heavy flexible metal vent; your sensor will be going off constantly telling you your vent is plugged and to clean it. I had a dryer vent company out twice to clean and inspect the wall & roof vents yielding nothing. I also have a dryer vent cleaner which I hook up to my vacuum and I clean the dryer vent monthly. If you lose power. You will need to unplug your dryer and let it reset to be able to use it.The washer is also terrible for the outrageous price. Again; glass heavy duty top load with all the electronics. You cant get the washer to fill even on deep fill. Also; do NOT put a lot of clothes or jeans or blankets in this machine. It will not be able to level and spin. When you try to use the drain and spin cycle; the sensor keeps going off. I swift the contents around and around and finally end up having to take soaking wet cloths out into the garage until I have one sheet in the machine and it will spin out. In addition- the CLEAN with Afresh mess. This forces you to clean your machine- whether you are in the middle of trying to get clothes drained or not.Buy something thats a simple workhorse with one button. Stay away from any bells and whistles because its only going to cause you heartache in the long run. I wish I would have read reviews prior to spending $1,700 on a Maytag Washer Dryer set (ON SALE- for God sakes). This is the biggest piece of garbage I have ever purchased. Buyer beware.

Maytag Dishwasher, mdb7749sam1 - I got this dishwasher new in Feb. 2013 for my new house. I thought that Maytag was supposed to be a very good appliance company. (I just found out that Whirlpool bought them! I dont like their dishwashers, either! Ive had 3 whirlpools that only lasted about 2-4 years each.) My dishwasher worked great until the control panel buttons started blinking and going crazy! Then, it just stopped working altogether. I called Maytag about this part, and found out that it is only covered the first year, and the so-called 10-year warranty doesnt cover it. What good is the extended 10-year warranty if it doesnt cover all the parts!? I researched this dishwasher before I bought it. It got fairly good reviews at the time. Now when I look it up, it gets these terrible reviews! I am so disappointed with this situation. I have other Maytag appliances that have performed great. Im not sure why their dishwashers cant be made the same way.I am going to order the part and repair the machine. I hope this will fix the problem. I had hoped that the Maytag brand would live up to their hype, and be better than the Whirlpools I had already had such bad experiences with. The Whirlpools had great features, they just didnt last! This dishwasher, too, has great features. Two years isnt a long enough run for it to be a good choice, though. Really disappointed :(

After writing a polite but stern complaint to several of the executives at Maytag and Whirlpool we got a call from their executive assistant. She arranged to have a technician come out to our house and assess the installation. He found nothing wrong and Maytag replaced the control panel for free. The technician has seen numerous faulty electronic control panels, and not just with Maytag. He would not recommend a preferred make or model. He longed for the old mechanical timer switches, which we could no longer find in the newer models. With enough customer complaints maybe they will do something about the electronic control panel in the future.

We purchased a Maytag Jet Clean Plus in August of 2013. Within 8 months the control panel stopped working. Though it was replaced by one of their technicians it now after 9 months is broke again. How can this be such a crappy product??? Over 800 dollars for a dishwasher to have to go out twice in less than 2 yrs is just wrong. The company needs to stand behind their products!!! I will never buy Maytag again and will advise anyone looking to not waste their money!!! VERY DISAPPOINTED!!!

We had a Whirlpool stove/oven for many years, and it was finally time to trade it in. Everything about that unit was good. While shopping for another Whirlpool, the sales rep told us that Maytag and Whirlpool are one and the same. That we found, is false. An important feature for us in an appliance is the self cleaning oven. The Maytag oven had to be leveled four times after it was installed, in order for the self clean feature to function. The self clean part is only a small indented portion of the bottom of the oven, not the entire oven. And even that does not clean. After going through the dealership service about this problem, I contacted Maytag. My final frustrated summary to the rep was that I understand that we bought a lemon, and you are not going to help us in any way. I just want to say to anyone considering a Maytag stove and oven, raise your standard. If you choose Maytag, you will only be disappointed. I am.

13 months after purchasing MDB7749SBM3 dishwasher this lights started making no sense. For me the buttons still work, but it seems like only a matter of time until they stop working too. Like many others, I opened up the door and found the corroded ribbon connector (see photo). It wasnt damp so since the corrosion happened at the point where a ridge of plastic presses the ribbon against the hot handle, I suspect heat. Obviously a design flaw. Come on Maytag. Recall?

I bought a Maytag dishwasher in April 2012. The electronic control panel failed in October 2013. Repair quote was $250, and there is no guarantee that the new control panel will not suffer the same consequences. My research has revealed that this is a very common problem with the dishwasher experienced by a large amount of owners, all about at the 18-month mark. I contacted the company and was chastised for not purchasing the extended warranty and was basically told, Too bad so sad. Buyer beware, do your research before you purchase this appliance. I will never buy a Maytag appliance, or any brand associated with the Maytag name.

Bought the Maytag high efficiency washing machine with the auto-sensing and deep water wash feature. It took some getting use to because of all the washing choices and different noises it makes. Auto-sensing seems to use very little water which is strange but clothes seem to come out clean. Best bet for me is like the old school way and use deep water wash and light load which is shorter and thats most efficient power wise but will use more water which is fine by me. Also bought the matching dryer and thats a 5 star review. Excellent product.

My Maytag microwave caught fire and burned our cabinets and wall. We had just arrived home from vacation and our fire alarm went off. No one was using the microwave at the time, it just caught fire. We put the fire out with the extinguisher and called the fire department. Our wall and cabinet are charred and our house smells of burnt plastic and is covered with the residue from the extinguisher. Maytag sent a technician to investigate the microwave and, just like the fire department, determined that the cause was internal within the microwave. A Maytag agent called us and offered us 10% off a new microwave and 15% when we told them our house had been damaged plus we wouldnt have to pay tax. Theyd even deliver and install it for free. According to my estimation, thats probably less than $50. They told me that the microwave had no value and tried to make it seem as though they were being generous. Its an 11 year old microwave but there should be some kind of warning that they spontaneously combust after a certain period of time. If the microwave had just stopped working because of age, that would have been understandable and I would have just purchased another the next day. Instead these microwaves just self-destruct and Maytag seems to be ok with that. I was not surprised that they had a 1.5 star review when I came here. I have 4 kids, ages 2-9, who wouldnt sleep that night because they were afraid of the microwave.

I purchased a new Maytag range (gas) in June of 2012 - 6 months ago. I have had the same problem many others have had (as Ive just read) with the toxic smell every time I used the oven. I was told it was just the chemical burning off from being new. I have never owned a new oven so I took their word for it. On Christmas day, my kids and I were going to bake cookies and set the oven to preheat. Flames and black smoke were shooting out of the range, and the fire department was called. Even after the fire department put out the fire and removed the stove from my kitchen to my front porch, they spent more time investigating the situation to make sure my home was safe than the certified Maytag repair person that was dispatched out by Maytag to service the range. This stove is only 6 months old and still under warranty with Maytag. The service person they sent out did not take the stove apart and spent less than 5 minutes looking it over; then he determined that it was a grease fire caused by owner’s negligence. I disagreed with him and told him I have been cooking for many years and thought he did not do a thorough job to determine the problem with the range. He got very upset with me, took his bag and left without leaving me a service slip. I asked Maytag to send someone else out and explained to them that this service person did not do a sufficient job in examining the range, nor did he perform any kind of service to get the range back in working condition. Maytag claims they will not send anyone else out, and there is nothing more they will do for me. They say it is my fault it caught fire; and if I want it fixed, I have to pay for it myself even though it is still under warranty with them. My stove is still on my porch where it has been since Christmas day. I then visited Maytags Facebook page and corresponded with others whom have had similar issues with their products and the lack of customer service from this company. Maytag has now blocked me from commenting on their Facebook page. The customer service rep on that site asked me to email her all my information about the range and my issues with it, and she assured me she would respond to the matter. As of yet, I have heard nothing back. I am terribly dismayed by the way I have been treated by this company, their so-called certified service technician, and that they do not honor their warranties or stand by their products. I am cooking for a family of 5 in a 12-year-old microwave (which is not a Maytag by the way) after spending over $600.00 on a brand new range.

I bought a Maytag Bravos washing machine from Lowes in Ocala in Feb 2017. It broke in March 2017. I was referred to a company called Fields Appliance in Orlando Fl. I scheduled a repair under warranty last Friday between 1-4 pm. No one showed up. No one called. I called and called and nothing. BEWARE.

I purchased this product at an authorized Maytag dealer sixteen months ago (Maytag front-Loading washer, model MHWE55OWW1) for approximately $1,500. The main bearing and drum are now shot. Maytag has acknowledged that it is likely defective. Notwithstanding their conclusion, Maytag has chosen not to offer a repair or replacement. The conclusion is simply that Maytag does not make a very good product, and any prospective purchasers can expect that they will not get any customer support for their products.

I have the Maytag Direct Drive Motor washing & dryer set the is supposed to be “commercial technology.” The washer is supposed to keep wet clothes fresh if they don’t make it to the dryer right away. After 2 years, I disagree in that it offers no better outcome than the much older machine I replaced. Furthermore the dryer cuts off leaving my clothes damp every single time, which I cannot stand. It leaves my clothes to wrinkle terribly and damp to stink if I do not collect them fast. I honestly wish I still had my old set. All the new features simply fail to measure up not to mention over complicate and add expense to repairs.

I purchased a Maytag double door refrigerator in 2012. So far the deli drawer has broken 3 times in the same way. There is a plastic peg attached to a side panel on the refrigerator. This pin breaks off after a few months of use. To repair it, you have to replace the entire side panel. The parts and labor costs are about $200 each time. It is obviously a design flaw that Maytag should fix. If you repair it every time it breaks, in about 8 years your repair costs are more than your original purchase price for the refrigerator. Dont buy Maytag products. They are inferior.

Maytag may have pay to replace defective controls. 1-866-931-7384 is the number to call. I have owned my maytag dishwasher for about 18 months. Its control panel was never great, but now my dishwasher wont work at all. Apparently, the tiny inside the control panel rust away because they arent sealed.

We bought our Maytag Bravo top loader on May 5, 2010. The machine was working fine. Then last week with no warning, the F51 error code popped up. We called Sears and they sent a repairman out. The result was the sensors work independently from each other (tested correct in the Ohms range). It made it through an entire diagnostic test, but will not complete a wash cycle. The repair guy concluded that the control board was bad. Estimated cost to fix was upwards of $400. I cannot afford to fix. Our issue with this product is that it is apparent, from reading all the forums, that this is a known issue. And we believe Maytag should be reimbursing consumers for this repair or they should recall the washer. Our washer is used on the weekends and it should have lasted us for minimally five years. All we wanted was to make it through one military overseas tour with it, not asking much. Instead, this machine lasted two years. Unacceptable.

I purchased a Maytag Washer Bravos Quiet series 300 & a Dryer Bravos Quiet series 400 w/ steam in June 2009 from Lowes. I cant express my dissatisfaction in strong enough language with these products. From the time they were installed there were problems.The Bravos series 300 washer: Quiet? Never. The thing sounds like a huge motor whirring around my laundry room. Several times, a coin got stuck in the motor and created a clanking sound that had to be fixed. Ive never had a washer that allowed coins to enter the motor. I cant close the lid on the washer until the whole unit is dry because of the mold problem. I dont feel the washer really gets clothes clean. When we purchased the unit, the Lowes salesman stressed that we could fit a large bedspread into the oversized tub and get it clean. This didnt turn out to be true. The clothes tangle terribly and the unit is off-balance with any kind of a larger load. Ive been forced to purchase the extended warranty because of the complete & total lack of confidence I have in this awful washer (same goes with the dryer).The Bravos series 400 Dryer: This unit never dries. All the setting that should be used with the sensor never work which causes a huge problem. I start out on a particular setting with a stated time limit say, for instance 45 minutes. 45 minutes later, I look at the dryer and theres 1 hr of time still left to go! The dryer just runs on and on. Ive taken to using only the timed dry and I start out at 1 hr, then check it every 10 minutes or so. This is very hard on the fabrics and has caused the useful life of my clothes to be greatly diminished. Also, the stupid thing will start to beep and I cant figure out why. Using this dryer has increased the electricity costs to us.I cant stress enough to STAY away from these products. I purchased Maytag because of their prior good reputation. That reputation is in tatters now. They should recall this product and replace it with products that actually do what they advertise!

I wish I had seen these reviews before purchasing this machine. The plastic tub cracked and leaked all over laundry floor after only 30 loads. Part is unavailable. We will have to wait 3-6 weeks for a repair. Manufacturer will not agree to providing a new machine. Machine is only 3 months old.

The freezer will frost up and the shelves will not move. Repairman has been out three times, once to clean the drain. The second time he installed new tracks for 250.00. Two hours later they still wont move. The third time out he said it was repaired, but two hours later they didnt move again. We are very disappointed with Maytag.

We purchased the Maytag Neptune washer and dryer on May 2005. We purchased it for $2,000. We have had so many problems as we have replaced the drain pump 2 times because of objects getting stuck in it. We have also replaced the door switch, as well as flooding my laundry room floor several times.In 2006, we received a notice of recall. We responded to the recall and were supplied with a GFCI plug for our washer, as this was to prevent the control board from catching on fire. In September 2011, the control panel on the Neptune washer failed. I now have to purchase a new washer, as this is an expensive fix. With this poor workmanship and problems that we have encountered, I am very disappointed. This was a lot of money to spend on a washer, only to last 6 years.

My husband and I purchased a new Maytag dishwasher in March of 2012 at a cost of around $650. There is only the two of us at home and I only run the dishwasher 2-3 times per week. On June 16th, I went to run the dishwasher and it would not turn on after hitting the start button. The cycle buttons lit up but the dishwasher would not start. I called the service number in the user instruction manual and talked to a service representative. I was told that the electronic panel that runs the dishwasher is not covered under the 2nd-10th year limited warranty. It would cost around $291 to fix including parts and labor. When I asked for a qualified Maytag repair service company in my area, she only had one company to give me. This company does not have a very good local reputation so I preferred not to use it. My question is - How can a part that runs the dishwasher not be covered under the warranty? If the start button on the control panel is defective then the machine will not work. I also have a model MDB7749AWW2. After reading some of the 356 complaints about this very dishwasher, I think the Maytag Company must be well aware that there is a problem with this machines control panel and they are choosing to disregard the customer. My old dishwasher was a Kenmore and it ran for 27 years and I only had to replace the motor once. I will not be buying anything Maytag in the future.

As all the other reviews day 1 Dryer had no heat, washer unbalanced and knotting all the clothes. Sent out new dryer after trying to fix to no avail. One month after new dryer, normal cycle continues to run and not turn off. Repairs again - new computer board. Now washer is winding high pitch noise level - repair new bearings. Thank goodness for warranty. But washer and dryer act up again. I purchased extended warranty. Washer tub needed replacing because transmission went out, dryer again control panel problems. Last night the dryer started on FIRE. I’m sure because the control panel normal was not working again after it was replaced less than 2 yrs ago. Total time owned 6 miserable years. Going back to basics, ugh....

The washer does not clean clothes. Thank goodness I bought a 4-year warranty because they have been out 4 or 5 times on washer alone. The dryer is now squealing and shuts off (a safety feature I am sure). The repair person replaced the pulley system and one belt, it still squeals and shuts off. I called the Maytag CEOs office and talked to a machine. Some really nice lady called me back and said she cannot do anything to help me. They have no consumer person to help you and troubleshoot with you. The washer is rusting, it is an inside washer. I live in SE, Texas and they told me it was due to living close to the coast. Well, Ive had GEs that never rusted and in fact, the problem is really with all the HE washers. I hate them. They do not clean clothes. I will never buy another Maytag or Whirlpool product again.

I can’t seem to get any help with my dryer. I have replaced the drum 2 times and thermostat 3 times. Model number is mde9700ayw. Serial number is 13229569gp. I simply want a new dryer that works.

I bought a new Maytag dishwasher 9 months ago from Costco - Maytag 24 in. Built-in Dishwasher with PowerBlast Cycle, White. This dishwasher needs a new motor - Please do not buy this dishwasher. It is garbage.